aboutsummaryrefslogtreecommitdiff
path: root/drivers/media/video/bt8xx/bttv-cards.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/media/video/bt8xx/bttv-cards.c')
-rw-r--r--drivers/media/video/bt8xx/bttv-cards.c22
1 files changed, 11 insertions, 11 deletions
diff --git a/drivers/media/video/bt8xx/bttv-cards.c b/drivers/media/video/bt8xx/bttv-cards.c
index dd6a7d68b07..3162223a2ff 100644
--- a/drivers/media/video/bt8xx/bttv-cards.c
+++ b/drivers/media/video/bt8xx/bttv-cards.c
@@ -4709,18 +4709,18 @@ adtvk503_audio(struct bttv *btv, struct video_audio *v, int set)
*
* The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin.
* GPIO pins are wired as:
- * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroler)
- * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroler)
- * GPIO[7] - DATA (xpoint) - P1[7] (microcontroler)
- * GPIO[8] - - P3[5] (microcontroler)
- * GPIO[9] - RESET (xpoint) - P3[6] (microcontroler)
- * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroler)
- * GPINTR - - P3[4] (microcontroler)
+ * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller)
+ * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller)
+ * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller)
+ * GPIO[8] - - P3[5] (microcontroller)
+ * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller)
+ * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller)
+ * GPINTR - - P3[4] (microcontroller)
*
- * The microcontroler is a 80C32 like. It should be possible to change xpoint
- * configuration either directly (as we are doing) or using the microcontroler
+ * The microcontroller is a 80C32 like. It should be possible to change xpoint
+ * configuration either directly (as we are doing) or using the microcontroller
* which is also wired to I2C interface. I have no further info on the
- * microcontroler features, one would need to disassembly the firmware.
+ * microcontroller features, one would need to disassembly the firmware.
* note: the vendor refused to give any information on this product, all
* that stuff was found using a multimeter! :)
*/
@@ -4788,7 +4788,7 @@ static void tibetCS16_init(struct bttv *btv)
* The analog switch is controlled by the "master", but the detection order
* of the four BT878A chips is in an order which I just don't understand.
* The "master" is actually the second controller to be detected. The
- * logic on the board uses logical numbers for the 4 controlers, but
+ * logic on the board uses logical numbers for the 4 controllers, but
* those numbers are different from the detection sequence. When working
* with the analog switch, we need to "map" from the detection sequence
* over to the board's logical controller number. This mapping sequence