| Age | Commit message (Collapse) | Author |
|---|
|
commit e0429362ab15c46ea4d64c3f8c9e0933e48a143a upstream.
We've encountered a rare issue when enumerating two Logitech webcams
after a reboot that doesn't power cycle the USB ports. They are spewing
random data (possibly some leftover UVC buffers) on the second
(full-sized) Get Configuration request of the enumeration phase. Since
the data is random this can potentially cause all kinds of odd behavior,
and since it occasionally happens multiple times (after the kernel
issues another reset due to the garbled configuration descriptor), it is
not always recoverable. Set the USB_DELAY_INIT quirk that seems to work
around the issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30c219710358c5cca2f8bd2e9e547c6aadf7cf8b upstream.
There are some direct ops->enable in the regulator core driver. This is
a potential issue as the function _regulator_do_enable() handles gpio
regulators and the normal ops->enable calls. These gpio regulators are
simply ignored when ops->enable is called directly.
One possible bug is that boot-on and always-on gpio regulators are not
enabled on registration.
This patch replaces all ops->enable calls by _regulator_do_enable.
[Handle missing enable operations -- broonie]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ef7506f7eff3fc42724269f62e30164c141661f upstream.
A few of the simpler TTM drivers (cirrus, ast, mgag200) do not implement
this function. Yet can end up somehow with an evicted bo:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [< (null)>] (null)
PGD 16e761067 PUD 16e6cf067 PMD 0
Oops: 0010 [#1] SMP
Modules linked in: bnep bluetooth rfkill fuse ip6t_rpfilter ip6t_REJECT ipt_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter ip_tables sg btrfs zlib_deflate raid6_pq xor dm_queue_length iTCO_wdt iTCO_vendor_support coretemp kvm dcdbas dm_service_time microcode serio_raw pcspkr lpc_ich mfd_core i7core_edac edac_core ses enclosure ipmi_si ipmi_msghandler shpchp acpi_power_meter mperf nfsd auth_rpcgss nfs_acl lockd uinput sunrpc dm_multipath xfs libcrc32c ata_generic pata_acpi sr_mod cdrom
sd_mod usb_storage mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit lpfc drm_kms_helper ttm crc32c_intel ata_piix bfa drm ixgbe libata i2c_core mdio crc_t10dif ptp crct10dif_common pps_core scsi_transport_fc dca scsi_tgt megaraid_sas bnx2 dm_mirror dm_region_hash dm_log dm_mod
CPU: 16 PID: 2572 Comm: X Not tainted 3.10.0-86.el7.x86_64 #1
Hardware name: Dell Inc. PowerEdge R810/0H235N, BIOS 0.3.0 11/14/2009
task: ffff8801799dabc0 ti: ffff88016c884000 task.ti: ffff88016c884000
RIP: 0010:[<0000000000000000>] [< (null)>] (null)
RSP: 0018:ffff88016c885ad8 EFLAGS: 00010202
RAX: ffffffffa04e94c0 RBX: ffff880178937a20 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000240004 RDI: ffff880178937a00
RBP: ffff88016c885b60 R08: 00000000000171a0 R09: ffff88007cf171a0
R10: ffffea0005842540 R11: ffffffff810487b9 R12: ffff880178937b30
R13: ffff880178937a00 R14: ffff88016c885b78 R15: ffff880179929400
FS: 00007f81ba2ef980(0000) GS:ffff88007cf00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000016e763000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffffffffa0306fae ffff8801799295c0 0000000000260004 0000000000000001
ffff88016c885b60 ffffffffa0307669 00ff88007cf17738 ffff88017cf17700
ffff880178937a00 ffff880100000000 ffff880100000000 0000000079929400
Call Trace:
[<ffffffffa0306fae>] ? ttm_bo_handle_move_mem+0x54e/0x5b0 [ttm]
[<ffffffffa0307669>] ? ttm_bo_mem_space+0x169/0x340 [ttm]
[<ffffffffa0307bd7>] ttm_bo_move_buffer+0x117/0x130 [ttm]
[<ffffffff81130001>] ? perf_event_init_context+0x141/0x220
