From 39ddf3bf6463bc86041e806b43e014d50a144aa4 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:32 -0700 Subject: asus-wmi: Remove __init from asus_wmi_platform_init It's used by a non-init function. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/asus-wmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/asus-wmi.c b/drivers/platform/x86/asus-wmi.c index 832a3fd7c1c..c8c9842753d 100644 --- a/drivers/platform/x86/asus-wmi.c +++ b/drivers/platform/x86/asus-wmi.c @@ -1223,7 +1223,7 @@ static int asus_wmi_sysfs_init(struct platform_device *device) /* * Platform device */ -static int __init asus_wmi_platform_init(struct asus_wmi *asus) +static int asus_wmi_platform_init(struct asus_wmi *asus) { int rv; -- cgit v1.2.3 From 3a35125f97be0658305c9509c51077959c19b244 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:33 -0700 Subject: ibm_rtl: Remove warnings from casts of pointer to int Just print them as %p. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/ibm_rtl.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/ibm_rtl.c b/drivers/platform/x86/ibm_rtl.c index b1396e5b295..10563458408 100644 --- a/drivers/platform/x86/ibm_rtl.c +++ b/drivers/platform/x86/ibm_rtl.c @@ -288,7 +288,7 @@ static int __init ibm_rtl_init(void) { if ((readq(&tmp->signature) & RTL_MASK) == RTL_SIGNATURE) { phys_addr_t addr; unsigned int plen; - RTL_DEBUG("found RTL_SIGNATURE at %#llx\n", (u64)tmp); + RTL_DEBUG("found RTL_SIGNATURE at %p\n", tmp); rtl_table = tmp; /* The address, value, width and offset are platform * dependent and found in the ibm_rtl_table */ @@ -300,7 +300,7 @@ static int __init ibm_rtl_init(void) { RTL_DEBUG("addr = %#llx\n", (unsigned long long)addr); plen = rtl_cmd_width/sizeof(char); rtl_cmd_addr = rtl_port_map(addr, plen); - RTL_DEBUG("rtl_cmd_addr = %#llx\n", (u64)rtl_cmd_addr); + RTL_DEBUG("rtl_cmd_addr = %p\n", rtl_cmd_addr); if (!rtl_cmd_addr) { ret = -ENOMEM; break; -- cgit v1.2.3 From 249c720d88fa325522cb763dda09f8c9e8e964cb Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:34 -0700 Subject: acer-wmi: pr_ cleanups Convert pr_warning to pr_warn. Add some missing newlines to pr_ uses. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/acer-wmi.c | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index ac4e7f83ce6..fa8fa73f543 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -1081,7 +1081,7 @@ static acpi_status wmid3_get_device_status(u32 *value, u16 device) return AE_ERROR; } if (obj->buffer.length != 8) { - pr_warning("Unknown buffer length %d\n", obj->buffer.length); + pr_warn("Unknown buffer length %d\n", obj->buffer.length); kfree(obj); return AE_ERROR; } @@ -1090,8 +1090,8 @@ static acpi_status wmid3_get_device_status(u32 *value, u16 device) kfree(obj); if (return_value.error_code || return_value.ec_return_value) - pr_warning("Get Device Status failed: " - "0x%x - 0x%x\n", return_value.error_code, + pr_warn("Get Device Status failed: 0x%x - 0x%x\n", + return_value.error_code, return_value.ec_return_value); else *value = !!(return_value.devices & device); @@ -1317,7 +1317,7 @@ static void acer_wmi_notify(u32 value, void *context) status = wmi_get_event_data(value, &response); if (status != AE_OK) { - pr_warning("bad event status 0x%x\n", status); + pr_warn("bad event status 0x%x\n", status); return; } @@ -1326,12 +1326,12 @@ static void acer_wmi_notify(u32 value, void *context) if (!obj) return; if (obj->type != ACPI_TYPE_BUFFER) { - pr_warning("Unknown response received %d\n", obj->type); + pr_warn("Unknown response received %d\n", obj->type); kfree(obj); return; } if (obj->buffer.length != 8) { - pr_warning("Unknown buffer length %d\n", obj->buffer.length); + pr_warn("Unknown buffer length %d\n", obj->buffer.length); kfree(obj); return; } @@ -1356,11 +1356,11 @@ static void acer_wmi_notify(u32 value, void *context) } if (!sparse_keymap_report_event(acer_wmi_input_dev, return_value.key_num, 1, true)) - pr_warning("Unknown key number - 0x%x\n", + pr_warn("Unknown key number - 0x%x\n", return_value.key_num); break; default: - pr_warning("Unknown function number - %d - %d\n", + pr_warn("Unknown function number - %d - %d\n", return_value.function, return_value.key_num); break; } @@ -1389,7 +1389,7 @@ wmid3_set_lm_mode(struct lm_input_params *params, return AE_ERROR; } if (obj->buffer.length != 4) { - pr_warning("Unknown buffer length %d\n", obj->buffer.length); + pr_warn("Unknown buffer length %d\n", obj->buffer.length); kfree(obj); return AE_ERROR; } @@ -1414,11 +1414,11 @@ static int acer_wmi_enable_ec_raw(void) status = wmid3_set_lm_mode(¶ms, &return_value); if (return_value.error_code || return_value.ec_return_value) - pr_warning("Enabling EC raw mode failed: " - "0x%x - 0x%x\n", return_value.error_code, - return_value.ec_return_value); + pr_warn("Enabling EC raw mode failed: 0x%x - 0x%x\n", + return_value.error_code, + return_value.ec_return_value); else - pr_info("Enabled EC raw mode"); + pr_info("Enabled EC raw mode\n"); return status; } @@ -1437,9 +1437,9 @@ static int acer_wmi_enable_lm(void) status = wmid3_set_lm_mode(¶ms, &return_value); if (return_value.error_code || return_value.ec_return_value) - pr_warning("Enabling Launch Manager failed: " - "0x%x - 0x%x\n", return_value.error_code, - return_value.ec_return_value); + pr_warn("Enabling Launch Manager failed: 0x%x - 0x%x\n", + return_value.error_code, + return_value.ec_return_value); return status; } -- cgit v1.2.3 From 5ad77dcfb49a85715bcb9174a133cba140eda1bc Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:35 -0700 Subject: asus: Add pr_fmt and convert printks to pr_ Add pr_fmt, prefixes each log message. Convert printks to pr_. Convert pr_warning to pr_warn. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/asus-laptop.c | 34 ++++++++--------- drivers/platform/x86/asus-wmi.c | 20 +++++----- drivers/platform/x86/asus_acpi.c | 77 ++++++++++++++++---------------------- 3 files changed, 59 insertions(+), 72 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/asus-laptop.c b/drivers/platform/x86/asus-laptop.c index c53b3ff7978..d65df92e2ac 100644 --- a/drivers/platform/x86/asus-laptop.c +++ b/drivers/platform/x86/asus-laptop.c @@ -318,7 +318,7 @@ static int acpi_check_handle(acpi_handle handle, const char *method, if (status != AE_OK) { if (ret) - pr_warning("Error finding %s\n", method); + pr_warn("Error finding %s\n", method); return -ENODEV; } return 0; @@ -383,7 +383,7 @@ static int asus_kled_lvl(struct asus_laptop *asus) rv = acpi_evaluate_integer(asus->handle, METHOD_KBD_LIGHT_GET, ¶ms, &kblv); if (ACPI_FAILURE(rv)) { - pr_warning("Error reading kled level\n"); + pr_warn("Error reading kled level\n"); return -ENODEV; } return kblv; @@ -397,7 +397,7 @@ static int asus_kled_set(struct asus_laptop *asus, int kblv) kblv = 0; if (write_acpi_int(asus->handle, METHOD_KBD_LIGHT_SET, kblv)) { - pr_warning("Keyboard LED display write failed\n"); + pr_warn("Keyboard LED display write failed\n"); return -EINVAL; } return 0; @@ -531,7 +531,7 @@ static int asus_read_brightness(struct backlight_device *bd) rv = acpi_evaluate_integer(asus->handle, METHOD_BRIGHTNESS_GET, NULL, &value); if (ACPI_FAILURE(rv)) - pr_warning("Error reading brightness\n"); + pr_warn("Error reading brightness\n"); return value; } @@ -541,7 +541,7 @@ static int asus_set_brightness(struct backlight_device *bd, int value) struct asus_laptop *asus = bl_get_data(bd); if (write_acpi_int(asus->handle, METHOD_BRIGHTNESS_SET, value)) { - pr_warning("Error changing brightness\n"); + pr_warn("Error changing brightness\n"); return -EIO; } return 0; @@ -730,7 +730,7 @@ static ssize_t store_ledd(struct device *dev, struct device_attribute *attr, rv = parse_arg(buf, count, &value); if (rv > 0) { if (write_acpi_int(asus->handle, METHOD_LEDD, value)) { - pr_warning("LED display write failed\n"); + pr_warn("LED display write failed\n"); return -ENODEV; } asus->ledd_status = (u32) value; @@ -752,7 +752,7 @@ static int asus_wireless_status(struct asus_laptop *asus, int mask) rv = acpi_evaluate_integer(asus->handle, METHOD_WL_STATUS, NULL, &status); if (ACPI_FAILURE(rv)) { - pr_warning("Error reading Wireless status\n"); + pr_warn("Error reading Wireless status\n"); return -EINVAL; } return !!(status & mask); @@ -764,7 +764,7 @@ static int asus_wireless_status(struct asus_laptop *asus, int mask) static int asus_wlan_set(struct asus_laptop *asus, int status) { if (write_acpi_int(asus->handle, METHOD_WLAN, !!status)) { - pr_warning("Error setting wlan status to %d", status); + pr_warn("Error setting wlan status to %d\n", status); return -EIO; } return 0; @@ -792,7 +792,7 @@ static ssize_t store_wlan(struct device *dev, struct device_attribute *attr, static int asus_bluetooth_set(struct asus_laptop *asus, int status) { if (write_acpi_int(asus->handle, METHOD_BLUETOOTH, !!status)) { - pr_warning("Error setting bluetooth status to %d", status); + pr_warn("Error setting bluetooth status to %d\n", status); return -EIO; } return 0; @@ -821,7 +821,7 @@ static ssize_t store_bluetooth(struct device *dev, static int asus_wimax_set(struct asus_laptop *asus, int status) { if (write_acpi_int(asus->handle, METHOD_WIMAX, !!status)) { - pr_warning("Error setting wimax status to %d", status); + pr_warn("Error setting wimax status to %d\n", status); return -EIO; } return 0; @@ -850,7 +850,7 @@ static ssize_t store_wimax(struct device *dev, static int asus_wwan_set(struct asus_laptop *asus, int status) { if (write_acpi_int(asus->handle, METHOD_WWAN, !!status)) { - pr_warning("Error setting wwan status to %d", status); + pr_warn("Error setting wwan status to %d\n", status); return -EIO; } return 0; @@ -880,7 +880,7 @@ static void asus_set_display(struct asus_laptop *asus, int value) { /* no sanity check needed for now */ if (write_acpi_int(asus->handle, METHOD_SWITCH_DISPLAY, value)) - pr_warning("Error setting display\n"); + pr_warn("Error setting display\n"); return; } @@ -909,7 +909,7 @@ static ssize_t store_disp(struct device *dev, struct device_attribute *attr, static void asus_als_switch(struct asus_laptop *asus, int value) { if (write_acpi_int(asus->handle, METHOD_ALS_CONTROL, value)) - pr_warning("Error setting light sensor switch\n"); + pr_warn("Error setting light sensor switch\n"); asus->light_switch = value; } @@ -937,7 +937,7 @@ static ssize_t store_lssw(struct device *dev, struct device_attribute *attr, static void asus_als_level(struct asus_laptop *asus, int value) { if (write_acpi_int(asus->handle, METHOD_ALS_LEVEL, value)) - pr_warning("Error setting light sensor level\n"); + pr_warn("Error setting light sensor level\n"); asus->light_level = value; } @@ -976,7 +976,7 @@ static int asus_gps_status(struct asus_laptop *asus) rv = acpi_evaluate_integer(asus->handle, METHOD_GPS_STATUS, NULL, &status); if (ACPI_FAILURE(rv)) { - pr_warning("Error reading GPS status\n"); + pr_warn("Error reading GPS status\n"); return -ENODEV; } return !!status; @@ -1284,7 +1284,7 @@ static int asus_laptop_get_info(struct asus_laptop *asus) */ status = acpi_get_table(ACPI_SIG_DSDT, 1, &asus->dsdt_info); if (ACPI_FAILURE(status)) - pr_warning("Couldn't get the DSDT table header\n"); + pr_warn("Couldn't get the DSDT table header\n"); /* We have to write 0 on init this far for all ASUS models */ if (write_acpi_int_ret(asus->handle, "INIT", 0, &buffer)) { @@ -1296,7 +1296,7 @@ static int asus_laptop_get_info(struct asus_laptop *asus) status = acpi_evaluate_integer(asus->handle, "BSTS", NULL, &bsts_result); if (ACPI_FAILURE(status)) - pr_warning("Error calling BSTS\n"); + pr_warn("Error calling BSTS\n"); else if (bsts_result) pr_notice("BSTS called, 0x%02x returned\n", (uint) bsts_result); diff --git a/drivers/platform/x86/asus-wmi.c b/drivers/platform/x86/asus-wmi.c index c8c9842753d..00460cb9587 100644 --- a/drivers/platform/x86/asus-wmi.c +++ b/drivers/platform/x86/asus-wmi.c @@ -425,7 +425,7 @@ static void asus_rfkill_hotplug(struct asus_wmi *asus) if (asus->hotplug_slot) { bus = pci_find_bus(0, 1); if (!bus) { - pr_warning("Unable to find PCI bus 1?\n"); + pr_warn("Unable to find PCI bus 1?\n"); goto out_unlock; } @@ -436,12 +436,12 @@ static void asus_rfkill_hotplug(struct asus_wmi *asus) absent = (l == 0xffffffff); if (blocked != absent) { - pr_warning("BIOS says wireless lan is %s, " - "but the pci device is %s\n", - blocked ? "blocked" : "unblocked", - absent ? "absent" : "present"); - pr_warning("skipped wireless hotplug as probably " - "inappropriate for this model\n"); + pr_warn("BIOS says wireless lan is %s, " + "but the pci device is %s\n", + blocked ? "blocked" : "unblocked", + absent ? "absent" : "present"); + pr_warn("skipped wireless hotplug as probably " + "inappropriate for this model\n"); goto out_unlock; } @@ -500,7 +500,7 @@ static int asus_register_rfkill_notifier(struct asus_wmi *asus, char *node) ACPI_SYSTEM_NOTIFY, asus_rfkill_notify, asus); if (ACPI_FAILURE(status)) - pr_warning("Failed to register notify on %s\n", node); + pr_warn("Failed to register notify on %s\n", node); } else return -ENODEV; @@ -1583,12 +1583,12 @@ static int asus_wmi_probe(struct platform_device *pdev) int ret; if (!wmi_has_guid(ASUS_WMI_MGMT_GUID)) { - pr_warning("Management GUID not found\n"); + pr_warn("Management GUID not found\n"); return -ENODEV; } if (wdrv->event_guid && !wmi_has_guid(wdrv->event_guid)) { - pr_warning("Event GUID not found\n"); + pr_warn("Event GUID not found\n"); return -ENODEV; } diff --git a/drivers/platform/x86/asus_acpi.c b/drivers/platform/x86/asus_acpi.c index f503607c064..d9312b3073e 100644 --- a/drivers/platform/x86/asus_acpi.c +++ b/drivers/platform/x86/asus_acpi.c @@ -30,6 +30,8 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -581,8 +583,7 @@ static int read_led(const char *ledname, int ledmask) if (read_acpi_int(NULL, ledname, &led_status)) return led_status; else - printk(KERN_WARNING "Asus ACPI: Error reading LED " - "status\n"); + pr_warn("Error reading LED status\n"); } return (hotk->status & ledmask) ? 1 : 0; } @@ -621,8 +622,7 @@ write_led(const char __user *buffer, unsigned long count, led_out = !led_out; if (!write_acpi_int(hotk->handle, ledname, led_out, NULL)) - printk(KERN_WARNING "Asus ACPI: LED (%s) write failed\n", - ledname); + pr_warn("LED (%s) write failed\n", ledname); return rv; } @@ -679,8 +679,7 @@ static ssize_t ledd_proc_write(struct file *file, const char __user *buffer, if (rv > 0) { if (!write_acpi_int (hotk->handle, hotk->methods->mt_ledd, value, NULL)) - printk(KERN_WARNING - "Asus ACPI: LED display write failed\n"); + pr_warn("LED display write failed\n"); else hotk->ledd_status = (u32) value; } @@ -838,8 +837,7 @@ static int get_lcd_state(void) } else { /* We don't have to check anything if we are here */ if (!read_acpi_int(NULL, hotk->methods->lcd_status, &lcd)) - printk(KERN_WARNING - "Asus ACPI: Error reading LCD status\n"); + pr_warn("Error reading LCD status\n"); if (hotk->model == L2D) lcd = ~lcd; @@ -871,7 +869,7 @@ static int set_lcd_state(int value) the exact behaviour is simulated here */ } if (ACPI_FAILURE(status)) - printk(KERN_WARNING "Asus ACPI: Error switching LCD\n"); + pr_warn("Error switching LCD\n"); } return 0; @@ -915,13 +913,11 @@ static int read_brightness(struct backlight_device *bd) if (hotk->methods->brightness_get) { /* SPLV/GPLV laptop */ if (!read_acpi_int(hotk->handle, hotk->methods->brightness_get, &value)) - printk(KERN_WARNING - "Asus ACPI: Error reading brightness\n"); + pr_warn("Error reading brightness\n"); } else if (hotk->methods->brightness_status) { /* For D1 for example */ if (!read_acpi_int(NULL, hotk->methods->brightness_status, &value)) - printk(KERN_WARNING - "Asus ACPI: Error reading brightness\n"); + pr_warn("Error reading brightness\n"); } else /* No GPLV method */ value = hotk->brightness; return value; @@ -939,8 +935,7 @@ static int set_brightness(int value) if (hotk->methods->brightness_set) { if (!write_acpi_int(hotk->handle, hotk->methods->brightness_set, value, NULL)) { - printk(KERN_WARNING - "Asus ACPI: Error changing brightness\n"); + pr_warn("Error changing brightness\n"); ret = -EIO; } goto out; @@ -955,8 +950,7 @@ static int set_brightness(int value) NULL, NULL); (value > 0) ? value-- : value++; if (ACPI_FAILURE(status)) { - printk(KERN_WARNING - "Asus ACPI: Error changing brightness\n"); + pr_warn("Error changing brightness\n"); ret = -EIO; } } @@ -1008,7 +1002,7 @@ static void set_display(int value) /* no sanity check needed for now */ if (!write_acpi_int(hotk->handle, hotk->methods->display_set, value, NULL)) - printk(KERN_WARNING "Asus ACPI: Error setting display\n"); + pr_warn("Error setting display\n"); return; } @@ -1021,8 +1015,7 @@ static int disp_proc_show(struct seq_file *m, void *v) int value = 0; if (!read_acpi_int(hotk->handle, hotk->methods->display_get, &value)) - printk(KERN_WARNING - "Asus ACPI: Error reading display status\n"); + pr_warn("Error reading display status\n"); value &= 0x07; /* needed for some models, shouldn't hurt others */ seq_printf(m, "%d\n", value); return 0; @@ -1068,7 +1061,7 @@ asus_proc_add(char *name, const struct file_operations *proc_fops, mode_t mode, proc = proc_create_data(name, mode, acpi_device_dir(device), proc_fops, acpi_driver_data(device)); if (!proc) { - printk(KERN_WARNING " Unable to create %s fs entry\n", name); + pr_warn(" Unable to create %s fs entry\n", name); return -1; } proc->uid = asus_uid; @@ -1085,8 +1078,8 @@ static int asus_hotk_add_fs(struct acpi_device *device) mode = S_IFREG | S_IRUGO | S_IWUSR | S_IWGRP; } else { mode = S_IFREG | S_IRUSR | S_IRGRP | S_IWUSR | S_IWGRP; - printk(KERN_WARNING " asus_uid and asus_gid parameters are " - "deprecated, use chown and chmod instead!\n"); + pr_warn(" asus_uid and asus_gid parameters are " + "deprecated, use chown and chmod instead!\n"); } acpi_device_dir(device) = asus_proc_dir; @@ -1099,8 +1092,7 @@ static int asus_hotk_add_fs(struct acpi_device *device) proc->uid = asus_uid; proc->gid = asus_gid; } else { - printk(KERN_WARNING " Unable to create " PROC_INFO - " fs entry\n"); + pr_warn(" Unable to create " PROC_INFO " fs entry\n"); } if (hotk->methods->mt_wled) { @@ -1283,20 +1275,19 @@ static int asus_hotk_get_info(void) */ status = acpi_get_table(ACPI_SIG_DSDT, 1, &asus_info); if (ACPI_FAILURE(status)) - printk(KERN_WARNING " Couldn't get the DSDT table header\n"); + pr_warn(" Couldn't get the DSDT table header\n"); /* We have to write 0 on init this far for all ASUS models */ if (!write_acpi_int(hotk->handle, "INIT", 0, &buffer)) { - printk(KERN_ERR " Hotkey initialization failed\n"); + pr_err(" Hotkey initialization failed\n"); return -ENODEV; } /* This needs to be called for some laptops to init properly */ if (!read_acpi_int(hotk->handle, "BSTS", &bsts_result)) - printk(KERN_WARNING " Error calling BSTS\n"); + pr_warn(" Error calling BSTS\n"); else if (bsts_result) - printk(KERN_NOTICE " BSTS called, 0x%02x returned\n", - bsts_result); + pr_notice(" BSTS called, 0x%02x returned\n", bsts_result); /* * Try to match the object returned by INIT to the specific model. @@ -1324,23 +1315,21 @@ static int asus_hotk_get_info(void) if (asus_info && strncmp(asus_info->oem_table_id, "ODEM", 4) == 0) { hotk->model = P30; - printk(KERN_NOTICE - " Samsung P30 detected, supported\n"); + pr_notice(" Samsung P30 detected, supported\n"); hotk->methods = &model_conf[hotk->model]; kfree(model); return 0; } else { hotk->model = M2E; - printk(KERN_NOTICE " unsupported model %s, trying " - "default values\n", string); - printk(KERN_NOTICE - " send /proc/acpi/dsdt to the developers\n"); + pr_notice(" unsupported model %s, trying default values\n", + string); + pr_notice(" send /proc/acpi/dsdt to the developers\n"); kfree(model); return -ENODEV; } } hotk->methods = &model_conf[hotk->model]; - printk(KERN_NOTICE " %s model detected, supported\n", string); + pr_notice(" %s model detected, supported\n", string); /* Sort of per-model blacklist */ if (strncmp(string, "L2B", 3) == 0) @@ -1385,7 +1374,7 @@ static int asus_hotk_check(void) if (hotk->device->status.present) { result = asus_hotk_get_info(); } else { - printk(KERN_ERR " Hotkey device not present, aborting\n"); + pr_err(" Hotkey device not present, aborting\n"); return -EINVAL; } @@ -1399,8 +1388,7 @@ static int asus_hotk_add(struct acpi_device *device) acpi_status status = AE_OK; int result; - printk(KERN_NOTICE "Asus Laptop ACPI Extras version %s\n", - ASUS_ACPI_VERSION); + pr_notice("Asus Laptop ACPI Extras version %s\n", ASUS_ACPI_VERSION); hotk = kzalloc(sizeof(struct asus_hotk), GFP_KERNEL); if (!hotk) @@ -1428,15 +1416,14 @@ static int asus_hotk_add(struct acpi_device *device) acpi_evaluate_object(NULL, hotk->methods->brightness_down, NULL, NULL); if (ACPI_FAILURE(status)) - printk(KERN_WARNING " Error changing brightness\n"); + pr_warn(" Error changing brightness\n"); else { status = acpi_evaluate_object(NULL, hotk->methods->brightness_up, NULL, NULL); if (ACPI_FAILURE(status)) - printk(KERN_WARNING " Strange, error changing" - " brightness\n"); + pr_warn(" Strange, error changing brightness\n"); } } @@ -1488,7 +1475,7 @@ static int __init asus_acpi_init(void) asus_proc_dir = proc_mkdir(PROC_ASUS, acpi_root_dir); if (!asus_proc_dir) { - printk(KERN_ERR "Asus ACPI: Unable to create /proc entry\n"); + pr_err("Unable to create /proc entry\n"); acpi_bus_unregister_driver(&asus_hotk_driver); return -ENODEV; } @@ -1513,7 +1500,7 @@ static int __init asus_acpi_init(void) &asus_backlight_data, &props); if (IS_ERR(asus_backlight_device)) { - printk(KERN_ERR "Could not register asus backlight device\n"); + pr_err("Could not register asus backlight device\n"); asus_backlight_device = NULL; asus_acpi_exit(); return -ENODEV; -- cgit v1.2.3 From b4a4bc0bd1328b587a905e346d8494f9b9423cc5 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:36 -0700 Subject: compal-laptop: Convert printks to pr_ Add pr_fmt. Convert printks to pr_ removing DRIVER_NAME prefix. