| Age | Commit message (Collapse) | Author |
|---|
|
This is the 3.10.23 stable release
|
|
commit eb1c160b22655fd4ec44be732d6594fd1b1e44f4 upstream.
The soft lockup below happens at the boot time of the system using dm
multipath and the udev rules to switch scheduler.
[ 356.127001] BUG: soft lockup - CPU#3 stuck for 22s! [sh:483]
[ 356.127001] RIP: 0010:[<ffffffff81072a7d>] [<ffffffff81072a7d>] lock_timer_base.isra.35+0x1d/0x50
...
[ 356.127001] Call Trace:
[ 356.127001] [<ffffffff81073810>] try_to_del_timer_sync+0x20/0x70
[ 356.127001] [<ffffffff8118b08a>] ? kmem_cache_alloc_node_trace+0x20a/0x230
[ 356.127001] [<ffffffff810738b2>] del_timer_sync+0x52/0x60
[ 356.127001] [<ffffffff812ece22>] cfq_exit_queue+0x32/0xf0
[ 356.127001] [<ffffffff812c98df>] elevator_exit+0x2f/0x50
[ 356.127001] [<ffffffff812c9f21>] elevator_change+0xf1/0x1c0
[ 356.127001] [<ffffffff812caa50>] elv_iosched_store+0x20/0x50
[ 356.127001] [<ffffffff812d1d09>] queue_attr_store+0x59/0xb0
[ 356.127001] [<ffffffff812143f6>] sysfs_write_file+0xc6/0x140
[ 356.127001] [<ffffffff811a326d>] vfs_write+0xbd/0x1e0
[ 356.127001] [<ffffffff811a3ca9>] SyS_write+0x49/0xa0
[ 356.127001] [<ffffffff8164e899>] system_call_fastpath+0x16/0x1b
This is caused by a race between md device initialization by multipathd and
shell script to switch the scheduler using sysfs.
- multipathd:
SyS_ioctl -> do_vfs_ioctl -> dm_ctl_ioctl -> ctl_ioctl -> table_load
-> dm_setup_md_queue -> blk_init_allocated_queue -> elevator_init
q->elevator = elevator_alloc(q, e); // not yet initialized
- sh -c 'echo deadline > /sys/$DEVPATH/queue/scheduler':
elevator_switch (in the call trace above)
struct elevator_queue *old = q->elevator;
q->elevator = elevator_alloc(q, new_e);
elevator_exit(old); // lockup! (*)
- multipathd: (cont.)
err = e->ops.elevator_init_fn(q); // init fails; q->elevator is modified
(*) When del_timer_sync() is called, lock_timer_base() will loop infinitely
while timer->base == NULL. In this case, as timer will never initialized,
it results in lockup.
This patch introduces acquisition of q->sysfs_lock around elevator_init()
into blk_init_allocated_queue(), to provide mutual exclusion between
initialization of the q->scheduler and switching of the scheduler.
This should fix this bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=902012
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 3.10.22 stable release
|
|
commit fff4996b7db7955414ac74386efa5e07fd766b50 upstream.
If blkcg_init_queue fails, blk_alloc_queue_node doesn't call bdi_destroy
to clean up structures allocated by the backing dev.
------------[ cut here ]------------
WARNING: at lib/debugobjects.c:260 debug_print_object+0x85/0xa0()
ODEBUG: free active (active state 0) object type: percpu_counter hint: (null)
Modules linked in: dm_loop dm_mod ip6table_filter ip6_tables uvesafb cfbcopyarea cfbimgblt cfbfillrect fbcon font bitblit fbcon_rotate fbcon_cw fbcon_ud fbcon_ccw softcursor fb fbdev ipt_MASQUERADE iptable_nat nf_nat_ipv4 msr nf_conntrack_ipv4 nf_defrag_ipv4 xt_state ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp llc tun ipv6 cpufreq_userspace cpufreq_stats cpufreq_powersave cpufreq_ondemand cpufreq_conservative spadfs fuse hid_generic usbhid hid raid0 md_mod dmi_sysfs nf_nat_ftp nf_nat nf_conntrack_ftp nf_conntrack lm85 hwmon_vid snd_usb_audio snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc snd_hwdep snd_usbmidi_lib snd_rawmidi snd soundcore acpi_cpufreq freq_table mperf sata_svw serverworks kvm_amd ide_core ehci_pci ohci_hcd libata ehci_hcd kvm usbcore tg3 usb_common libphy k10temp pcspkr ptp i2c_piix4 i2c_core evdev microcode hwmon rtc_cmos pps_core e100 skge floppy mii processor button unix
CPU: 0 PID: 2739 Comm: lvchange Tainted: G W
3.10.15-devel #14
Hardware name: empty empty/S3992-E, BIOS 'V1.06 ' 06/09/2009
0000000000000009 ffff88023c3c1ae8 ffffffff813c8fd4 ffff88023c3c1b20