[<ffffffffa0307cb1>] ttm_bo_validate+0xc1/0x130 [ttm]
[<ffffffffa04e7377>] mgag200_bo_pin+0x87/0xc0 [mgag200]
[<ffffffffa04e56c4>] mga_crtc_cursor_set+0x474/0xbb0 [mgag200]
[<ffffffff811971d2>] ? __mem_cgroup_commit_charge+0x152/0x3b0
[<ffffffff815c4182>] ? mutex_lock+0x12/0x2f
[<ffffffffa0201433>] drm_mode_cursor_common+0x123/0x170 [drm]
[<ffffffffa0205231>] drm_mode_cursor_ioctl+0x41/0x50 [drm]
[<ffffffffa01f5ca2>] drm_ioctl+0x502/0x630 [drm]
[<ffffffff815cbab4>] ? __do_page_fault+0x1f4/0x510
[<ffffffff8101cb68>] ? __restore_xstate_sig+0x218/0x4f0
[<ffffffff811b4445>] do_vfs_ioctl+0x2e5/0x4d0
[<ffffffff8124488e>] ? file_has_perm+0x8e/0xa0
[<ffffffff811b46b1>] SyS_ioctl+0x81/0xa0
[<ffffffff815d05d9>] system_call_fastpath+0x16/0x1b
Code: Bad RIP value.
RIP [< (null)>] (null)
RSP <ffff88016c885ad8>
CR2: 0000000000000000
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d51246481c7f28bbfa1f814ded2da65e531cd4b2 upstream.
While preparing association request, intersection of device's
VHT capability information and corresponding field advertised
by AP is used.
This patch fixes a couple errors while saving and copying vht_cap
and vht_oper fields from AP's beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c99b1861c232e1f641f13b8645e0febb3712cc71 upstream.
While preparing association request, intersection of device's HT
capability information and corresponding fields advertised by AP
is used.
This patch fixes an error while copying this field from AP's
beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit adb07df1e039e9fe43e66aeea8b4771f83659dbb upstream.
As many Surface Pro I & II users have found out, the mwifiex_usb
doesn't support usb autosuspend, and it has caused some system
stability issues.
Bug 69661 - mwifiex_usb on MS Surface Pro 1 is unstable
Bug 60815 - Interface hangs in mwifiex_usb
Bug 64111 - mwifiex_usb USB8797 crash failed to get signal
information
USB autosuspend get triggered when Surface Pro's AC power is
removed or powertop enables power saving on USB8797 device.
Driver's suspend handler is called here, but resume handler
won't be called until the AC power is put back on or powertop
disables power saving for USB8797.
We need to refactor the suspend/resume handlers to support
usb autosuspend properly. For now let's just remove it.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c97560f6d751a620978504a4a888c631192b71a upstream.
We are sending sleep confirm done interrupt in the middle of
sleep handshake. There is a corner case when Tx done interrupt
is received from firmware during sleep handshake due to which
host and firmware power states go out of sync causing cmd and
Tx data timeout problem.
Hence sleep confirm done interrupt is sent at the end of sleep
handshake to fix the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb8e6a1ee881d131e404f0f1f5e8dc9281002771 upstream.
We may get a NULL pointer here if skb allocation for Rx packet
was failed earlier.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f7ba432202c8330cc03ab959c6228d0de5dc4a3 upstream.
Write io memory to clean PCIe buffer only when PCIe device is
present else this results into crash because of invalid memory
access.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 205e2210daa975d92ace485a65a31ccc4077fe1a upstream.
NICs supported by iwldvm don't handle well TX AMPDU.
Disable it by default, still leave the possibility to
the user to force enable it with a debug parameter.
NICs supported by iwlmvm don't suffer from the same issue,
leave TX AMPDU enabled by default for these.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 143582c6847cb285b361804c613127c25de60ca4 upstream.