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/compal-laptop.c | 22 +++++++++------------- 1 file changed, 9 insertions(+), 13 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/compal-laptop.c b/drivers/platform/x86/compal-laptop.c index c16a27641ce..4c4a7422c5e 100644 --- a/drivers/platform/x86/compal-laptop.c +++ b/drivers/platform/x86/compal-laptop.c @@ -68,6 +68,8 @@ * only enabled on a JHL90 board until it is verified that they work on the * other boards too. See the extra_features variable. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -760,16 +762,14 @@ static struct rfkill *bt_rfkill; static int dmi_check_cb(const struct dmi_system_id *id) { - printk(KERN_INFO DRIVER_NAME": Identified laptop model '%s'\n", - id->ident); + pr_info("Identified laptop model '%s'\n", id->ident); extra_features = false; return 1; } static int dmi_check_cb_extra(const struct dmi_system_id *id) { - printk(KERN_INFO DRIVER_NAME": Identified laptop model '%s', " - "enabling extra features\n", + pr_info("Identified laptop model '%s', enabling extra features\n", id->ident); extra_features = true; return 1; @@ -956,14 +956,12 @@ static int __init compal_init(void) int ret; if (acpi_disabled) { - printk(KERN_ERR DRIVER_NAME": ACPI needs to be enabled for " - "this driver to work!\n"); + pr_err("ACPI needs to be enabled for this driver to work!\n"); return -ENODEV; } if (!force && !dmi_check_system(compal_dmi_table)) { - printk(KERN_ERR DRIVER_NAME": Motherboard not recognized (You " - "could try the module's force-parameter)"); + pr_err("Motherboard not recognized (You could try the module's force-parameter)\n"); return -ENODEV; } @@ -998,8 +996,7 @@ static int __init compal_init(void) if (ret) goto err_rfkill; - printk(KERN_INFO DRIVER_NAME": Driver "DRIVER_VERSION - " successfully loaded\n"); + pr_info("Driver " DRIVER_VERSION " successfully loaded\n"); return 0; err_rfkill: @@ -1064,7 +1061,7 @@ static void __exit compal_cleanup(void) rfkill_destroy(wifi_rfkill); rfkill_destroy(bt_rfkill); - printk(KERN_INFO DRIVER_NAME": Driver unloaded\n"); + pr_info("Driver unloaded\n"); } static int __devexit compal_remove(struct platform_device *pdev) @@ -1074,8 +1071,7 @@ static int __devexit compal_remove(struct platform_device *pdev) if (!extra_features) return 0; - printk(KERN_INFO DRIVER_NAME": Unloading: resetting fan control " - "to motherboard\n"); + pr_info("Unloading: resetting fan control to motherboard\n"); pwm_disable_control(); data = platform_get_drvdata(pdev); -- cgit v1.2.3 From eb8895241dfb6c26114928b186cc1810cbd57f1b Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:37 -0700 Subject: dell: Convert printks to pr_ Add pr_fmt. Remove hard coded prefixes and use pr_. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/dell-laptop.c | 12 ++++++------ drivers/platform/x86/dell-wmi-aio.c | 3 ++- drivers/platform/x86/dell-wmi.c | 17 ++++++++--------- 3 files changed, 16 insertions(+), 16 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/dell-laptop.c b/drivers/platform/x86/dell-laptop.c index de301aa8e5c..d3841de6a8c 100644 --- a/drivers/platform/x86/dell-laptop.c +++ b/drivers/platform/x86/dell-laptop.c @@ -11,6 +11,8 @@ * published by the Free Software Foundation. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -434,8 +436,7 @@ static int __init dell_setup_rfkill(void) int ret; if (dmi_check_system(dell_blacklist)) { - printk(KERN_INFO "dell-laptop: Blacklisted hardware detected - " - "not enabling rfkill\n"); + pr_info("Blacklisted hardware detected - not enabling rfkill\n"); return 0; } @@ -606,7 +607,7 @@ static int __init dell_init(void) dmi_walk(find_tokens, NULL); if (!da_tokens) { - printk(KERN_INFO "dell-laptop: Unable to find dmi tokens\n"); + pr_info("Unable to find dmi tokens\n"); return -ENODEV; } @@ -636,14 +637,13 @@ static int __init dell_init(void) ret = dell_setup_rfkill(); if (ret) { - printk(KERN_WARNING "dell-laptop: Unable to setup rfkill\n"); + pr_warn("Unable to setup rfkill\n"); goto fail_rfkill; } ret = i8042_install_filter(dell_laptop_i8042_filter); if (ret) { - printk(KERN_WARNING - "dell-laptop: Unable to install key filter\n"); + pr_warn("Unable to install key filter\n"); goto fail_filter; } diff --git a/drivers/platform/x86/dell-wmi-aio.c b/drivers/platform/x86/dell-wmi-aio.c index 0ed84573ae1..3f945457f71 100644 --- a/drivers/platform/x86/dell-wmi-aio.c +++ b/drivers/platform/x86/dell-wmi-aio.c @@ -15,6 +15,7 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ + #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include @@ -138,7 +139,7 @@ static int __init dell_wmi_aio_init(void) guid = dell_wmi_aio_find(); if (!guid) { - pr_warning("No known WMI GUID found\n"); + pr_warn("No known WMI GUID found\n"); return -ENXIO; } diff --git a/drivers/platform/x86/dell-wmi.c b/drivers/platform/x86/dell-wmi.c index 77f1d55414c..ce790827e19 100644 --- a/drivers/platform/x86/dell-wmi.c +++ b/drivers/platform/x86/dell-wmi.c @@ -23,6 +23,8 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -141,7 +143,7 @@ static void dell_wmi_notify(u32 value, void *context) status = wmi_get_event_data(value, &response); if (status != AE_OK) { - printk(KERN_INFO "dell-wmi: bad event status 0x%x\n", status); + pr_info("bad event status 0x%x\n", status); return; } @@ -153,8 +155,8 @@ static void dell_wmi_notify(u32 value, void *context) u16 *buffer_entry = (u16 *)obj->buffer.pointer; if (dell_new_hk_type && (buffer_entry[1] != 0x10)) { - printk(KERN_INFO "dell-wmi: Received unknown WMI event" - " (0x%x)\n", buffer_entry[1]); + pr_info("Received unknown WMI event (0x%x)\n", + buffer_entry[1]); kfree(obj); return; } @@ -167,8 +169,7 @@ static void dell_wmi_notify(u32 value, void *context) key = sparse_keymap_entry_from_scancode(dell_wmi_input_dev, reported_key); if (!key) { - printk(KERN_INFO "dell-wmi: Unknown key %x pressed\n", - reported_key); + pr_info("Unknown key %x pressed\n", reported_key); } else if ((key->keycode == KEY_BRIGHTNESSUP || key->keycode == KEY_BRIGHTNESSDOWN) && acpi_video) { /* Don't report brightness notifications that will also @@ -275,7 +276,7 @@ static int __init dell_wmi_init(void) acpi_status status; if (!wmi_has_guid(DELL_EVENT_GUID)) { - printk(KERN_WARNING "dell-wmi: No known WMI GUID found\n"); + pr_warn("No known WMI GUID found\n"); return -ENODEV; } @@ -290,9 +291,7 @@ static int __init dell_wmi_init(void) dell_wmi_notify, NULL); if (ACPI_FAILURE(status)) { dell_wmi_input_destroy(); - printk(KERN_ERR - "dell-wmi: Unable to register notify handler - %d\n", - status); + pr_err("Unable to register notify handler - %d\n", status); return -ENODEV; } -- cgit v1.2.3 From 22441ffeed17b94b28bd7c609f2cdb24d11e81f3 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:38 -0700 Subject: eeepc: Use pr_warn Just a trivial pr_warning to pr_warn conversion while adding a few missing newlines. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/eeepc-laptop.c | 21 +++++++++++---------- drivers/platform/x86/eeepc-wmi.c | 14 +++++++------- 2 files changed, 18 insertions(+), 17 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/eeepc-laptop.c b/drivers/platform/x86/eeepc-laptop.c index 2c1abf63957..1c45d92e216 100644 --- a/drivers/platform/x86/eeepc-laptop.c +++ b/drivers/platform/x86/eeepc-laptop.c @@ -228,7 +228,7 @@ static int set_acpi(struct eeepc_laptop *eeepc, int cm, int value) return -ENODEV; if (write_acpi_int(eeepc->handle, method, value)) - pr_warning("Error writing %s\n", method); + pr_warn("Error writing %s\n", method); return 0; } @@ -243,7 +243,7 @@ static int get_acpi(struct eeepc_laptop *eeepc, int cm) return -ENODEV; if (read_acpi_int(eeepc->handle, method, &value)) - pr_warning("Error reading %s\n", method); + pr_warn("Error reading %s\n", method); return value; } @@ -261,7 +261,7 @@ static int acpi_setter_handle(struct eeepc_laptop *eeepc, int cm, status = acpi_get_handle(eeepc->handle, (char *)method, handle); if (status != AE_OK) { - pr_warning("Error finding %s\n", method); + pr_warn("Error finding %s\n", method); return -ENODEV; } return 0; @@ -417,7 +417,7 @@ static ssize_t store_cpufv_disabled(struct device *dev, switch (value) { case 0: if (eeepc->cpufv_disabled) - pr_warning("cpufv enabled (not officially supported " + pr_warn("cpufv enabled (not officially supported " "on this model)\n"); eeepc->cpufv_disabled = false; return rv; @@ -609,7 +609,7 @@ static void eeepc_rfkill_hotplug(struct eeepc_laptop *eeepc, acpi_handle handle) bus = port->subordinate; if (!bus) { - pr_warning("Unable to find PCI bus?\n"); + pr_warn("Unable to find PCI bus 1?\n"); goto out_unlock; } @@ -621,12 +621,12 @@ static void eeepc_rfkill_hotplug(struct eeepc_laptop *eeepc, acpi_handle handle) absent = (l == 0xffffffff); if (blocked != absent) { - pr_warning("BIOS says wireless lan is %s, " - "but the pci device is %s\n", + pr_warn("BIOS says wireless lan is %s, " + "but the pci device is %s\n", blocked ? "blocked" : "unblocked", absent ? "absent" : "present"); - pr_warning("skipped wireless hotplug as probably " - "inappropriate for this model\n"); + pr_warn("skipped wireless hotplug as probably " + "inappropriate for this model\n"); goto out_unlock; } @@ -691,7 +691,8 @@ static int eeepc_register_rfkill_notifier(struct eeepc_laptop *eeepc, eeepc_rfkill_notify, eeepc); if (ACPI_FAILURE(status)) - pr_warning("Failed to register notify on %s\n", node); + pr_warn("Failed to register notify on %s\n", node); + /* * Refresh pci hotplug in case the rfkill state was * changed during setup. diff --git a/drivers/platform/x86/eeepc-wmi.c b/drivers/platform/x86/eeepc-wmi.c index 649dcadd8ea..4aa867a9b88 100644 --- a/drivers/platform/x86/eeepc-wmi.c +++ b/drivers/platform/x86/eeepc-wmi.c @@ -84,7 +84,7 @@ static const struct key_entry eeepc_wmi_keymap[] = { static acpi_status eeepc_wmi_parse_device(acpi_handle handle, u32 level, void *context, void **retval) { - pr_warning("Found legacy ATKD device (%s)", EEEPC_ACPI_HID); + pr_warn("Found legacy ATKD device (%s)\n", EEEPC_ACPI_HID); *(bool *)context = true; return AE_CTRL_TERMINATE; } @@ -105,12 +105,12 @@ static int eeepc_wmi_check_atkd(void) static int eeepc_wmi_probe(struct platform_device *pdev) { if (eeepc_wmi_check_atkd()) { - pr_warning("WMI device present, but legacy ATKD device is also " - "present and enabled."); - pr_warning("You probably booted with acpi_osi=\"Linux\" or " - "acpi_osi=\"!Windows 2009\""); - pr_warning("Can't load eeepc-wmi, use default acpi_osi " - "(preferred) or eeepc-laptop"); + pr_warn("WMI device present, but legacy ATKD device is also " + "present and enabled\n"); + pr_warn("You probably booted with acpi_osi=\"Linux\" or " + "acpi_osi=\"!Windows 2009\"\n"); + pr_warn("Can't load eeepc-wmi, use default acpi_osi " + "(preferred) or eeepc-laptop\n"); return -EBUSY; } return 0; -- cgit v1.2.3 From 77bad7c830e20085deba6a760ce85c13ecb12f4d Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:39 -0700 Subject: fujitsu-laptop: Convert printks to pr_ Added pr_fmt, converted printks and removed hard coded prefixes. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/fujitsu-laptop.c | 39 +++++++++++++++++------------------ 1 file changed, 19 insertions(+), 20 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/fujitsu-laptop.c b/drivers/platform/x86/fujitsu-laptop.c index 493054c2dbe..6b26666b37f 100644 --- a/drivers/platform/x86/fujitsu-laptop.c +++ b/drivers/platform/x86/fujitsu-laptop.c @@ -56,6 +56,8 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -585,8 +587,7 @@ static struct platform_driver fujitsupf_driver = { static void dmi_check_cb_common(const struct dmi_system_id *id) { acpi_handle handle; - printk(KERN_INFO "fujitsu-laptop: Identified laptop model '%s'.\n", - id->ident); + pr_info("Identified laptop model '%s'\n", id->ident); if (use_alt_lcd_levels == -1) { if (ACPI_SUCCESS(acpi_get_handle(NULL, "\\_SB.PCI0.LPCB.FJEX.SBL2", &handle))) @@ -691,11 +692,11 @@ static int acpi_fujitsu_add(struct acpi_device *device) result = acpi_bus_update_power(fujitsu->acpi_handle, &state); if (result) { - printk(KERN_ERR "Error reading power state\n"); + pr_err("Error reading power state\n"); goto err_unregister_input_dev; } - printk(KERN_INFO "ACPI: %s [%s] (%s)\n", + pr_info("ACPI: %s [%s] (%s)\n", acpi_device_name(device), acpi_device_bid(device), !device->power.state ? "on" : "off"); @@ -707,7 +708,7 @@ static int acpi_fujitsu_add(struct acpi_device *device) if (ACPI_FAILURE (acpi_evaluate_object (device->handle, METHOD_NAME__INI, NULL, NULL))) - printk(KERN_ERR "_INI Method failed\n"); + pr_err("_INI Method failed\n"); } /* do config (detect defaults) */ @@ -827,7 +828,7 @@ static int acpi_fujitsu_hotkey_add(struct acpi_device *device) error = kfifo_alloc(&fujitsu_hotkey->fifo, RINGBUFFERSIZE * sizeof(int), GFP_KERNEL); if (error) { - printk(KERN_ERR "kfifo_alloc failed\n"); + pr_err("kfifo_alloc failed\n"); goto err_stop; } @@ -859,13 +860,13 @@ static int acpi_fujitsu_hotkey_add(struct acpi_device *device) result = acpi_bus_update_power(fujitsu_hotkey->acpi_handle, &state); if (result) { - printk(KERN_ERR "Error reading power state\n"); + pr_err("Error reading power state\n"); goto err_unregister_input_dev; } - printk(KERN_INFO "ACPI: %s [%s] (%s)\n", - acpi_device_name(device), acpi_device_bid(device), - !device->power.state ? "on" : "off"); + pr_info("ACPI: %s [%s] (%s)\n", + acpi_device_name(device), acpi_device_bid(device), + !device->power.state ? "on" : "off"); fujitsu_hotkey->dev = device; @@ -875,7 +876,7 @@ static int acpi_fujitsu_hotkey_add(struct acpi_device *device) if (ACPI_FAILURE (acpi_evaluate_object (device->handle, METHOD_NAME__INI, NULL, NULL))) - printk(KERN_ERR "_INI Method failed\n"); + pr_err("_INI Method failed\n"); } i = 0; @@ -897,8 +898,7 @@ static int acpi_fujitsu_hotkey_add(struct acpi_device *device) call_fext_func(FUNC_RFKILL, 0x4, 0x0, 0x0); /* Suspect this is a keymap of the application panel, print it */ - printk(KERN_INFO "fujitsu-laptop: BTNI: [0x%x]\n", - call_fext_func(FUNC_BUTTONS, 0x0, 0x0, 0x0)); + pr_info("BTNI: [0x%x]\n", call_fext_func(FUNC_BUTTONS, 0x0, 0x0, 0x0)); #if defined(CONFIG_LEDS_CLASS) || defined(CONFIG_LEDS_CLASS_MODULE) if (call_fext_func(FUNC_LEDS, 0x0, 0x0, 0x0) & LOGOLAMP_POWERON) { @@ -907,8 +907,8 @@ static int acpi_fujitsu_hotkey_add(struct acpi_device *device) if (result == 0) { fujitsu_hotkey->logolamp_registered = 1; } else { - printk(KERN_ERR "fujitsu-laptop: Could not register " - "LED handler for logo lamp, error %i\n", result); + pr_err("Could not register LED handler for logo lamp, error %i\n", + result); } } @@ -919,8 +919,8 @@ static int acpi_fujitsu_hotkey_add(struct acpi_device *device) if (result == 0) { fujitsu_hotkey->kblamps_registered = 1; } else { - printk(KERN_ERR "fujitsu-laptop: Could not register " - "LED handler for keyboard lamps, error %i\n", result); + pr_err("Could not register LED handler for keyboard lamps, error %i\n", + result); } } #endif @@ -1169,8 +1169,7 @@ static int __init fujitsu_init(void) fujitsu->bl_device->props.power = 0; } - printk(KERN_INFO "fujitsu-laptop: driver " FUJITSU_DRIVER_VERSION - " successfully loaded.\n"); + pr_info("driver " FUJITSU_DRIVER_VERSION " successfully loaded\n"); return 0; @@ -1216,7 +1215,7 @@ static void __exit fujitsu_cleanup(void) kfree(fujitsu); - printk(KERN_INFO "fujitsu-laptop: driver unloaded.\n"); + pr_info("driver unloaded\n"); } module_init(fujitsu_init); -- cgit v1.2.3 From 611f5763fd0e38f896aa38346d4bc3f5c388b608 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:40 -0700 Subject: hdaps: Convert printks to pr_ Added pr_fmt, converted printks and removed hard coded prefixes. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/hdaps.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/hdaps.c b/drivers/platform/x86/hdaps.c index 067bf36d32f..5a34973dc16 100644 --- a/drivers/platform/x86/hdaps.c +++ b/drivers/platform/x86/hdaps.c @@ -26,6 +26,8 @@ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -238,7 +240,7 @@ static int hdaps_device_init(void) __check_latch(0x1611, 0x01)) goto out; - printk(KERN_DEBUG "hdaps: initial latch check good (0x%02x).\n", + printk(KERN_DEBUG "hdaps: initial latch check good (0x%02x)\n", __get_latch(0x1611)); outb(0x17, 0x1610); @@ -299,7 +301,7 @@ static int hdaps_probe(struct platform_device *dev) if (ret) return ret; - printk(KERN_INFO "hdaps: device successfully initialized.\n"); + pr_info("device successfully initialized\n"); return 0; } @@ -480,7 +482,7 @@ static struct attribute_group hdaps_attribute_group = { /* hdaps_dmi_match - found a match. return one, short-circuiting the hunt. */ static int __init hdaps_dmi_match(const struct dmi_system_id *id) { - printk(KERN_INFO "hdaps: %s detected.\n", id->ident); + pr_info("%s detected\n", id->ident); return 1; } @@ -488,8 +490,7 @@ static int __init hdaps_dmi_match(const struct dmi_system_id *id) static int __init hdaps_dmi_match_invert(const struct dmi_system_id *id) { hdaps_invert = (unsigned long)id->driver_data; - printk(KERN_INFO "hdaps: inverting axis (%u) readings.\n", - hdaps_invert); + pr_info("inverting axis (%u) readings\n", hdaps_invert); return hdaps_dmi_match(id); } @@ -543,7 +544,7 @@ static int __init hdaps_init(void) int ret; if (!dmi_check_system(hdaps_whitelist)) { - printk(KERN_WARNING "hdaps: supported laptop not found!\n"); + pr_warn("supported laptop not found!\n"); ret = -ENODEV; goto out; } @@ -595,7 +596,7 @@ static int __init hdaps_init(void) if (ret) goto out_idev; - printk(KERN_INFO "hdaps: driver successfully loaded.\n"); + pr_info("driver successfully loaded\n"); return 0; out_idev: @@ -609,7 +610,7 @@ out_driver: out_region: release_region(HDAPS_LOW_PORT, HDAPS_NR_PORTS); out: - printk(KERN_WARNING "hdaps: driver init failed (ret=%d)!\n", ret); + pr_warn("driver init failed (ret=%d)!\n", ret); return ret; } @@ -622,7 +623,7 @@ static void __exit hdaps_exit(void) platform_driver_unregister(&hdaps_driver); release_region(HDAPS_LOW_PORT, HDAPS_NR_PORTS); - printk(KERN_INFO "hdaps: driver unloaded.\n"); + pr_info("driver unloaded\n"); } module_init(hdaps_init); -- cgit v1.2.3 From b5a4223c1ce5edbaae3db9494de8dcb2d08a755b Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:41 -0700 Subject: hp-wmi: Convert printks to pr_ Added pr_fmt and converted printks to pr_. Removed now unused PREFIX and UNIMPL #defines. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/hp-wmi.c | 43 +++++++++++++++++-------------------------- 1 file changed, 17 insertions(+), 26 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/hp-wmi.c b/drivers/platform/x86/hp-wmi.c index 1bc4a7539ba..f94017bcdd6 100644 --- a/drivers/platform/x86/hp-wmi.c +++ b/drivers/platform/x86/hp-wmi.c @@ -24,6 +24,8 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -54,9 +56,6 @@ MODULE_ALIAS("wmi:5FB7F034-2C63-45e9-BE91-3D44E2C707E4"); #define HPWMI_HOTKEY_QUERY 0xc #define HPWMI_WIRELESS2_QUERY 0x1b -#define PREFIX "HP WMI: " -#define UNIMP "Unimplemented " - enum hp_wmi_radio { HPWMI_WIFI = 0, HPWMI_BLUETOOTH = 1, @@ -228,9 +227,8 @@ static int hp_wmi_perform_query(int query, int write, void *buffer, if (bios_return->return_code) { if (bios_return->return_code != HPWMI_RET_UNKNOWN_CMDTYPE) - printk(KERN_WARNING PREFIX "query 0x%x returned " - "error 0x%x\n", - query, bios_return->return_code); + pr_warn("query 0x%x returned error 0x%x\n", + query, bios_return->return_code); kfree(obj); return bios_return->return_code; } @@ -384,8 +382,7 @@ static int hp_wmi_rfkill2_refresh(void) if (num >= state.count || devstate->rfkill_id != rfkill2[i].id) { - printk(KERN_WARNING PREFIX "power configuration of " - "the wireless devices unexpectedly changed\n"); + pr_warn("power configuration of the wireless devices unexpectedly changed\n"); continue; } @@ -471,7 +468,7 @@ static void hp_wmi_notify(u32 value, void *context) status = wmi_get_event_data(value, &response); if (status != AE_OK) { - printk(KERN_INFO PREFIX "bad event status 0x%x\n", status); + pr_info("bad event status 0x%x\n", status); return; } @@ -480,8 +477,7 @@ static void hp_wmi_notify(u32 value, void *context) if (!obj) return; if (obj->type != ACPI_TYPE_BUFFER) { - printk(KERN_INFO "hp-wmi: Unknown response received %d\n", - obj->type); + pr_info("Unknown response received %d\n", obj->type); kfree(obj); return; } @@ -498,8 +494,7 @@ static void hp_wmi_notify(u32 value, void *context) event_id = *location; event_data = *(location + 2); } else { - printk(KERN_INFO "hp-wmi: Unknown buffer length %d\n", - obj->buffer.length); + pr_info("Unknown buffer length %d\n", obj->buffer.length); kfree(obj); return; } @@ -527,8 +522,7 @@ static void hp_wmi_notify(u32 value, void *context) if (!sparse_keymap_report_event(hp_wmi_input_dev, key_code, 1, true)) - printk(KERN_INFO PREFIX "Unknown key code - 0x%x\n", - key_code); + pr_info("Unknown key code - 0x%x\n", key_code); break; case HPWMI_WIRELESS: if (rfkill2_count) { @@ -550,14 +544,12 @@ static void hp_wmi_notify(u32 value, void *context) hp_wmi_get_hw_state(HPWMI_WWAN)); break; case HPWMI_CPU_BATTERY_THROTTLE: - printk(KERN_INFO PREFIX UNIMP "CPU throttle because of 3 Cell" - " battery event detected\n"); + pr_info("Unimplemented CPU throttle because of 3 Cell battery event detected\n"); break; case HPWMI_LOCK_SWITCH: break; default: - printk(KERN_INFO PREFIX "Unknown event_id - %d - 0x%x\n", - event_id, event_data); + pr_info("Unknown event_id - %d - 0x%x\n", event_id, event_data); break; } } @@ -705,7 +697,7 @@ static int __devinit hp_wmi_rfkill2_setup(struct platform_device *device) return err; if (state.count > HPWMI_MAX_RFKILL2_DEVICES) { - printk(KERN_WARNING PREFIX "unable to parse 0x1b query output\n"); + pr_warn("unable to parse 0x1b query output\n"); return -EINVAL; } @@ -727,14 +719,14 @@ static int __devinit hp_wmi_rfkill2_setup(struct platform_device *device) name = "hp-wwan"; break; default: - printk(KERN_WARNING PREFIX "unknown device type 0x%x\n", - state.device[i].radio_type); + pr_warn("unknown device type 0x%x\n", + state.device[i].radio_type); continue; } if (!state.device[i].vendor_id) { - printk(KERN_WARNING PREFIX "zero device %d while %d " - "reported\n", i, state.count); + pr_warn("zero device %d while %d reported\n", + i, state.count); continue; } @@ -755,8 +747,7 @@ static int __devinit hp_wmi_rfkill2_setup(struct platform_device *device) IS_HWBLOCKED(state.device[i].power)); if (!