ffffffff810399eb ffff88043d35cd58 ffffffff81651940 ffff88023c3c1bf8
ffffffff82479d90 0000000000000005 ffff88023c3c1b80 ffffffff81039a67
Call Trace:
[<ffffffff813c8fd4>] dump_stack+0x19/0x1b
[<ffffffff810399eb>] warn_slowpath_common+0x6b/0xa0
[<ffffffff81039a67>] warn_slowpath_fmt+0x47/0x50
[<ffffffff8122aaaf>] ? debug_check_no_obj_freed+0xcf/0x250
[<ffffffff81229a15>] debug_print_object+0x85/0xa0
[<ffffffff8122abe3>] debug_check_no_obj_freed+0x203/0x250
[<ffffffff8113c4ac>] kmem_cache_free+0x20c/0x3a0
[<ffffffff811f6709>] blk_alloc_queue_node+0x2a9/0x2c0
[<ffffffff811f672e>] blk_alloc_queue+0xe/0x10
[<ffffffffa04c0093>] dm_create+0x1a3/0x530 [dm_mod]
[<ffffffffa04c6bb0>] ? list_version_get_info+0xe0/0xe0 [dm_mod]
[<ffffffffa04c6c07>] dev_create+0x57/0x2b0 [dm_mod]
[<ffffffffa04c6bb0>] ? list_version_get_info+0xe0/0xe0 [dm_mod]
[<ffffffffa04c6bb0>] ? list_version_get_info+0xe0/0xe0 [dm_mod]
[<ffffffffa04c6528>] ctl_ioctl+0x268/0x500 [dm_mod]
[<ffffffff81097662>] ? get_lock_stats+0x22/0x70
[<ffffffffa04c67ce>] dm_ctl_ioctl+0xe/0x20 [dm_mod]
[<ffffffff81161aad>] do_vfs_ioctl+0x2ed/0x520
[<ffffffff8116cfc7>] ? fget_light+0x377/0x4e0
[<ffffffff81161d2b>] SyS_ioctl+0x4b/0x90
[<ffffffff813cff16>] system_call_fastpath+0x1a/0x1f
---[ end trace 4b5ff0d55673d986 ]---
------------[ cut here ]------------
This fix should be backported to stable kernels starting with 2.6.37. Note
that in the kernels prior to 3.5 the affected code is different, but the
bug is still there - bdi_init is called and bdi_destroy isn't.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 3.10.21 stable release
|
|
commit 4912aa6c11e6a5d910264deedbec2075c6f1bb73 upstream.
crocode i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma dca be2net sg ses enclosure ext4 mbcache jbd2 sd_mod crc_t10dif ahci megaraid_sas(U) dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan]
Pid: 491, comm: scsi_eh_0 Tainted: G W ---------------- 2.6.32-220.13.1.el6.x86_64 #1 IBM -[8722PAX]-/00D1461
RIP: 0010:[<ffffffff8124e424>] [<ffffffff8124e424>] blk_requeue_request+0x94/0xa0
RSP: 0018:ffff881057eefd60 EFLAGS: 00010012
RAX: ffff881d99e3e8a8 RBX: ffff881d99e3e780 RCX: ffff881d99e3e8a8
RDX: ffff881d99e3e8a8 RSI: ffff881d99e3e780 RDI: ffff881d99e3e780
RBP: ffff881057eefd80 R08: ffff881057eefe90 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff881057f92338
R13: 0000000000000000 R14: ffff881057f92338 R15: ffff883058188000
FS: 0000000000000000(0000) GS:ffff880040200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000000006d3ec0 CR3: 000000302cd7d000 CR4: 00000000000406b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process scsi_eh_0 (pid: 491, threadinfo ffff881057eee000, task ffff881057e29540)
Stack:
0000000000001057 0000000000000286 ffff8810275efdc0 ffff881057f16000
<0> ffff881057eefdd0 ffffffff81362323 ffff881057eefe20 ffffffff8135f393
<0> ffff881057e29af8 ffff8810275efdc0 ffff881057eefe78 ffff881057eefe90
Call Trace:
[<ffffffff81362323>] __scsi_queue_insert+0xa3/0x150
[<ffffffff8135f393>] ? scsi_eh_ready_devs+0x5e3/0x850
[<ffffffff81362a23>] scsi_queue_insert+0x13/0x20
[<ffffffff8135e4d4>] scsi_eh_flush_done_q+0x104/0x160
[<ffffffff8135fb6b>] scsi_error_handler+0x35b/0x660
[<ffffffff8135f810>] ? scsi_error_handler+0x0/0x660
[<ffffffff810908c6>] kthread+0x96/0xa0
[<ffffffff8100c14a>] child_rip+0xa/0x20
[<ffffffff81090830>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20
Code: 00 00 eb d1 4c 8b 2d 3c 8f 97 00 4d 85 ed 74 bf 49 8b 45 00 49 83 c5 08 48 89 de 4c 89 e7 ff d0 49 8b 45 00 48 85 c0 75 eb eb a4 <0f> 0b eb fe 0f 1f 84 00 00 00 00 00 55 48 89 e5 0f 1f 44 00 00
RIP [<ffffffff8124e424>] blk_requeue_request+0x94/0xa0
RSP <ffff881057eefd60>
The RIP is this line:
BUG_ON(blk_queued_rq(rq));
After digging through the code, I think there may be a race between the
request completion and the timer handler running.
