diff options
Diffstat (limited to 'arch/blackfin/mach-bf548')
| -rw-r--r-- | arch/blackfin/mach-bf548/boards/cm_bf548.c | 19 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/boards/ezkit.c | 12 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/dma.c | 8 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/include/mach/anomaly.h | 21 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/include/mach/blackfin.h | 89 |
5 files changed, 45 insertions, 104 deletions
diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c index f5a3c30a41b..e565aae11d7 100644 --- a/arch/blackfin/mach-bf548/boards/cm_bf548.c +++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c @@ -291,6 +291,8 @@ static struct platform_device bfin_sir3_device = { #endif #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#include <linux/smsc911x.h> + static struct resource smsc911x_resources[] = { { .name = "smsc911x-memory", @@ -304,11 +306,22 @@ static struct resource smsc911x_resources[] = { .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, }, }; + +static struct smsc911x_platform_config smsc911x_config = { + .flags = SMSC911X_USE_16BIT, + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, + .phy_interface = PHY_INTERFACE_MODE_MII, +}; + static struct platform_device smsc911x_device = { .name = "smsc911x", .id = 0, .num_resources = ARRAY_SIZE(smsc911x_resources), .resource = smsc911x_resources, + .dev = { + .platform_data = &smsc911x_config, + }, }; #endif @@ -473,7 +486,7 @@ static struct mtd_partition para_partitions[] = { .offset = 0, }, { .name = "linux kernel(nor)", - .size = 0x400000, + .size = 0x100000, .offset = MTDPART_OFS_APPEND, }, { .name = "file system(nor)", @@ -642,7 +655,7 @@ static struct resource bfin_spi1_resource[] = { /* SPI controller data */ static struct bfin5xx_spi_master bf54x_spi_master_info0 = { - .num_chipselect = 8, + .num_chipselect = 3, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, }; @@ -658,7 +671,7 @@ static struct platform_device bf54x_spi_master0 = { }; static struct bfin5xx_spi_master bf54x_spi_master_info1 = { - .num_chipselect = 8, + .num_chipselect = 3, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0}, }; diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c index dc0dd9b2bce..c66f3801274 100644 --- a/arch/blackfin/mach-bf548/boards/ezkit.c +++ b/arch/blackfin/mach-bf548/boards/ezkit.c @@ -99,8 +99,8 @@ static struct platform_device bfin_isp1760_device = { #include <mach/bf54x-lq043.h> static struct bfin_bf54xfb_mach_info bf54x_lq043_data = { - .width = 480, - .height = 272, + .width = 95, + .height = 54, .xres = {480, 480, 480}, .yres = {272, 272, 272}, .bpp = {24, 24, 24}, @@ -702,7 +702,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { #if defined(CONFIG_SND_BLACKFIN_AD1836) \ || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) { - .modalias = "ad1836-spi", + .modalias = "ad1836", .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ .bus_num = 1, .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, @@ -783,7 +783,7 @@ static struct resource bfin_spi1_resource[] = { /* SPI controller data */ static struct bfin5xx_spi_master bf54x_spi_master_info0 = { - .num_chipselect = 8, + .num_chipselect = 3, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, }; @@ -799,7 +799,7 @@ static struct platform_device bf54x_spi_master0 = { }; static struct bfin5xx_spi_master bf54x_spi_master_info1 = { - .num_chipselect = 8, + .num_chipselect = 3, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0}, }; @@ -869,7 +869,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info1[] = { I2C_BOARD_INFO("pcf8574_lcd", 0x22), }, #endif -#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE) +#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE) { I2C_BOARD_INFO("pcf8574_keypad", 