(state.device[i].power & HPWMI_POWER_BIOS)) - printk(KERN_INFO PREFIX "device %s blocked by BIOS\n", - name); + pr_info("device %s blocked by BIOS\n", name); err = rfkill_register(rfkill); if (err) { -- cgit v1.2.3 From 323623a717c7feec3f36099f4caa18b3319c5cca Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:42 -0700 Subject: ibm_rtl: Use pr_fmt and pr_ Remove hard coded prefixes from logging messages. Neaten RTL_DEBUG macro and uses. Convert __FUNCTION__ to __func__. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/ibm_rtl.c | 19 +++++++++++-------- 1 file changed, 11 insertions(+), 8 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/ibm_rtl.c b/drivers/platform/x86/ibm_rtl.c index 10563458408..811d436cd67 100644 --- a/drivers/platform/x86/ibm_rtl.c +++ b/drivers/platform/x86/ibm_rtl.c @@ -22,6 +22,8 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -69,9 +71,10 @@ struct ibm_rtl_table { #define RTL_SIGNATURE 0x0000005f4c54525fULL #define RTL_MASK 0x000000ffffffffffULL -#define RTL_DEBUG(A, ...) do { \ - if (debug) \ - pr_info("ibm-rtl: " A, ##__VA_ARGS__ ); \ +#define RTL_DEBUG(fmt, ...) \ +do { \ + if (debug) \ + pr_info(fmt, ##__VA_ARGS__); \ } while (0) static DEFINE_MUTEX(rtl_lock); @@ -114,7 +117,7 @@ static int ibm_rtl_write(u8 value) int ret = 0, count = 0; static u32 cmd_port_val; - RTL_DEBUG("%s(%d)\n", __FUNCTION__, value); + RTL_DEBUG("%s(%d)\n", __func__, value); value = value == 1 ? RTL_CMD_ENTER_PRTM : RTL_CMD_EXIT_PRTM; @@ -144,8 +147,8 @@ static int ibm_rtl_write(u8 value) while (ioread8(&rtl_table->command)) { msleep(10); if (count++ > 500) { - pr_err("ibm-rtl: Hardware not responding to " - "mode switch request\n"); + pr_err("Hardware not responding to " + "mode switch request\n"); ret = -EIO; break; } @@ -250,7 +253,7 @@ static int __init ibm_rtl_init(void) { int ret = -ENODEV, i; if (force) - pr_warning("ibm-rtl: module loaded by force\n"); + pr_warn("module loaded by force\n"); /* first ensure that we are running on IBM HW */ else if (efi_enabled || !dmi_check_system(ibm_rtl_dmi_table)) return -ENODEV; @@ -295,7 +298,7 @@ static int __init ibm_rtl_init(void) { rtl_cmd_width = ioread8(&rtl_table->cmd_granularity); rtl_cmd_type = ioread8(&rtl_table->cmd_address_type); RTL_DEBUG("rtl_cmd_width = %u, rtl_cmd_type = %u\n", - rtl_cmd_width, rtl_cmd_type); + rtl_cmd_width, rtl_cmd_type); addr = ioread32(&rtl_table->cmd_port_address); RTL_DEBUG("addr = %#llx\n", (unsigned long long)addr); plen = rtl_cmd_width/sizeof(char); -- cgit v1.2.3 From 9ab23989d3e774f4545c83eeab0137e35f7115be Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:43 -0700 Subject: ideapad-laptop: Add pr_fmt Add pr_fmt to prefix logging messages. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/ideapad-laptop.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/ideapad-laptop.c b/drivers/platform/x86/ideapad-laptop.c index 21b101899ba..bfdda33feb2 100644 --- a/drivers/platform/x86/ideapad-laptop.c +++ b/drivers/platform/x86/ideapad-laptop.c @@ -20,6 +20,8 @@ * 02110-1301, USA. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include -- cgit v1.2.3 From 4686f6df69c5bca5ea795e01048d32f6eed07ba7 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:44 -0700 Subject: intel_menlow: Add pr_fmt and use pr_ Add pr_fmt to prefix the logging messages. Convert printk to pr_. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/intel_menlow.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/intel_menlow.c b/drivers/platform/x86/intel_menlow.c index eacd5da7dd2..809adea4965 100644 --- a/drivers/platform/x86/intel_menlow.c +++ b/drivers/platform/x86/intel_menlow.c @@ -27,6 +27,8 @@ * to get/set bandwidth. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -135,8 +137,7 @@ static int memory_set_cur_bandwidth(struct thermal_cooling_device *cdev, acpi_evaluate_integer(handle, MEMORY_SET_BANDWIDTH, &arg_list, &temp); - printk(KERN_INFO - "Bandwidth value was %ld: status is %d\n", state, status); + pr_info("Bandwidth value was %ld: status is %d\n", state, status); if (ACPI_FAILURE(status)) return -EFAULT; -- cgit v1.2.3 From 9a2ffd168ef8ec3705060ffb21d6dcb20eeb9506 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:45 -0700 Subject: intel_pmic_gpio: Convert printks to pr_ Add #define pr_fmt(fmt) "%s: " fmt, __func__ to prefix function name to each output message. Convert printks to pr_. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/intel_pmic_gpio.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/intel_pmic_gpio.c b/drivers/platform/x86/intel_pmic_gpio.c index 464bb3fc4d8..1686c1e07d5 100644 --- a/drivers/platform/x86/intel_pmic_gpio.c +++ b/drivers/platform/x86/intel_pmic_gpio.c @@ -19,6 +19,8 @@ * Moorestown platform PMIC chip */ +#define pr_fmt(fmt) "%s: " fmt, __func__ + #include #include #include @@ -90,8 +92,7 @@ static void pmic_program_irqtype(int gpio, int type) static int pmic_gpio_direction_input(struct gpio_chip *chip, unsigned offset) { if (offset > 8) { - printk(KERN_ERR - "%s: only pin 0-7 support input\n", __func__); + pr_err("only pin 0-7 support input\n"); return -1;/* we only have 8 GPIO can use as input */ } return intel_scu_ipc_update_register(GPIO0 + offset, @@ -116,8 +117,7 @@ static int pmic_gpio_direction_output(struct gpio_chip *chip, value ? 1 << (offset - 16) : 0, 1 << (offset - 16)); else { - printk(KERN_ERR - "%s: invalid PMIC GPIO pin %d!\n", __func__, offset); + pr_err("invalid PMIC GPIO pin %d!\n", offset); WARN_ON(1); } @@ -260,7 +260,7 @@ static int __devinit platform_pmic_gpio_probe(struct platform_device *pdev) /* setting up SRAM mapping for GPIOINT register */ pg->gpiointr = ioremap_nocache(pdata->gpiointr, 8); if (!pg->gpiointr) { - printk(KERN_ERR "%s: Can not map GPIOINT.\n", __func__); + pr_err("Can not map GPIOINT\n"); retval = -EINVAL; goto err2; } @@ -281,13 +281,13 @@ static int __devinit platform_pmic_gpio_probe(struct platform_device *pdev) pg->chip.dev = dev; retval = gpiochip_add(&pg->chip); if (retval) { - printk(KERN_ERR "%s: Can not add pmic gpio chip.\n", __func__); + pr_err("Can not add pmic gpio chip\n"); goto err; } retval = request_irq(pg->irq, pmic_irq_handler, 0, "pmic", pg); if (retval) { - printk(KERN_WARNING "pmic: Interrupt request failed\n"); + pr_warn("Interrupt request failed\n"); goto err; } -- cgit v1.2.3 From f9dcf192ed527fbf2f3a8a3574006d1ae855100b Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:46 -0700 Subject: msi-laptop: pr_ neatening Just making it a bit more like other logging message uses. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/msi-laptop.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/msi-laptop.c b/drivers/platform/x86/msi-laptop.c index 23fb2afda00..f89c0b6a9ae 100644 --- a/drivers/platform/x86/msi-laptop.c +++ b/drivers/platform/x86/msi-laptop.c @@ -447,7 +447,7 @@ static struct platform_device *msipf_device; static int dmi_check_cb(const struct dmi_system_id *id) { - pr_info("Identified laptop model '%s'.\n", id->ident); + pr_info("Identified laptop model '%s'\n", id->ident); return 1; } @@ -875,8 +875,7 @@ static int __init msi_init(void) /* Register backlight stuff */ if (acpi_video_backlight_support()) { - pr_info("Brightness ignored, must be controlled " - "by ACPI video driver\n"); + pr_info("Brightness ignored, must be controlled by ACPI video driver\n"); } else { struct backlight_properties props; memset(&props, 0, sizeof(struct backlight_properties)); @@ -930,7 +929,7 @@ static int __init msi_init(void) if (auto_brightness != 2) set_auto_brightness(auto_brightness); - pr_info("driver "MSI_DRIVER_VERSION" successfully loaded.\n"); + pr_info("driver " MSI_DRIVER_VERSION " successfully loaded\n"); return 0; @@ -978,7 +977,7 @@ static void __exit msi_cleanup(void) if (auto_brightness != 2) set_auto_brightness(1); - pr_info("driver unloaded.\n"); + pr_info("driver unloaded\n"); } module_init(msi_init); -- cgit v1.2.3 From dd3c7f2308e91d6ecbe5cd8a3310bb49e47e1ae7 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:47 -0700 Subject: msi-wmi: Use pr_fmt and pr_ Added pr_fmt. Removed now unused #define DRV_PFX Convert dprintk to pr_debug. Convert printks to pr_. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/msi-wmi.c | 45 +++++++++++++++++++----------------------- 1 file changed, 20 insertions(+), 25 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/msi-wmi.c b/drivers/platform/x86/msi-wmi.c index d5419c9ec07..c832e3356cd 100644 --- a/drivers/platform/x86/msi-wmi.c +++ b/drivers/platform/x86/msi-wmi.c @@ -20,6 +20,7 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include #include @@ -36,13 +37,10 @@ MODULE_ALIAS("wmi:551A1F84-FBDD-4125-91DB-3EA8F44F1D45"); MODULE_ALIAS("wmi:B6F3EEF2-3D2F-49DC-9DE3-85BCE18C62F2"); #define DRV_NAME "msi-wmi" -#define DRV_PFX DRV_NAME ": " #define MSIWMI_BIOS_GUID "551A1F84-FBDD-4125-91DB-3EA8F44F1D45" #define MSIWMI_EVENT_GUID "B6F3EEF2-3D2F-49DC-9DE3-85BCE18C62F2" -#define dprintk(msg...) pr_debug(DRV_PFX msg) - #define SCANCODE_BASE 0xD0 #define MSI_WMI_BRIGHTNESSUP SCANCODE_BASE #define MSI_WMI_BRIGHTNESSDOWN (SCANCODE_BASE + 1) @@ -78,7 +76,7 @@ static int msi_wmi_query_block(int instance, int *ret) if (!obj || obj->type != ACPI_TYPE_INTEGER) { if (obj) { - printk(KERN_ERR DRV_PFX "query block returned object " + pr_err("query block returned object " "type: %d - buffer length:%d\n", obj->type, obj->type == ACPI_TYPE_BUFFER ? obj->buffer.length : 0); @@ -97,8 +95,8 @@ static int msi_wmi_set_block(int instance, int value) struct acpi_buffer input = { sizeof(int), &value }; - dprintk("Going to set block of instance: %d - value: %d\n", - instance, value); + pr_debug("Going to set block of instance: %d - value: %d\n", + instance, value); status = wmi_set_block(MSIWMI_BIOS_GUID, instance, &input); @@ -112,20 +110,19 @@ static int bl_get(struct backlight_device *bd) /* Instance 1 is "get backlight", cmp with DSDT */ err = msi_wmi_query_block(1, &ret); if (err) { - printk(KERN_ERR DRV_PFX "Could not query backlight: %d\n", err); + pr_err("Could not query backlight: %d\n", err); return -EINVAL; } - dprintk("Get: Query block returned: %d\n", ret); + pr_debug("Get: Query block returned: %d\n", ret); for (level = 0; level < ARRAY_SIZE(backlight_map); level++) { if (backlight_map[level] == ret) { - dprintk("Current backlight level: 0x%X - index: %d\n", - backlight_map[level], level); + pr_debug("Current backlight level: 0x%X - index: %d\n", + backlight_map[level], level); break; } } if (level == ARRAY_SIZE(backlight_map)) { - printk(KERN_ERR DRV_PFX "get: Invalid brightness value: 0x%X\n", - ret); + pr_err("get: Invalid brightness value: 0x%X\n", ret); return -EINVAL; } return level; @@ -156,7 +153,7 @@ static void msi_wmi_notify(u32 value, void *context) status = wmi_get_event_data(value, &response); if (status != AE_OK) { - printk(KERN_INFO DRV_PFX "bad event status 0x%x\n", status); + pr_info("bad event status 0x%x\n", status); return; } @@ -164,7 +161,7 @@ static void msi_wmi_notify(u32 value, void *context) if (obj && obj->type == ACPI_TYPE_INTEGER) { int eventcode = obj->integer.value; - dprintk("Eventcode: 0x%x\n", eventcode); + pr_debug("Eventcode: 0x%x\n", eventcode); key = sparse_keymap_entry_from_scancode(msi_wmi_input_dev, eventcode); if (key) { @@ -175,8 +172,8 @@ static void msi_wmi_notify(u32 value, void *context) /* Ignore event if the same event happened in a 50 ms timeframe -> Key press may result in 10-20 GPEs */ if (ktime_to_us(diff) < 1000 * 50) { - dprintk("Suppressed key event 0x%X - " - "Last press was %lld us ago\n", + pr_debug("Suppressed key event 0x%X - " + "Last press was %lld us ago\n", key->code, ktime_to_us(diff)); return; } @@ -187,17 +184,16 @@ static void msi_wmi_notify(u32 value, void *context) (!acpi_video_backlight_support() || (key->code != MSI_WMI_BRIGHTNESSUP && key->code != MSI_WMI_BRIGHTNESSDOWN))) { - dprintk("Send key: 0x%X - " - "Input layer keycode: %d\n", key->code, - key->keycode); + pr_debug("Send key: 0x%X - " + "Input layer keycode: %d\n", + key->code, key->keycode); sparse_keymap_report_entry(msi_wmi_input_dev, key, 1, true); } } else - printk(KERN_INFO "Unknown key pressed - %x\n", - eventcode); + pr_info("Unknown key pressed - %x\n", eventcode); } else - printk(KERN_INFO DRV_PFX "Unknown event received\n"); + pr_info("Unknown event received\n"); kfree(response.pointer); } @@ -238,8 +234,7 @@ static int __init msi_wmi_init(void) int err; if (!wmi_has_guid(MSIWMI_EVENT_GUID)) { - printk(KERN_ERR - "This machine doesn't have MSI-hotkeys through WMI\n"); + pr_err("This machine doesn't have MSI-hotkeys through WMI\n"); return -ENODEV; } err = wmi_install_notify_handler(MSIWMI_EVENT_GUID, @@ -270,7 +265,7 @@ static int __init msi_wmi_init(void) backlight->props.brightness = err; } - dprintk("Event handler installed\n"); + pr_debug("Event handler installed\n"); return 0; -- cgit v1.2.3 From 50f581a4f09f5b7f78a1c791e09b2c8d24a1e20c Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:48 -0700 Subject: sony-laptop: Add and use #define pr_fmt Add pr_fmt. Remove now unused #define DRV_PRX. Neaten dprintk macro. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/sony-laptop.c | 104 +++++++++++++++++-------------------- 1 file changed, 49 insertions(+), 55 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/sony-laptop.c b/drivers/platform/x86/sony-laptop.c index 6fe8cd6e23b..12dd0a62f30 100644 --- a/drivers/platform/x86/sony-laptop.c +++ b/drivers/platform/x86/sony-laptop.c @@ -42,6 +42,8 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -70,10 +72,10 @@ #include #endif -#define DRV_PFX "sony-laptop: " -#define dprintk(msg...) do { \ - if (debug) \ - pr_warn(DRV_PFX msg); \ +#define dprintk(fmt, ...) \ +do { \ + if (debug) \ + pr_warn(fmt, ##__VA_ARGS__); \ } while (0) #define SONY_LAPTOP_DRIVER_VERSION "0.6" @@ -418,7 +420,7 @@ static int sony_laptop_setup_input(struct acpi_device *acpi_device) error = kfifo_alloc(&sony_laptop_input.fifo, SONY_LAPTOP_BUF_SIZE, GFP_KERNEL); if (error) { - pr_err(DRV_PFX "kfifo_alloc failed\n"); + pr_err("kfifo_alloc failed\n"); goto err_dec_users; } @@ -702,7 +704,7 @@ static int acpi_callgetfunc(acpi_handle handle, char *name, int *result) return 0; } - pr_warn(DRV_PFX "acpi_callreadfunc failed\n"); + pr_warn("acpi_callreadfunc failed\n"); return -1; } @@ -728,8 +730,7 @@ static int acpi_callsetfunc(acpi_handle handle, char *name, int value, if (status == AE_OK) { if (result != NULL) { if (out_obj.type != ACPI_TYPE_INTEGER) { - pr_warn(DRV_PFX "acpi_evaluate_object bad " - "return type\n"); + pr_warn("acpi_evaluate_object bad return type\n"); return -1; } *result = out_obj.integer.value; @@ -737,7 +738,7 @@ static int acpi_callsetfunc(acpi_handle handle, char *name, int value, return 0; } - pr_warn(DRV_PFX "acpi_evaluate_object failed\n"); + pr_warn("acpi_evaluate_object failed\n"); return -1; } @@ -1104,10 +1105,8 @@ static void sony_nc_notify(struct acpi_device *device, u32 event) } if (!key_event->data) - pr_info(DRV_PFX - "Unknown event: 0x%x 0x%x\n", - key_handle, - ev); + pr_info("Unknown event: 0x%x 0x%x\n", + key_handle, ev); else sony_laptop_report_input_event(ev); } @@ -1128,7 +1127,7 @@ static acpi_status sony_walk_callback(acpi_handle handle, u32 level, struct acpi_device_info *info; if (ACPI_SUCCESS(acpi_get_object_info(handle, &info))) { - pr_warn(DRV_PFX "method: name: %4.4s, args %X\n", + pr_warn("method: name: %4.4s, args %X\n", (char *)&info->name, info->param_count); kfree(info); @@ -1169,7 +1168,7 @@ static int sony_nc_resume(struct acpi_device *device) ret = acpi_callsetfunc(sony_nc_acpi_handle, *item->acpiset, item->value, NULL); if (ret < 0) { - pr_err(DRV_PFX "%s: %d\n", __func__, ret); + pr_err("%s: %d\n", __func__, ret); break; } } @@ -1336,12 +1335,12 @@ static void sony_nc_rfkill_setup(struct acpi_device *device) device_enum = (union acpi_object *) buffer.pointer; if (!device_enum) { - pr_err(DRV_PFX "No SN06 return object."); + pr_err("No SN06 return object\n"); goto out_no_enum; } if (device_enum->type != ACPI_TYPE_BUFFER) { - pr_err(DRV_PFX "Invalid SN06 return object 0x%.2x\n", - device_enum->type); + pr_err("Invalid SN06 return object 0x%.2x\n", + device_enum->type); goto out_no_enum; } @@ -1662,7 +1661,7 @@ static void sony_nc_backlight_setup(void) ops, &props); if (IS_ERR(sony_bl_props.dev)) { - pr_warn(DRV_PFX "unable to register backlight device\n"); + pr_warn("unable to register backlight device\n"); sony_bl_props.dev = NULL; } else sony_bl_props.dev->props.brightness = @@ -1682,8 +1681,7 @@ static int sony_nc_add(struct acpi_device *device) acpi_handle handle; struct sony_nc_value *item; - pr_info(DRV_PFX "%s v%s.\n", SONY_NC_DRIVER_NAME, - SONY_LAPTOP_DRIVER_VERSION); + pr_info("%s v%s\n", SONY_NC_DRIVER_NAME, SONY_LAPTOP_DRIVER_VERSION); sony_nc_acpi_device = device; strcpy(acpi_device_class(device), "sony/hotkey"); @@ -1708,7 +1706,7 @@ static int sony_nc_add(struct acpi_device *device) sony_nc_acpi_handle, 1, sony_walk_callback, NULL, NULL, NULL); if (ACPI_FAILURE(status)) { - pr_warn(DRV_PFX "unable to walk acpi resources\n"); + pr_warn("unable to walk acpi resources\n"); result = -ENODEV; goto outpresent; } @@ -1736,13 +1734,12 @@ static int sony_nc_add(struct acpi_device *device) /* setup input devices and helper fifo */ result = sony_laptop_setup_input(device); if (result) { - pr_err(DRV_PFX "Unable to create input devices.\n"); + pr_err("Unable to create input devices\n"); goto outkbdbacklight; } if (acpi_video_backlight_support()) { - pr_info(DRV_PFX "brightness ignored, must be " - "controlled by ACPI video driver\n"); + pr_info("brightness ignored, must be controlled by ACPI video driver\n"); } else { sony_nc_backlight_setup(); } @@ -2265,9 +2262,9 @@ out: if (pcidev) pci_dev_put(pcidev); - pr_info(DRV_PFX "detected Type%d model\n", - dev->model == SONYPI_DEVICE_TYPE1 ? 1 : - dev->model == SONYPI_DEVICE_TYPE2 ? 2 : 3); + pr_info("detected Type%d model\n", + dev->model == SONYPI_DEVICE_TYPE1 ? 1 : + dev->model == SONYPI_DEVICE_TYPE2 ? 2 : 3); } /* camera tests and poweron/poweroff */ @@ -2313,7 +2310,7 @@ static int __sony_pic_camera_ready(void) static int __sony_pic_camera_off(void) { if (!camera) { - pr_warn(DRV_PFX "camera control not enabled\n"); + pr_warn("camera control not enabled\n"); return -ENODEV; } @@ -2333,7 +2330,7 @@ static int __sony_pic_camera_on(void) int i, j, x; if (!camera) { - pr_warn(DRV_PFX "camera control not enabled\n"); + pr_warn("camera control not enabled\n"); return -ENODEV; } @@ -2356,7 +2353,7 @@ static int __sony_pic_camera_on(void) } if (j == 0) { - pr_warn(DRV_PFX "failed to power on camera\n"); + pr_warn("failed to power on camera\n"); return -ENODEV; } @@ -2412,8 +2409,7 @@ int sony_pic_camera_command(int command, u8 value) ITERATIONS_SHORT); break; default: - pr_err(DRV_PFX "sony_pic_camera_command invalid: %d\n", - command); + pr_err("sony_pic_camera_command invalid: %d\n", command); break; } mutex_unlock(&spic_dev.lock); @@ -2819,7 +2815,7 @@ static int sonypi_compat_init(void) error = kfifo_alloc(&sonypi_compat.fifo, SONY_LAPTOP_BUF_SIZE, GFP_KERNEL); if (error) { - pr_err(DRV_PFX "kfifo_alloc failed\n"); + pr_err("kfifo_alloc failed\n"); return error; } @@ -2829,12 +2825,12 @@ static int sonypi_compat_init(void) sonypi_misc_device.minor = minor; error = misc_register(&sonypi_misc_device); if (error) { - pr_err(DRV_PFX "misc_register failed\n"); + pr_err("misc_register failed\n"); goto err_free_kfifo; } if (minor == -1) - pr_info(DRV_PFX "device allocated minor is %d\n", - sonypi_misc_device.minor); + pr_info("device allocated minor is %d\n", + sonypi_misc_device.minor); return 0; @@ -2893,8 +2889,8 @@ sony_pic_read_possible_resource(struct acpi_resource *resource, void *context) } for (i = 0; i < p->interrupt_count; i++) { if (!p->interrupts[i]) { - pr_warn(DRV_PFX "Invalid IRQ %d\n", - p->interrupts[i]); + pr_warn("Invalid IRQ %d\n", + p->interrupts[i]); continue; } interrupt = kzalloc(sizeof(*interrupt), @@ -2932,14 +2928,14 @@ sony_pic_read_possible_resource(struct acpi_resource *resource, void *context) ioport->io2.address_length); } else { - pr_err(DRV_PFX "Unknown SPIC Type, more than 2 IO Ports\n"); + pr_err("Unknown SPIC Type, more than 2 IO Ports\n"); return AE_ERROR; } return AE_OK; } default: dprintk("Resource %d isn't an IRQ nor an IO port\n", - resource->type); + resource->type); case ACPI_RESOURCE_TYPE_END_TAG: return AE_OK; @@ -2960,7 +2956,7 @@ static int sony_pic_possible_resources(struct acpi_device *device) dprintk("Evaluating _STA\n"); result = acpi_bus_get_status(device); if (result) { - pr_warn(DRV_PFX "Unable to read status\n"); + pr_warn("Unable to read status\n"); goto end; } @@ -2976,8 +2972,7 @@ static int sony_pic_possible_resources(struct acpi_device *device) status = acpi_walk_resources(device->handle, METHOD_NAME__PRS, sony_pic_read_possible_resource, &spic_dev); if (ACPI_FAILURE(status)) { - pr_warn(DRV_PFX "Failure evaluating %s\n", - METHOD_NAME__PRS); + pr_warn("Failure evaluating %s\n", METHOD_NAME__PRS); result = -ENODEV; } end: @@ -3090,7 +3085,7 @@ static int sony_pic_enable(struct acpi_device *device, /* check for total failure */ if (ACPI_FAILURE(status)) { - pr_err(DRV_PFX "Error evaluating _SRS\n"); + pr_err("Error evaluating _SRS\n"); result = -ENODEV; goto end; } @@ -3182,7 +3177,7 @@ static int sony_pic_remove(struct acpi_device *device, int type) struct sony_pic_irq *irq, *tmp_irq; if (sony_pic_disable(device)) { - pr_err(DRV_PFX "Couldn't disable device.