Only the first packet is currently handled correctly, but then
all others are assumed to have failed which is problematic. Fix
this, marking them all successful instead (since if they're not
then the firmware will have transmitted them as single frames.)
This fixes the lost packet reporting.
Also do a tiny variable scoping cleanup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[Add the dvm part]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec6f678c74dbdb06a6a775bbb00f1d26c17c404b upstream.
We set IWL_STA_UCODE_INPROGRESS flag when we add a station
and clear it when we send the LQ command for it. But the LQ
command is sent only when the association succeeds.
If the association doesn't succeed, we would leave this flag
set and that wouldn't indicate the station entry as vacant.
This probably fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1065663
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3050248c167871ca52cfdb2ce78aa2460249346 upstream.
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d7b95315cc7f441418845a165ee56df723941487 ]
Redefine the RXD_ERR_MASK to include only relevant error bits. This fixes
a customer reported issue of randomly dropping packets on the 5719.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8f355e5cee63c2c0c145d8206c4245d0189f47ff ]
If we receive a PTP event from the NIC when we haven't set up PTP state
in the driver, we attempt to read through a NULL pointer efx->ptp_data,
triggering a panic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e7ede80d929ff0f830c44a543daa1acd590c749 ]
We should alloc big buffers also when guest can receive UFO
packets to let the big packets fit into guest rx buffer.
Fixes 5c5167515d80f78f6bb538492c423adcae31ad65
(virtio-net: Allow UFO feature to be set and advertised.)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04379dffdd4da820d51a1566ad2e86f3b1ad97ed upstream.
This patch is a modification of the patch originally proposed by
Xiaotian Feng <xtfeng@gmail.com>: https://lkml.org/lkml/2012/11/5/413
This new version disables DMA channel interrupts and ensures that the
tasklet wil not be scheduled again before calling tasklet_kill().
Unfortunately the updated patch was not released at that time due to
planned rework of Tsi721 mport driver to use threaded interrupts (which
has yet to happen). Recently the issue was reported again:
https://lkml.org/lkml/2014/2/19/762.
Description from the original Xiaotian's patch:
"Some drivers use tasklet_disable in device remove/release process,
tasklet_disable will inc tasklet->count and return. If the tasklet is
not handled yet under some softirq pressure, the tasklet will be
placed on the tasklet_vec, never have a chance to be excuted. This
might lead to a heavy loaded ksoftirqd, wakeup with pending_softirq,
but tasklet is disabled. tasklet_kill should be used in this case."
This patch is applicable to kernel versions starting from v3.5.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <bitbucket@online.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da87ca4d4ca101f177fffd84f1f0a5e4c0343557 upstream.
Since commit 77873803363c "net_dma: mark broken" we no longer pin dma
engines active for the network-receive-offload use case. As a result
the ->free_chan_resources() that occurs after the driver self test no
longer has a NET_DMA induced ->alloc_chan_resources() to back it up. A
late firing irq can lead to ksoftirqd spinning indefinitely due to the
tasklet_disable() performed by ->free_chan_resources(). Only
->alloc_chan_resources() can clear this condition in affected kernels.
This problem has been present since commit 3e037454bcfa "I/OAT: Add
support for MSI and MSI-X" in 2.6.24, but is now exposed. Given the
NET_DMA use case is deprecated we can revisit moving the driver to use
threaded irqs. For now, just tear down the irq and tasklet properly by:
1/ Disable the irq from triggering the tasklet
2/ Disable the irq from re-arming
3/ Flush inflight interrupts
4/ Flush the timer
5/ Flush inflight tasklets
References:
https://lkml.org/lkml/2014/1/27/282
https://lkml.org/lkml/2014/2/19/672
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Mike Galbraith <bitbucket@online.de>
Reported-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Tested-by: Mike Galbraith <bitbucket@online.de>
Tested-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ef4e1d000a5b335fcebfcf8aef3405e59574c89 upstream.
Causes display problems. We had already disabled
sharing for non-DP displays.
Based on a patch from:
Niels Ole Salscheider <niels_ole@salscheider-online.de>
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=58121
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e386b574cf7e1593e1296e5b0feea4108ed6ad8 upstream.