A timer is started for each request put on the device's queue (see
blk_start_request->blk_add_timer). If the request does not complete
before the timer expires, the timer handler (blk_rq_timed_out_timer)
will mark the request complete atomically:
static inline int blk_mark_rq_complete(struct request *rq)
{
return test_and_set_bit(REQ_ATOM_COMPLETE, &rq->atomic_flags);
}
and then call blk_rq_timed_out. The latter function will call
scsi_times_out, which will return one of BLK_EH_HANDLED,
BLK_EH_RESET_TIMER or BLK_EH_NOT_HANDLED. If BLK_EH_RESET_TIMER is
returned, blk_clear_rq_complete is called, and blk_add_timer is again
called to simply wait longer for the request to complete.
Now, if the request happens to complete while this is going on, what
happens? Given that we know the completion handler will bail if it
finds the REQ_ATOM_COMPLETE bit set, we need to focus on the completion
handler running after that bit is cleared. So, from the above
paragraph, after the call to blk_clear_rq_complete. If the completion
sets REQ_ATOM_COMPLETE before the BUG_ON in blk_add_timer, we go boom
there (I haven't seen this in the cores). Next, if we get the
completion before the call to list_add_tail, then the timer will
eventually fire for an old req, which may either be freed or reallocated
(there is evidence that this might be the case). Finally, if the
completion comes in *after* the addition to the timeout list, I think
it's harmless. The request will be removed from the timeout list,
req_atom_complete will be set, and all will be well.
This will only actually explain the coredumps *IF* the request
structure was freed, reallocated *and* queued before the error handler
thread had a chance to process it. That is possible, but it may make
sense to keep digging for another race. I think that if this is what
was happening, we would see other instances of this problem showing up
as null pointer or garbage pointer dereferences, for example when the
request structure was not re-used. It looks like we actually do run
into that situation in other reports.
This patch moves the BUG_ON(test_bit(REQ_ATOM_COMPLETE,
&req->atomic_flags)); from blk_add_timer to the only caller that could
trip over it (blk_start_request). It then inverts the calls to
blk_clear_rq_complete and blk_add_timer in blk_rq_timed_out to address
the race. I've boot tested this patch, but nothing more.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Block layer uses workqueues for multiple purposes. There is no real dependency
of scheduling these on the cpu which scheduled them.
On a idle system, it is observed that and idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.
This patch replaces normal workqueues with power efficient versions.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
(cherry picked from commit 695588f9454bdbc7c1a2fbb8a6bfdcfba6183348)
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
In blk_post_runtime_resume, an autosuspend request will be initiated for
the device. Since we are holding the queue lock, we can't sleep and thus
we should use the async version to initiate an autosuspend, i.e.
pm_request_suspend instead of pm_runtime_suspend, which might sleep.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
|
|
This reverts commit 3a366e614d0837d9fc23f78cdb1a1186ebc3387f.
Wanlong Gao reports that it causes a kernel panic on his machine several
minutes after boot. Reverting it removes the panic.
Jens says:
"It's not quite clear why that is yet, so I think we should just revert
the commit for 3.9 final (which I'm assuming is pretty close).
The wifi is crap at the LSF hotel, so sending this email instead of
queueing up a revert and pull request."
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Requested-by: Jens Axboe <axboe@kernel.dk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
for-3.10/core
This contains Kents prep work for the immutable bio_vecs.
|
|
Just a little convenience macro - main reason to add it now is preparing
for immutable bio vecs, it'll reduce the size of the patch that puts
bi_sector/bi_size/bi_idx into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux-s390@vger.kernel.org
CC: Chris Mason <chris.mason@fusionio.com>
CC: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Converts it to use bio_advance(), simplifying it quite a bit in the
process.
Note that req_bio_endio() now always calls bio_advance() - which means
it always loops over the biovec, not just on partial completions. Don't
expect it to affect performance, but worth noting.
Tested it by forcing partial updates, and dumping before and after on
various bio/bvec fields when doing a partial update.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
|
|
When a request is added:
If device is suspended or is suspending and the request is not a
PM request, resume the device.
When the last request finishes:
Call pm_runtime_mark_last_busy().
When pick a request:
If device is resuming/suspending, then only PM request is allowed
to go.
The idea and API is designed by Alan Stern and described here:
http://marc.info/?l=linux-scsi&m=133727953625963&w=2
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add runtime pm helper functions:
void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
- Initialization function for drivers to call.
int blk_pre_runtime_suspend(struct request_queue *q)
- If any requests are in the queue, mark last busy and return -EBUSY.
Otherwise set q->rpm_status to RPM_SUSPENDING and return 0.
void blk_post_runtime_suspend(struct request_queue *q, int err)
- If the suspend succeeded then set q->rpm_status to RPM_SUSPENDED.