\n"); + pr_err("Couldn't disable device\n"); return -ENXIO; } @@ -3222,8 +3217,7 @@ static int sony_pic_add(struct acpi_device *device) struct sony_pic_ioport *io, *tmp_io; struct sony_pic_irq *irq, *tmp_irq; - pr_info(DRV_PFX "%s v%s.\n", SONY_PIC_DRIVER_NAME, - SONY_LAPTOP_DRIVER_VERSION); + pr_info("%s v%s\n", SONY_PIC_DRIVER_NAME, SONY_LAPTOP_DRIVER_VERSION); spic_dev.acpi_dev = device; strcpy(acpi_device_class(device), "sony/hotkey"); @@ -3233,14 +3227,14 @@ static int sony_pic_add(struct acpi_device *device) /* read _PRS resources */ result = sony_pic_possible_resources(device); if (result) { - pr_err(DRV_PFX "Unable to read possible resources.\n"); + pr_err("Unable to read possible resources\n"); goto err_free_resources; } /* setup input devices and helper fifo */ result = sony_laptop_setup_input(device); if (result) { - pr_err(DRV_PFX "Unable to create input devices.\n"); + pr_err("Unable to create input devices\n"); goto err_free_resources; } @@ -3281,7 +3275,7 @@ static int sony_pic_add(struct acpi_device *device) } } if (!spic_dev.cur_ioport) { - pr_err(DRV_PFX "Failed to request_region.\n"); + pr_err("Failed to request_region\n"); result = -ENODEV; goto err_remove_compat; } @@ -3301,7 +3295,7 @@ static int sony_pic_add(struct acpi_device *device) } } if (!spic_dev.cur_irq) { - pr_err(DRV_PFX "Failed to request_irq.\n"); + pr_err("Failed to request_irq\n"); result = -ENODEV; goto err_release_region; } @@ -3309,7 +3303,7 @@ static int sony_pic_add(struct acpi_device *device) /* set resource status _SRS */ result = sony_pic_enable(device, spic_dev.cur_ioport, spic_dev.cur_irq); if (result) { - pr_err(DRV_PFX "Couldn't enable device.\n"); + pr_err("Couldn't enable device\n"); goto err_free_irq; } @@ -3418,7 +3412,7 @@ static int __init sony_laptop_init(void) if (!no_spic && dmi_check_system(sonypi_dmi_table)) { result = acpi_bus_register_driver(&sony_pic_driver); if (result) { - pr_err(DRV_PFX "Unable to register SPIC driver."); + pr_err("Unable to register SPIC driver\n"); goto out; } spic_drv_registered = 1; @@ -3426,7 +3420,7 @@ static int __init sony_laptop_init(void) result = acpi_bus_register_driver(&sony_nc_driver); if (result) { - pr_err(DRV_PFX "Unable to register SNC driver."); + pr_err("Unable to register SNC driver\n"); goto out_unregister_pic; } -- cgit v1.2.3 From 33cab1b71ec1bd02d55cede277bbc91485a68068 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:49 -0700 Subject: tc1100-wmi: Add pr_fmt, use pr_ Use the more normal logging styles. Removed now unused local logging #defines. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/tc1100-wmi.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/tc1100-wmi.c b/drivers/platform/x86/tc1100-wmi.c index 865ef78d6f1..e24f5ae475a 100644 --- a/drivers/platform/x86/tc1100-wmi.c +++ b/drivers/platform/x86/tc1100-wmi.c @@ -25,6 +25,8 @@ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -40,9 +42,6 @@ #define TC1100_INSTANCE_WIRELESS 1 #define TC1100_INSTANCE_JOGDIAL 2 -#define TC1100_LOGPREFIX "tc1100-wmi: " -#define TC1100_INFO KERN_INFO TC1100_LOGPREFIX - MODULE_AUTHOR("Jamey Hicks, Carlos Corbacho"); MODULE_DESCRIPTION("HP Compaq TC1100 Tablet WMI Extras"); MODULE_LICENSE("GPL"); @@ -264,7 +263,7 @@ static int __init tc1100_init(void) if (error) goto err_device_del; - printk(TC1100_INFO "HP Compaq TC1100 Tablet WMI Extras loaded\n"); + pr_info("HP Compaq TC1100 Tablet WMI Extras loaded\n"); return 0; err_device_del: -- cgit v1.2.3 From 93c1d05b5fa83ac771b5d1a5b4eb0fe6f54b3b46 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:51 -0700 Subject: topstar-laptop: Convert remaining printk to pr_info To be similar to all other uses. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/topstar-laptop.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/topstar-laptop.c b/drivers/platform/x86/topstar-laptop.c index 1d07d6d09f2..4c20447ddbb 100644 --- a/drivers/platform/x86/topstar-laptop.c +++ b/drivers/platform/x86/topstar-laptop.c @@ -194,7 +194,7 @@ static int __init topstar_laptop_init(void) if (ret < 0) return ret; - printk(KERN_INFO "Topstar Laptop ACPI extras driver loaded\n"); + pr_info("ACPI extras driver loaded\n"); return 0; } -- cgit v1.2.3 From 7e33460d8d991843a5821d667b55c75a092cf6e3 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:52 -0700 Subject: toshiba: Convert printks to pr_ Add pr_fmt. Remove local MY_ #defines. Convert printks to pr_. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/toshiba_acpi.c | 59 +++++++++++++++----------------- drivers/platform/x86/toshiba_bluetooth.c | 11 +++--- 2 files changed, 34 insertions(+), 36 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/toshiba_acpi.c b/drivers/platform/x86/toshiba_acpi.c index 63f42a22e10..cb009b2629e 100644 --- a/drivers/platform/x86/toshiba_acpi.c +++ b/drivers/platform/x86/toshiba_acpi.c @@ -35,6 +35,8 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #define TOSHIBA_ACPI_VERSION "0.19" #define PROC_INTERFACE_VERSION 1 @@ -60,11 +62,6 @@ MODULE_AUTHOR("John Belmonte"); MODULE_DESCRIPTION("Toshiba Laptop ACPI Extras Driver"); MODULE_LICENSE("GPL"); -#define MY_LOGPREFIX "toshiba_acpi: " -#define MY_ERR KERN_ERR MY_LOGPREFIX -#define MY_NOTICE KERN_NOTICE MY_LOGPREFIX -#define MY_INFO KERN_INFO MY_LOGPREFIX - /* Toshiba ACPI method paths */ #define METHOD_LCD_BRIGHTNESS "\\_SB_.PCI0.VGA_.LCD_._BCM" #define TOSH_INTERFACE_1 "\\_SB_.VALD" @@ -301,7 +298,7 @@ static int toshiba_illumination_available(void) in[0] = 0xf100; status = hci_raw(in, out); if (ACPI_FAILURE(status)) { - printk(MY_INFO "Illumination device not available\n"); + pr_info("Illumination device not available\n"); return 0; } in[0] = 0xf400; @@ -320,7 +317,7 @@ static void toshiba_illumination_set(struct led_classdev *cdev, in[0] = 0xf100; status = hci_raw(in, out); if (ACPI_FAILURE(status)) { - printk(MY_INFO "Illumination device not available\n"); + pr_info("Illumination device not available\n"); return; } @@ -331,7 +328,7 @@ static void toshiba_illumination_set(struct led_classdev *cdev, in[2] = 1; status = hci_raw(in, out); if (ACPI_FAILURE(status)) { - printk(MY_INFO "ACPI call for illumination failed.\n"); + pr_info("ACPI call for illumination failed\n"); return; } } else { @@ -341,7 +338,7 @@ static void toshiba_illumination_set(struct led_classdev *cdev, in[2] = 0; status = hci_raw(in, out); if (ACPI_FAILURE(status)) { - printk(MY_INFO "ACPI call for illumination failed.\n"); + pr_info("ACPI call for illumination failed.\n"); return; } } @@ -364,7 +361,7 @@ static enum led_brightness toshiba_illumination_get(struct led_classdev *cdev) in[0] = 0xf100; status = hci_raw(in, out); if (ACPI_FAILURE(status)) { - printk(MY_INFO "Illumination device not available\n"); + pr_info("Illumination device not available\n"); return LED_OFF; } @@ -373,7 +370,7 @@ static enum led_brightness toshiba_illumination_get(struct led_classdev *cdev) in[1] = 0x14e; status = hci_raw(in, out); if (ACPI_FAILURE(status)) { - printk(MY_INFO "ACPI call for illumination failed.\n"); + pr_info("ACPI call for illumination failed.\n"); return LED_OFF; } @@ -517,7 +514,7 @@ static int lcd_proc_show(struct seq_file *m, void *v) seq_printf(m, "brightness_levels: %d\n", HCI_LCD_BRIGHTNESS_LEVELS); } else { - printk(MY_ERR "Error reading LCD brightness\n"); + pr_err("Error reading LCD brightness\n"); } return 0; @@ -592,7 +589,7 @@ static int video_proc_show(struct seq_file *m, void *v) seq_printf(m, "crt_out: %d\n", is_crt); seq_printf(m, "tv_out: %d\n", is_tv); } else { - printk(MY_ERR "Error reading video out status\n"); + pr_err("Error reading video out status\n"); } return 0; @@ -686,7 +683,7 @@ static int fan_proc_show(struct seq_file *m, void *v) seq_printf(m, "running: %d\n", (value > 0)); seq_printf(m, "force_on: %d\n", force_fan); } else { - printk(MY_ERR "Error reading fan status\n"); + pr_err("Error reading fan status\n"); } return 0; @@ -750,9 +747,9 @@ static int keys_proc_show(struct seq_file *m, void *v) * some machines where system events sporadically * become disabled. */ hci_write1(HCI_SYSTEM_EVENT, 1, &hci_result); - printk(MY_NOTICE "Re-enabled hotkeys\n"); + pr_notice("Re-enabled hotkeys\n"); } else { - printk(MY_ERR "Error reading hotkey status\n"); + pr_err("Error reading hotkey status\n"); goto end; } } @@ -863,7 +860,7 @@ static void toshiba_acpi_notify(acpi_handle handle, u32 event, void *context) if (!sparse_keymap_report_event(toshiba_acpi.hotkey_dev, value, 1, true)) { - printk(MY_INFO "Unknown key %x\n", + pr_info("Unknown key %x\n", value); } } else if (hci_result == HCI_NOT_SUPPORTED) { @@ -871,7 +868,7 @@ static void toshiba_acpi_notify(acpi_handle handle, u32 event, void *context) * some machines where system events sporadically * become disabled. */ hci_write1(HCI_SYSTEM_EVENT, 1, &hci_result); - printk(MY_NOTICE "Re-enabled hotkeys\n"); + pr_notice("Re-enabled hotkeys\n"); } } while (hci_result != HCI_EMPTY); } @@ -883,13 +880,13 @@ static int __init toshiba_acpi_setup_keyboard(char *device) status = acpi_get_handle(NULL, device, &toshiba_acpi.handle); if (ACPI_FAILURE(status)) { - printk(MY_INFO "Unable to get notification device\n"); + pr_info("Unable to get notification device\n"); return -ENODEV; } toshiba_acpi.hotkey_dev = input_allocate_device(); if (!toshiba_acpi.hotkey_dev) { - printk(MY_INFO "Unable to register input device\n"); + pr_info("Unable to register input device\n"); return -ENOMEM; } @@ -905,21 +902,21 @@ static int __init toshiba_acpi_setup_keyboard(char *device) status = acpi_install_notify_handler(toshiba_acpi.handle, ACPI_DEVICE_NOTIFY, toshiba_acpi_notify, NULL); if (ACPI_FAILURE(status)) { - printk(MY_INFO "Unable to install hotkey notification\n"); + pr_info("Unable to install hotkey notification\n"); error = -ENODEV; goto err_free_keymap; } status = acpi_evaluate_object(toshiba_acpi.handle, "ENAB", NULL, NULL); if (ACPI_FAILURE(status)) { - printk(MY_INFO "Unable to enable hotkeys\n"); + pr_info("Unable to enable hotkeys\n"); error = -ENODEV; goto err_remove_notify; } error = input_register_device(toshiba_acpi.hotkey_dev); if (error) { - printk(MY_INFO "Unable to register input device\n"); + pr_info("Unable to register input device\n"); goto err_remove_notify; } @@ -980,17 +977,17 @@ static int __init toshiba_acpi_init(void) if (is_valid_acpi_path(TOSH_INTERFACE_1 GHCI_METHOD)) { method_hci = TOSH_INTERFACE_1 GHCI_METHOD; if (toshiba_acpi_setup_keyboard(TOSH_INTERFACE_1)) - printk(MY_INFO "Unable to activate hotkeys\n"); + pr_info("Unable to activate hotkeys\n"); } else if (is_valid_acpi_path(TOSH_INTERFACE_2 GHCI_METHOD)) { method_hci = TOSH_INTERFACE_2 GHCI_METHOD; if (toshiba_acpi_setup_keyboard(TOSH_INTERFACE_2)) - printk(MY_INFO "Unable to activate hotkeys\n"); + pr_info("Unable to activate hotkeys\n"); } else return -ENODEV; - printk(MY_INFO "Toshiba Laptop ACPI Extras version %s\n", + pr_info("Toshiba Laptop ACPI Extras version %s\n", TOSHIBA_ACPI_VERSION); - printk(MY_INFO " HCI method: %s\n", method_hci); + pr_info(" HCI method: %s\n", method_hci); mutex_init(&toshiba_acpi.mutex); @@ -998,7 +995,7 @@ static int __init toshiba_acpi_init(void) -1, NULL, 0); if (IS_ERR(toshiba_acpi.p_dev)) { ret = PTR_ERR(toshiba_acpi.p_dev); - printk(MY_ERR "unable to register platform device\n"); + pr_err("unable to register platform device\n"); toshiba_acpi.p_dev = NULL; toshiba_acpi_exit(); return ret; @@ -1028,7 +1025,7 @@ static int __init toshiba_acpi_init(void) if (IS_ERR(toshiba_backlight_device)) { ret = PTR_ERR(toshiba_backlight_device); - printk(KERN_ERR "Could not register toshiba backlight device\n"); + pr_err("Could not register toshiba backlight device\n"); toshiba_backlight_device = NULL; toshiba_acpi_exit(); return ret; @@ -1042,14 +1039,14 @@ static int __init toshiba_acpi_init(void) &toshiba_rfk_ops, &toshiba_acpi); if (!toshiba_acpi.bt_rfk) { - printk(MY_ERR "unable to allocate rfkill device\n"); + pr_err("unable to allocate rfkill device\n"); toshiba_acpi_exit(); return -ENOMEM; } ret = rfkill_register(toshiba_acpi.bt_rfk); if (ret) { - printk(MY_ERR "unable to register rfkill device\n"); + pr_err("unable to register rfkill device\n"); rfkill_destroy(toshiba_acpi.bt_rfk); toshiba_acpi_exit(); return ret; diff --git a/drivers/platform/x86/toshiba_bluetooth.c b/drivers/platform/x86/toshiba_bluetooth.c index 94406861191..5fb7186694d 100644 --- a/drivers/platform/x86/toshiba_bluetooth.c +++ b/drivers/platform/x86/toshiba_bluetooth.c @@ -17,6 +17,8 @@ * delivered. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -70,14 +72,13 @@ static int toshiba_bluetooth_enable(acpi_handle handle) if (!(result & 0x01)) return 0; - printk(KERN_INFO "toshiba_bluetooth: Re-enabling Toshiba Bluetooth\n"); + pr_info("Re-enabling Toshiba Bluetooth\n"); res1 = acpi_evaluate_object(handle, "AUSB", NULL, NULL); res2 = acpi_evaluate_object(handle, "BTPO", NULL, NULL); if (!ACPI_FAILURE(res1) || !ACPI_FAILURE(res2)) return 0; - printk(KERN_WARNING "toshiba_bluetooth: Failed to re-enable " - "Toshiba Bluetooth\n"); + pr_warn("Failed to re-enable Toshiba Bluetooth\n"); return -ENODEV; } @@ -107,8 +108,8 @@ static int toshiba_bt_rfkill_add(struct acpi_device *device) &bt_present); if (!ACPI_FAILURE(status) && bt_present) { - printk(KERN_INFO "Detected Toshiba ACPI Bluetooth device - " - "installing RFKill handler\n"); + pr_info("Detected Toshiba ACPI Bluetooth device - " + "installing RFKill handler\n"); result = toshiba_bluetooth_enable(device->handle); } -- cgit v1.2.3 From dd8e908e82964b8b493ef241707fb6109aa41cfd Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:53 -0700 Subject: wmi: Removed trailing whitespace from logging message. Just neatening. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/wmi.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/wmi.c b/drivers/platform/x86/wmi.c index 05cc79672a8..f23d5a84e7b 100644 --- a/drivers/platform/x86/wmi.c +++ b/drivers/platform/x86/wmi.c @@ -486,16 +486,16 @@ static void wmi_dump_wdg(const struct guid_block *g) pr_info("\tnotify_id: %02X\n", g->notify_id); pr_info("\treserved: %02X\n", g->reserved); pr_info("\tinstance_count: %d\n", g->instance_count); - pr_info("\tflags: %#x ", g->flags); + pr_info("\tflags: %#x", g->flags); if (g->flags) { if (g->flags & ACPI_WMI_EXPENSIVE) - pr_cont("ACPI_WMI_EXPENSIVE "); + pr_cont(" ACPI_WMI_EXPENSIVE"); if (g->flags & ACPI_WMI_METHOD) - pr_cont("ACPI_WMI_METHOD "); + pr_cont(" ACPI_WMI_METHOD"); if (g->flags & ACPI_WMI_STRING) - pr_cont("ACPI_WMI_STRING "); + pr_cont(" ACPI_WMI_STRING"); if (g->flags & ACPI_WMI_EVENT) - pr_cont("ACPI_WMI_EVENT "); + pr_cont(" ACPI_WMI_EVENT"); } pr_cont("\n"); -- cgit v1.2.3 From ad3f2f038fbd67f3341f760507aed90381114145 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 29 Mar 2011 15:21:54 -0700 Subject: xo15-ebook: Use pr_ Use the current logging styles. Remove local #define PREFIX. Add pr_fmt. Convert printk to pr_. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/xo15-ebook.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/xo15-ebook.c b/drivers/platform/x86/xo15-ebook.c index c1372ed9d2e..fad153dc035 100644 --- a/drivers/platform/x86/xo15-ebook.c +++ b/drivers/platform/x86/xo15-ebook.c @@ -11,6 +11,8 @@ * your option) any later version. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -20,7 +22,6 @@ #include #define MODULE_NAME "xo15-ebook" -#define PREFIX MODULE_NAME ": " #define XO15_EBOOK_CLASS MODULE_NAME #define XO15_EBOOK_TYPE_UNKNOWN 0x00 @@ -105,7 +106,7 @@ static int ebook_switch_add(struct acpi_device *device) class = acpi_device_class(device); if (strcmp(hid, XO15_EBOOK_HID)) { - printk(KERN_ERR PREFIX "Unsupported hid [%s]\n", hid); + pr_err("Unsupported hid [%s]\n", hid); error = -ENODEV; goto err_free_input; } -- cgit v1.2.3 From 253a0069d7a222f7ad55f2c40f541a7648920c77 Mon Sep 17 00:00:00 2001 From: Ameya Palande Date: Fri, 1 Apr 2011 16:54:11 +0300 Subject: platform-x86: intel_mid_thermal: Fix coding style Before fixing checkpatch.pl reported 74 errors and 234 warnings Signed-off-by: Ameya Palande Signed-off-by: Matthew Garrett --- drivers/platform/x86/intel_mid_thermal.c | 606 +++++++++++++++---------------- 1 file changed, 300 insertions(+), 306 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/intel_mid_thermal.c b/drivers/platform/x86/intel_mid_thermal.c index c2f4bd8013b..f0776504521 100644 --- a/drivers/platform/x86/intel_mid_thermal.c +++ b/drivers/platform/x86/intel_mid_thermal.c @@ -37,49 +37,50 @@ #include /* Number of thermal sensors */ -#define MSIC_THERMAL_SENSORS 4 +#define MSIC_THERMAL_SENSORS 4 /* ADC1 - thermal registers */ -#define MSIC_THERM_ADC1CNTL1 0x1C0 -#define MSIC_ADC_ENBL 0x10 -#define MSIC_ADC_START 0x08 +#define MSIC_THERM_ADC1CNTL1 0x1C0 +#define MSIC_ADC_ENBL 0x10 +#define MSIC_ADC_START 0x08 -#define MSIC_THERM_ADC1CNTL3 0x1C2 -#define MSIC_ADCTHERM_ENBL 0x04 -#define MSIC_ADCRRDATA_ENBL 0x05 -#define MSIC_CHANL_MASK_VAL 0x0F +#define MSIC_THERM_ADC1CNTL3 0x1C2 +#define MSIC_ADCTHERM_ENBL 0x04 +#define MSIC_ADCRRDATA_ENBL 0x05 +#define MSIC_CHANL_MASK_VAL 0x0F -#define MSIC_STOPBIT_MASK 16 -#define MSIC_ADCTHERM_MASK 4 -#define ADC_CHANLS_MAX 15 /* Number of ADC channels */ -#define ADC_LOOP_MAX (ADC_CHANLS_MAX - MSIC_THERMAL_SENSORS) +#define MSIC_STOPBIT_MASK 16 +#define MSIC_ADCTHERM_MASK 4 +/* Number of ADC channels */ +#define ADC_CHANLS_MAX 15 +#define ADC_LOOP_MAX (ADC_CHANLS_MAX - MSIC_THERMAL_SENSORS) /* ADC channel code values */ -#define SKIN_SENSOR0_CODE 0x08 -#define SKIN_SENSOR1_CODE 0x09 -#define SYS_SENSOR_CODE 0x0A -#define MSIC_DIE_SENSOR_CODE 0x03 +#define SKIN_SENSOR0_CODE 0x08 +#define SKIN_SENSOR1_CODE 0x09 +#define SYS_SENSOR_CODE 0x0A +#define MSIC_DIE_SENSOR_CODE 0x03 -#define SKIN_THERM_SENSOR0 0 -#define SKIN_THERM_SENSOR1 1 -#define SYS_THERM_SENSOR2 2 -#define MSIC_DIE_THERM_SENSOR3 3 +#define SKIN_THERM_SENSOR0 0 +#define SKIN_THERM_SENSOR1 1 +#define SYS_THERM_SENSOR2 2 +#define MSIC_DIE_THERM_SENSOR3 3 /* ADC code range */ -#define ADC_MAX 977 -#define ADC_MIN 162 -#define ADC_VAL0C 887 -#define ADC_VAL20C 720 -#define ADC_VAL40C 508 -#define ADC_VAL60C 315 +#define ADC_MAX 977 +#define ADC_MIN 162 +#define ADC_VAL0C 887 +#define ADC_VAL20C 720 +#define ADC_VAL40C 508 +#define ADC_VAL60C 315 /* ADC base addresses */ -#define ADC_CHNL_START_ADDR 0x1C5 /* increments by 1 */ -#define ADC_DATA_START_ADDR 0x1D4 /* increments by 2 */ +#define ADC_CHNL_START_ADDR 0x1C5 /* increments by 1 */ +#define ADC_DATA_START_ADDR 0x1D4 /* increments by 2 */ /* MSIC die attributes */ -#define MSIC_DIE_ADC_MIN 488 -#define MSIC_DIE_ADC_MAX 1004 +#define MSIC_DIE_ADC_MIN 488 +#define MSIC_DIE_ADC_MAX 1004 /* This holds the address of the first free ADC channel, * among the 15 channels @@ -87,15 +88,15 @@ static int channel_index; struct platform_info { - struct platform_device *pdev; - struct thermal_zone_device *tzd[MSIC_THERMAL_SENSORS]; + struct platform_device *pdev; + struct thermal_zone_device *tzd[MSIC_THERMAL_SENSORS]; }; struct thermal_device_info { - unsigned int chnl_addr; - int direct; - /* This holds the current temperature in millidegree celsius */ - long curr_temp; + unsigned int chnl_addr; + int direct; + /* This holds the current temperature in millidegree celsius */ + long curr_temp; }; /** @@ -106,7 +107,7 @@ struct thermal_device_info { */ static int to_msic_die_temp(uint16_t adc_val) { - return (368 * (adc_val) / 1000) - 220; + return (368 * (adc_val) / 1000) - 220; } /** @@ -118,7 +119,7 @@ static int to_msic_die_temp(uint16_t adc_val) */ static int is_valid_adc(uint16_t adc_val, uint16_t min, uint16_t max) { - return (adc_val >= min) && (adc_val <= max); + return (adc_val >= min) && (adc_val <= max); } /** @@ -136,35 +137,35 @@ static int is_valid_adc(uint16_t adc_val, uint16_t min, uint16_t max) */ static int adc_to_temp(int direct, uint16_t adc_val, unsigned long *tp) { - int temp; - - /* Direct conversion for die temperature */ - if (direct) { - if (is_valid_adc(adc_val, MSIC_DIE_ADC_MIN, MSIC_DIE_ADC_MAX)) { - *tp = to_msic_die_temp(adc_val) * 1000; - return 0; - } - return -ERANGE; - } - - if (!is_valid_adc(adc_val, ADC_MIN, ADC_MAX)) - return -ERANGE; - - /* Linear approximation for skin temperature */ - if (adc_val > ADC_VAL0C) - temp = 177 - (adc_val/5); - else if ((adc_val <= ADC_VAL0C) && (adc_val > ADC_VAL20C)) - temp = 111 - (adc_val/8); - else if ((adc_val <= ADC_VAL20C) && (adc_val > ADC_VAL40C)) - temp = 92 - (adc_val/10); - else if ((adc_val <= ADC_VAL40C) && (adc_val > ADC_VAL60C)) - temp = 91 - (adc_val/10); - else - temp = 112 - (adc_val/6); - - /* Convert temperature in celsius to milli degree celsius */ - *tp = temp * 1000; - return 0; + int temp; + + /* Direct conversion for die temperature */ + if (direct) { + if (is_valid_adc(adc_val, MSIC_DIE_ADC_MIN, MSIC_DIE_ADC_MAX)) { + *tp = to_msic_die_temp(adc_val) * 1000; + return 0; + } + return -ERANGE; + } + + if (!is_valid_adc(adc_val, ADC_MIN, ADC_MAX)) + return -ERANGE; + + /* Linear approximation for skin temperature */ + if (adc_val > ADC_VAL0C) + temp = 177 - (adc_val/5); + else if ((adc_val <= ADC_VAL0C) && (adc_val > ADC_VAL20C)) + temp = 111 - (adc_val/8); + else if ((adc_val <= ADC_VAL20C) && (adc_val > ADC_VAL40C)) + temp = 92 - (adc_val/10); + else if ((adc_val <= ADC_VAL40C) && (adc_val > ADC_VAL60C)) + temp = 91 - (adc_val/10); + else + temp = 112 - (adc_val/6); + + /* Convert temperature in celsius to milli degree celsius */ + *tp = temp * 1000; + return 0; } /** @@ -178,47 +179,47 @@ static int adc_to_temp(int direct, uint16_t adc_val, unsigned long *tp) */ static int mid_read_temp(struct thermal_zone_device *tzd, unsigned long *temp) { - struct thermal_device_info *td_info = tzd->devdata; - uint16_t adc_val, addr; - uint8_t data = 0; - int ret; - unsigned long curr_temp; - - - addr = td_info->chnl_addr; - - /* Enable the msic for conversion before reading */ - ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCRRDATA_ENBL); - if (ret) - return ret; - - /* Re-toggle the RRDATARD bit (temporary