Otherwise we might get a crash here.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f050c7f9738ffa746c63415136645ad231b1348 upstream.
Print the supported functions mask in addition to
the version. This is useful in debugging PX
problems since we can see what functions are available.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1acacc0784aab45627b6009e0e9224886279ac0b upstream.
dm_pool_close_thin_device() must be called if dm_set_target_max_io_len()
fails in thin_ctr(). Otherwise __pool_destroy() will fail because the
pool will still have an open thin device:
device-mapper: thin metadata: attempt to close pmd when 1 device(s) are still open
device-mapper: thin: __pool_destroy: dm_pool_metadata_close() failed.
Also, must establish error code if failing thin_ctr() because the pool
is in fail_io mode.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d1662a30dde6e545086fe0e8fd7e474c4e0b639 upstream.
Commit 905e51b ("dm thin: commit outstanding data every second")
introduced a periodic commit. This commit occurs regardless of whether
any thin devices have made changes.
Fix the periodic commit to check if any of a pool's thin devices have
changed using dm_pool_changed_this_transaction().
Reported-by: Alexander Larsson <alexl@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1989b330093578ea5470bea0a00f940c444c466 upstream.
An invalid ioctl will never be valid, irrespective of whether multipath
has active paths or not. So for invalid ioctls we do not have to wait
for multipath to activate any paths, but can rather return an error
code immediately. This fix resolves numerous instances of:
udevd[]: worker [] unexpectedly returned with status 0x0100
that have been seen during testing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9baa9d9d520fb0e24cca671e430689de2d4a4b2 upstream.
It appears that in the DMA40 driver the DMA tasklet will very
often dereference memory for a descriptor just free:d from the
DMA40 slab. Nothing happens because no other part of the driver
has yet had a chance to claim this memory, but it's really
nasty to dereference free:d memory, so let's check the flag
before the descriptor is free and store it in a bool variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 75135da0d68419ef8a925f4c1d5f63d8046e314d upstream.
pci_get_device() decrements the reference count of "from" (last
argument) so when we break off the loop successfully we have only one
device reference - and we don't know which device we have. If we want
a reference to each device, we must take them explicitly and let
the pci_get_device() walk complete to avoid duplicate references.
This is serious, as over-putting device references will cause
the device to eventually disappear. Without this fix, the kernel
crashes after a few insmod/rmmod cycles.
Tested on an Intel S7000FC4UR system with a 7300 chipset.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224111656.09bbb7ed@endymion.delvare
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f58c780e5a5b43a6d2121e0d43cdcba1d3cc5fc upstream.
A selective retransmission request (SRR) is a fibre-channel
protocol control request which provides support for requesting
retransmission of a data sequence in response to an issue such as
frame loss or corruption. These events are experienced
infrequently in fibre-channel based networks which makes
it difficult to test and assess codepaths which handle these
events.
We were fortunate enough, for some definition of fortunate, to
have a metro-area single-mode SAN link which, at 10 GBPS
sustained load levels, would consistently generate SRR's in
a SCST based target implementation using our SCST/in-kernel
Qlogic target interface driver. In response to an SRR the
in-kernel Qlogic target driver immediately panics resulting
in a catastrophic storage failure for serviced initiators.
The culprit was a debug statement in the qla_target.c file which
does not verify that a pointer to the SCSI CDB is not null.
The unchecked pointer dereference results in the kernel panic
and resultant system failure.
The other two references to the SCSI CDB by the SRR handling code
use a ternary operator to verify a non-null pointer is being
acted on. This patch simply adds a similar test to the implicated
debug statement.
This patch is a candidate for any stable kernel being maintained
since it addresses a potentially catastrophic event with
minimal downside.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f229006ec6beabf7b844653d92fa61f025fe3dcf upstream.
Fix irq_set_affinity callbacks in the Meta IRQ chip drivers to AND
cpu_online_mask into the cpumask when picking a CPU to vector the
interrupt to.