Otherwise set it to RPM_ACTIVE and mark last busy.
void blk_pre_runtime_resume(struct request_queue *q)
- Set q->rpm_status to RPM_RESUMING.
void blk_post_runtime_resume(struct request_queue *q, int err)
- If the resume succeeded then set q->rpm_status to RPM_ACTIVE
and call __blk_run_queue, then mark last busy and autosuspend.
Otherwise set q->rpm_status to RPM_SUSPENDED.
The idea and API is designed by Alan Stern and described here:
http://marc.info/?l=linux-scsi&m=133727953625963&w=2
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block IO core bits from Jens Axboe:
"Below are the core block IO bits for 3.9. It was delayed a few days
since my workstation kept crashing every 2-8h after pulling it into
current -git, but turns out it is a bug in the new pstate code (divide
by zero, will report separately). In any case, it contains:
- The big cfq/blkcg update from Tejun and and Vivek.
- Additional block and writeback tracepoints from Tejun.
- Improvement of the should sort (based on queues) logic in the plug
flushing.
- _io() variants of the wait_for_completion() interface, using
io_schedule() instead of schedule() to contribute to io wait
properly.
- Various little fixes.
You'll get two trivial merge conflicts, which should be easy enough to
fix up"
Fix up the trivial conflicts due to hlist traversal cleanups (commit
b67bfe0d42ca: "hlist: drop the node parameter from iterators").
* 'for-3.9/core' of git://git.kernel.dk/linux-block: (39 commits)
block: remove redundant check to bd_openers()
block: use i_size_write() in bd_set_size()
cfq: fix lock imbalance with failed allocations
drivers/block/swim3.c: fix null pointer dereference
block: don't select PERCPU_RWSEM
block: account iowait time when waiting for completion of IO request
sched: add wait_for_completion_io[_timeout]
writeback: add more tracepoints
block: add block_{touch|dirty}_buffer tracepoint
buffer: make touch_buffer() an exported function
block: add @req to bio_{front|back}_merge tracepoints
block: add missing block_bio_complete() tracepoint
block: Remove should_sort judgement when flush blk_plug
block,elevator: use new hashtable implementation
cfq-iosched: add hierarchical cfq_group statistics
cfq-iosched: collect stats from dead cfqgs
cfq-iosched: separate out cfqg_stats_reset() from cfq_pd_reset_stats()
blkcg: make blkcg_print_blkgs() grab q locks instead of blkcg lock
block: RCU free request_queue
blkcg: implement blkg_[rw]stat_recursive_sum() and blkg_[rw]stat_merge()
...
|
|
This provides a band-aid to provide stable page writes on jbd without
needing to backport the fixed locking and page writeback bit handling
schemes of jbd2. The band-aid works by using bounce buffers to snapshot
page contents instead of waiting.
For those wondering about the ext3 bandage -- fixing the jbd locking
(which was done as part of ext4dev years ago) is a lot of surgery, and
setting PG_writeback on data pages when we actually hold the page lock
dropped ext3 performance by nearly an order of magnitude. If we're
going to migrate iscsi and raid to use stable page writes, the
complaints about high latency will likely return. We might as well
centralize their page snapshotting thing to one place.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
bio_{front|back}_merge tracepoints report a bio merging into an
existing request but didn't specify which request the bio is being
merged into. Add @req to it. This makes it impossible to share the
event template with block_bio_queue - split it out.
@req isn't used or exported to userland at this point and there is no
userland visible behavior change. Later changes will make use of the
extra parameter.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
bio completion didn't kick block_bio_complete TP. Only dm was
explicitly triggering the TP on IO completion. This makes
block_bio_complete TP useless for tracers which want to know about
bios, and all other bio based drivers skip generating blktrace
completion events.
This patch makes all bio completions via bio_endio() generate
block_bio_complete TP.
* Explicit trace_block_bio_complete() invocation removed from dm and
the trace point is unexported.
* @rq dropped from trace_block_bio_complete(). bios may fly around
w/o queue associated. Verifying and accessing the assocaited queue
belongs to TP probes.
* blktrace now gets both request and bio completions. Make it ignore
bio completions if request completion path is happening.
This makes all bio based drivers generate blktrace completion events
properly and makes the block_bio_complete TP actually useful.
v2: With this change, block_bio_complete TP could be invoked on sg
commands which have bio's with %NULL bi_bdev. Update TP
assignment code to check whether bio->bi_bdev is %NULL before
dereferencing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Original-patch-by: Namhyung Kim <namhyung@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In commit 975927b942c932,it add blk_rq_pos to sort rq when flushing.
Although this commit was used for the situation which blk_plug handled
multi devices on the same time like md device.
I think there must be some situations like this but only single
device.
So remove the should_sort judgement.
Because the parameter should_sort is only for this purpose,it can delete
should_sort from blk_plug.