workaround) */ - ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCTHERM_ENBL); - if (ret) - return ret; - - /* Read the higher bits of data */ - ret = intel_scu_ipc_ioread8(addr, &data); - if (ret) - return ret; - - /* Shift bits to accommodate the lower two data bits */ - adc_val = (data << 2); - addr++; - - ret = intel_scu_ipc_ioread8(addr, &data);/* Read lower bits */ - if (ret) - return ret; - - /* Adding lower two bits to the higher bits */ - data &= 03; - adc_val += data; - - /* Convert ADC value to temperature */ - ret = adc_to_temp(td_info->direct, adc_val, &curr_temp); - if (ret == 0) - *temp = td_info->curr_temp = curr_temp; - return ret; + struct thermal_device_info *td_info = tzd->devdata; + uint16_t adc_val, addr; + uint8_t data = 0; + int ret; + unsigned long curr_temp; + + + addr = td_info->chnl_addr; + + /* Enable the msic for conversion before reading */ + ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCRRDATA_ENBL); + if (ret) + return ret; + + /* Re-toggle the RRDATARD bit (temporary workaround) */ + ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCTHERM_ENBL); + if (ret) + return ret; + + /* Read the higher bits of data */ + ret = intel_scu_ipc_ioread8(addr, &data); + if (ret) + return ret; + + /* Shift bits to accommodate the lower two data bits */ + adc_val = (data << 2); + addr++; + + ret = intel_scu_ipc_ioread8(addr, &data);/* Read lower bits */ + if (ret) + return ret; + + /* Adding lower two bits to the higher bits */ + data &= 03; + adc_val += data; + + /* Convert ADC value to temperature */ + ret = adc_to_temp(td_info->direct, adc_val, &curr_temp); + if (ret == 0) + *temp = td_info->curr_temp = curr_temp; + return ret; } /** @@ -231,22 +232,21 @@ static int mid_read_temp(struct thermal_zone_device *tzd, unsigned long *temp) */ static int configure_adc(int val) { - int ret; - uint8_t data; - - ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data); - if (ret) - return ret; - - if (val) { - /* Enable and start the ADC */ - data |= (MSIC_ADC_ENBL | MSIC_ADC_START); - } else { - /* Just stop the ADC */ - data &= (~MSIC_ADC_START); - } - - return intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL1, data); + int ret; + uint8_t data; + + ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data); + if (ret) + return ret; + + if (val) { + /* Enable and start the ADC */ + data |= (MSIC_ADC_ENBL | MSIC_ADC_START); + } else { + /* Just stop the ADC */ + data &= (~MSIC_ADC_START); + } + return intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL1, data); } /** @@ -259,30 +259,30 @@ static int configure_adc(int val) */ static int set_up_therm_channel(u16 base_addr) { - int ret; - - /* Enable all the sensor channels */ - ret = intel_scu_ipc_iowrite8(base_addr, SKIN_SENSOR0_CODE); - if (ret) - return ret; - - ret = intel_scu_ipc_iowrite8(base_addr + 1, SKIN_SENSOR1_CODE); - if (ret) - return ret; - - ret = intel_scu_ipc_iowrite8(base_addr + 2, SYS_SENSOR_CODE); - if (ret) - return ret; - - /* Since this is the last channel, set the stop bit - to 1 by ORing the DIE_SENSOR_CODE with 0x10 */ - ret = intel_scu_ipc_iowrite8(base_addr + 3, - (MSIC_DIE_SENSOR_CODE | 0x10)); - if (ret) - return ret; - - /* Enable ADC and start it */ - return configure_adc(1); + int ret; + + /* Enable all the sensor channels */ + ret = intel_scu_ipc_iowrite8(base_addr, SKIN_SENSOR0_CODE); + if (ret) + return ret; + + ret = intel_scu_ipc_iowrite8(base_addr + 1, SKIN_SENSOR1_CODE); + if (ret) + return ret; + + ret = intel_scu_ipc_iowrite8(base_addr + 2, SYS_SENSOR_CODE); + if (ret) + return ret; + + /* Since this is the last channel, set the stop bit + * to 1 by ORing the DIE_SENSOR_CODE with 0x10 */ + ret = intel_scu_ipc_iowrite8(base_addr + 3, + (MSIC_DIE_SENSOR_CODE | 0x10)); + if (ret) + return ret; + + /* Enable ADC and start it */ + return configure_adc(1); } /** @@ -293,13 +293,13 @@ static int set_up_therm_channel(u16 base_addr) */ static int reset_stopbit(uint16_t addr) { - int ret; - uint8_t data; - ret = intel_scu_ipc_ioread8(addr, &data); - if (ret) - return ret; - /* Set the stop bit to zero */ - return intel_scu_ipc_iowrite8(addr, (data & 0xEF)); + int ret; + uint8_t data; + ret = intel_scu_ipc_ioread8(addr, &data); + if (ret) + return ret; + /* Set the stop bit to zero */ + return intel_scu_ipc_iowrite8(addr, (data & 0xEF)); } /** @@ -317,30 +317,30 @@ static int reset_stopbit(uint16_t addr) */ static int find_free_channel(void) { - int ret; - int i; - uint8_t data; - - /* check whether ADC is enabled */ - ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data); - if (ret) - return ret; - - if ((data & MSIC_ADC_ENBL) == 0) - return 0; - - /* ADC is already enabled; Looking for an empty channel */ - for (i = 0; i < ADC_CHANLS_MAX; i++) { - ret = intel_scu_ipc_ioread8(ADC_CHNL_START_ADDR + i, &data); - if (ret) - return ret; - - if (data & MSIC_STOPBIT_MASK) { - ret = i; - break; - } - } - return (ret > ADC_LOOP_MAX) ? (-EINVAL) : ret; + int ret; + int i; + uint8_t data; + + /* check whether ADC is enabled */ + ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data); + if (ret) + return ret; + + if ((data & MSIC_ADC_ENBL) == 0) + return 0; + + /* ADC is already enabled; Looking for an empty channel */ + for (i = 0; i < ADC_CHANLS_MAX; i++) { + ret = intel_scu_ipc_ioread8(ADC_CHNL_START_ADDR + i, &data); + if (ret) + return ret; + + if (data & MSIC_STOPBIT_MASK) { + ret = i; + break; + } + } + return (ret > ADC_LOOP_MAX) ? (-EINVAL) : ret; } /** @@ -351,48 +351,48 @@ static int find_free_channel(void) */ static int mid_initialize_adc(struct device *dev) { - u8 data; - u16 base_addr; - int ret; - - /* - * Ensure that adctherm is disabled before we - * initialize the ADC - */ - ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL3, &data); - if (ret) - return ret; - - if (data & MSIC_ADCTHERM_MASK) - dev_warn(dev, "ADCTHERM already set"); - - /* Index of the first channel in which the stop bit is set */ - channel_index = find_free_channel(); - if (channel_index < 0) { - dev_err(dev, "No free ADC channels"); - return channel_index; - } - - base_addr = ADC_CHNL_START_ADDR + channel_index; - - if (!(channel_index == 0 || channel_index == ADC_LOOP_MAX)) { - /* Reset stop bit for channels other than 0 and 12 */ - ret = reset_stopbit(base_addr); - if (ret) - return ret; - - /* Index of the first free channel */ - base_addr++; - channel_index++; - } - - ret = set_up_therm_channel(base_addr); - if (ret) { - dev_err(dev, "unable to enable ADC"); - return ret; - } - dev_dbg(dev, "ADC initialization successful"); - return ret; + u8 data; + u16 base_addr; + int ret; + + /* + * Ensure that adctherm is disabled before we + * initialize the ADC + */ + ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL3, &data); + if (ret) + return ret; + + if (data & MSIC_ADCTHERM_MASK) + dev_warn(dev, "ADCTHERM already set"); + + /* Index of the first channel in which the stop bit is set */ + channel_index = find_free_channel(); + if (channel_index < 0) { + dev_err(dev, "No free ADC channels"); + return channel_index; + } + + base_addr = ADC_CHNL_START_ADDR + channel_index; + + if (!(channel_index == 0 || channel_index == ADC_LOOP_MAX)) { + /* Reset stop bit for channels other than 0 and 12 */ + ret = reset_stopbit(base_addr); + if (ret) + return ret; + + /* Index of the first free channel */ + base_addr++; + channel_index++; + } + + ret = set_up_therm_channel(base_addr); + if (ret) { + dev_err(dev, "unable to enable ADC"); + return ret; + } + dev_dbg(dev, "ADC initialization successful"); + return ret; } /** @@ -403,18 +403,18 @@ static int mid_initialize_adc(struct device *dev) */ static struct thermal_device_info *initialize_sensor(int index) { - struct thermal_device_info *td_info = - kzalloc(sizeof(struct thermal_device_info), GFP_KERNEL); - - if (!td_info) - return NULL; - - /* Set the base addr of the channel for this sensor */ - td_info->chnl_addr = ADC_DATA_START_ADDR + 2 * (channel_index + index); - /* Sensor 3 is direct conversion */ - if (index == 3) - td_info->direct = 1; - return td_info; + struct thermal_device_info *td_info = + kzalloc(sizeof(struct thermal_device_info), GFP_KERNEL); + + if (!td_info) + return NULL; + + /* Set the base addr of the channel for this sensor */ + td_info->chnl_addr = ADC_DATA_START_ADDR + 2 * (channel_index + index); + /* Sensor 3 is direct conversion */ + if (index == 3) + td_info->direct = 1; + return td_info; } /** @@ -425,7 +425,7 @@ static struct thermal_device_info *initialize_sensor(int index) */ static int mid_thermal_resume(struct platform_device *pdev) { - return mid_initialize_adc(&pdev->dev); + return mid_initialize_adc(&pdev->dev); } /** @@ -437,12 +437,12 @@ static int mid_thermal_resume(struct platform_device *pdev) */ static int mid_thermal_suspend(struct platform_device *pdev, pm_message_t mesg) { - /* - * This just stops the ADC and does not disable it. - * temporary workaround until we have a generic ADC driver. - * If 0 is passed, it disables the ADC. - */ - return configure_adc(0); + /* + * This just stops the ADC and does not disable it. + * temporary workaround until we have a generic ADC driver. + * If 0 is passed, it disables the ADC. + */ + return configure_adc(0); } /** @@ -453,16 +453,15 @@ static int mid_thermal_suspend(struct platform_device *pdev, pm_message_t mesg) */ static int read_curr_temp(struct thermal_zone_device *tzd, unsigned long *temp) { - WARN_ON(tzd == NULL); - return mid_read_temp(tzd, temp); + WARN_ON(tzd == NULL); + return mid_read_temp(tzd, temp); } /* Can't be const */ static struct thermal_zone_device_ops tzd_ops = { - .get_temp = read_curr_temp, + .get_temp = read_curr_temp, }; - /** * mid_thermal_probe - mfld thermal initialize * @pdev: platform device structure @@ -472,46 +471,45 @@ static struct thermal_zone_device_ops tzd_ops = { */ static int mid_thermal_probe(struct platform_device *pdev) { - static char *name[MSIC_THERMAL_SENSORS] = { - "skin0", "skin1", "sys", "msicdie" - }; - - int ret; - int i; - struct platform_info *pinfo; - - pinfo = kzalloc(sizeof(struct platform_info), GFP_KERNEL); - if (!pinfo) - return -ENOMEM; - - /* Initializing the hardware */ - ret = mid_initialize_adc(&pdev->dev); - if (ret) { - dev_err(&pdev->dev, "ADC init failed"); - kfree(pinfo); - return ret; - } - - /* Register each sensor with the generic thermal framework*/ - for (i = 0; i < MSIC_THERMAL_SENSORS; i++) { - pinfo->tzd[i] = thermal_zone_device_register(name[i], - 0, initialize_sensor(i), - &tzd_ops, 0, 0, 0, 0); - if (IS_ERR(pinfo->tzd[i])) - goto reg_fail; - } - - pinfo->pdev = pdev; - platform_set_drvdata(pdev, pinfo); - return 0; + static char *name[MSIC_THERMAL_SENSORS] = { + "skin0", "skin1", "sys", "msicdie" + }; + + int ret; + int i; + struct platform_info *pinfo; + + pinfo = kzalloc(sizeof(struct platform_info), GFP_KERNEL); + if (!pinfo) + return -ENOMEM; + + /* Initializing the hardware */ + ret = mid_initialize_adc(&pdev->dev); + if (ret) { + dev_err(&pdev->dev, "ADC init failed"); + kfree(pinfo); + return ret; + } + + /* Register each sensor with the generic thermal framework*/ + for (i = 0; i < MSIC_THERMAL_SENSORS; i++) { + pinfo->tzd[i] = thermal_zone_device_register(name[i], + 0, initialize_sensor(i), &tzd_ops, 0, 0, 0, 0); + if (IS_ERR(pinfo->tzd[i])) + goto reg_fail; + } + + pinfo->pdev = pdev; + platform_set_drvdata(pdev, pinfo); + return 0; reg_fail: - ret = PTR_ERR(pinfo->tzd[i]); - while (--i >= 0) - thermal_zone_device_unregister(pinfo->tzd[i]); - configure_adc(0); - kfree(pinfo); - return ret; + ret = PTR_ERR(pinfo->tzd[i]); + while (--i >= 0) + thermal_zone_device_unregister(pinfo->tzd[i]); + configure_adc(0); + kfree(pinfo); + return ret; } /** @@ -523,49 +521,45 @@ reg_fail: */ static int mid_thermal_remove(struct platform_device *pdev) { - int i; - struct platform_info *pinfo = platform_get_drvdata(pdev); + int i; + struct platform_info *pinfo = platform_get_drvdata(pdev); - for (i = 0; i < MSIC_THERMAL_SENSORS; i++) - thermal_zone_device_unregister(pinfo->tzd[i]); + for (i = 0; i < MSIC_THERMAL_SENSORS; i++) + thermal_zone_device_unregister(pinfo->tzd[i]); - platform_set_drvdata(pdev, NULL); + platform_set_drvdata(pdev, NULL); - /* Stop the ADC */ - return configure_adc(0); + /* Stop the ADC */ + return configure_adc(0); } -/********************************************************************* - * Driver initialisation and finalization - *********************************************************************/ - #define DRIVER_NAME "msic_sensor" static const struct platform_device_id therm_id_table[] = { - { DRIVER_NAME, 1 }, - { } + { DRIVER_NAME, 1 }, + { } }; static struct platform_driver mid_thermal_driver = { - .driver = { - .name = DRIVER_NAME, - .owner = THIS_MODULE, - }, - .probe = mid_thermal_probe, - .suspend = mid_thermal_suspend, - .resume = mid_thermal_resume, - .remove = __devexit_p(mid_thermal_remove), - .id_table = therm_id_table, + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + }, + .probe = mid_thermal_probe, + .suspend = mid_thermal_suspend, + .resume = mid_thermal_resume, + .remove = __devexit_p(mid_thermal_remove), + .id_table = therm_id_table, }; static int __init mid_thermal_module_init(void) { - return platform_driver_register(&mid_thermal_driver); + return platform_driver_register(&mid_thermal_driver); } static void __exit mid_thermal_module_exit(void) { - platform_driver_unregister(&mid_thermal_driver); + platform_driver_unregister(&mid_thermal_driver); } module_init(mid_thermal_module_init); -- cgit v1.2.3 From 112a6ee053f9e9f014ab64f2549d3a25551aa349 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Mon, 4 Apr 2011 10:06:24 -0700 Subject: thinkpad_acpi: Correct !CONFIG_THINKPAD_ACPI_VIDEO warning Move TPACPI_HANDLE declaration into #ifdef block and neaten it a bit. Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/thinkpad_acpi.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index 562fcf0dd2b..7693e89459f 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -535,15 +535,6 @@ TPACPI_HANDLE(hkey, ec, "\\_SB.HKEY", /* 600e/x, 770e, 770x */ "HKEY", /* all others */ ); /* 570 */ -TPACPI_HANDLE(vid, root, "\\_SB.PCI.AGP.VGA", /* 570 */ - "\\_SB.PCI0.AGP0.VID0", /* 600e/x, 770x */ - "\\_SB.PCI0.VID0", /* 770e */ - "\\_SB.PCI0.VID", /* A21e, G4x, R50e, X30, X40 */ - "\\_SB.PCI0.AGP.VGA", /* X100e and a few others */ - "\\_SB.PCI0.AGP.VID", /* all others */ - ); /* R30, R31 */ - - /************************************************************************* * ACPI helpers */ @@ -4444,6 +4435,15 @@ static int video_orig_autosw; static int video_autosw_get(void); static int video_autosw_set(int enable); +TPACPI_HANDLE(vid, root, + "\\_SB.PCI.AGP.VGA", /* 570 */ + "\\_SB.PCI0.AGP0.VID0", /* 600e/x, 770x */ + "\\_SB.PCI0.VID0", /* 770e */ + "\\_SB.PCI0.VID", /* A21e, G4x, R50e, X30, X40 */ + "\\_SB.PCI0.AGP.VGA", /* X100e and a few others */ + "\\_SB.PCI0.AGP.VID", /* all others */ + ); /* R30, R31 */ + TPACPI_HANDLE(vid2, root, "\\_SB.PCI0.AGPB.VID"); /* G41 */ static int __init video_init(struct ibm_init_struct *iibm) -- cgit v1.2.3 From 0978e012cfbaca8bd312933e98cdea2d11778e11 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Mon, 4 Apr 2011 10:06:25 -0700 Subject: thinkpad_acpi: Convert printks to pr_ Add pr_fmt. Removed local TPACPI_ #defines, convert to pr_. Neaten dbg_ macros. Added a few missing newlines to logging messages. Added static inline str_supported for !CONFIG_THINKPAD_ACPI_DEBUG vdbg_printk defect reported by Sedat Dilek . Signed-off-by: Joe Perches Signed-off-by: Matthew Garrett --- drivers/platform/x86/thinkpad_acpi.c | 472 ++++++++++++++--------------------- 1 file changed, 188 insertions(+), 284 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index 7693e89459f..77f6e707a2a 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -21,6 +21,8 @@ * 02110-1301, USA. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #define TPACPI_VERSION "0.24" #define TPACPI_SYSFS_VERSION 0x020700 @@ -224,17 +226,6 @@ enum tpacpi_hkey_event_t { #define TPACPI_MAX_ACPI_ARGS 3 -/* printk headers */ -#define TPACPI_LOG TPACPI_FILE ": " -#define TPACPI_EMERG KERN_EMERG TPACPI_LOG -#define TPACPI_ALERT KERN_ALERT TPACPI_LOG -#define TPACPI_CRIT KERN_CRIT TPACPI_LOG -#define TPACPI_ERR KERN_ERR TPACPI_LOG -#define TPACPI_WARN KERN_WARNING TPACPI_LOG -#define TPACPI_NOTICE KERN_NOTICE TPACPI_LOG -#define TPACPI_INFO KERN_INFO TPACPI_LOG -#define TPACPI_DEBUG KERN_DEBUG TPACPI_LOG - /* Debugging printk groups */ #define TPACPI_DBG_ALL 0xffff #define TPACPI_DBG_DISCLOSETASK 0x8000 @@ -389,34 +380,36 @@ static int tpacpi_uwb_emulstate; * Debugging helpers */ -#define dbg_printk(a_dbg_level, format, arg...) \ - do { if (dbg_level & (a_dbg_level)) \ - printk(TPACPI_DEBUG "%s: " format, __func__ , ## arg); \ - } while (0) +#define dbg_printk(a_dbg_level, format, arg...) \ +do { \ + if (dbg_level & (a_dbg_level)) \ + printk(KERN_DEBUG pr_fmt("%s: " format), \ + __func__, ##arg); \ +} while (0) #ifdef CONFIG_THINKPAD_ACPI_DEBUG #define vdbg_printk dbg_printk static const char *str_supported(int is_supported); #else -#define vdbg_printk(a_dbg_level, format, arg...) \ - do { } while (0) +static inline const char *str_supported(int is_supported) { return ""; } +#define vdbg_printk(a_dbg_level, format, arg...) \ + no_printk(format, ##arg) #endif static void tpacpi_log_usertask(const char * const what) { - printk(TPACPI_DEBUG "%s: access by process with PID %d\n", - what, task_tgid_vnr(current)); + printk(KERN_DEBUG pr_fmt("%s: access by process with PID %d\n"), + what, task_tgid_vnr(current)); } -#define tpacpi_disclose_usertask(what, format, arg...) \ - do { \ - if (unlikely( \ - (dbg_level & TPACPI_DBG_DISCLOSETASK) && \ - (tpacpi_lifecycle == TPACPI_LIFE_RUNNING))) { \ - printk(TPACPI_DEBUG "%s: PID %d: " format, \ - what, task_tgid_vnr(current), ## arg); \ - } \ - } while (0) +#define tpacpi_disclose_usertask(what, format, arg...) \ +do { \ + if (unlikely((dbg_level & TPACPI_DBG_DISCLOSETASK) && \ + (tpacpi_lifecycle == TPACPI_LIFE_RUNNING))) { \ + printk(KERN_DEBUG pr_fmt("%s: PID %d: " format), \ + what, task_tgid_vnr(current), ## arg); \ + } \ +} while (0) /* * Quirk handling helpers @@ -554,7 +547,7 @@ static int acpi_evalf(acpi_handle handle, int quiet; if (!*fmt) { - printk(TPACPI_ERR "acpi_evalf() called with empty format\n"); + pr_err("acpi_evalf() called with empty format\n"); return 0; } @@ -579,7 +572,7 @@ static int acpi_evalf(acpi_handle handle, break; /* add more types as needed */ default: - printk(TPACPI_ERR "acpi_evalf() called " + pr_err("acpi_evalf() called " "with invalid format character '%c'\n", c); va_end(ap); return 0; @@ -608,13 +601,13 @@ static int acpi_evalf(acpi_handle handle, break; /* add more types as needed */ default: - printk(TPACPI_ERR "acpi_evalf() called " + pr_err("acpi_evalf() called " "with invalid format character '%c'\n", res_type); return 0; } if (!success && !quiet) - printk(TPACPI_ERR "acpi_evalf(%s, %s, ...) failed: %s\n", + pr_err("acpi_evalf(%s, %s, ...) failed: %s\n", method, fmt0, acpi_format_exception(status)); return success; @@ -758,8 +751,7 @@ static int __init setup_acpi_notify(struct ibm_struct *ibm) rc = acpi_bus_get_device(*ibm->acpi->handle, &ibm->acpi->device); if (rc < 0) { - printk(TPACPI_ERR "acpi_bus_get_device(%s) failed: %d\n", - ibm->name, rc); + pr_err("acpi_bus_get_device(%s) failed: %d\n", ibm->name, rc); return -ENODEV; } @@ -772,12 +764,10 @@ static int __init setup_acpi_notify(struct ibm_struct *ibm) ibm->acpi->type, dispatch_acpi_notify, ibm); if (ACPI_FAILURE(status)) { if (status == AE_ALREADY_EXISTS) { - printk(TPACPI_NOTICE - "another device driver is already " - "handling %s events\n", ibm->name); + pr_notice("another device driver is already " + "handling %s events\n", ibm->name); } else { - printk(TPACPI_ERR - "acpi_install_notify_handler(%s) failed: %s\n", + pr_err("acpi_install_notify_handler(%s) failed: %s\n", ibm->name, acpi_format_exception(status)); } return -ENODEV; @@ -802,8 +792,7 @@ static int __init register_tpacpi_subdriver(struct ibm_struct *ibm) ibm->acpi->driver = kzalloc(sizeof(struct acpi_driver), GFP_KERNEL); if (!ibm->acpi->driver) { - printk(TPACPI_ERR - "failed to allocate memory for ibm->acpi->driver\n"); + pr_err("failed to allocate memory for ibm->acpi->driver\n"); return -ENOMEM; } @@ -814,7 +803,7 @@ static int __init register_tpacpi_subdriver(struct ibm_struct *ibm) rc = acpi_bus_register_driver(ibm->acpi->driver); if (rc < 0) { - printk(TPACPI_ERR "acpi_bus_register_driver(%s) failed: %d\n", + pr_err("acpi_bus_register_driver(%s) failed: %d\n", ibm->name, rc); kfree(ibm->acpi->driver); ibm->acpi->driver = NULL; @@ -1072,15 +1061,14 @@ static int parse_strtoul(const char *buf, static void tpacpi_disable_brightness_delay(void) { if (acpi_evalf(hkey_handle, NULL, "PWMS", "qvd", 0)) - printk(TPACPI_NOTICE - "ACPI backlight control delay disabled\n"); + pr_notice("ACPI backlight control delay disabled\n"); } static void printk_deprecated_attribute(const char * const what, const char * const details) { tpacpi_log_usertask("deprecated sysfs attribute"); - printk(TPACPI_WARN "WARNING: sysfs attribute %s is deprecated and " + pr_warn("WARNING: sysfs attribute %s is deprecated and " "will be removed. %s\n", what, details); } @@ -1255,8 +1243,7 @@ static int __init tpacpi_new_rfkill(const enum tpacpi_rfk_id id, &tpacpi_rfk_rfkill_ops, atp_rfk); if (!atp_rfk || !atp_rfk->rfkill) { - printk(TPACPI_ERR - "failed to allocate memory for rfkill class\n"); + pr_err("failed to allocate memory for rfkill class\n"); kfree(atp_rfk); return -ENOMEM; } @@ -1266,9 +1253,8 @@ static int __init tpacpi_new_rfkill(const enum tpacpi_rfk_id id, sw_status = (tp_rfkops->get_status)(); if (sw_status < 0) { - printk(TPACPI_ERR - "failed to read initial state for %s, error %d\n", - name, sw_status); + pr_err("failed to read initial state for %s, error %d\n", + name, sw_status); } else { sw_state = (sw_status == TPACPI_RFK_RADIO_OFF); if (set_default) { @@ -1282,9 +1268,7 @@ static int __init tpacpi_new_rfkill(const enum tpacpi_rfk_id id, res = rfkill_register(atp_rfk->rfkill); if (res < 0) { - printk(TPACPI_ERR - "failed to register %s rfkill switch: %d\n", - name, res); + pr_err("failed to register %s rfkill switch: %d\n", name, res); rfkill_destroy(atp_rfk->rfkill); kfree(atp_rfk); return res; @@ -1292,7 +1276,7 @@ static int __init tpacpi_new_rfkill(const enum tpacpi_rfk_id id, tpacpi_rfkill_switches[id] = atp_rfk; - printk(TPACPI_INFO "rfkill switch %s: radio is %sblocked\n", + pr_info("rfkill switch %s: radio is %sblocked\n", name, (sw_state || hw_state) ? "" : "un"); return 0; } @@ -1816,10 +1800,8 @@ static void __init tpacpi_check_outdated_fw(void) * broken, or really stable to begin with, so it is * best if the user upgrades the firmware anyway. */ - printk(TPACPI_WARN - "WARNING: Outdated ThinkPad BIOS/EC firmware\n"); - printk(TPACPI_WARN - "WARNING: This firmware may be missing critical bug " + pr_warn("WARNING: Outdated ThinkPad BIOS/EC firmware\n"); + pr_warn("WARNING: This firmware may be missing critical bug " "fixes and/or important features\n"); } } @@ -2108,9 +2090,7 @@ void static hotkey_mask_warn_incomplete_mask(void) (hotkey_all_mask | TPACPI_HKEY_NVRAM_KNOWN_MASK); if (wantedmask) - printk(TPACPI_NOTICE - "required events 0x%08x not enabled!