As Thomas pointed out, the /proc/irq/$N/smp_affinity interface doesn't
filter out offline CPUs, so without this patch if you offline CPU0 and
set an IRQ affinity to 0x3 it vectors the interrupt onto CPU0 even
though it is offline.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4204960e9d0ba99459dbf1db918f99a45e7a62a upstream.
snd_soc_dapm_sync takes the dapm_mutex internally, but we currently take
it externally as well. This patch fixes this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0657716416f834ef7710a9044614d50a36c3bdc upstream.
The driver was not able to manage the sensor: during probe function
and wai check, the driver stops and writes: "device name and WhoAmI mismatch."
The correct value of L3GD20H wai is 0xd7 instead of 0xd4.
Dropped support for the sensor.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e194fd8a5d8e0a7eeed239a8534460724b62fe2d upstream.
The change (008fa749e0fe5b2fffd20b7fe4891bb80d072c6a) that moved the
node release code to a separate function broke death notifications in
some cases. When it encountered a reference without a death
notification request, it would skip looking at the remaining
references, and therefore fail to send death notifications for them.
Cc: Colin Cross <ccross@android.com>
Cc: Android Kernel Team <kernel-team@android.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 500a91571f0a5d0d3242d83802ea2fd1faccc66e upstream.
When trying to set the minimum temperature, the driver was erroneously
writing the maximum temperature into the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit accb884b32e82f943340688c9cd30290531e73e0 upstream.
In mei_cl_read_start(), if it fails to send flow control request, it
will release "cl->read_cb" but forget to set pointer to NULL, leaving
"cl->read_cb" still pointing to random memory, next time this client is
operated like mei_release(), it has chance to refer to this wrong pointer.
Fixes: PANIC at kfree in mei_release()
[228781.826904] Call Trace:
[228781.829737] [<c16249b8>] ? mei_cl_unlink+0x48/0xa0
[228781.835283] [<c1624487>] mei_io_cb_free+0x17/0x30
[228781.840733] [<c16265d8>] mei_release+0xa8/0x180
[228781.845989] [<c135c610>] ? __fsnotify_parent+0xa0/0xf0
[228781.851925] [<c1325a69>] __fput+0xd9/0x200
[228781.856696] [<c1325b9d>] ____fput+0xd/0x10
[228781.861467] [<c125cae1>] task_work_run+0x81/0xb0
[228781.866821] [<c1242e53>] do_exit+0x283/0xa00
[228781.871786] [<c1a82b36>] ? kprobe_flush_task+0x66/0xc0
[228781.877722] [<c124eeb8>] ? __dequeue_signal+0x18/0x1a0
[228781.883657] [<c124f072>] ? dequeue_signal+0x32/0x190
[228781.889397] [<c1243744>] do_group_exit+0x34/0xa0
[228781.894750] [<c12517b6>] get_signal_to_deliver+0x206/0x610
[228781.901075] [<c12018d8>] do_signal+0x38/0x100
[228781.906136] [<c1626d1c>] ? mei_read+0x42c/0x4e0
[228781.911393] [<c12600a0>] ? wake_up_bit+0x30/0x30
[228781.916745] [<c16268f0>] ? mei_poll+0x120/0x120
[228781.922001] [<c1324be9>] ? vfs_read+0x89/0x160
[228781.927158] [<c16268f0>] ? mei_poll+0x120/0x120
[228781.932414] [<c133ca34>] ? fget_light+0x44/0xe0
[228781.937670] [<c1324e58>] ? SyS_read+0x68/0x80
[228781.942730] [<c12019f5>] do_notify_resume+0x55/0x70
[228781.948376] [<c1a7de5d>] work_notifysig+0x29/0x30
[228781.953827] [<c1a70000>] ? bad_area+0x5/0x3e
Signed-off-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6dbd46c849e071e6afc1e0cad489b0175bca9318 upstream.
Hello,
the following patch adds an entry for the PID of a Cressi Leonardo
diving computer interface to kernel 3.13.0.
It is detected as FT232RL.