CC: Shaohua Li <shli@kernel.org>
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This allows stacked devices (like md/raid5) to provide blktrace
tracing, including unplug events.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some request_fn implementations, e.g. scsi_request_fn(), unlock
the queue lock internally. This may result in multiple threads
executing request_fn for the same queue simultaneously. Keep
track of the number of active request_fn calls and make sure that
blk_cleanup_queue() waits until all active request_fn invocations
have finished. A block driver may start cleaning up resources
needed by its request_fn as soon as blk_cleanup_queue() finished,
so blk_cleanup_queue() must wait for all outstanding request_fn
invocations to finish.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Chanho Min <chanho.min@lge.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Running a queue must continue after it has been marked dying until
it has been marked dead. So the function blk_run_queue_async() must
not schedule delayed work after blk_cleanup_queue() has marked a queue
dead. Hence add a test for that queue state in blk_run_queue_async()
and make sure that queue_unplugged() invokes that function with the
queue lock held. This avoids that the queue state can change after
it has been tested and before mod_delayed_work() is invoked. Drop
the queue dying test in queue_unplugged() since it is now
superfluous: __blk_run_queue() already tests whether or not the
queue is dead.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A block driver may start cleaning up resources needed by its
request_fn as soon as blk_cleanup_queue() finished, so request_fn
must not be invoked after draining finished. This is important
when blk_run_queue() is invoked without any requests in progress.
As an example, if blk_drain_queue() and scsi_run_queue() run in
parallel, blk_drain_queue() may have finished all requests after
scsi_run_queue() has taken a SCSI device off the starved list but
before that last function has had a chance to run the queue.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Chanho Min <chanho.min@lge.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Let the caller of blk_drain_queue() obtain the queue lock to improve
readability of the patch called "Avoid that request_fn is invoked on
a dead queue".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
QUEUE_FLAG_DEAD is used to indicate that queuing new requests must
stop. After this flag has been set queue draining starts. However,
during the queue draining phase it is still safe to invoke the
queue's request_fn, so QUEUE_FLAG_DYING is a better name for this
flag.
This patch has been generated by running the following command
over the kernel source tree:
git grep -lEw 'blk_queue_dead|QUEUE_FLAG_DEAD' |
xargs sed -i.tmp -e 's/blk_queue_dead/blk_queue_dying/g' \
-e 's/QUEUE_FLAG_DEAD/QUEUE_FLAG_DYING/g'; \
sed -i.tmp -e "s/QUEUE_FLAG_DYING$(printf \\t)*5/QUEUE_FLAG_DYING$(printf \\t)5/g" \
include/linux/blkdev.h; \
sed -i.tmp -e 's/ DEAD/ DYING/g' -e 's/dead queue/a dying queue/' \
-e 's/Dead queue/A dying queue/' block/blk-core.c
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Modified by me to cover blk_init_queue() as well.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
My workload is a raid5 which had 16 disks. And used our filesystem to
write using direct-io mode.
I used the blktrace to find those message:
8,16 0 6647 2.453665504 2579 M W 7493152 + 8 [md0_raid5]
8,16 0 6648 2.453672411 2579 Q W 7493160 + 8 [md0_raid5]
8,16 0 6649 2.453672606 2579 M W 7493160 + 8 [md0_raid5]
8,16 0 6650 2.453679255 2579 Q W 7493168 + 8 [md0_raid5]
8,16 0 6651 2.453679441 2579 M W 7493168 + 8 [md0_raid5]
8,16 0 6652 2.453685948 2579 Q W 7493176 + 8 [md0_raid5]
8,16 0 6653 2.453686149 2579 M W 7493176 + 8 [md0_raid5]
8,16 0 6654 2.453693074 2579 Q W 7493184 + 8 [md0_raid5]
8,16 0 6655 2.453693254 2579 M W 7493184 + 8 [md0_raid5]
8,16 0 6656 2.453704290 2579 Q W 7493192 + 8 [md0_raid5]
8,16 0 6657 2.453704482 2579 M W 7493192 + 8 [md0_raid5]
8,16 0 6658 2.453715016 2579 Q W 7493200 + 8 [md0_raid5]
8,16 0 6659 2.453715247 2579 M W 7493200 + 8 [md0_raid5]
8,16 0 6660 2.453721730 2579 Q W 7493208 + 8 [md0_raid5]
8,16 0 6661 2.453721974 2579 M W 7493208 + 8 [md0_raid5]
8,16 0 6662 2.453728202 2579 Q W 7493216 + 8 [md0_raid5]
8,16 0 6663 2.453728436 2579 M W 7493216 + 8 [md0_raid5]