\n", - wantedmask); + pr_notice("required events 0x%08x not enabled!\n", wantedmask); } /* @@ -2148,10 +2128,9 @@ static int hotkey_mask_set(u32 mask) * a given event. */ if (!hotkey_mask_get() && !rc && (fwmask & ~hotkey_acpi_mask)) { - printk(TPACPI_NOTICE - "asked for hotkey mask 0x%08x, but " - "firmware forced it to 0x%08x\n", - fwmask, hotkey_acpi_mask); + pr_notice("asked for hotkey mask 0x%08x, but " + "firmware forced it to 0x%08x\n", + fwmask, hotkey_acpi_mask); } if (tpacpi_lifecycle != TPACPI_LIFE_EXITING) @@ -2175,13 +2154,11 @@ static int hotkey_user_mask_set(const u32 mask) (mask == 0xffff || mask == 0xffffff || mask == 0xffffffff)) { tp_warned.hotkey_mask_ff = 1; - printk(TPACPI_NOTICE - "setting the hotkey mask to 0x%08x is likely " - "not the best way to go about it\n", mask); - printk(TPACPI_NOTICE - "please consider using the driver defaults, " - "and refer to up-to-date thinkpad-acpi " - "documentation\n"); + pr_notice("setting the hotkey mask to 0x%08x is likely " + "not the best way to go about it\n", mask); + pr_notice("please consider using the driver defaults, " + "and refer to up-to-date thinkpad-acpi " + "documentation\n"); } /* Try to enable what the user asked for, plus whatever we need. @@ -2565,8 +2542,7 @@ static void hotkey_poll_setup(const bool may_warn) NULL, TPACPI_NVRAM_KTHREAD_NAME); if (IS_ERR(tpacpi_hotkey_task)) { tpacpi_hotkey_task = NULL; - printk(TPACPI_ERR - "could not create kernel thread " + pr_err("could not create kernel thread " "for hotkey polling\n"); } } @@ -2574,11 +2550,10 @@ static void hotkey_poll_setup(const bool may_warn) hotkey_poll_stop_sync(); if (may_warn && (poll_driver_mask || poll_user_mask) && hotkey_poll_freq == 0) { - printk(TPACPI_NOTICE - "hot keys 0x%08x and/or events 0x%08x " - "require polling, which is currently " - "disabled\n", - poll_user_mask, poll_driver_mask); + pr_notice("hot keys 0x%08x and/or events 0x%08x " + "require polling, which is currently " + "disabled\n", + poll_user_mask, poll_driver_mask); } } } @@ -2802,13 +2777,13 @@ static ssize_t hotkey_source_mask_store(struct device *dev, mutex_unlock(&hotkey_mutex); if (rc < 0) - printk(TPACPI_ERR "hotkey_source_mask: failed to update the" - "firmware event mask!\n"); + pr_err("hotkey_source_mask: " + "failed to update the firmware event mask!\n"); if (r_ev) - printk(TPACPI_NOTICE "hotkey_source_mask: " - "some important events were disabled: " - "0x%04x\n", r_ev); + pr_notice("hotkey_source_mask: " + "some important events were disabled: 0x%04x\n", + r_ev); tpacpi_disclose_usertask("hotkey_source_mask", "set to 0x%08lx\n", t); @@ -3039,8 +3014,7 @@ static void hotkey_exit(void) if (((tp_features.hotkey_mask && hotkey_mask_set(hotkey_orig_mask)) | hotkey_status_set(false)) != 0) - printk(TPACPI_ERR - "failed to restore hot key mask " + pr_err("failed to restore hot key mask " "to BIOS defaults\n"); } @@ -3279,10 +3253,9 @@ static int __init hotkey_init(struct ibm_init_struct *iibm) for HKEY interface version 0x100 */ if (acpi_evalf(hkey_handle, &hkeyv, "MHKV", "qd")) { if ((hkeyv >> 8) != 1) { - printk(TPACPI_ERR "unknown version of the " - "HKEY interface: 0x%x\n", hkeyv); - printk(TPACPI_ERR "please report this to %s\n", - TPACPI_MAIL); + pr_err("unknown version of the HKEY interface: 0x%x\n", + hkeyv); + pr_err("please report this to %s\n", TPACPI_MAIL); } else { /* * MHKV 0x100 in A31, R40, R40e, @@ -3295,8 +3268,7 @@ static int __init hotkey_init(struct ibm_init_struct *iibm) /* Paranoia check AND init hotkey_all_mask */ if (!acpi_evalf(hkey_handle, &hotkey_all_mask, "MHKA", "qd")) { - printk(TPACPI_ERR - "missing MHKA handler, " + pr_err("missing MHKA handler, " "please report this to %s\n", TPACPI_MAIL); /* Fallback: pre-init for FN+F3,F4,F12 */ @@ -3334,16 +3306,14 @@ static int __init hotkey_init(struct ibm_init_struct *iibm) if (dbg_wlswemul) { tp_features.hotkey_wlsw = 1; radiosw_state = !!tpacpi_wlsw_emulstate; - printk(TPACPI_INFO - "radio switch emulation enabled\n"); + pr_info("radio switch emulation enabled\n"); } else #endif /* Not all thinkpads have a hardware radio switch */ if (acpi_evalf(hkey_handle, &status, "WLSW", "qd")) { tp_features.hotkey_wlsw = 1; radiosw_state = !!status; - printk(TPACPI_INFO - "radio switch found; radios are %s\n", + pr_info("radio switch found; radios are %s\n", enabled(status, 0)); } if (tp_features.hotkey_wlsw) @@ -3354,8 +3324,7 @@ static int __init hotkey_init(struct ibm_init_struct *iibm) if (!res && acpi_evalf(hkey_handle, &status, "MHKG", "qd")) { tp_features.hotkey_tablet = 1; tabletsw_state = !!(status & TP_HOTKEY_TABLET_MASK); - printk(TPACPI_INFO - "possible tablet mode switch found; " + pr_info("possible tablet mode switch found; " "ThinkPad in %s mode\n", (tabletsw_state) ? "tablet" : "laptop"); res = add_to_attr_set(hotkey_dev_attributes, @@ -3373,8 +3342,7 @@ static int __init hotkey_init(struct ibm_init_struct *iibm) hotkey_keycode_map = kmalloc(TPACPI_HOTKEY_MAP_SIZE, GFP_KERNEL); if (!hotkey_keycode_map) { - printk(TPACPI_ERR - "failed to allocate memory for key map\n"); + pr_err("failed to allocate memory for key map\n"); res = -ENOMEM; goto err_exit; } @@ -3417,13 +3385,11 @@ static int __init hotkey_init(struct ibm_init_struct *iibm) * userspace. tpacpi_detect_brightness_capabilities() must have * been called before this point */ if (tp_features.bright_acpimode && acpi_video_backlight_support()) { - printk(TPACPI_INFO - "This ThinkPad has standard ACPI backlight " - "brightness control, supported by the ACPI " - "video driver\n"); - printk(TPACPI_NOTICE - "Disabling thinkpad-acpi brightness events " - "by default...\n"); + pr_info("This ThinkPad has standard ACPI backlight " + "brightness control, supported by the ACPI " + "video driver\n"); + pr_notice("Disabling thinkpad-acpi brightness events " + "by default...\n"); /* Disable brightness up/down on Lenovo thinkpads when * ACPI is handling them, otherwise it is plain impossible @@ -3530,8 +3496,7 @@ static bool hotkey_notify_wakeup(const u32 hkey, case TP_HKEY_EV_WKUP_S3_BATLOW: /* Battery on critical low level/S3 */ case TP_HKEY_EV_WKUP_S4_BATLOW: /* Battery on critical low level/S4 */ - printk(TPACPI_ALERT - "EMERGENCY WAKEUP: battery almost empty\n"); + pr_alert("EMERGENCY WAKEUP: battery almost empty\n"); /* how to auto-heal: */ /* 2313: woke up from S3, go to S4/S5 */ /* 2413: woke up from S4, go to S5 */ @@ -3542,9 +3507,7 @@ static bool hotkey_notify_wakeup(const u32 hkey, } if (hotkey_wakeup_reason != TP_ACPI_WAKEUP_NONE) { - printk(TPACPI_INFO - "woke up due to a hot-unplug " - "request...\n"); + pr_info("woke up due to a hot-unplug request...\n"); hotkey_wakeup_reason_notify_change(); } return true; @@ -3596,37 +3559,31 @@ static bool hotkey_notify_thermal(const u32 hkey, switch (hkey) { case TP_HKEY_EV_THM_TABLE_CHANGED: - printk(TPACPI_INFO - "EC reports that Thermal Table has changed\n"); + pr_info("EC reports that Thermal Table has changed\n"); /* recommended action: do nothing, we don't have * Lenovo ATM information */ return true; case TP_HKEY_EV_ALARM_BAT_HOT: - printk(TPACPI_CRIT - "THERMAL ALARM: battery is too hot!\n"); + pr_crit("THERMAL ALARM: battery is too hot!\n"); /* recommended action: warn user through gui */ break; case TP_HKEY_EV_ALARM_BAT_XHOT: - printk(TPACPI_ALERT - "THERMAL EMERGENCY: battery is extremely hot!\n"); + pr_alert("THERMAL EMERGENCY: battery is extremely hot!\n"); /* recommended action: immediate sleep/hibernate */ break; case TP_HKEY_EV_ALARM_SENSOR_HOT: - printk(TPACPI_CRIT - "THERMAL ALARM: " + pr_crit("THERMAL ALARM: " "a sensor reports something is too hot!\n"); /* recommended action: warn user through gui, that */ /* some internal component is too hot */ break; case TP_HKEY_EV_ALARM_SENSOR_XHOT: - printk(TPACPI_ALERT - "THERMAL EMERGENCY: " - "a sensor reports something is extremely hot!\n"); + pr_alert("THERMAL EMERGENCY: " + "a sensor reports something is extremely hot!\n"); /* recommended action: immediate sleep/hibernate */ break; default: - printk(TPACPI_ALERT - "THERMAL ALERT: unknown thermal alarm received\n"); + pr_alert("THERMAL ALERT: unknown thermal alarm received\n"); known = false; } @@ -3643,8 +3600,7 @@ static void hotkey_notify(struct ibm_struct *ibm, u32 event) bool known_ev; if (event != 0x80) { - printk(TPACPI_ERR - "unknown HKEY notification event %d\n", event); + pr_err("unknown HKEY notification event %d\n", event); /* forward it to userspace, maybe it knows how to handle it */ acpi_bus_generate_netlink_event( ibm->acpi->device->pnp.device_class, @@ -3655,7 +3611,7 @@ static void hotkey_notify(struct ibm_struct *ibm, u32 event) while (1) { if (!acpi_evalf(hkey_handle, &hkey, "MHKP", "d")) { - printk(TPACPI_ERR "failed to retrieve HKEY event\n"); + pr_err("failed to retrieve HKEY event\n"); return; } @@ -3683,8 +3639,7 @@ static void hotkey_notify(struct ibm_struct *ibm, u32 event) switch (hkey) { case TP_HKEY_EV_BAYEJ_ACK: hotkey_autosleep_ack = 1; - printk(TPACPI_INFO - "bay ejected\n"); + pr_info("bay ejected\n"); hotkey_wakeup_hotunplug_complete_notify_change(); known_ev = true; break; @@ -3700,8 +3655,7 @@ static void hotkey_notify(struct ibm_struct *ibm, u32 event) /* 0x4000-0x4FFF: dock-related wakeups */ if (hkey == TP_HKEY_EV_UNDOCK_ACK) { hotkey_autosleep_ack = 1; - printk(TPACPI_INFO - "undocked\n"); + pr_info("undocked\n"); hotkey_wakeup_hotunplug_complete_notify_change(); known_ev = true; } else { @@ -3732,11 +3686,9 @@ static void hotkey_notify(struct ibm_struct *ibm, u32 event) known_ev = false; } if (!known_ev) { - printk(TPACPI_NOTICE - "unhandled HKEY event 0x%04x\n", hkey); - printk(TPACPI_NOTICE - "please report the conditions when this " - "event happened to %s\n", TPACPI_MAIL); + pr_notice("unhandled HKEY event 0x%04x\n", hkey); + pr_notice("please report the conditions when this " + "event happened to %s\n", TPACPI_MAIL); } /* Legacy events */ @@ -3769,8 +3721,7 @@ static void hotkey_resume(void) if (hotkey_status_set(true) < 0 || hotkey_mask_set(hotkey_acpi_mask) < 0) - printk(TPACPI_ERR - "error while attempting to reset the event " + pr_err("error while attempting to reset the event " "firmware interface\n"); tpacpi_send_radiosw_update(); @@ -3815,14 +3766,12 @@ static void hotkey_enabledisable_warn(bool enable) { tpacpi_log_usertask("procfs hotkey enable/disable"); if (!WARN((tpacpi_lifecycle == TPACPI_LIFE_RUNNING || !enable), - TPACPI_WARN - "hotkey enable/disable functionality has been " - "removed from the driver. Hotkeys are always " - "enabled\n")) - printk(TPACPI_ERR - "Please remove the hotkey=enable module " - "parameter, it is deprecated. Hotkeys are always " - "enabled\n"); + pr_fmt("hotkey enable/disable functionality has been " + "removed from the driver. " + "Hotkeys are always enabled.\n"))) + pr_err("Please remove the hotkey=enable module " + "parameter, it is deprecated. " + "Hotkeys are always enabled.\n"); } static int hotkey_write(char *buf) @@ -4002,8 +3951,7 @@ static void bluetooth_shutdown(void) /* Order firmware to save current state to NVRAM */ if (!acpi_evalf(NULL, NULL, "\\BLTH", "vd", TP_ACPI_BLTH_SAVE_STATE)) - printk(TPACPI_NOTICE - "failed to save bluetooth state to NVRAM\n"); + pr_notice("failed to save bluetooth state to NVRAM\n"); else vdbg_printk(TPACPI_DBG_RFKILL, "bluestooth state saved to NVRAM\n"); @@ -4042,8 +3990,7 @@ static int __init bluetooth_init(struct ibm_init_struct *iibm) #ifdef CONFIG_THINKPAD_ACPI_DEBUGFACILITIES if (dbg_bluetoothemul) { tp_features.bluetooth = 1; - printk(TPACPI_INFO - "bluetooth switch emulation enabled\n"); + pr_info("bluetooth switch emulation enabled\n"); } else #endif if (tp_features.bluetooth && @@ -4194,8 +4141,7 @@ static void wan_shutdown(void) /* Order firmware to save current state to NVRAM */ if (!acpi_evalf(NULL, NULL, "\\WGSV", "vd", TP_ACPI_WGSV_SAVE_STATE)) - printk(TPACPI_NOTICE - "failed to save WWAN state to NVRAM\n"); + pr_notice("failed to save WWAN state to NVRAM\n"); else vdbg_printk(TPACPI_DBG_RFKILL, "WWAN state saved to NVRAM\n"); @@ -4232,8 +4178,7 @@ static int __init wan_init(struct ibm_init_struct *iibm) #ifdef CONFIG_THINKPAD_ACPI_DEBUGFACILITIES if (dbg_wwanemul) { tp_features.wan = 1; - printk(TPACPI_INFO - "wwan switch emulation enabled\n"); + pr_info("wwan switch emulation enabled\n"); } else #endif if (tp_features.wan && @@ -4373,8 +4318,7 @@ static int __init uwb_init(struct ibm_init_struct *iibm) #ifdef CONFIG_THINKPAD_ACPI_DEBUGFACILITIES if (dbg_uwbemul) { tp_features.uwb = 1; - printk(TPACPI_INFO - "uwb switch emulation enabled\n"); + pr_info("uwb switch emulation enabled\n"); } else #endif if (tp_features.uwb && @@ -4487,7 +4431,7 @@ static void video_exit(void) dbg_printk(TPACPI_DBG_EXIT, "restoring original video autoswitch mode\n"); if (video_autosw_set(video_orig_autosw)) - printk(TPACPI_ERR "error while trying to restore original " + pr_err("error while trying to restore original " "video autoswitch mode\n"); } @@ -4560,8 +4504,7 @@ static int video_outputsw_set(int status) res = acpi_evalf(vid_handle, NULL, "ASWT", "vdd", status * 0x100, 0); if (!autosw && video_autosw_set(autosw)) { - printk(TPACPI_ERR - "video auto-switch left enabled due to error\n"); + pr_err("video auto-switch left enabled due to error\n"); return -EIO; } break; @@ -4630,8 +4573,7 @@ static int video_outputsw_cycle(void) return -ENOSYS; } if (!autosw && video_autosw_set(autosw)) { - printk(TPACPI_ERR - "video auto-switch left enabled due to error\n"); + pr_err("video auto-switch left enabled due to error\n"); return -EIO; } @@ -5348,7 +5290,7 @@ static int __init led_init(struct ibm_init_struct *iibm) tpacpi_leds = kzalloc(sizeof(*tpacpi_leds) * TPACPI_LED_NUMLEDS, GFP_KERNEL); if (!tpacpi_leds) { - printk(TPACPI_ERR "Out of memory for LED data\n"); + pr_err("Out of memory for LED data\n"); return -ENOMEM; } @@ -5367,9 +5309,8 @@ static int __init led_init(struct ibm_init_struct *iibm) } #ifdef CONFIG_THINKPAD_ACPI_UNSAFE_LEDS - printk(TPACPI_NOTICE - "warning: userspace override of important " - "firmware LEDs is enabled\n"); + pr_notice("warning: userspace override of important " + "firmware LEDs is enabled\n"); #endif return 0; } @@ -5639,17 +5580,16 @@ static void thermal_dump_all_sensors(void) if (n <= 0) return; - printk(TPACPI_NOTICE - "temperatures (Celsius):"); + pr_notice("temperatures (Celsius):"); for (i = 0; i < n; i++) { if (t.temp[i] != TPACPI_THERMAL_SENSOR_NA) - printk(KERN_CONT " %d", (int)(t.temp[i] / 1000)); + pr_cont(" %d", (int)(t.temp[i] / 1000)); else - printk(KERN_CONT " N/A"); + pr_cont(" N/A"); } - printk(KERN_CONT "\n"); + pr_cont("\n"); } /* sysfs temp##_input -------------------------------------------------- */ @@ -5769,14 +5709,12 @@ static int __init thermal_init(struct ibm_init_struct *iibm) if (ta1 == 0) { /* This is sheer paranoia, but we handle it anyway */ if (acpi_tmp7) { - printk(TPACPI_ERR - "ThinkPad ACPI EC access misbehaving, " + pr_err("ThinkPad ACPI EC access misbehaving, " "falling back to ACPI TMPx access " "mode\n"); thermal_read_mode = TPACPI_THERMAL_ACPI_TMP07; } else { - printk(TPACPI_ERR - "ThinkPad ACPI EC access misbehaving, " + pr_err("ThinkPad ACPI EC access misbehaving, " "disabling thermal sensors access\n"); thermal_read_mode = TPACPI_THERMAL_NONE; } @@ -6129,8 +6067,8 @@ static int __init tpacpi_query_bcl_levels(acpi_handle handle) if (ACPI_SUCCESS(acpi_evaluate_object(handle, "_BCL", NULL, &buffer))) { obj = (union acpi_object *)buffer.pointer; if (!obj || (obj->type != ACPI_TYPE_PACKAGE)) { - printk(TPACPI_ERR "Unknown _BCL data, " - "please report this to %s\n", TPACPI_MAIL); + pr_err("Unknown _BCL data, please report this to %s\n", + TPACPI_MAIL); rc = 0; } else { rc = obj->package.count; @@ -6214,18 +6152,15 @@ static void __init tpacpi_detect_brightness_capabilities(void) switch (b) { case 16: bright_maxlvl = 15; - printk(TPACPI_INFO - "detected a 16-level brightness capable ThinkPad\n"); + pr_info("detected a 16-level brightness capable ThinkPad\n"); break; case 8: case 0: bright_maxlvl = 7; - printk(TPACPI_INFO - "detected a 8-level brightness capable ThinkPad\n"); + pr_info("detected a 8-level brightness capable ThinkPad\n"); break; default: - printk(TPACPI_ERR - "Unsupported brightness interface, " + pr_err("Unsupported brightness interface, " "please contact %s\n", TPACPI_MAIL); tp_features.bright_unkfw = 1; bright_maxlvl = b - 1; @@ -6260,22 +6195,19 @@ static int __init brightness_init(struct ibm_init_struct *iibm) if (acpi_video_backlight_support()) { if (brightness_enable > 1) { - printk(TPACPI_INFO - "Standard ACPI backlight interface " - "available, not loading native one.\n"); + pr_info("Standard ACPI backlight interface " + "available, not loading native one\n"); return 1; } else if (brightness_enable == 1) { - printk(TPACPI_WARN - "Cannot enable backlight brightness support, " + pr_warn("Cannot enable backlight brightness support, " "ACPI is already handling it. Refer to the " - "acpi_backlight kernel parameter\n"); + "acpi_backlight kernel parameter.\n"); return 1; } } else if (tp_features.bright_acpimode && brightness_enable > 1) { - printk(TPACPI_NOTICE - "Standard ACPI backlight interface not " - "available, thinkpad_acpi native " - "brightness control enabled\n"); + pr_notice("Standard ACPI backlight interface not " + "available, thinkpad_acpi native " + "brightness control enabled\n"); } /* @@ -6319,19 +6251,17 @@ static int __init brightness_init(struct ibm_init_struct *iibm) if (IS_ERR(ibm_backlight_device)) { int rc = PTR_ERR(ibm_backlight_device); ibm_backlight_device = NULL; - printk(TPACPI_ERR "Could not register backlight device\n"); + pr_err("Could not register backlight device\n"); return rc; } vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_BRGHT, "brightness is supported\n"); if (quirks & TPACPI_BRGHT_Q_ASK) { - printk(TPACPI_NOTICE - "brightness: will use unverified default: " - "brightness_mode=%d\n", brightness_mode); - printk(TPACPI_NOTICE - "brightness: please report to %s whether it works well " - "or not on your ThinkPad\n", TPACPI_MAIL); + pr_notice("brightness: will use unverified default: " + "brightness_mode=%d\n", brightness_mode); + pr_notice("brightness: please report to %s whether it works well " + "or not on your ThinkPad\n", TPACPI_MAIL); } /* Added by mistake in early 2007. Probably useless, but it could @@ -6804,8 +6734,7 @@ static int __init volume_create_alsa_mixer(void) rc = snd_card_create(alsa_index, alsa_id, THIS_MODULE, sizeof(struct tpacpi_alsa_data), &card); if (rc < 0 || !card) { - printk(TPACPI_ERR - "Failed to create ALSA card structures: %d\n", rc); + pr_err("Failed to create ALSA card structures: %d\n", rc); return 1; } @@ -6839,9 +6768,8 @@ static int __init volume_create_alsa_mixer(void) ctl_vol = snd_ctl_new1(&volume_alsa_control_vol, NULL); rc = snd_ctl_add(card, ctl_vol); if (rc < 0) { - printk(TPACPI_ERR - "Failed to create ALSA volume control: %d\n", - rc); + pr_err("Failed to create ALSA volume control: %d\n", + rc); goto err_exit; } data->ctl_vol_id = &ctl_vol->id; @@ -6850,8 +6778,7 @@ static int __init volume_create_alsa_mixer(void) ctl_mute = snd_ctl_new1(&volume_alsa_control_mute, NULL); rc = snd_ctl_add(card, ctl_mute); if (rc < 0) { - printk(TPACPI_ERR "Failed to create ALSA mute control: %d\n", - rc); + pr_err("Failed to create ALSA mute control: %d\n", rc); goto err_exit; } data->ctl_mute_id = &ctl_mute->id; @@ -6859,7 +6786,7 @@ static int __init volume_create_alsa_mixer(void) snd_card_set_dev(card, &tpacpi_pdev->dev); rc = snd_card_register(card); if (rc < 0) { - printk(TPACPI_ERR "Failed to register ALSA card: %d\n", rc); + pr_err("Failed to register ALSA card: %d\n", rc); goto err_exit; } @@ -6915,9 +6842,8 @@ static int __init volume_init(struct ibm_init_struct *iibm) return -EINVAL; if (volume_mode == TPACPI_VOL_MODE_UCMS_STEP) { - printk(TPACPI_ERR - "UCMS step volume mode not implemented, " - "please contact %s\n", TPACPI_MAIL); + pr_err("UCMS step volume mode not implemented, " + "please contact %s\n", TPACPI_MAIL); return 1; } @@ -6981,13 +6907,11 @@ static int __init volume_init(struct ibm_init_struct *iibm) rc = volume_create_alsa_mixer(); if (rc) { - printk(TPACPI_ERR - "Could not create the ALSA mixer interface\n"); + pr_err("Could not create the ALSA mixer interface\n"); return rc; } - printk(TPACPI_INFO - "Console audio control enabled, mode: %s\n", + pr_info("Console audio control enabled, mode: %s\n", (volume_control_allowed) ? "override (read/write)" : "monitor (read only)"); @@ -7049,12 +6973,10 @@ static int volume_write(char *buf) if (!volume_control_allowed && tpacpi_lifecycle != TPACPI_LIFE_INIT) { if (unlikely(!tp_warned.volume_ctrl_forbidden)) { tp_warned.volume_ctrl_forbidden = 1; - printk(TPACPI_NOTICE - "Console audio control in monitor mode, " - "changes are not allowed.