aboutsummaryrefslogtreecommitdiff
path: root/Documentation/powerpc
diff options
context:
space:
mode:
authorLi Yang <leoli@freescale.com>2006-10-02 20:08:59 -0500
committerPaul Mackerras <paulus@samba.org>2006-10-04 15:24:27 +1000
commit9a1ab883c04e43f9f9819c40eb435bcdc4136193 (patch)
treefb4d76f1319e83bd02986c78550fb92fbd36e794 /Documentation/powerpc
parent5a3e3b2230980cf2ce6e5e56b816dde19b993939 (diff)
downloadlinux-linaro-stable-9a1ab883c04e43f9f9819c40eb435bcdc4136193.tar.gz
[POWERPC] Add QE device tree node definition
OF device tree node spec used in QE/8360 support patches. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jiang Bo <Tanya.jiang@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Diffstat (limited to 'Documentation/powerpc')
-rw-r--r--Documentation/powerpc/booting-without-of.txt252
1 files changed, 252 insertions, 0 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index 5c0ba235f5a5..b57e7da78976 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -1441,6 +1441,258 @@ platforms are moved over to use the flattened-device-tree model.
descriptor-types-mask = <012b0ebf>;
};
+ h) Board Control and Status (BCSR)
+
+ Required properties:
+
+ - device_type : Should be "board-control"
+ - reg : Offset and length of the register set for the device
+
+ Example:
+
+ bcsr@f8000000 {
+ device_type = "board-control";
+ reg = <f8000000 8000>;
+ };
+
+ i) Freescale QUICC Engine module (QE)
+ This represents qe module that is installed on PowerQUICC II Pro.
+ Hopefully it will merge backward compatibility with CPM/CPM2.
+ Basically, it is a bus of devices, that could act more or less
+ as a complete entity (UCC, USB etc ). All of them should be siblings on
+ the "root" qe node, using the common properties from there.
+ The description below applies to the the qe of MPC8360 and
+ more nodes and properties would be extended in the future.
+
+ i) Root QE device
+
+ Required properties:
+ - device_type : should be "qe";
+ - model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
+ - reg : offset and length of the device registers.
+ - bus-frequency : the clock frequency for QUICC Engine.
+
+ Recommended properties
+ - brg-frequency : the internal clock source frequency for baud-rate
+ generators in Hz.
+
+ Example:
+ qe@e0100000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ device_type = "qe";
+ model = "QE";
+ ranges = <0 e0100000 00100000>;
+ reg = <e0100000 480>;
+ brg-frequency = <0>;
+ bus-frequency = <179A7B00>;
+ }
+
+
+ ii) SPI (Serial Peripheral Interface)
+
+ Required properties:
+ - device_type : should be "spi".
+ - compatible : should be "fsl_spi".
+ - mode : the spi operation mode, it can be "cpu" or "qe".
+ - reg : Offset and length of the register set for the device
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+ Example:
+ spi@4c0 {
+ device_type = "spi";
+ compatible = "fsl_spi";
+ reg = <4c0 40>;
+ interrupts = <82 0>;
+ interrupt-parent = <700>;
+ mode = "cpu";
+ };
+
+
+ iii) USB (Universal Serial Bus Controller)
+
+ Required properties:
+ - device_type : should be "usb".
+ - compatible : could be "qe_udc" or "fhci-hcd".
+ - mode : the could be "host" or "slave".
+ - reg : Offset and length of the register set for the device
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+ Example(slave):
+ usb@6c0 {
+ device_type = "usb";
+ compatible = "qe_udc";
+ reg = <6c0 40>;
+ interrupts = <8b 0>;
+ interrupt-parent = <700>;
+ mode = "slave";
+ };
+
+
+ iv) UCC (Unified Communications Controllers)
+
+ Required properties:
+ - device_type : should be "network", "hldc", "uart", "transparent"
+ "bisync" or "atm".
+ - compatible : could be "ucc_geth" or "fsl_atm" and so on.
+ - model : should be "UCC".
+ - device-id : the ucc number(1-8), corresponding to UCCx in UM.
+ - reg : Offset and length of the register set for the device
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - pio-handle : The phandle for the Parallel I/O port configuration.
+ - rx-clock : represents the UCC receive clock source.
+ 0x00 : clock source is disabled;
+ 0x1~0x10 : clock source is BRG1~BRG16 respectively;
+ 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+ - tx-clock: represents the UCC transmit clock source;
+ 0x00 : clock source is disabled;
+ 0x1~0x10 : clock source is BRG1~BRG16 respectively;
+ 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+
+ Required properties for network device_type:
+ - mac-address : list of bytes representing the ethernet address.
