diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/as3711.txt | 73 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/cros-ec.txt | 56 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/mc13xxx.txt | 36 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/omap-usb-host.txt | 80 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/omap-usb-tll.txt | 17 |
5 files changed, 259 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/mfd/as3711.txt b/Documentation/devicetree/bindings/mfd/as3711.txt new file mode 100644 index 00000000000..d98cf18c721 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/as3711.txt @@ -0,0 +1,73 @@ +AS3711 is an I2C PMIC from Austria MicroSystems with multiple DCDC and LDO power +supplies, a battery charger and an RTC. So far only bindings for the two stepup +DCDC converters are defined. Other DCDC and LDO supplies are configured, using +standard regulator properties, they must belong to a sub-node, called +"regulators" and be called "sd1" to "sd4" and "ldo1" to "ldo8." Stepup converter +configuration should be placed in a subnode, called "backlight." + +Compulsory properties: +- compatible : must be "ams,as3711" +- reg : specifies the I2C address + +To use the SU1 converter as a backlight source the following two properties must +be provided: +- su1-dev : framebuffer phandle +- su1-max-uA : maximum current + +To use the SU2 converter as a backlight source the following two properties must +be provided: +- su2-dev : framebuffer phandle +- su1-max-uA : maximum current + +Additionally one of these properties must be provided to select the type of +feedback used: +- su2-feedback-voltage : voltage feedback is used +- su2-feedback-curr1 : CURR1 input used for current feedback +- su2-feedback-curr2 : CURR2 input used for current feedback +- su2-feedback-curr3 : CURR3 input used for current feedback +- su2-feedback-curr-auto: automatic current feedback selection + +and one of these to select the over-voltage protection pin +- su2-fbprot-lx-sd4 : LX_SD4 is used for over-voltage protection +- su2-fbprot-gpio2 : GPIO2 is used for over-voltage protection +- su2-fbprot-gpio3 : GPIO3 is used for over-voltage protection +- su2-fbprot-gpio4 : GPIO4 is used for over-voltage protection + +If "su2-feedback-curr-auto" is selected, one or more of the following properties +have to be specified: +- su2-auto-curr1 : use CURR1 input for current feedback +- su2-auto-curr2 : use CURR2 input for current feedback +- su2-auto-curr3 : use CURR3 input for current feedback + +Example: + +as3711@40 { + compatible = "ams,as3711"; + reg = <0x40>; + + regulators { + sd4 { + regulator-name = "1.215V"; + regulator-min-microvolt = <1215000>; + regulator-max-microvolt = <1235000>; + }; + ldo2 { + regulator-name = "2.8V CPU"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + backlight { + compatible = "ams,as3711-bl"; + su2-dev = <&lcdc>; + su2-max-uA = <36000>; + su2-feedback-curr-auto; + su2-fbprot-gpio4; + su2-auto-curr1; + su2-auto-curr2; + su2-auto-curr3; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt new file mode 100644 index 00000000000..e0e59c58a1f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -0,0 +1,56 @@ +ChromeOS Embedded Controller + +Google's ChromeOS EC is a Cortex-M device which talks to the AP and +implements various function such as keyboard and battery charging. + +The EC can be connect through various means (I2C, SPI, LPC) and the +compatible string used depends on the inteface. Each connection method has +its own driver which connects to the top level interface-agnostic EC driver. +Other Linux driver (such as cros-ec-keyb for the matrix keyboard) connect to +the top-level driver. + +Required properties (I2C): +- compatible: "google,cros-ec-i2c" +- reg: I2C slave address + +Required properties (SPI): +- compatible: "google,cros-ec-spi" +- reg: SPI chip select + +Required properties (LPC): +- compatible: "google,cros-ec-lpc" +- reg: List of (IO address, size) pairs defining the interface uses + + +Example for I2C: + +i2c@12CA0000 { + cros-ec@1e { + reg = <0x1e>; + compatible = "google,cros-ec-i2c"; + interrupts = <14 0>; + interrupt-parent = <&wakeup_eint>; + wakeup-source; + }; + + +Example for SPI: + +spi@131b0000 { + ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0x0>; + interrupts = <14 0>; + interrupt-parent = <&wakeup_eint>; + wakeup-source; + spi-max-frequency = <5000000>; + controller-data { + cs-gpio = <&gpf0 3 4 3 0>; + samsung,spi-cs; + samsung,spi-feedback-delay = <2>; + }; + }; +}; + + +Example for LPC is not supplied as it is not yet implemented. diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index baf07987ae6..abd9e3cb2db 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -10,10 +10,40 @@ Optional properties: - fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used Sub-nodes: -- regulators : Contain the regulator nodes. The MC13892 regulators are - bound using their names as listed below with their registers and bits - for enabling. +- regulators : Contain the regulator nodes. The regulators are bound using + their names as listed below with their registers and bits for enabling. +MC13783 regulators: + sw1a : regulator SW1A (register 24, bit 0) + sw1b : regulator SW1B (register 25, bit 0) + sw2a : regulator SW2A (register 26, bit 0) + sw2b : regulator SW2B (register 27, bit 0) + sw3 : regulator SW3 (register 29, bit 20) + vaudio : regulator VAUDIO (register 32, bit 0) + viohi : regulator VIOHI (register 32, bit 3) + violo : regulator VIOLO (register 32, bit 6) + vdig : regulator VDIG (register 32, bit 9) + vgen : regulator VGEN (register 32, bit 12) + vrfdig : regulator VRFDIG (register 32, bit 15) + vrfref : regulator VRFREF (register 32, bit 18) + vrfcp : regulator VRFCP (register 32, bit 21) + vsim : regulator VSIM (register 33, bit 0) + vesim : regulator VESIM (register 33, bit 3) + vcam : regulator VCAM (register 33, bit 6) + vrfbg : regulator VRFBG (register 33, bit 9) + vvib : regulator VVIB (register 33, bit 11) + vrf1 : regulator VRF1 (register 33, bit 12) + vrf2 : regulator VRF2 (register 33, bit 15) + vmmc1 : regulator VMMC1 (register 33, bit 18) + vmmc2 : regulator VMMC2 (register 33, bit 21) + gpo1 : regulator GPO1 (register 34, bit 6) + gpo2 : regulator GPO2 (register 34, bit 8) + gpo3 : regulator GPO3 (register 34, bit 10) + gpo4 : regulator GPO4 (register 34, bit 12) + pwgt1spi : regulator PWGT1SPI (register 34, bit 15) + pwgt2spi : regulator PWGT2SPI (register 34, bit 16) + +MC13892 regulators: vcoincell : regulator VCOINCELL (register 13, bit 23) sw1 : regulator SW1 (register 24, bit 0) sw2 : regulator SW2 (register 25, bit 0) diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt new file mode 100644 index 00000000000..b381fa696bf --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt @@ -0,0 +1,80 @@ +OMAP HS USB Host + +Required properties: + +- compatible: should be "ti,usbhs-host" +- reg: should contain one register range i.e. start and length +- ti,hwmods: must contain "usb_host_hs" + +Optional properties: + +- num-ports: number of USB ports. Usually this is automatically detected + from the IP's revision register but can be overridden by specifying + this property. A maximum of 3 ports are supported at the moment. + +- portN-mode: String specifying the port mode for port N, where N can be + from 1 to 3. If the port mode is not specified, that port is treated + as unused. When specified, it must be one of the following. + "ehci-phy", + "ehci-tll", + "ehci-hsic", + "ohci-phy-6pin-datse0", + "ohci-phy-6pin-dpdm", + "ohci-phy-3pin-datse0", + "ohci-phy-4pin-dpdm", + "ohci-tll-6pin-datse0", + "ohci-tll-6pin-dpdm", + "ohci-tll-3pin-datse0", + "ohci-tll-4pin-dpdm", + "ohci-tll-2pin-datse0", + "ohci-tll-2pin-dpdm", + +- single-ulpi-bypass: Must be present if the controller contains a single + ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1 + +Required properties if child node exists: + +- #address-cells: Must be 1 +- #size-cells: Must be 1 +- ranges: must be present + +Properties for children: + +The OMAP HS USB Host subsystem contains EHCI and OHCI controllers. +See Documentation/devicetree/bindings/usb/omap-ehci.txt and +omap3-ohci.txt + +Example for OMAP4: + +usbhshost: usbhshost@4a064000 { + compatible = "ti,usbhs-host"; + reg = <0x4a064000 0x800>; + ti,hwmods = "usb_host_hs"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usbhsohci: ohci@4a064800 { + compatible = "ti,ohci-omap3", "usb-ohci"; + reg = <0x4a064800 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 76 0x4>; + }; + + usbhsehci: ehci@4a064c00 { + compatible = "ti,ehci-omap", "usb-ehci"; + reg = <0x4a064c00 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 77 0x4>; + }; +}; + +&usbhshost { + port1-mode = "ehci-phy"; + port2-mode = "ehci-tll"; + port3-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy 0 &hsusb3_phy>; +}; diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt new file mode 100644 index 00000000000..62fe69724e3 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt @@ -0,0 +1,17 @@ +OMAP HS USB Host TLL (Transceiver-Less Interface) + +Required properties: + +- compatible : should be "ti,usbhs-tll" +- reg : should contain one register range i.e. start and length +- interrupts : should contain the TLL module's interrupt +- ti,hwmod : must contain "usb_tll_hs" + +Example: + + usbhstll: usbhstll@4a062000 { + compatible = "ti,usbhs-tll"; + reg = <0x4a062000 0x1000>; + interrupts = <78>; + ti,hwmods = "usb_tll_hs"; + }; |