Works with subsurface.
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1227f3c1030e96ebc51d677d2f636268845c5fb upstream.
ehci_irq() and ehci_hrtimer_func() can deadlock on ehci->lock when
threadirqs option is used. To prevent the deadlock use
spin_lock_irqsave() in ehci_irq().
This change can be reverted when hrtimer callbacks become threaded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 12df84d4a80278a5b1abfec3206795291da52fc9 upstream.
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d1f7af3d60dd09794e0738a915d272c6c27abc5 upstream.
Commit 3dc6475 ("bcm63xx_enet: add support Broadcom BCM6345 Ethernet")
changed the ENETDMA[CS] macros such that they are no longer macros, but
actual register offset definitions. The bcm63xx_udc driver was not
updated, and as a result, causes the following build error to pop up:
CC drivers/usb/gadget/u_ether.o
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_write':
drivers/usb/gadget/bcm63xx_udc.c:642:24: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_reset_channel':
drivers/usb/gadget/bcm63xx_udc.c:698:46: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c:700:49: error: called object '0' is not
a function
Fix this by updating usb_dmac_{read,write}l and usb_dmas_{read,write}l to
take an extra channel argument, and use the channel width
(ENETDMA_CHAN_WIDTH) to offset the register we want to access, hence
doing again what the macro implicitely did for us.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bf5dbeda2454296f1984adfbfc8e6f5965ac389 upstream.
ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Michael Grzeschik <mgrzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 862474f8b46f6c1e600d4934e40ba40646c696ec upstream.
It is needed to check the number of channels returned by the HW because it
cannot be greater than MAX_NET_DEVICES otherwise it will crash.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3ca4164529b875374c410193bbbac0ee960895f upstream.
acpi_processor_set_throttling() uses set_cpus_allowed_ptr() to make
sure that the (struct acpi_processor)->acpi_processor_set_throttling()
callback will run on the right CPU. However, the function may be
called from a worker thread already bound to a different CPU in which
case that won't work.
Make acpi_processor_set_throttling() use work_on_cpu() as appropriate
instead of abusing set_cpus_allowed_ptr().
Reported-and-tested-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd8ba20597f0cfef3ef65c3fd2aa92ab23d4c8e1 upstream.
Some devices have duplicate entries in there brightness levels table, ie
on my Dell Latitude E6430 the table looks like this:
[ 3.686060] acpi backlight index 0, val 80
[ 3.686095] acpi backlight index 1, val 50
[ 3.686122] acpi backlight index 2, val 5
[ 3.686147] acpi backlight index 3, val 5
[ 3.686172] acpi backlight index 4, val 5
[ 3.686197] acpi backlight index 5, val 5
[ 3.686223] acpi backlight index 6, val 5
[ 3.686248] acpi backlight index 7, val 5
[ 3.686273] acpi backlight index 8, val 6
[ 3.686332] acpi backlight index 9, val 7
[ 3.686356] acpi backlight index 10, val 8
[ 3.686380] acpi backlight index 11, val 9
etc.
Notice that brightness values 0-5 are all mapped to 5. This means that
if userspace writes any value between 0 and 5 to the brightness sysfs attribute
and then reads it, it will always return 0, which is somewhat unexpected.
This is a problem for ie gnome-settings-daemon, which uses read-modify-write
logic when the users presses the brightness up or down keys. This is done
this way to take brightness changes from other sources into account.
On this specific laptop what happens once the brightness has been set to 0,
is that gsd reads 0, adds 5, writes 5, and on the next brightness up key press
again reads 0, so things get stuck at the lowest brightness setting.
Filtering out the duplicate table entries, makes any write to brightness
read back as the written value as one would expect, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c0f5eeed0f4cef4f05b74883a7160e7edde58b6a upstream.
The reference count changes done by pci_get_device can be a little
misleading when the usage diverges from the most common scheme. The
reference count of the device passed as the last parameter is always
decreased, even if the function returns no new device. So if we are
going to try alternative device IDs, we must manually increment the
device reference count before each retry. If we don't, we end up
decreasing the reference count, and after a few modprobe/rmmod cycles
the PCI devices will vanish.