+ - phy-handle : The phandle for the PHY connected to this controller.
+
+ Example:
+ ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ model = "UCC";
+ device-id = <1>;
+ reg = <2000 200>;
+ interrupts = <a0 0>;
+ interrupt-parent = <700>;
+ mac-address = [ 00 04 9f 00 23 23 ];
+ rx-clock = "none";
+ tx-clock = "clk9";
+ phy-handle = <212000>;
+ pio-handle = <140001>;
+ };
+
+
+ v) Parallel I/O Ports
+
+ This node configures Parallel I/O ports for CPUs with QE support.
+ The node should reside in the "soc" node of the tree. For each
+ device that using parallel I/O ports, a child node should be created.
+ See the definition of the Pin configuration nodes below for more
+ information.
+
+ Required properties:
+ - device_type : should be "par_io".
+ - reg : offset to the register set and its length.
+ - num-ports : number of Parallel I/O ports
+
+ Example:
+ par_io@1400 {
+ reg = <1400 100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "par_io";
+ num-ports = <7>;
+ ucc_pin@01 {
+ ......
+ };
+
+
+ vi) Pin configuration nodes
+
+ Required properties:
+ - linux,phandle : phandle of this node; likely referenced by a QE
+ device.
+ - pio-map : array of pin configurations. Each pin is defined by 6
+ integers. The six numbers are respectively: port, pin, dir,
+ open_drain, assignment, has_irq.
+ - port : port number of the pin; 0-6 represent port A-G in UM.
+ - pin : pin number in the port.
+ - dir : direction of the pin, should encode as follows:
+
+ 0 = The pin is disabled
+ 1 = The pin is an output
+ 2 = The pin is an input
+ 3 = The pin is I/O
+
+ - open_drain : indicates the pin is normal or wired-OR:
+
+ 0 = The pin is actively driven as an output
+ 1 = The pin is an open-drain driver. As an output, the pin is
+ driven active-low, otherwise it is three-stated.
+
+ - assignment : function number of the pin according to the Pin Assignment
+ tables in User Manual. Each pin can have up to 4 possible functions in
+ QE and two options for CPM.
+ - has_irq : indicates if the pin is used as source of exteral
+ interrupts.
+
+ Example:
+ ucc_pin@01 {
+ linux,phandle = <140001>;
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0 3 1 0 1 0 /* TxD0 */
+ 0 4 1 0 1 0 /* TxD1 */
+ 0 5 1 0 1 0 /* TxD2 */
+ 0 6 1 0 1 0 /* TxD3 */
+ 1 6 1 0 3 0 /* TxD4 */
+ 1 7 1 0 1 0 /* TxD5 */
+ 1 9 1 0 2 0 /* TxD6 */
+ 1 a 1 0 2 0 /* TxD7 */
+ 0 9 2 0 1 0 /* RxD0 */
+ 0 a 2 0 1 0 /* RxD1 */
+ 0 b 2 0 1 0 /* RxD2 */
+ 0 c 2 0 1 0 /* RxD3 */
+ 0 d 2 0 1 0 /* RxD4 */
+ 1 1 2 0 2 0 /* RxD5 */
+ 1 0 2 0 2 0 /* RxD6 */
+ 1 4 2 0 2 0 /* RxD7 */
+ 0 7 1 0 1 0 /* TX_EN */
+ 0 8 1 0 1 0 /* TX_ER */
+ 0 f 2 0 1 0 /* RX_DV */
+ 0 10 2 0 1 0 /* RX_ER */
+ 0 0 2 0 1 0 /* RX_CLK */
+ 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
+ 2 8 2 0 1 0>; /* GTX125 - CLK9 */
+ };
+
+ vii) Multi-User RAM (MURAM)
+
+ Required properties:
+ - device_type : should be "muram".
+ - mode : the could be "host" or "slave".
+ - ranges : Should be defined as specified in 1) to describe the
+ translation of MURAM addresses.
+ - data-only : sub-node which defines the address area under MURAM
+ bus that can be allocated as data/parameter
+
+ Example:
+
+ muram@10000 {
+ device_type = "muram";
+ ranges = <0 00010000 0000c000>;
+
+ data-only@0{
+ reg = <0 c000>;
+ };
+ };
More devices will be defined as this spec matures.