\n"); - printk(TPACPI_NOTICE - "Use the volume_control=1 module parameter " - "to enable volume control\n"); + pr_notice("Console audio control in monitor mode, " + "changes are not allowed\n"); + pr_notice("Use the volume_control=1 module parameter " + "to enable volume control\n"); } return -EPERM; } @@ -7129,8 +7051,7 @@ static void inline volume_alsa_notify_change(void) static int __init volume_init(struct ibm_init_struct *iibm) { - printk(TPACPI_INFO - "volume: disabled as there is no ALSA support in this kernel\n"); + pr_info("volume: disabled as there is no ALSA support in this kernel\n"); return 1; } @@ -7337,9 +7258,8 @@ TPACPI_HANDLE(sfan, ec, "SFAN", /* 570 */ static void fan_quirk1_setup(void) { if (fan_control_initial_status == 0x07) { - printk(TPACPI_NOTICE - "fan_init: initial fan status is unknown, " - "assuming it is in auto mode\n"); + pr_notice("fan_init: initial fan status is unknown, " + "assuming it is in auto mode\n"); tp_features.fan_ctrl_status_undef = 1; } } @@ -7726,8 +7646,7 @@ static void fan_watchdog_reset(void) if (!queue_delayed_work(tpacpi_wq, &fan_watchdog_task, msecs_to_jiffies(fan_watchdog_maxinterval * 1000))) { - printk(TPACPI_ERR - "failed to queue the fan watchdog, " + pr_err("failed to queue the fan watchdog, " "watchdog will not trigger\n"); } } else @@ -7741,11 +7660,11 @@ static void fan_watchdog_fire(struct work_struct *ignored) if (tpacpi_lifecycle != TPACPI_LIFE_RUNNING) return; - printk(TPACPI_NOTICE "fan watchdog: enabling fan\n"); + pr_notice("fan watchdog: enabling fan\n"); rc = fan_set_enable(); if (rc < 0) { - printk(TPACPI_ERR "fan watchdog: error %d while enabling fan, " - "will try again later...\n", -rc); + pr_err("fan watchdog: error %d while enabling fan, " + "will try again later...\n", -rc); /* reschedule for later */ fan_watchdog_reset(); } @@ -8049,8 +7968,7 @@ static int __init fan_init(struct ibm_init_struct *iibm) "secondary fan support enabled\n"); } } else { - printk(TPACPI_ERR - "ThinkPad ACPI EC access misbehaving, " + pr_err("ThinkPad ACPI EC access misbehaving, " "fan status and control unavailable\n"); return 1; } @@ -8150,9 +8068,8 @@ static void fan_suspend(pm_message_t state) fan_control_resume_level = 0; rc = fan_get_status_safe(&fan_control_resume_level); if (rc < 0) - printk(TPACPI_NOTICE - "failed to read fan level for later " - "restore during resume: %d\n", rc); + pr_notice("failed to read fan level for later " + "restore during resume: %d\n", rc); /* if it is undefined, don't attempt to restore it. * KEEP THIS LAST */ @@ -8207,13 +8124,11 @@ static void fan_resume(void) return; } if (do_set) { - printk(TPACPI_NOTICE - "restoring fan level to 0x%02x\n", - fan_control_resume_level); + pr_notice("restoring fan level to 0x%02x\n", + fan_control_resume_level); rc = fan_set_level_safe(fan_control_resume_level); if (rc < 0) - printk(TPACPI_NOTICE - "failed to restore fan level: %d\n", rc); + pr_notice("failed to restore fan level: %d\n", rc); } } @@ -8305,8 +8220,8 @@ static int fan_write_cmd_level(const char *cmd, int *rc) *rc = fan_set_level_safe(level); if (*rc == -ENXIO) - printk(TPACPI_ERR "level command accepted for unsupported " - "access mode %d", fan_control_access_mode); + pr_err("level command accepted for unsupported access mode %d\n", + fan_control_access_mode); else if (!*rc) tpacpi_disclose_usertask("procfs fan", "set level to %d\n", level); @@ -8321,8 +8236,8 @@ static int fan_write_cmd_enable(const char *cmd, int *rc) *rc = fan_set_enable(); if (*rc == -ENXIO) - printk(TPACPI_ERR "enable command accepted for unsupported " - "access mode %d", fan_control_access_mode); + pr_err("enable command accepted for unsupported access mode %d\n", + fan_control_access_mode); else if (!*rc) tpacpi_disclose_usertask("procfs fan", "enable\n"); @@ -8336,8 +8251,8 @@ static int fan_write_cmd_disable(const char *cmd, int *rc) *rc = fan_set_disable(); if (*rc == -ENXIO) - printk(TPACPI_ERR "disable command accepted for unsupported " - "access mode %d", fan_control_access_mode); + pr_err("disable command accepted for unsupported access mode %d\n", + fan_control_access_mode); else if (!*rc) tpacpi_disclose_usertask("procfs fan", "disable\n"); @@ -8356,8 +8271,8 @@ static int fan_write_cmd_speed(const char *cmd, int *rc) *rc = fan_set_speed(speed); if (*rc == -ENXIO) - printk(TPACPI_ERR "speed command accepted for unsupported " - "access mode %d", fan_control_access_mode); + pr_err("speed command accepted for unsupported access mode %d\n", + fan_control_access_mode); else if (!*rc) tpacpi_disclose_usertask("procfs fan", "set speed to %d\n", speed); @@ -8560,8 +8475,8 @@ static int __init ibm_init(struct ibm_init_struct *iibm) if (ibm->acpi->notify) { ret = setup_acpi_notify(ibm); if (ret == -ENODEV) { - printk(TPACPI_NOTICE "disabling subdriver %s\n", - ibm->name); + pr_notice("disabling subdriver %s\n", + ibm->name); ret = 0; goto err_out; } @@ -8583,8 +8498,7 @@ static int __init ibm_init(struct ibm_init_struct *iibm) entry = proc_create_data(ibm->name, mode, proc_dir, &dispatch_proc_fops, ibm); if (!entry) { - printk(TPACPI_ERR "unable to create proc entry %s\n", - ibm->name); + pr_err("unable to create proc entry %s\n", ibm->name); ret = -ENODEV; goto err_out; } @@ -8683,13 +8597,11 @@ static int __must_check __init get_thinkpad_model_data( tp->ec_release = (ec_fw_string[4] << 8) | ec_fw_string[5]; } else { - printk(TPACPI_NOTICE - "ThinkPad firmware release %s " - "doesn't match the known patterns\n", - ec_fw_string); - printk(TPACPI_NOTICE - "please report this to %s\n", - TPACPI_MAIL); + pr_notice("ThinkPad firmware release %s " + "doesn't match the known patterns\n", + ec_fw_string); + pr_notice("please report this to %s\n", + TPACPI_MAIL); } break; } @@ -8733,8 +8645,7 @@ static int __init probe_for_thinkpad(void) tpacpi_acpi_handle_locate("ec", TPACPI_ACPI_EC_HID, &ec_handle); if (!ec_handle) { if (is_thinkpad) - printk(TPACPI_ERR - "Not yet supported ThinkPad detected!\n"); + pr_err("Not yet supported ThinkPad detected!\n"); return -ENODEV; } @@ -8746,10 +8657,10 @@ static int __init probe_for_thinkpad(void) static void __init thinkpad_acpi_init_banner(void) { - printk(TPACPI_INFO "%s v%s\n", TPACPI_DESC, TPACPI_VERSION); - printk(TPACPI_INFO "%s\n", TPACPI_URL); + pr_info("%s v%s\n", TPACPI_DESC, TPACPI_VERSION); + pr_info("%s\n", TPACPI_URL); - printk(TPACPI_INFO "ThinkPad BIOS %s, EC %s\n", + pr_info("ThinkPad BIOS %s, EC %s\n", (thinkpad_id.bios_version_str) ? thinkpad_id.bios_version_str : "unknown", (thinkpad_id.ec_version_str) ? @@ -8758,7 +8669,7 @@ static void __init thinkpad_acpi_init_banner(void) BUG_ON(!thinkpad_id.vendor); if (thinkpad_id.model_str) - printk(TPACPI_INFO "%s %s, model %s\n", + pr_info("%s %s, model %s\n", (thinkpad_id.vendor == PCI_VENDOR_ID_IBM) ? "IBM" : ((thinkpad_id.vendor == PCI_VENDOR_ID_LENOVO) ? @@ -9024,8 +8935,7 @@ static int __init thinkpad_acpi_module_init(void) ret = get_thinkpad_model_data(&thinkpad_id); if (ret) { - printk(TPACPI_ERR - "unable to get DMI data: %d\n", ret); + pr_err("unable to get DMI data: %d\n", ret); thinkpad_acpi_module_exit(); return ret; } @@ -9051,16 +8961,14 @@ static int __init thinkpad_acpi_module_init(void) proc_dir = proc_mkdir(TPACPI_PROC_DIR, acpi_root_dir); if (!proc_dir) { - printk(TPACPI_ERR - "unable to create proc dir " TPACPI_PROC_DIR); + pr_err("unable to create proc dir " TPACPI_PROC_DIR "\n"); thinkpad_acpi_module_exit(); return -ENODEV; } ret = platform_driver_register(&tpacpi_pdriver); if (ret) { - printk(TPACPI_ERR - "unable to register main platform driver\n"); + pr_err("unable to register main platform driver\n"); thinkpad_acpi_module_exit(); return ret; } @@ -9068,8 +8976,7 @@ static int __init thinkpad_acpi_module_init(void) ret = platform_driver_register(&tpacpi_hwmon_pdriver); if (ret) { - printk(TPACPI_ERR - "unable to register hwmon platform driver\n"); + pr_err("unable to register hwmon platform driver\n"); thinkpad_acpi_module_exit(); return ret; } @@ -9082,8 +8989,7 @@ static int __init thinkpad_acpi_module_init(void) &tpacpi_hwmon_pdriver.driver); } if (ret) { - printk(TPACPI_ERR - "unable to create sysfs driver attributes\n"); + pr_err("unable to create sysfs driver attributes\n"); thinkpad_acpi_module_exit(); return ret; } @@ -9096,7 +9002,7 @@ static int __init thinkpad_acpi_module_init(void) if (IS_ERR(tpacpi_pdev)) { ret = PTR_ERR(tpacpi_pdev); tpacpi_pdev = NULL; - printk(TPACPI_ERR "unable to register platform device\n"); + pr_err("unable to register platform device\n"); thinkpad_acpi_module_exit(); return ret; } @@ -9106,16 +9012,14 @@ static int __init thinkpad_acpi_module_init(void) if (IS_ERR(tpacpi_sensors_pdev)) { ret = PTR_ERR(tpacpi_sensors_pdev); tpacpi_sensors_pdev = NULL; - printk(TPACPI_ERR - "unable to register hwmon platform device\n"); + pr_err("unable to register hwmon platform device\n"); thinkpad_acpi_module_exit(); return ret; } ret = device_create_file(&tpacpi_sensors_pdev->dev, &dev_attr_thinkpad_acpi_pdev_name); if (ret) { - printk(TPACPI_ERR - "unable to create sysfs hwmon device attributes\n"); + pr_err("unable to create sysfs hwmon device attributes\n"); thinkpad_acpi_module_exit(); return ret; } @@ -9124,14 +9028,14 @@ static int __init thinkpad_acpi_module_init(void) if (IS_ERR(tpacpi_hwmon)) { ret = PTR_ERR(tpacpi_hwmon); tpacpi_hwmon = NULL; - printk(TPACPI_ERR "unable to register hwmon device\n"); + pr_err("unable to register hwmon device\n"); thinkpad_acpi_module_exit(); return ret; } mutex_init(&tpacpi_inputdev_send_mutex); tpacpi_inputdev = input_allocate_device(); if (!tpacpi_inputdev) { - printk(TPACPI_ERR "unable to allocate input device\n"); + pr_err("unable to allocate input device\n"); thinkpad_acpi_module_exit(); return -ENOMEM; } else { @@ -9163,7 +9067,7 @@ static int __init thinkpad_acpi_module_init(void) ret = input_register_device(tpacpi_inputdev); if (ret < 0) { - printk(TPACPI_ERR "unable to register input device\n"); + pr_err("unable to register input device\n"); thinkpad_acpi_module_exit(); return ret; } else { -- cgit v1.2.3 From bb3ce2020451bdebe5ceac770504f427724008a9 Mon Sep 17 00:00:00 2001 From: Yin Kangkai Date: Wed, 6 Apr 2011 15:05:24 +0100 Subject: platform/oaktrail: ACPI EC Extra driver for Oaktrail This driver implements an Extra ACPI EC driver for products based on Intel Oaktrail platform. This driver does below things: 1. registers itself in the Linux backlight control in /sys/class/backlight/intel_oaktrail/ 2. registers in the rfkill subsystem here: /sys/class/rfkill/rfkillX/ for these components: wifi, bluetooth, wwan (3g), gps Signed-off-by: Yin Kangkai [Extracted from a bigger patch by Yin Kangkai, this version leaves out some sysfs bits that probably want to be driver managed, and ACPI i2c enumeration] Signed-off-by: Alan Cox Signed-off-by: Matthew Garrett --- drivers/platform/x86/Kconfig | 9 + drivers/platform/x86/Makefile | 1 + drivers/platform/x86/intel_oaktrail.c | 396 ++++++++++++++++++++++++++++++++++ 3 files changed, 406 insertions(+) create mode 100644 drivers/platform/x86/intel_oaktrail.c (limited to 'drivers/platform') diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig index 5cb999b50f9..83c2411acb5 100644 --- a/drivers/platform/x86/Kconfig +++ b/drivers/platform/x86/Kconfig @@ -760,4 +760,13 @@ config MXM_WMI MXM is a standard for laptop graphics cards, the WMI interface is required for switchable nvidia graphics machines +config INTEL_OAKTRAIL + tristate "Intel Oaktrail Platform Extras" + depends on ACPI + depends on RFKILL && BACKLIGHT_CLASS_DEVICE && ACPI + ---help--- + Intel Oaktrail platform need this driver to provide interfaces to + enable/disable the Camera, WiFi, BT etc. devices. If in doubt, say Y + here; it will only load on supported platforms. + endif # X86_PLATFORM_DEVICES diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile index a7ab3bc7b3a..af683fb5a80 100644 --- a/drivers/platform/x86/Makefile +++ b/drivers/platform/x86/Makefile @@ -43,3 +43,4 @@ obj-$(CONFIG_IBM_RTL) += ibm_rtl.o obj-$(CONFIG_SAMSUNG_LAPTOP) += samsung-laptop.o obj-$(CONFIG_INTEL_MFLD_THERMAL) += intel_mid_thermal.o obj-$(CONFIG_MXM_WMI) += mxm-wmi.o +obj-$(CONFIG_INTEL_OAKTRAIL) += intel_oaktrail.o diff --git a/drivers/platform/x86/intel_oaktrail.c b/drivers/platform/x86/intel_oaktrail.c new file mode 100644 index 00000000000..e936364a609 --- /dev/null +++ b/drivers/platform/x86/intel_oaktrail.c @@ -0,0 +1,396 @@ +/* + * intel_oaktrail.c - Intel OakTrail Platform support. + * + * Copyright (C) 2010-2011 Intel Corporation + * Author: Yin Kangkai (kangkai.yin@intel.com) + * + * based on Compal driver, Copyright (C) 2008 Cezary Jackiewicz + * , based on MSI driver + * Copyright (C) 2006 Lennart Poettering + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + * This driver does below things: + * 1. registers itself in the Linux backlight control in + * /sys/class/backlight/intel_oaktrail/ + * + * 2. registers in the rfkill subsystem here: /sys/class/rfkill/rfkillX/ + * for these components: wifi, bluetooth, wwan (3g), gps + * + * This driver might work on other products based on Oaktrail. If you + * want to try it you can pass force=1 as argument to the module which + * will force it to load even when the DMI data doesn't identify the + * product as compatible. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + + +#define DRIVER_NAME "intel_oaktrail" +#define DRIVER_VERSION "0.4ac1" + +/* + * This is the devices status address in EC space, and the control bits + * definition: + * + * (1 << 0): Camera enable/disable, RW. + * (1 << 1): Bluetooth enable/disable, RW. + * (1 << 2): GPS enable/disable, RW. + * (1 << 3): WiFi enable/disable, RW. + * (1 << 4): WWAN (3G) enable/disalbe, RW. + * (1 << 5): Touchscreen enable/disable, Read Only. + */ +#define OT_EC_DEVICE_STATE_ADDRESS 0xD6 + +#define OT_EC_CAMERA_MASK (1 << 0) +#define OT_EC_BT_MASK (1 << 1) +#define OT_EC_GPS_MASK (1 << 2) +#define OT_EC_WIFI_MASK (1 << 3) +#define OT_EC_WWAN_MASK (1 << 4) +#define OT_EC_TS_MASK (1 << 5) + +/* + * This is the address in EC space and commands used to control LCD backlight: + * + * Two steps needed to change the LCD backlight: + * 1. write the backlight percentage into OT_EC_BL_BRIGHTNESS_ADDRESS; + * 2. write OT_EC_BL_CONTROL_ON_DATA into OT_EC_BL_CONTROL_ADDRESS. + * + * To read the LCD back light, just read out the value from + * OT_EC_BL_BRIGHTNESS_ADDRESS. + * + * LCD backlight brightness range: 0 - 100 (OT_EC_BL_BRIGHTNESS_MAX) + */ +#define OT_EC_BL_BRIGHTNESS_ADDRESS 0x44 +#define OT_EC_BL_BRIGHTNESS_MAX 100 +#define OT_EC_BL_CONTROL_ADDRESS 0x3A +#define OT_EC_BL_CONTROL_ON_DATA 0x1A + + +static int force; +module_param(force, bool, 0); +MODULE_PARM_DESC(force, "Force driver load, ignore DMI data"); + +static struct platform_device *oaktrail_device; +static struct backlight_device *oaktrail_bl_device; +static struct rfkill *bt_rfkill; +static struct rfkill *gps_rfkill; +static struct rfkill *wifi_rfkill; +static struct rfkill *wwan_rfkill; + + +/* rfkill */ +static int oaktrail_rfkill_set(void *data, bool blocked) +{ + u8 value; + u8 result; + unsigned long radio = (unsigned long) data; + + ec_read(OT_EC_DEVICE_STATE_ADDRESS, &result); + + if (!blocked) + value = (u8) (result | radio); + else + value = (u8) (result & ~radio); + + ec_write(OT_EC_DEVICE_STATE_ADDRESS, value); + + return 0; +} + +static const struct rfkill_ops oaktrail_rfkill_ops = { + .set_block = oaktrail_rfkill_set, +}; + +static struct rfkill *oaktrail_rfkill_new(char *name, enum rfkill_type type, + unsigned long mask) +{ + struct rfkill *rfkill_dev; + u8 value; + int err; + + rfkill_dev = rfkill_alloc(name, &oaktrail_device->dev, type, + &oaktrail_rfkill_ops, (void *)mask); + if (!rfkill_dev) + return ERR_PTR(-ENOMEM); + + ec_read(OT_EC_DEVICE_STATE_ADDRESS, &value); + rfkill_init_sw_state(rfkill_dev, (value & mask) != 1); + + err = rfkill_register(rfkill_dev); + if (err) { + rfkill_destroy(rfkill_dev); + return ERR_PTR(err); + } + + return rfkill_dev; +} + +static inline void __oaktrail_rfkill_cleanup(struct rfkill *rf) +{ + if (rf) { + rfkill_unregister(rf); + rfkill_destroy(rf); + } +} + +static void oaktrail_rfkill_cleanup(void) +{ + __oaktrail_rfkill_cleanup(wifi_rfkill); + __oaktrail_rfkill_cleanup(bt_rfkill); + __oaktrail_rfkill_cleanup(gps_rfkill); + __oaktrail_rfkill_cleanup(wwan_rfkill); +} + +static int oaktrail_rfkill_init(void) +{ + int ret; + + wifi_rfkill = oaktrail_rfkill_new("oaktrail-wifi", + RFKILL_TYPE_WLAN, + OT_EC_WIFI_MASK); + if (IS_ERR(wifi_rfkill)) { + ret = PTR_ERR(wifi_rfkill); + wifi_rfkill = NULL; + goto cleanup; + } + + bt_rfkill = oaktrail_rfkill_new("oaktrail-bluetooth", + RFKILL_TYPE_BLUETOOTH, + OT_EC_BT_MASK); + if (IS_ERR(bt_rfkill)) { + ret = PTR_ERR(bt_rfkill); + bt_rfkill = NULL; + goto cleanup; + } + + gps_rfkill = oaktrail_rfkill_new("oaktrail-gps", + RFKILL_TYPE_GPS, + OT_EC_GPS_MASK); + if (IS_ERR(gps_rfkill)) { + ret = PTR_ERR(gps_rfkill); + gps_rfkill = NULL; + goto cleanup; + } + + wwan_rfkill = oaktrail_rfkill_new("oaktrail-wwan", + RFKILL_TYPE_WWAN, + OT_EC_WWAN_MASK); + if (IS_ERR(wwan_rfkill)) { + ret = PTR_ERR(wwan_rfkill); + wwan_rfkill = NULL; + goto cleanup; + } + + return 0; + +cleanup: + oaktrail_rfkill_cleanup(); + return ret; +} + + +/* backlight */ +static int get_backlight_brightness(struct backlight_device *b) +{ + u8 value; + ec_read(OT_EC_BL_BRIGHTNESS_ADDRESS, &value); + + return value; +} + +static int set_backlight_brightness(struct backlight_device *b) +{ + u8 percent = (u8) b->props.brightness; + if (percent < 0 || percent > OT_EC_BL_BRIGHTNESS_MAX) + return -EINVAL; + + ec_write(OT_EC_BL_BRIGHTNESS_ADDRESS, percent); + ec_write(OT_EC_BL_CONTROL_ADDRESS, OT_EC_BL_CONTROL_ON_DATA); + + return 0; +} + +static const struct backlight_ops oaktrail_bl_ops = { + .get_brightness = get_backlight_brightness, + .update_status = set_backlight_brightness, +}; + +static int oaktrail_backlight_init(void) +{ + struct backlight_device *bd; + struct backlight_properties props; + + memset(&props, 0, sizeof(struct backlight_properties)); + props.max_brightness = OT_EC_BL_BRIGHTNESS_MAX; + bd = backlight_device_register(DRIVER_NAME, + &oaktrail_device->dev, NULL, + &oaktrail_bl_ops, + &props); + + if (IS_ERR(bd)) { + oaktrail_bl_device = NULL; + pr_warning("Unable to register backlight device\n"); + return PTR_ERR(bd); + } + + oaktrail_bl_device = bd; + + bd->props.brightness = get_backlight_brightness(bd); + bd->props.power = FB_BLANK_UNBLANK; + backlight_update_status(bd); + + return 0; +} + +static void oaktrail_backlight_exit(void) +{ + if (oaktrail_bl_device) + backlight_device_unregister(oaktrail_bl_device); +} + +static int __devinit oaktrail_probe(struct platform_device *pdev) +{ + return 0; +} + +static int __devexit oaktrail_remove(struct platform_device *pdev) +{ + return 0; +} + +static struct platform_driver oaktrail_driver = { + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + }, + .probe = oaktrail_probe, + .remove = __devexit_p(oaktrail_remove) +}; + +static int dmi_check_cb(const struct dmi_system_id *id) +{ + pr_info("Identified model '%s'\n", id->ident); + return 0; +} + +static struct dmi_system_id __initdata oaktrail_dmi_table[] = { + { + .ident = "OakTrail platform", + .matches = { + DMI_MATCH(DMI_PRODUCT_NAME, "OakTrail platform"), + }, + .callback = dmi_check_cb + }, + { } +}; + +static int __init oaktrail_init(void) +{ + int ret; + + if (acpi_disabled) { + pr_err("ACPI needs to be enabled for this driver to work!\n"); + return -ENODEV; + } + + if (!force && !dmi_check_system(oaktrail_dmi_table)) { + pr_err("Platform not recognized (You could try the module's force-parameter)"); + return -ENODEV; + } + + ret = platform_driver_register(&oaktrail_driver); + if (ret) { + pr_warning("Unable to register platform driver\n"); + goto err_driver_reg; + } + + oaktrail_device = platform_device_alloc(DRIVER_NAME, -1); + if (!oaktrail_device) { + pr_warning("Unable to allocate platform device\n"); + ret = -ENOMEM; + goto err_device_alloc; + } + + ret = platform_device_add(oaktrail_device); + if (ret) { + pr_warning("Unable to add platform device\n"); + goto err_device_add; + } + + if (!acpi_video_backlight_support()) { + ret = oaktrail_backlight_init(); + if (ret) + goto err_backlight; + + } else + pr_info("Backlight controlled by ACPI video driver\n"); + + ret = oaktrail_rfkill_init(); + if (ret) { + pr_warning("Setup rfkill failed\n"); + goto err_rfkill; + } + + pr_info("Driver "DRIVER_VERSION" successfully loaded\n"); + return 0; + +err_rfkill: + oaktrail_backlight_exit(); +err_backlight: + platform_device_del(oaktrail_device); +err_device_add: + platform_device_put(oaktrail_device); +err_device_alloc: + platform_driver_unregister(&oaktrail_driver); +err_driver_reg: + + return ret; +} + +static void __exit oaktrail_cleanup(void) +{ + oaktrail_backlight_exit(); + oaktrail_rfkill_cleanup(); + platform_device_unregister(oaktrail_device); + platform_driver_unregister(&oaktrail_driver); + + pr_info("Driver unloaded\n"); +} + +module_init(oaktrail_init); +module_exit(oaktrail_cleanup); + +MODULE_AUTHOR("Yin Kangkai (kangkai.yin@intel.com)"); +MODULE_DESCRIPTION("Intel Oaktrail Platform ACPI Extras"); +MODULE_VERSION(DRIVER_VERSION); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("dmi:*:svnIntelCorporation:pnOakTrailplatform:*"); -- cgit v1.2.3 From c2647b5e99c8ff1b3f535c7c84564cdc53214edf Mon Sep 17 00:00:00 2001 From: "Lee, Chun-Yi" Date: Fri, 15 Apr 2011 18:42:47 +0800 Subject: acer-wmi: does not allow negative number set to initial device state The driver set module parameter value: mailled, threeg and brightness to BIOS by evaluate wmi method when driver was initialed. The default values for those parameters are -1, so, that will be better don't set negative value to BIOS. Cc: Carlos Corbacho Cc: Matthew Garrett Cc: Dmitry Torokhov Cc: Corentin Chary Signed-off-by: Lee, Chun-Yi Signed-off-by: Matthew Garrett --- drivers/platform/x86/acer-wmi.