8,16 0 6664 2.453734782 2579 Q W 7493224 + 8 [md0_raid5]
8,16 0 6665 2.453735019 2579 M W 7493224 + 8 [md0_raid5]
8,16 0 6666 2.453741401 2579 Q W 7493232 + 8 [md0_raid5]
8,16 0 6667 2.453741632 2579 M W 7493232 + 8 [md0_raid5]
8,16 0 6668 2.453748148 2579 Q W 7493240 + 8 [md0_raid5]
8,16 0 6669 2.453748386 2579 M W 7493240 + 8 [md0_raid5]
8,16 0 6670 2.453851843 2579 I W 7493144 + 104 [md0_raid5]
8,16 0 0 2.453853661 0 m N cfq2579 insert_request
8,16 0 6671 2.453854064 2579 I W 7493120 + 24 [md0_raid5]
8,16 0 0 2.453854439 0 m N cfq2579 insert_request
8,16 0 6672 2.453854793 2579 U N [md0_raid5] 2
8,16 0 0 2.453855513 0 m N cfq2579 Not idling.st->count:1
8,16 0 0 2.453855927 0 m N cfq2579 dispatch_insert
8,16 0 0 2.453861771 0 m N cfq2579 dispatched a request
8,16 0 0 2.453862248 0 m N cfq2579 activate rq,drv=1
8,16 0 6673 2.453862332 2579 D W 7493120 + 24 [md0_raid5]
8,16 0 0 2.453865957 0 m N cfq2579 Not idling.st->count:1
8,16 0 0 2.453866269 0 m N cfq2579 dispatch_insert
8,16 0 0 2.453866707 0 m N cfq2579 dispatched a request
8,16 0 0 2.453867061 0 m N cfq2579 activate rq,drv=2
8,16 0 6674 2.453867145 2579 D W 7493144 + 104 [md0_raid5]
8,16 0 6675 2.454147608 0 C W 7493120 + 24 [0]
8,16 0 0 2.454149357 0 m N cfq2579 complete rqnoidle 0
8,16 0 6676 2.454791505 0 C W 7493144 + 104 [0]
8,16 0 0 2.454794803 0 m N cfq2579 complete rqnoidle 0
8,16 0 0 2.454795160 0 m N cfq schedule dispatch
From above messages,we can find rq[W 7493144 + 104] and rq[W
7493120 + 24] do not merge.
Because the bio order is:
8,16 0 6638 2.453619407 2579 Q W 7493144 + 8 [md0_raid5]
8,16 0 6639 2.453620460 2579 G W 7493144 + 8 [md0_raid5]
8,16 0 6640 2.453639311 2579 Q W 7493120 + 8 [md0_raid5]
8,16 0 6641 2.453639842 2579 G W 7493120 + 8 [md0_raid5]
The bio(7493144) first and bio(7493120) later.So the subsequent
bios will be divided into two parts.
When flushing plug-list,because elv_attempt_insert_merge only support
backmerge,not supporting frontmerge.
So rq[7493120 + 24] can't merge with rq[7493144 + 104].
From my test,i found those situation can count 25% in our system.
Using this patch, there is no this situation.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
CC:Shaohua Li <shli@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block IO update from Jens Axboe:
"Core block IO bits for 3.7. Not a huge round this time, it contains:
- First series from Kent cleaning up and generalizing bio allocation
and freeing.
- WRITE_SAME support from Martin.
- Mikulas patches to prevent O_DIRECT crashes when someone changes
the block size of a device.
- Make bio_split() work on data-less bio's (like trim/discards).
- A few other minor fixups."
Fixed up silent semantic mis-merge as per Mikulas Patocka and Andrew
Morton. It is due to the VM no longer using a prio-tree (see commit
6b2dbba8b6ac: "mm: replace vma prio_tree with an interval tree").
So make set_blocksize() use mapping_mapped() instead of open-coding the
internal VM knowledge that has changed.
* 'for-3.7/core' of git://git.kernel.dk/linux-block: (26 commits)
block: makes bio_split support bio without data
scatterlist: refactor the sg_nents
scatterlist: add sg_nents
fs: fix include/percpu-rwsem.h export error
percpu-rw-semaphore: fix documentation typos
fs/block_dev.c:1644:5: sparse: symbol 'blkdev_mmap' was not declared
blockdev: turn a rw semaphore into a percpu rw semaphore
Fix a crash when block device is read and block size is changed at the same time
block: fix request_queue->flags initialization
block: lift the initial queue bypass mode on blk_register_queue() instead of blk_init_allocated_queue()
block: ioctl to zero block ranges
block: Make blkdev_issue_zeroout use WRITE SAME
block: Implement support for WRITE SAME
block: Consolidate command flag and queue limit checks for merges
block: Clean up special command handling logic
block/blk-tag.c: Remove useless kfree
block: remove the duplicated setting for congestion_threshold
block: reject invalid queue attribute values
block: Add bio_clone_bioset(), bio_clone_kmalloc()
block: Consolidate bio_alloc_bioset(), bio_kmalloc()
...
|
|
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
|
|
A queue newly allocated with blk_alloc_queue_node() has only
QUEUE_FLAG_BYPASS set. For request-based drivers,
blk_init_allocated_queue() is called and q->queue_flags is overwritten
with QUEUE_FLAG_DEFAULT which doesn't include BYPASS even though the
initial bypass is still in effect.