0x27), .irq = 212, diff --git a/arch/blackfin/mach-bf548/dma.c b/arch/blackfin/mach-bf548/dma.c index 535980652bf..d9239bc05dd 100644 --- a/arch/blackfin/mach-bf548/dma.c +++ b/arch/blackfin/mach-bf548/dma.c @@ -91,16 +91,16 @@ int channel2irq(unsigned int channel) ret_irq = IRQ_SPI1; break; case CH_UART0_RX: - ret_irq = IRQ_UART_RX; + ret_irq = IRQ_UART0_RX; break; case CH_UART0_TX: - ret_irq = IRQ_UART_TX; + ret_irq = IRQ_UART0_TX; break; case CH_UART1_RX: - ret_irq = IRQ_UART_RX; + ret_irq = IRQ_UART1_RX; break; case CH_UART1_TX: - ret_irq = IRQ_UART_TX; + ret_irq = IRQ_UART1_TX; break; case CH_EPPI0: ret_irq = IRQ_EPPI0; diff --git a/arch/blackfin/mach-bf548/include/mach/anomaly.h b/arch/blackfin/mach-bf548/include/mach/anomaly.h index cd040fe0bc5..52b116ae522 100644 --- a/arch/blackfin/mach-bf548/include/mach/anomaly.h +++ b/arch/blackfin/mach-bf548/include/mach/anomaly.h @@ -7,7 +7,7 @@ */ /* This file should be up to date with: - * - Revision H, 01/16/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List + * - Revision I, 07/23/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List */ #ifndef _MACH_ANOMALY_H_ @@ -162,6 +162,8 @@ #define ANOMALY_05000430 (__SILICON_REVISION__ >= 2) /* Incorrect Use of Stack in Lockbox Firmware During Authentication */ #define ANOMALY_05000431 (__SILICON_REVISION__ < 3) +/* SW Breakpoints Ignored Upon Return From Lockbox Authentication */ +#define ANOMALY_05000434 (1) /* OTP Write Accesses Not Supported */ #define ANOMALY_05000442 (__SILICON_REVISION__ < 1) /* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */ @@ -176,12 +178,26 @@ #define ANOMALY_05000449 (__SILICON_REVISION__ == 1) /* USB DMA Mode 1 Short Packet Data Corruption */ #define ANOMALY_05000450 (1) +/* Incorrect Default Hysteresis Setting for RESET, NMI, and BMODE Signals */ +#define ANOMALY_05000452 (__SILICON_REVISION__ < 1) /* USB Receive Interrupt Is Not Generated in DMA Mode 1 */ -#define ANOMALY_05000456 (__SILICON_REVISION__ < 3) +#define ANOMALY_05000456 (1) +/* Host DMA Port Responds to Certain Bus Activity Without HOST_CE Assertion */ +#define ANOMALY_05000457 (1) +/* USB DMA Mode 1 Failure When Multiple USB DMA Channels Are Concurrently Enabled */ +#define ANOMALY_05000460 (1) /* False Hardware Error when RETI Points to Invalid Memory */ #define ANOMALY_05000461 (1) +/* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */ +#define ANOMALY_05000462 (1) +/* USB DMA RX Data Corruption */ +#define ANOMALY_05000463 (1) +/* USB TX DMA Hang */ +#define ANOMALY_05000464 (1) /* USB Rx DMA hang */ #define ANOMALY_05000465 (1) +/* TxPktRdy Bit Not Set for Transmit Endpoint When Core and DMA Access USB Endpoint FIFOs Simultaneously */ +#define ANOMALY_05000466 (1) /* Possible RX data corruption when control & data EP FIFOs are accessed via the core */ #define ANOMALY_05000467 (1) @@ -230,6 +246,7 @@ #define ANOMALY_05000364 (0) #define ANOMALY_05000380 (0) #define ANOMALY_05000400 (0) +#define ANOMALY_05000402 (0) #define ANOMALY_05000412 (0) #define ANOMALY_05000432 (0) #define ANOMALY_05000435 (0) diff --git a/arch/blackfin/mach-bf548/include/mach/blackfin.h b/arch/blackfin/mach-bf548/include/mach/blackfin.h index 6b97396d817..318667b2f03 100644 --- a/arch/blackfin/mach-bf548/include/mach/blackfin.h +++ b/arch/blackfin/mach-bf548/include/mach/blackfin.h @@ -72,97 +72,8 @@ #include "cdefBF549.h" #endif -/* UART 1*/ -#define bfin_read_UART_THR() bfin_read_UART1_THR() -#define bfin_write_UART_THR(val) bfin_write_UART1_THR(val) -#define bfin_read_UART_RBR() bfin_read_UART1_RBR() -#define bfin_write_UART_RBR(val) bfin_write_UART1_RBR(val) -#define bfin_read_UART_DLL() bfin_read_UART1_DLL() -#define