In other words and as Alan put it: without this fix the EDAC code
corrupts the PCI device list.
This fixes kernel bug #50491:
https://bugzilla.kernel.org/show_bug.cgi?id=50491
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224093927.7659dd9d@endymion.delvare
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b685f3b1744061aa9ad822548ba9c674de5be7c6 upstream.
acpi_pci_link_allocate_irq() can return negative gsi even if
entry != NULL. For that case we have a memory leak, so free
entry before returning from acpi_pci_irq_enable() for gsi < 0.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f42db786b14a31bf807fc41ee5583a00c08fcb1 upstream.
Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts. Clear Interrupt Disable so we get those interrupts.
Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.
Link: http://lkml.kernel.org/r/20140114181721.GC12126@xanatos
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70601
Reported-by: Chris Cheng <chris.cheng@atrustcorp.com>
Reported-and-tested-by: Jamie Chen <jamie.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3274763bfc3bf1ececa269ed6e6c4d7ec1c3e5e upstream.
The powernow-k8 driver maintains a per-cpu data-structure called
powernow_data that is used to perform the frequency transitions.
It initializes this data structure only for the policy->cpu. So,
accesses to this data structure by other CPUs results in various
problems because they would have been uninitialized.
Specifically, if a cpu (!= policy->cpu) invokes the drivers' ->get()
function, it returns 0 as the KHz value, since its per-cpu memory
doesn't point to anything valid. This causes problems during
suspend/resume since cpufreq_update_policy() tries to enforce this
(0 KHz) as the current frequency of the CPU, and this madness gets
propagated to adjust_jiffies() as well. Eventually, lots of things
start breaking down, including the r8169 ethernet card, in one
particularly interesting case reported by Pierre Ossman.
Fix this by initializing the per-cpu data-structures of all the CPUs
in the policy appropriately.
References: https://bugzilla.kernel.org/show_bug.cgi?id=70311
Reported-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f9c47f00ce99329b1a82e2ac4f70f0fe3db549c upstream.
It's a bit odd to see a newer device showing mod15write; however, the
reported behavior is highly consistent and other factors which could
contribute seem to have been verified well enough. Also, both
sata_sil itself and the drive are fairly outdated at this point making
the risk of this change fairly low. It is possible, probably likely,
that other drive models in the same family have the same problem;
however, for now, let's just add the specific model which was tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: matson <lists-matsonpa@luxsci.me>
References: http://lkml.kernel.org/g/201401211912.s0LJCk7F015058@rs103.luxsci.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efb9e0f4f43780f0ae0c6428d66bd03e805c7539 upstream.
Without the patch the kernel generates the following error.
ata11.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata11.15: Port Multiplier vendor mismatch '0x197b' != '0x123'
ata11.15: PMP revalidation failed (errno=-19)
ata11.15: failed to recover PMP after 5 tries, giving up
This patch helps to bypass this error and the device becomes
functional.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: <linux-ide@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67809f85d31eac600f6b28defa5386c9d2a13b1d upstream.
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 163c8ff30dbe473abfbb24a7eac5536c87f3baa9 ]
aggregator_identifier is used to assign unique aggregator identifiers
to aggregators of a bond during device enslaving.
aggregator_identifier is currently a global variable that is zeroed in
bond_3ad_initialize().
This sequence will lead to duplicate aggregator identifiers for eth1 and eth3:
create bond0
change bond0 mode to 802.3ad
enslave eth0 to bond0 //eth0 gets agg id 1
enslave eth1 to bond0 //eth1 gets agg id 2
create bond1
change bond1 mode to 802.3ad
enslave eth2 to bond1 //aggregator_identifier is reset to 0
//eth2 gets agg id 1
enslave eth3 to bond0 //eth3 gets agg id 2
Fix this by making aggregator_identifier private to the bond.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit eb85569fe2d06c2fbf4de7b66c263ca095b397aa ]
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
