diff options
| -rw-r--r-- | arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 19 | ||||
| -rw-r--r-- | arch/arm/mach-ux500/board-mop500-pins.c | 75 |
2 files changed, 19 insertions, 75 deletions
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi index 854a4a6e521e..addfcc7c2750 100644 --- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi +++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi @@ -721,6 +721,25 @@ }; }; }; + + wlan { + wlan_default_mode: wlan_default { + /* + * Activate this mode with the WLAN chip. + * These are plain GPIO pins used by WLAN + */ + default_cfg1 { + ste,pins = + "GPIO226_AF8", /* WLAN_PMU_EN */ + "GPIO85_D5"; /* WLAN_ENA */ + ste,config = <&gpio_out_lo>; + }; + default_cfg2 { + ste,pins = "GPIO4_AH6"; /* WLAN_IRQ on UART1 */ + ste,config = <&gpio_in_pu>; + }; + }; + }; }; }; }; diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c index 4535702a8e3f..d0d527a3d205 100644 --- a/arch/arm/mach-ux500/board-mop500-pins.c +++ b/arch/arm/mach-ux500/board-mop500-pins.c @@ -16,19 +16,11 @@ #include "board-mop500.h" -enum custom_pin_cfg_t { - PINS_FOR_DEFAULT, - PINS_FOR_U9500, -}; - -static enum custom_pin_cfg_t pinsfor; - /* These simply sets bias for pins */ #define BIAS(a,b) static unsigned long a[] = { b } BIAS(pd, PIN_PULL_DOWN); BIAS(in_pu, PIN_INPUT_PULLUP); -BIAS(in_pd, PIN_INPUT_PULLDOWN); BIAS(out_lo, PIN_OUTPUT_LOW); BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0)); @@ -38,8 +30,6 @@ BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0)); /* These also force them into GPIO mode */ BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED); BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED); -BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL); -BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL); BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED); BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED); @@ -317,8 +307,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = { * and SSP1 ports (previously connected to the AB8500) as generic GPIO lines. */ static struct pinctrl_map __initdata hrefv60_pinmap[] = { - /* Drive WLAN_ENA low */ - DB8500_PIN_HOG("GPIO85_D5", gpio_out_lo), /* WLAN_ENA */ /* * XENON Flashgun on image processor GPIO (controlled from image * processor firmware), mux in these image processor GPIO lines 0 @@ -384,27 +372,6 @@ static struct pinctrl_map __initdata hrefv60_pinmap[] = { DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */ }; -static struct pinctrl_map __initdata u9500_pinmap[] = { - /* WLAN_IRQ line */ - DB8500_PIN_HOG("GPIO144_B13", gpio_in_pu), - /* HSI */ - DB8500_MUX_HOG("hsir_a_1", "hsi"), - DB8500_MUX_HOG("hsit_a_2", "hsi"), - DB8500_PIN_HOG("GPIO219_AG10", in_pd), /* RX FLA0 */ - DB8500_PIN_HOG("GPIO220_AH10", in_pd), /* RX DAT0 */ - DB8500_PIN_HOG("GPIO221_AJ11", out_lo), /* RX RDY0 */ - DB8500_PIN_HOG("GPIO222_AJ9", out_lo), /* TX FLA0 */ - DB8500_PIN_HOG("GPIO223_AH9", out_lo), /* TX DAT0 */ - DB8500_PIN_HOG("GPIO224_AG9", in_pd), /* TX RDY0 */ - DB8500_PIN_HOG("GPIO225_AG8", in_pd), /* CAWAKE0 */ - DB8500_PIN_HOG("GPIO226_AF8", gpio_out_hi), /* ACWAKE0 */ -}; - -static struct pinctrl_map __initdata u8500_pinmap[] = { - DB8500_PIN_HOG("GPIO226_AF8", gpio_out_lo), /* WLAN_PMU_EN */ - DB8500_PIN_HOG("GPIO4_AH6", gpio_in_pu), /* WLAN_IRQ */ -}; - static struct pinctrl_map __initdata snowball_pinmap[] = { /* Mux in SSP0 connected to AB8500, pull down RXD pin */ DB8500_MUX_HOG("ssp0_a_1", "ssp0"), @@ -426,47 +393,8 @@ static struct pinctrl_map __initdata snowball_pinmap[] = { DB8500_PIN_HOG("GPIO216_AG12", gpio_in_pu), /* WLAN_IRQ */ }; -/* - * passing "pinsfor=" in kernel cmdline allows for custom - * configuration of GPIOs on u8500 derived boards. - */ -static int __init early_pinsfor(char *p) -{ - pinsfor = PINS_FOR_DEFAULT; - - if (strcmp(p, "u9500-21") == 0) - pinsfor = PINS_FOR_U9500; - - return 0; -} -early_param("pinsfor", early_pinsfor); - -int pins_for_u9500(void) -{ - if (pinsfor == PINS_FOR_U9500) - return 1; - - return 0; -} - -static void __init mop500_href_family_pinmaps_init(void) -{ - switch (pinsfor) { - case PINS_FOR_U9500: - pinctrl_register_mappings(u9500_pinmap, - ARRAY_SIZE(u9500_pinmap)); - break; - case PINS_FOR_DEFAULT: - pinctrl_register_mappings(u8500_pinmap, - ARRAY_SIZE(u8500_pinmap)); - default: - break; - } -} - void __init mop500_pinmaps_init(void) { - mop500_href_family_pinmaps_init(); if (machine_is_u8520()) pinctrl_register_mappings(ab8505_pinmap, ARRAY_SIZE(ab8505_pinmap)); @@ -479,8 +407,6 @@ void __init snowball_pinmaps_init(void) { pinctrl_register_mappings(snowball_pinmap, ARRAY_SIZE(snowball_pinmap)); - pinctrl_register_mappings(u8500_pinmap, - ARRAY_SIZE(u8500_pinmap)); pinctrl_register_mappings(ab8500_pinmap, ARRAY_SIZE(ab8500_pinmap)); } @@ -489,7 +415,6 @@ void __init hrefv60_pinmaps_init(void) { pinctrl_register_mappings(hrefv60_pinmap, ARRAY_SIZE(hrefv60_pinmap)); - mop500_href_family_pinmaps_init(); pinctrl_register_mappings(ab8500_pinmap, ARRAY_SIZE(ab8500_pinmap)); } |