In blk_init_allocated_queue(), or QUEUE_FLAG_DEFAULT to q->queue_flags
instead of overwriting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
blk_init_allocated_queue()
b82d4b197c ("blkcg: make request_queue bypassing on allocation") made
request_queues bypassed on allocation to avoid switching on and off
bypass mode on a queue being initialized. Some drivers allocate and
then destroy a lot of queues without fully initializing them and
incurring bypass latency overhead on each of them could add upto
significant overhead.
Unfortunately, blk_init_allocated_queue() is never used by queues of
bio-based drivers, which means that all bio-based driver queues are in
bypass mode even after initialization and registration complete
successfully.
Due to the limited way request_queues are used by bio drivers, this
problem is hidden pretty well but it shows up when blk-throttle is
used in combination with a bio-based driver. Trying to configure
(echoing to cgroupfs file) blk-throttle for a bio-based driver hangs
indefinitely in blkg_conf_prep() waiting for bypass mode to end.
This patch moves the initial blk_queue_bypass_end() call from
blk_init_allocated_queue() to blk_register_queue() which is called for
any userland-visible queues regardless of its type.
I believe this is correct because I don't think there is any block
driver which needs or wants working elevator and blk-cgroup on a queue
which isn't visible to userland. If there are such users, we need a
different solution.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Joseph Glanville <joseph.glanville@orionvm.com.au>
Cc: stable@vger.kernel.org
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The WRITE SAME command supported on some SCSI devices allows the same
block to be efficiently replicated throughout a block range. Only a
single logical block is transferred from the host and the storage device
writes the same data to all blocks described by the I/O.
This patch implements support for WRITE SAME in the block layer. The
blkdev_issue_write_same() function can be used by filesystems and block
drivers to replicate a buffer across a block range. This can be used to
efficiently initialize software RAID devices, etc.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
- blk_check_merge_flags() verifies that cmd_flags / bi_rw are
compatible. This function is called for both req-req and req-bio
merging.
- blk_rq_get_max_sectors() and blk_queue_get_max_sectors() can be used
to query the maximum sector count for a given request or queue. The
calls will return the right value from the queue limits given the
type of command (RW, discard, write same, etc.)
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove special-casing of non-rw fs style requests (discard). The nomerge
flags are consolidated in blk_types.h, and rq_mergeable() and
bio_mergeable() have been modified to use them.
bio_is_rw() is used in place of bio_has_data() a few places. This is
done to to distinguish true reads and writes from other fs type requests
that carry a payload (e.g. write same).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Before call the blk_queue_congestion_threshold(),
the blk_queue_congestion_threshold() is already called at blk_queue_make_rquest().
Because this code is the duplicated, it has removed.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Previously, there was bio_clone() but it only allocated from the fs bio
set; as a result various users were open coding it and using
__bio_clone().
This changes bio_clone() to become bio_clone_bioset(), and then we add
bio_clone() and bio_clone_kmalloc() as wrappers around it, making use of
the functionality the last patch adedd.
This will also help in a later patch changing how bio cloning works.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
CC: Alasdair Kergon <agk@redhat.com>
CC: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now that we've got generic code for freeing bios allocated from bio
pools, this isn't needed anymore.
This patch also makes bio_free() static, since without bi_destructor
there should be no need for it to be called anywhere else.
bio_free() is now only called from bio_put, so we can refactor those a
bit - move some code from bio_put() to bio_free() and kill the redundant
bio->bi_next = NULL.
v5: Switch to BIO_KMALLOC_POOL ((void *)~0), per Boaz
v6: BIO_KMALLOC_POOL now NULL, drop bio_free's EXPORT_SYMBOL
v7: No #define BIO_KMALLOC_POOL anymore
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now that bios keep track of where they were allocated from,
bio_integrity_alloc_bioset() becomes redundant.
Remove bio_integrity_alloc_bioset() and drop bio_set argument from the
related functions and make them use bio->bi_pool.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When performing a cable pull test w/ active stress I/O using fio over
a dual port Intel 82599 FCoE CNA, w/ 256LUNs on one port and about 32LUNs
on the other, it is observed that the system becomes not usable due to
scsi-ml being busy printing the error messages for all the failing commands.
I don't believe this problem is specific to FCoE and these commands are
anyway failing due to link being down (DID_NO_CONNECT), just rate-limit
the messages here to solve this issue.
v2->v1: use __ratelimit() as Tomas Henzl mentioned as the proper way for
rate-limit per function. However, in this case, the failed i/o gets to
blk_end_request_err() and then blk_update_request(), which also has to
be rate-limited, as added in the v2 of this patch.
v3-v2: resolved conflict to apply on current 3.6-rc3 upstream tip.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: www.Open-FCoE.org <devel@open-fcoe.org>
Cc: Tomas Henzl <thenzl@redhat.com>
Cc: <linux-scsi@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now that cancel_delayed_work() can be safely called from IRQ handlers,
there's no reason to use __cancel_delayed_work(). Use
cancel_delayed_work() instead of __cancel_delayed_work() and mark the
latter deprecated.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roland Dreier <roland@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Now that mod_delayed_work() is safe to call from IRQ handlers,
__cancel_delayed_work() followed by queue_delayed_work() can be
replaced with mod_delayed_work().