bfin_write_UART_DLL(val) bfin_write_UART1_DLL(val) -#define bfin_read_UART_IER() bfin_read_UART1_IER() -#define bfin_write_UART_IER(val) bfin_write_UART1_IER(val) -#define bfin_read_UART_DLH() bfin_read_UART1_DLH() -#define bfin_write_UART_DLH(val) bfin_write_UART1_DLH(val) -#define bfin_read_UART_IIR() bfin_read_UART1_IIR() -#define bfin_write_UART_IIR(val) bfin_write_UART1_IIR(val) -#define bfin_read_UART_LCR() bfin_read_UART1_LCR() -#define bfin_write_UART_LCR(val) bfin_write_UART1_LCR(val) -#define bfin_read_UART_MCR() bfin_read_UART1_MCR() -#define bfin_write_UART_MCR(val) bfin_write_UART1_MCR(val) -#define bfin_read_UART_LSR() bfin_read_UART1_LSR() -#define bfin_write_UART_LSR(val) bfin_write_UART1_LSR(val) -#define bfin_read_UART_SCR() bfin_read_UART1_SCR() -#define bfin_write_UART_SCR(val) bfin_write_UART1_SCR(val) -#define bfin_read_UART_GCTL() bfin_read_UART1_GCTL() -#define bfin_write_UART_GCTL(val) bfin_write_UART1_GCTL(val) - #endif -/* MAP used DEFINES from BF533 to BF54x - so we don't need to change - * them in the driver, kernel, etc. */ - -/* UART_IIR Register */ -#define STATUS(x) ((x << 1) & 0x06) -#define STATUS_P1 0x02 -#define STATUS_P0 0x01 - -/* UART 0*/ - -/* DMA Channel */ -#define bfin_read_CH_UART_RX() bfin_read_CH_UART1_RX() -#define bfin_write_CH_UART_RX(val) bfin_write_CH_UART1_RX(val) -#define bfin_read_CH_UART_TX() bfin_read_CH_UART1_TX() -#define bfin_write_CH_UART_TX(val) bfin_write_CH_UART1_TX(val) -#define CH_UART_RX CH_UART1_RX -#define CH_UART_TX CH_UART1_TX - -/* System Interrupt Controller */ -#define bfin_read_IRQ_UART_RX() bfin_read_IRQ_UART1_RX() -#define bfin_write_IRQ_UART_RX(val) bfin_write_IRQ_UART1_RX(val) -#define bfin_read_IRQ_UART_TX() bfin_read_IRQ_UART1_TX() -#define bfin_write_IRQ_UART_TX(val) bfin_write_IRQ_UART1_TX(val) -#define bfin_read_IRQ_UART_ERROR() bfin_read_IRQ_UART1_ERROR() -#define bfin_write_IRQ_UART_ERROR(val) bfin_write_IRQ_UART1_ERROR(val) -#define IRQ_UART_RX IRQ_UART1_RX -#define IRQ_UART_TX IRQ_UART1_TX -#define IRQ_UART_ERROR IRQ_UART1_ERROR - -/* MMR Registers*/ -#define bfin_read_UART_THR() bfin_read_UART1_THR() -#define bfin_write_UART_THR(val) bfin_write_UART1_THR(val) -#define bfin_read_UART_RBR() bfin_read_UART1_RBR() -#define bfin_write_UART_RBR(val) bfin_write_UART1_RBR(val) -#define bfin_read_UART_DLL() bfin_read_UART1_DLL() -#define bfin_write_UART_DLL(val) bfin_write_UART1_DLL(val) -#define bfin_read_UART_IER() bfin_read_UART1_IER() -#define bfin_write_UART_IER(val) bfin_write_UART1_IER(val) -#define bfin_read_UART_DLH() bfin_read_UART1_DLH() -#define bfin_write_UART_DLH(val) bfin_write_UART1_DLH(val) -#define bfin_read_UART_IIR() bfin_read_UART1_IIR() -#define bfin_write_UART_IIR(val) bfin_write_UART1_IIR(val) -#define bfin_read_UART_LCR() bfin_read_UART1_LCR() -#define bfin_write_UART_LCR(val) bfin_write_UART1_LCR(val) -#define bfin_read_UART_MCR() bfin_read_UART1_MCR() -#define bfin_write_UART_MCR(val) bfin_write_UART1_MCR(val) -#define bfin_read_UART_LSR() bfin_read_UART1_LSR() -#define bfin_write_UART_LSR(val) bfin_write_UART1_LSR(val) -#define bfin_read_UART_SCR() bfin_read_UART1_SCR() -#define bfin_write_UART_SCR(val) bfin_write_UART1_SCR(val) -#define bfin_read_UART_GCTL() bfin_read_UART1_GCTL() -#define bfin_write_UART_GCTL(val) bfin_write_UART1_GCTL(val) - -#define BFIN_UART_THR UART1_THR -#define BFIN_UART_RBR UART1_RBR -#define BFIN_UART_DLL UART1_DLL -#define BFIN_UART_IER UART1_IER -#define BFIN_UART_DLH UART1_DLH -#define BFIN_UART_IIR UART1_IIR -#define BFIN_UART_LCR UART1_LCR -#define BFIN_UART_MCR UART1_MCR -#define BFIN_UART_LSR UART1_LSR -#define BFIN_UART_SCR UART1_SCR -#define BFIN_UART_GCTL UART1_GCTL - #define BFIN_UART_NR_PORTS 4 #define OFFSET_DLL 0x00 /* Divisor Latch (Low-Byte) */ |