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index fa8fa73f543..0682ecb3074 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -961,10 +961,12 @@ static void __init acer_commandline_init(void) * These will all fail silently if the value given is invalid, or the * capability isn't available on the given interface */ - set_u32(mailled, ACER_CAP_MAILLED); - if (!has_type_aa) + if (mailled >= 0) + set_u32(mailled, ACER_CAP_MAILLED); + if (!has_type_aa && threeg >= 0) set_u32(threeg, ACER_CAP_THREEG); - set_u32(brightness, ACER_CAP_BRIGHTNESS); + if (brightness >= 0) + set_u32(brightness, ACER_CAP_BRIGHTNESS); } /* -- cgit v1.2.3 From e569b223d53cb2720f55be72932f5758a056ff6d Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 24 Apr 2011 11:00:08 +0200 Subject: acerhdf: Drop pointless dependency on THERMAL_HWMON The THERMAL_HWMON config option simply exposes the thermal zone temperature values and limits to user-space. It makes no sense for a kernel driver to depend on this. Signed-off-by: Jean Delvare Cc: Peter Feuerer Cc: Matthew Garrett Signed-off-by: Matthew Garrett --- drivers/platform/x86/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig index 83c2411acb5..45e0191c35d 100644 --- a/drivers/platform/x86/Kconfig +++ b/drivers/platform/x86/Kconfig @@ -39,7 +39,7 @@ config ACER_WMI config ACERHDF tristate "Acer Aspire One temperature and fan driver" - depends on THERMAL && THERMAL_HWMON && ACPI + depends on THERMAL && ACPI ---help--- This is a driver for Acer Aspire One netbooks. It allows to access the temperature sensor and to control the fan. -- cgit v1.2.3 From c4bae98c4f913d3220d185c47d8817b5e2bba007 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 24 Apr 2011 18:07:55 +0200 Subject: acerhdf: Clean up includes * The acerhdf driver isn't an ACPI driver, so it needs not include . All it uses is ec_read() and ec_write(), for which is sufficient. * I couldn't find any reason why and were included. This should avoid unneeded rebuilds of the acerhdf driver. Signed-off-by: Jean Delvare Cc: Peter Feuerer Cc: Matthew Garrett Signed-off-by: Matthew Garrett --- drivers/platform/x86/acerhdf.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/acerhdf.c b/drivers/platform/x86/acerhdf.c index 60f9cfcac93..fca3489218b 100644 --- a/drivers/platform/x86/acerhdf.c +++ b/drivers/platform/x86/acerhdf.c @@ -35,10 +35,8 @@ #include #include -#include #include -#include -#include +#include #include #include -- cgit v1.2.3 From b9e066942981c6de3897de94953bea295ae18ec8 Mon Sep 17 00:00:00 2001 From: Ameya Palande <2ameya@gmail.com> Date: Wed, 6 Apr 2011 17:44:37 +0300 Subject: platform/x86: Simplify intel_mid_powerbtn This patch: 1. Removes unnecessay #defines 2. Removes 'mfld_pb_priv' data structure which results in simpler error handling and less memory allocations. Signed-off-by: Ameya Palande <2ameya@gmail.com> Signed-off-by: Matthew Garrett --- drivers/platform/x86/intel_mid_powerbtn.c | 72 +++++++++++++------------------ 1 file changed, 30 insertions(+), 42 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/intel_mid_powerbtn.c b/drivers/platform/x86/intel_mid_powerbtn.c index 213e79ba68d..f1ae5078b7e 100644 --- a/drivers/platform/x86/intel_mid_powerbtn.c +++ b/drivers/platform/x86/intel_mid_powerbtn.c @@ -23,58 +23,48 @@ #include #include #include + #include #define DRIVER_NAME "msic_power_btn" -#define MSIC_IRQ_STAT 0x02 - #define MSIC_IRQ_PB (1 << 0) -#define MSIC_PB_CONFIG 0x3e #define MSIC_PB_STATUS 0x3f - #define MSIC_PB_LEVEL (1 << 3) /* 1 - release, 0 - press */ - -struct mfld_pb_priv { - struct input_dev *input; - unsigned int irq; -}; +#define MSIC_PB_LEVEL (1 << 3) /* 1 - release, 0 - press */ static irqreturn_t mfld_pb_isr(int irq, void *dev_id) { - struct mfld_pb_priv *priv = dev_id; + struct input_dev *input = dev_id; int ret; u8 pbstat; ret = intel_scu_ipc_ioread8(MSIC_PB_STATUS, &pbstat); - if (ret < 0) - return IRQ_HANDLED; - - input_event(priv->input, EV_KEY, KEY_POWER, !(pbstat & MSIC_PB_LEVEL)); - input_sync(priv->input); + if (ret < 0) { + dev_err(input->dev.parent, "Read error %d while reading" + " MSIC_PB_STATUS\n", ret); + } else { + input_event(input, EV_KEY, KEY_POWER, + !(pbstat & MSIC_PB_LEVEL)); + input_sync(input); + } return IRQ_HANDLED; } static int __devinit mfld_pb_probe(struct platform_device *pdev) { - struct mfld_pb_priv *priv; struct input_dev *input; - int irq; + int irq = platform_get_irq(pdev, 0); int error; - irq = platform_get_irq(pdev, 0); if (irq < 0) return -EINVAL; - priv = kzalloc(sizeof(struct mfld_pb_priv), GFP_KERNEL); input = input_allocate_device(); - if (!priv || !input) { - error = -ENOMEM; - goto err_free_mem; + if (!input) { + dev_err(&pdev->dev, "Input device allocation error\n"); + return -ENOMEM; } - priv->input = input; - priv->irq = irq; - input->name = pdev->name; input->phys = "power-button/input0"; input->id.bustype = BUS_HOST; @@ -82,42 +72,40 @@ static int __devinit mfld_pb_probe(struct platform_device *pdev) input_set_capability(input, EV_KEY, KEY_POWER); - error = request_threaded_irq(priv->irq, NULL, mfld_pb_isr, - 0, DRIVER_NAME, priv); + error = request_threaded_irq(irq, NULL, mfld_pb_isr, 0, + DRIVER_NAME, input); if (error) { - dev_err(&pdev->dev, - "unable to request irq %d for mfld power button\n", - irq); - goto err_free_mem; + dev_err(&pdev->dev, "Unable to request irq %d for mfld power" + "button\n", irq); + goto err_free_input; } error = input_register_device(input); if (error) { - dev_err(&pdev->dev, - "unable to register input dev, error %d\n", error); + dev_err(&pdev->dev, "Unable to register input dev, error " + "%d\n", error); goto err_free_irq; } - platform_set_drvdata(pdev, priv); + platform_set_drvdata(pdev, input); return 0; err_free_irq: - free_irq(priv->irq, priv); -err_free_mem: + free_irq(irq, input); +err_free_input: input_free_device(input); - kfree(priv); return error; } static int __devexit mfld_pb_remove(struct platform_device *pdev) { - struct mfld_pb_priv *priv = platform_get_drvdata(pdev); - - free_irq(priv->irq, priv); - input_unregister_device(priv->input); - kfree(priv); + struct input_dev *input = platform_get_drvdata(pdev); + int irq = platform_get_irq(pdev, 0); + free_irq(irq, input); + input_unregister_device(input); platform_set_drvdata(pdev, NULL); + return 0; } -- cgit v1.2.3 From cb8b646d8b27053d311595b4fc7dbe161d92683e Mon Sep 17 00:00:00 2001 From: Ameya Palande <2ameya@gmail.com> Date: Wed, 6 Apr 2011 17:45:03 +0300 Subject: platform/x86: Fix Makefile for intel_mid_powerbtn Signed-off-by: Ameya Palande <2ameya@gmail.com> Signed-off-by: Matthew Garrett --- drivers/platform/x86/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile index af683fb5a80..afc1f832aa6 100644 --- a/drivers/platform/x86/Makefile +++ b/drivers/platform/x86/Makefile @@ -41,6 +41,6 @@ obj-$(CONFIG_XO1_RFKILL) += xo1-rfkill.o obj-$(CONFIG_XO15_EBOOK) += xo15-ebook.o obj-$(CONFIG_IBM_RTL) += ibm_rtl.o obj-$(CONFIG_SAMSUNG_LAPTOP) += samsung-laptop.o -obj-$(CONFIG_INTEL_MFLD_THERMAL) += intel_mid_thermal.o obj-$(CONFIG_MXM_WMI) += mxm-wmi.o +obj-$(CONFIG_INTEL_MID_POWER_BUTTON) += intel_mid_powerbtn.o obj-$(CONFIG_INTEL_OAKTRAIL) += intel_oaktrail.o -- cgit v1.2.3 From 239dca9e9aff6630c22fef696978ba3a878f7d96 Mon Sep 17 00:00:00 2001 From: Ameya Palande <2ameya@gmail.com> Date: Thu, 7 Apr 2011 16:30:02 +0300 Subject: platform-x86: intel_mid_thermal: Fix memory leak Signed-off-by: Ameya Palande <2ameya@gmail.com> Signed-off-by: Matthew Garrett --- drivers/platform/x86/intel_mid_thermal.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/intel_mid_thermal.c b/drivers/platform/x86/intel_mid_thermal.c index f0776504521..3a578323122 100644 --- a/drivers/platform/x86/intel_mid_thermal.c +++ b/drivers/platform/x86/intel_mid_thermal.c @@ -527,6 +527,7 @@ static int mid_thermal_remove(struct platform_device *pdev) for (i = 0; i < MSIC_THERMAL_SENSORS; i++) thermal_zone_device_unregister(pinfo->tzd[i]); + kfree(pinfo); platform_set_drvdata(pdev, NULL); /* Stop the ADC */ -- cgit v1.2.3 From 8ae68de15d5ddaa8d41e197a730e19223adab2e1 Mon Sep 17 00:00:00 2001 From: Melchior FRANZ Date: Tue, 24 May 2011 10:35:55 +0200 Subject: support wlan hotkey on Acer Travelmate 5735Z On an Acer Travelmate 5735Z-452G32Mnss the WLAN-enable/disable key doesn't send 0x1 as acpi event key code, but 0x3. This patch also makes the module ignore hotkey acpi events for functions that are already handled without. This avoids warning message "keyboard: can't emulate rawmode for keycode 240". Signed-off-by: Melchior FRANZ Signed-off-by: Matthew Garrett --- drivers/platform/x86/acer-wmi.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index 0682ecb3074..57c6c8a4db2 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -98,13 +98,26 @@ enum acer_wmi_event_ids { static const struct key_entry acer_wmi_keymap[] = { {KE_KEY, 0x01, {KEY_WLAN} }, /* WiFi */ + {KE_KEY, 0x03, {KEY_WLAN} }, /* WiFi */ {KE_KEY, 0x12, {KEY_BLUETOOTH} }, /* BT */ {KE_KEY, 0x21, {KEY_PROG1} }, /* Backup */ {KE_KEY, 0x22, {KEY_PROG2} }, /* Arcade */ {KE_KEY, 0x23, {KEY_PROG3} }, /* P_Key */ {KE_KEY, 0x24, {KEY_PROG4} }, /* Social networking_Key */ + {KE_IGNORE, 0x41, {KEY_MUTE} }, + {KE_IGNORE, 0x42, {KEY_PREVIOUSSONG} }, + {KE_IGNORE, 0x43, {KEY_NEXTSONG} }, + {KE_IGNORE, 0x44, {KEY_PLAYPAUSE} }, + {KE_IGNORE, 0x45, {KEY_STOP} }, + {KE_IGNORE, 0x48, {KEY_VOLUMEUP} }, + {KE_IGNORE, 0x49, {KEY_VOLUMEDOWN} }, + {KE_IGNORE, 0x61, {KEY_SWITCHVIDEOMODE} }, + {KE_IGNORE, 0x62, {KEY_BRIGHTNESSUP} }, + {KE_IGNORE, 0x63, {KEY_BRIGHTNESSDOWN} }, {KE_KEY, 0x64, {KEY_SWITCHVIDEOMODE} }, /* Display Switch */ + {KE_IGNORE, 0x81, {KEY_SLEEP} }, {KE_KEY, 0x82, {KEY_TOUCHPAD_TOGGLE} }, /* Touch Pad On/Off */ + {KE_IGNORE, 0x83, {KEY_TOUCHPAD_TOGGLE} }, {KE_END, 0} }; @@ -1345,7 +1358,7 @@ static void acer_wmi_notify(u32 value, void *context) case WMID_HOTKEY_EVENT: if (return_value.device_state) { u16 device_state = return_value.device_state; - pr_debug("deivces states: 0x%x\n", device_state); + pr_debug("device state: 0x%x\n", device_state); if (has_cap(ACER_CAP_WIRELESS)) rfkill_set_sw_state(wireless_rfkill, !(device_state & ACER_WMID3_GDS_WIRELESS)); -- cgit v1.2.3 From 5ddf9c5fa5a78036790ed72aaed3b84ee7dd4532 Mon Sep 17 00:00:00 2001 From: Weiping Pan Date: Mon, 16 May 2011 14:49:47 +0800 Subject: platform/x86:delete two unused variables variable handle is not used in these two functions, just delete them. Signed-off-by: Weiping Pan Signed-off-by: Matthew Garrett --- drivers/platform/x86/sony-laptop.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/sony-laptop.c b/drivers/platform/x86/sony-laptop.c index 12dd0a62f30..bbd182e178c 100644 --- a/drivers/platform/x86/sony-laptop.c +++ b/drivers/platform/x86/sony-laptop.c @@ -962,7 +962,6 @@ static int sony_backlight_get_brightness(struct backlight_device *bd) static int sony_nc_get_brightness_ng(struct backlight_device *bd) { int result; - int *handle = (int *)bl_get_data(bd); struct sony_backlight_props *sdev = (struct sony_backlight_props *)bl_get_data(bd); @@ -974,7 +973,6 @@ static int sony_nc_get_brightness_ng(struct backlight_device *bd) static int sony_nc_update_status_ng(struct backlight_device *bd) { int value, result; - int *handle = (int *)bl_get_data(bd); struct sony_backlight_props *sdev = (struct sony_backlight_props *)bl_get_data(bd); -- cgit v1.2.3 From a8d1a266eee5f8b822449fe19d1735189377ef47 Mon Sep 17 00:00:00 2001 From: "Lee, Chun-Yi" Date: Sun, 22 May 2011 07:33:52 +0800 Subject: acer-wmi: check the existence of internal 3G device when set capability That will be better to check the existence of internal 3G device when we set threeg capability and generate killswitch for threeg. It can avoid userland access 3G rfkill but the machine doesn't have internal 3G device. Reference: bko#32862 https://bugzilla.kernel.org/show_bug.cgi?id=32862 Tested on Acer Aspire 8930G, Acer Travelmate 8572 Tested-by: Hector Martin Cc: Carlos Corbacho Cc: Matthew Garrett Cc: Dmitry Torokhov Cc: Corentin Chary Cc: Thomas Renninger Signed-off-by: Lee, Chun-Yi Signed-off-by: Matthew Garrett --- drivers/platform/x86/acer-wmi.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index 57c6c8a4db2..92ee4d63727 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -889,7 +889,8 @@ static acpi_status WMID_set_capabilities(void) dmi_walk(type_aa_dmi_decode, NULL); if (!has_type_aa) { interface->capability |= ACER_CAP_WIRELESS; - interface->capability |= ACER_CAP_THREEG; + if (devices & 0x40) + interface->capability |= ACER_CAP_THREEG; if (devices & 0x10) interface->capability |= ACER_CAP_BLUETOOTH; } -- cgit v1.2.3 From ab6a931620cfa5c565b351d1982306c3c8b97f96 Mon Sep 17 00:00:00 2001 From: "Lee, Chun-Yi" Date: Sun, 22 May 2011 07:33:53 +0800 Subject: acer-wmi: allow 64-bits return buffer from WMI methods Acer WMID_GUID1/2 method's return buffer was declared to 64-bits on some Acer notebook, but WMI method only use 32-bits in return buffer. So, add this patch for allow 64-bits return buffer. Reference: bko#34142 https://bugzilla.kernel.org/show_bug.cgi?id=34142 Tested on Acer Travelmate 5735Z-452G32Mnss Tested-by: Melchior FRANZ Cc: Carlos Corbacho Cc: Matthew Garrett Cc: Dmitry Torokhov Cc: Corentin Chary Cc: Thomas Renninger Signed-off-by: Lee, Chun-Yi Signed-off-by: Matthew Garrett --- drivers/platform/x86/acer-wmi.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index 92ee4d63727..48219117823 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -750,7 +750,8 @@ WMI_execute_u32(u32 method_id, u32 in, u32 *out) obj = (union acpi_object *) result.pointer; if (obj && obj->type == ACPI_TYPE_BUFFER && - obj->buffer.length == sizeof(u32)) { + (obj->buffer.length == sizeof(u32) || + obj->buffer.length == sizeof(u64))) { tmp = *((u32 *) obj->buffer.pointer); } else { tmp = 0; @@ -879,7 +880,8 @@ static acpi_status WMID_set_capabilities(void) obj = (union acpi_object *) out.pointer; if (obj && obj->type == ACPI_TYPE_BUFFER && - obj->buffer.length == sizeof(u32)) { + (obj->buffer.length == sizeof(u32) || + obj->buffer.length == sizeof(u64))) { devices = *((u32 *) obj->buffer.pointer); } else { kfree(out.pointer); @@ -1522,7 +1524,8 @@ static u32 get_wmid_devices(void) obj = (union acpi_object *) out.pointer; if (obj && obj->type == ACPI_TYPE_BUFFER && - obj->buffer.length == sizeof(u32)) { + (obj->buffer.length == sizeof(u32) || + obj->buffer.length == sizeof(u64))) { devices = *((u32 *) obj->buffer.pointer); } -- cgit v1.2.3 From 6d88ff0f8ef3529f68233d3963b2a7e07f8e4f69 Mon Sep 17 00:00:00 2001 From: "Lee, Chun-Yi" Date: Sun, 22 May 2011 07:33:54 +0800 Subject: acer-wmi: support to set communication device state by new wmid method Have many Acer notebooks' BIOS already support new WMID_GUID3 method. On those machines, that will be better set communication device by evaluate WMID_GUID3 method. Tested on Acer Travelmate 8572 Cc: Carlos Corbacho Cc: Matthew Garrett Cc: Dmitry Torokhov Cc: Corentin Chary Cc: Thomas Renninger Signed-off-by: Lee, Chun-Yi Signed-off-by: Matthew Garrett --- drivers/platform/x86/acer-wmi.c | 111 +++++++++++++++++++++++++++++++++++++++- 1 file changed, 110 insertions(+), 1 deletion(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index 48219117823..5dc843bfc6c 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -135,6 +135,7 @@ struct event_return_value { */ #define ACER_WMID3_GDS_WIRELESS (1<<0) /* WiFi */ #define ACER_WMID3_GDS_THREEG (1<<6) /* 3G */ +#define ACER_WMID3_GDS_WIMAX (1<<7) /* WiMAX */ #define ACER_WMID3_GDS_BLUETOOTH (1<<11) /* BT */ struct lm_input_params { @@ -1142,6 +1143,114 @@ static acpi_status get_device_status(u32 *value, u32 cap) } } +static acpi_status wmid3_set_device_status(u32 value, u16 device) +{ + struct wmid3_gds_return_value return_value; + acpi_status status; + union acpi_object *obj; + u16 devices; + struct wmid3_gds_input_param params = { + .function_num = 0x1, + .hotkey_number = 0x01, + .devices = ACER_WMID3_GDS_WIRELESS & + ACER_WMID3_GDS_THREEG & + ACER_WMID3_GDS_WIMAX & + ACER_WMID3_GDS_BLUETOOTH, + }; + struct acpi_buffer input = { + sizeof(struct wmid3_gds_input_param), + ¶ms + }; + struct acpi_buffer output = { ACPI_ALLOCATE_BUFFER, NULL }; + struct acpi_buffer output2 = { ACPI_ALLOCATE_BUFFER, NULL }; + + status = wmi_evaluate_method(WMID_GUID3, 0, 0x2, &input, &output); + if (ACPI_FAILURE(status)) + return status; + + obj = output.pointer; + + if (!obj) + return AE_ERROR; + else if (obj->type != ACPI_TYPE_BUFFER) { + kfree(obj); + return AE_ERROR; + } + if (obj->buffer.length != 8) { + pr_warning("Unknown buffer length %d\n", obj->buffer.length); + kfree(obj); + return AE_ERROR; + } + + return_value = *((struct wmid3_gds_return_value *)obj->buffer.pointer); + kfree(obj); + + if (return_value.error_code || return_value.ec_return_value) { + pr_warning("Get Current Device Status failed: " + "0x%x - 0x%x\n", return_value.error_code, + return_value.ec_return_value); + return status; + } + + devices = return_value.devices; + params.function_num = 0x2; + params.hotkey_number = 0x01; + params.devices = (value) ? (devices | device) : (devices & ~device); + + status = wmi_evaluate_method(WMID_GUID3, 0, 0x1, &input, &output2); + if (ACPI_FAILURE(status)) + return status; + + obj = output2.pointer; + + if (!obj) + return AE_ERROR; + else if (obj->type != ACPI_TYPE_BUFFER) { + kfree(obj); + return AE_ERROR; + } + if (obj->buffer.length != 4) { + pr_warning("Unknown buffer length %d\n", obj->buffer.length); + kfree(obj); + return AE_ERROR; + } + + return_value = *((struct wmid3_gds_return_value *)obj->buffer.pointer); + kfree(obj); + + if (return_value.error_code || return_value.ec_return_value) + pr_warning("Set Device Status failed: " + "0x%x - 0x%x\n", return_value.error_code, + return_value.ec_return_value); + + return status; +} + +static acpi_status set_device_status(u32 value, u32 cap) +{ + if (wmi_has_guid(WMID_GUID3)) { + u16 device; + + switch (cap) { + case ACER_CAP_WIRELESS: + device = ACER_WMID3_GDS_WIRELESS; + break; + case ACER_CAP_BLUETOOTH: + device = ACER_WMID3_GDS_BLUETOOTH; + break; + case ACER_CAP_THREEG: + device = ACER_WMID3_GDS_THREEG; + break; + default: + return AE_ERROR; + } + return wmid3_set_device_status(value, device); + + } else { + return set_u32(value, cap); + } +} + /* * Rfkill devices */ @@ -1178,7 +1287,7 @@ static int acer_rfkill_set(void *data, bool blocked) u32 cap = (unsigned long)data; if (rfkill_inited) { - status = set_u32(!blocked, cap); + status = set_device_status(!blocked, cap); if (ACPI_FAILURE(status)) return -ENODEV; } -- cgit v1.2.3 From d436514e21b827ab602d1714028c34179c42d09f Mon Sep 17 00:00:00 2001 From: "Lee, Chun-Yi" Date: Thu, 26 May 2011 11:09:19 +0800 Subject: msi-laptop: fix section mismatch in reference from the function load_scm_model_init There have section mismatch warning message shows up when building the kernel with make CONFIG_DEBUG_SECTION_MISMATCH=y. The problem is the load_scm_model_init() calls msi_laptop_input_setup() which is an __init function, but load_scm_model_init() lacks a __init annotation. This patch add __init on load_scm_model_init() to avoid warning message. Cc: Matthew Garrett Cc: Dmitry Torokhov Cc: Corentin Chary Cc: Thomas Renninger Signed-off-by: Lee, Chun-Yi Signed-off-by: Matthew Garrett --- drivers/platform/x86/msi-laptop.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/msi-laptop.c b/drivers/platform/x86/msi-laptop.c index f89c0b6a9ae..d7213e40686 100644 --- a/drivers/platform/x86/msi-laptop.c +++ b/drivers/platform/x86/msi-laptop.c @@ -800,7 +800,7 @@ static void msi_laptop_input_destroy(void) input_unregister_device(msi_laptop_input_dev); } -static int load_scm_model_init(struct platform_device *sdev) +static int __init load_scm_model_init(struct platform_device *sdev) { u8 data; int result; -- cgit v1.2.3 From 987dfbaa65b2c3568b85e29d2598da08a011ee09 Mon Sep 17 00:00:00 2001 From: "Lee, Chun-Yi" Date: Fri, 27 May 2011 14:52:14 +0800 Subject: acer-wmi: support integer return type from WMI methods Acer WMID_GUID1/2 method's return value was declared to integer type on Gateway notebook. So, add this patch for support integer return type. Reference: bko#33032 https://bugzilla.kernel.org/show_bug.cgi?id=33032 Tested on Gateway NV5909H laptop Tested-by: Filipus Klutiero Cc: Carlos Corbacho Cc: Matthew Garrett Cc: Dmitry Torokhov Cc: Corentin Chary Cc: Thomas Renninger Signed-off-by: Lee, Chun-Yi Signed-off-by: Matthew Garrett --- drivers/platform/x86/acer-wmi.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers/platform') diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index 5dc843bfc6c..005417bd429 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -754,6 +754,8 @@ WMI_execute_u32(u32 method_id, u32 in, u32 *out) (obj->buffer.length == sizeof(u32) || obj->buffer.length == sizeof(u64))) { tmp = *((u32 *) obj->buffer.pointer); + } else if (obj->type == ACPI_TYPE_INTEGER) { + tmp = (u32) obj->integer.value; } else { tmp = 0; } @@ -884,6 +886,8 @@ static acpi_status WMID_set_capabilities(void) (obj->buffer.length == sizeof(u32) || obj->buffer.length == sizeof(u64))) { devices = *((u32 *) obj->buffer.pointer); + } else if (obj->type == ACPI_TYPE_INTEGER) { + devices = (u32) obj->integer.value; } else { kfree(out.pointer); return AE_ERROR; @@ -1636,6 +1640,8 @@ static u32 get_wmid_devices(void) (obj->buffer.length == sizeof(u32) || obj->buffer.length == sizeof(u64))) { devices = *((u32 *) obj->buffer.pointer); + } else if (obj->type == ACPI_TYPE_INTEGER) { + devices = (u32) obj->integer.value; } kfree(out.pointer); -- cgit v1.2.3