Most conversions are straight-forward except for the following.
* net/core/link_watch.c: linkwatch_schedule_work() was doing a quite
elaborate dancing around its delayed_work. Collapse it such that
linkwatch_work is queued for immediate execution if LW_URGENT and
existing timer is kept otherwise.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This will allow md/raid to know why the unplug was called,
and will be able to act according - if !from_schedule it
is safe to perform tasks which could themselves schedule.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
MD raid1 prepares to dispatch request in unplug callback. If make_request in
low level queue also uses unplug callback to dispatch request, the low level
queue's unplug callback will not be called. Recheck the callback list helps
this case.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Both md and umem has similar code for getting notified on an
blk_finish_plug event.
Centralize this code in block/ and allow each driver to
provide its distinctive difference.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, request_queue has one request_list to allocate requests
from regardless of blkcg of the IO being issued. When the unified
request pool is used up, cfq proportional IO limits become meaningless
- whoever grabs the next request being freed wins the race regardless
of the configured weights.
This can be easily demonstrated by creating a blkio cgroup w/ very low
weight, put a program which can issue a lot of random direct IOs there
and running a sequential IO from a different cgroup. As soon as the
request pool is used up, the sequential IO bandwidth crashes.
This patch implements per-blkg request_list. Each blkg has its own
request_list and any IO allocates its request from the matching blkg
making blkcgs completely isolated in terms of request allocation.
* Root blkcg uses the request_list embedded in each request_queue,
which was renamed to @q->root_rl from @q->rq. While making blkcg rl
handling a bit harier, this enables avoiding most overhead for root
blkcg.
* Queue fullness is properly per request_list but bdi isn't blkcg
aware yet, so congestion state currently just follows the root
blkcg. As writeback isn't aware of blkcg yet, this works okay for
async congestion but readahead may get the wrong signals. It's
better than blkcg completely collapsing with shared request_list but
needs to be improved with future changes.
* After this change, each block cgroup gets a full request pool making
resource consumption of each cgroup higher. This makes allowing
non-root users to create cgroups less desirable; however, note that
allowing non-root users to directly manage cgroups is already
severely broken regardless of this patch - each block cgroup
consumes kernel memory and skews IO weight (IO weights are not
hierarchical).
v2: queue-sysfs.txt updated and patch description udpated as suggested
by Vivek.
v3: blk_get_rl() wasn't checking error return from
blkg_lookup_create() and may cause oops on lookup failure. Fix it
by falling back to root_rl on blkg lookup failures. This problem
was spotted by Rakesh Iyer <rni@google.com>.
v4: Updated to accomodate 458f27a982 "block: Avoid missed wakeup in
request waitqueue". blk_drain_queue() now wakes up waiters on all
blkg->rl on the target queue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Request allocation is about to be made per-blkg meaning that there'll
be multiple request lists.
* Make queue full state per request_list. blk_*queue_full() functions
are renamed to blk_*rl_full() and takes @rl instead of @q.
* Rename blk_init_free_list() to blk_init_rl() and make it take @rl
instead of @q. Also add @gfp_mask parameter.
* Add blk_exit_rl() instead of destroying rl directly from
blk_release_queue().
* Add request_list->q and make request alloc/free functions -
blk_free_request(), [__]freed_request(), __get_request() - take @rl
instead of @q.
This patch doesn't introduce any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add q->nr_rqs[] which currently behaves the same as q->rq.count[] and
move q->rq.elvpriv to q->nr_rqs_elvpriv. blk_drain_queue() is updated
to use q->nr_rqs[] instead of q->rq.count[].
These counters separates queue-wide request statistics from the
request list and allow implementation of per-queue request allocation.
While at it, properly indent fields of struct request_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Block layer very lazy allocation of ioc. It waits until the moment
ioc is absolutely necessary; unfortunately, that time could be inside
queue lock and __get_request() performs unlock - try alloc - retry
dancing.
Just allocate it up-front on entry to block layer. We're not saving
the rain forest by deferring it to the last possible moment and
complicating things unnecessarily.
This patch is to prepare for further updates to request allocation
path.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, there are two request allocation functions - get_request()
and get_request_wait(). The former tries to allocate a request once
and the latter keeps retrying until it succeeds. The latter wraps the
former and keeps retrying until allocation succeeds.
The combination of two functions deliver fallible non-wait allocation,
fallible wait allocation and unfailing wait allocation. However,
given that forward progress is guaranteed, fallible wait allocation
isn't all that useful and in fact nobody uses it.
This patch simplifies the interface as follows.
* get_request() is renamed to __get_request() and is only used by the
wrapper function.
* get_request_wait() is renamed to get_request(). It now takes
@gfp_mask and retries iff it contains %__GFP_WAIT.
This patch doesn't introduce any functional change and is to prepare
for further updates to request allocation path.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
