diff options
Diffstat (limited to 'drivers/net/wireless/orinoco_plx.c')
| -rw-r--r-- | drivers/net/wireless/orinoco_plx.c | 223 |
1 files changed, 96 insertions, 127 deletions
diff --git a/drivers/net/wireless/orinoco_plx.c b/drivers/net/wireless/orinoco_plx.c index 210e7377654..84f696c7755 100644 --- a/drivers/net/wireless/orinoco_plx.c +++ b/drivers/net/wireless/orinoco_plx.c @@ -3,7 +3,7 @@ * Driver for Prism II devices which would usually be driven by orinoco_cs, * but are connected to the PCI bus by a PLX9052. * - * Current maintainers (as of 29 September 2003) are: + * Current maintainers are: * Pavel Roskin <proski AT gnu.org> * and David Gibson <hermes AT gibson.dropbear.id.au> * @@ -30,38 +30,18 @@ * other provisions required by the GPL. If you do not delete the * provisions above, a recipient may use your version of this file * under either the MPL or the GPL. - - * Caution: this is experimental and probably buggy. For success and - * failure reports for different cards and adaptors, see - * orinoco_plx_pci_id_table near the end of the file. If you have a - * card we don't have the PCI id for, and looks like it should work, - * drop me mail with the id and "it works"/"it doesn't work". - * - * Note: if everything gets detected fine but it doesn't actually send - * or receive packets, your first port of call should probably be to - * try newer firmware in the card. Especially if you're doing Ad-Hoc - * modes. - * - * The actual driving is done by orinoco.c, this is just resource - * allocation stuff. The explanation below is courtesy of Ryan Niemi - * on the linux-wlan-ng list at - * http://archives.neohapsis.com/archives/dev/linux-wlan/2001-q1/0026.html * - * The PLX9052-based cards (WL11000 and several others) are a - * different beast than the usual PCMCIA-based PRISM2 configuration - * expected by wlan-ng. Here's the general details on how the WL11000 - * PCI adapter works: + * Here's the general details on how the PLX9052 adapter works: * * - Two PCI I/O address spaces, one 0x80 long which contains the * PLX9052 registers, and one that's 0x40 long mapped to the PCMCIA * slot I/O address space. * - * - One PCI memory address space, mapped to the PCMCIA memory space + * - One PCI memory address space, mapped to the PCMCIA attribute space * (containing the CIS). * - * After identifying the I/O and memory space, you can read through - * the memory space to confirm the CIS's device ID or manufacturer ID - * to make sure it's the expected card. qKeep in mind that the PCMCIA + * Using the later, you can read through the CIS data to make sure the + * card is compatible with the driver. Keep in mind that the PCMCIA * spec specifies the CIS as the lower 8 bits of each word read from * the CIS, so to read the bytes of the CIS, read every other byte * (0,2,4,...). Passing that test, you need to enable the I/O address @@ -71,7 +51,7 @@ * within the PCI memory space. Write 0x41 to the COR register to * enable I/O mode and to select level triggered interrupts. To * confirm you actually succeeded, read the COR register back and make - * sure it actually got set to 0x41, incase you have an unexpected + * sure it actually got set to 0x41, in case you have an unexpected * card inserted. * * Following that, you can treat the second PCI I/O address space (the @@ -101,16 +81,6 @@ * that, I've hot-swapped a number of times during debugging and * driver development for various reasons (stuck WAIT# line after the * radio card's firmware locks up). - * - * Hope this is enough info for someone to add PLX9052 support to the - * wlan-ng card. In the case of the WL11000, the PCI ID's are - * 0x1639/0x0200, with matching subsystem ID's. Other PLX9052-based - * manufacturers other than Eumitcom (or on cards other than the - * WL11000) may have different PCI ID's. - * - * If anyone needs any more specific info, let me know. I haven't had - * time to implement support myself yet, and with the way things are - * going, might not have time for a while.. */ #define DRIVER_NAME "orinoco_plx" @@ -125,6 +95,7 @@ #include <pcmcia/cisreg.h> #include "orinoco.h" +#include "orinoco_pci.h" #define COR_OFFSET (0x3e0) /* COR attribute offset of Prism2 PC card */ #define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with interrupt in level trigger */ @@ -134,30 +105,20 @@ #define PLX_INTCSR 0x4c /* Interrupt Control & Status Register */ #define PLX_INTCSR_INTEN (1<<6) /* Interrupt Enable bit */ -static const u8 cis_magic[] = { - 0x01, 0x03, 0x00, 0x00, 0xff, 0x17, 0x04, 0x67 -}; - -/* Orinoco PLX specific data */ -struct orinoco_plx_card { - void __iomem *attr_mem; -}; - /* * Do a soft reset of the card using the Configuration Option Register */ static int orinoco_plx_cor_reset(struct orinoco_private *priv) { hermes_t *hw = &priv->hw; - struct orinoco_plx_card *card = priv->card; - u8 __iomem *attr_mem = card->attr_mem; + struct orinoco_pci_card *card = priv->card; unsigned long timeout; u16 reg; - writeb(COR_VALUE | COR_RESET, attr_mem + COR_OFFSET); + iowrite8(COR_VALUE | COR_RESET, card->attr_io + COR_OFFSET); mdelay(1); - writeb(COR_VALUE, attr_mem + COR_OFFSET); + iowrite8(COR_VALUE, card->attr_io + COR_OFFSET); mdelay(1); /* Just in case, wait more until the card is no longer busy */ @@ -168,7 +129,7 @@ static int orinoco_plx_cor_reset(struct orinoco_private *priv) reg = hermes_read_regn(hw, CMD); } - /* Did we timeout ? */ + /* Still busy? */ if (reg & HERMES_CMD_BUSY) { printk(KERN_ERR PFX "Busy timeout\n"); return -ETIMEDOUT; @@ -177,20 +138,55 @@ static int orinoco_plx_cor_reset(struct orinoco_private *priv) return 0; } +static int orinoco_plx_hw_init(struct orinoco_pci_card *card) +{ + int i; + u32 csr_reg; + static const u8 cis_magic[] = { + 0x01, 0x03, 0x00, 0x00, 0xff, 0x17, 0x04, 0x67 + }; + + printk(KERN_DEBUG PFX "CIS: "); + for (i = 0; i < 16; i++) { + printk("%02X:", ioread8(card->attr_io + (i << 1))); + } + printk("\n"); + + /* Verify whether a supported PC card is present */ + /* FIXME: we probably need to be smarted about this */ + for (i = 0; i < sizeof(cis_magic); i++) { + if (cis_magic[i] != ioread8(card->attr_io + (i << 1))) { + printk(KERN_ERR PFX "The CIS value of Prism2 PC " + "card is unexpected\n"); + return -ENODEV; + } + } + + /* bjoern: We need to tell the card to enable interrupts, in + case the serial eprom didn't do this already. See the + PLX9052 data book, p8-1 and 8-24 for reference. */ + csr_reg = ioread32(card->bridge_io + PLX_INTCSR); + if (!(csr_reg & PLX_INTCSR_INTEN)) { + csr_reg |= PLX_INTCSR_INTEN; + iowrite32(csr_reg, card->bridge_io + PLX_INTCSR); + csr_reg = ioread32(card->bridge_io + PLX_INTCSR); + if (!(csr_reg & PLX_INTCSR_INTEN)) { + printk(KERN_ERR PFX "Cannot enable interrupts\n"); + return -EIO; + } + } + + return 0; +} static int orinoco_plx_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { - int err = 0; - u8 __iomem *attr_mem = NULL; - u32 csr_reg, plx_addr; - struct orinoco_private *priv = NULL; - struct orinoco_plx_card *card; - unsigned long pccard_ioaddr = 0; - unsigned long pccard_iolen = 0; - struct net_device *dev = NULL; - void __iomem *mem; - int i; + int err; + struct orinoco_private *priv; + struct orinoco_pci_card *card; + struct net_device *dev; + void __iomem *hermes_io, *attr_io, *bridge_io; err = pci_enable_device(pdev); if (err) { @@ -199,30 +195,30 @@ static int orinoco_plx_init_one(struct pci_dev *pdev, } err = pci_request_regions(pdev, DRIVER_NAME); - if (err != 0) { + if (err) { printk(KERN_ERR PFX "Cannot obtain PCI resources\n"); goto fail_resources; } - /* Resource 1 is mapped to PLX-specific registers */ - plx_addr = pci_resource_start(pdev, 1); + bridge_io = pci_iomap(pdev, 1, 0); + if (!bridge_io) { + printk(KERN_ERR PFX "Cannot map bridge registers\n"); + err = -EIO; + goto fail_map_bridge; + } - /* Resource 2 is mapped to the PCMCIA attribute memory */ - attr_mem = ioremap(pci_resource_start(pdev, 2), - pci_resource_len(pdev, 2)); - if (!attr_mem) { - printk(KERN_ERR PFX "Cannot remap PCMCIA space\n"); + attr_io = pci_iomap(pdev, 2, 0); + if (!attr_io) { + printk(KERN_ERR PFX "Cannot map PCMCIA attributes\n"); + err = -EIO; goto fail_map_attr; } - /* Resource 3 is mapped to the PCMCIA I/O address space */ - pccard_ioaddr = pci_resource_start(pdev, 3); - pccard_iolen = pci_resource_len(pdev, 3); - - mem = pci_iomap(pdev, 3, 0); - if (!mem) { - err = -ENOMEM; - goto fail_map_io; + hermes_io = pci_iomap(pdev, 3, 0); + if (!hermes_io) { + printk(KERN_ERR PFX "Cannot map chipset registers\n"); + err = -EIO; + goto fail_map_hermes; } /* Allocate network device */ @@ -235,16 +231,12 @@ static int orinoco_plx_init_one(struct pci_dev *pdev, priv = netdev_priv(dev); card = priv->card; - card->attr_mem = attr_mem; - dev->base_addr = pccard_ioaddr; + card->bridge_io = bridge_io; + card->attr_io = attr_io; SET_MODULE_OWNER(dev); SET_NETDEV_DEV(dev, &pdev->dev); - hermes_struct_init(&priv->hw, mem, HERMES_16BIT_REGSPACING); - - printk(KERN_DEBUG PFX "Detected Orinoco/Prism2 PLX device " - "at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq, - pccard_ioaddr); + hermes_struct_init(&priv->hw, hermes_io, HERMES_16BIT_REGSPACING); err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name, dev); @@ -253,20 +245,11 @@ static int orinoco_plx_init_one(struct pci_dev *pdev, err = -EBUSY; goto fail_irq; } - dev->irq = pdev->irq; - /* bjoern: We need to tell the card to enable interrupts, in - case the serial eprom didn't do this already. See the - PLX9052 data book, p8-1 and 8-24 for reference. */ - csr_reg = inl(plx_addr + PLX_INTCSR); - if (!(csr_reg & PLX_INTCSR_INTEN)) { - csr_reg |= PLX_INTCSR_INTEN; - outl(csr_reg, plx_addr + PLX_INTCSR); - csr_reg = inl(plx_addr + PLX_INTCSR); - if (!(csr_reg & PLX_INTCSR_INTEN)) { - printk(KERN_ERR PFX "Cannot enable interrupts\n"); - goto fail; - } + err = orinoco_plx_hw_init(card); + if (err) { + printk(KERN_ERR PFX "Hardware initialization failed\n"); + goto fail; } err = orinoco_plx_cor_reset(priv); @@ -275,23 +258,6 @@ static int orinoco_plx_init_one(struct pci_dev *pdev, goto fail; } - printk(KERN_DEBUG PFX "CIS: "); - for (i = 0; i < 16; i++) { - printk("%02X:", readb(attr_mem + 2*i)); - } - printk("\n"); - - /* Verify whether a supported PC card is present */ - /* FIXME: we probably need to be smarted about this */ - for (i = 0; i < sizeof(cis_magic); i++) { - if (cis_magic[i] != readb(attr_mem +2*i)) { - printk(KERN_ERR PFX "The CIS value of Prism2 PC " - "card is unexpected\n"); - err = -EIO; - goto fail; - } - } - err = register_netdev(dev); if (err) { printk(KERN_ERR PFX "Cannot register network device\n"); @@ -299,6 +265,8 @@ static int orinoco_plx_init_one(struct pci_dev *pdev, } pci_set_drvdata(pdev, dev); + printk(KERN_DEBUG "%s: " DRIVER_NAME " at %s\n", dev->name, + pci_name(pdev)); return 0; @@ -310,12 +278,15 @@ static int orinoco_plx_init_one(struct pci_dev *pdev, free_orinocodev(dev); fail_alloc: - pci_iounmap(pdev, mem); + pci_iounmap(pdev, hermes_io); - fail_map_io: - iounmap(attr_mem); + fail_map_hermes: + pci_iounmap(pdev, attr_io); fail_map_attr: + pci_iounmap(pdev, bridge_io); + + fail_map_bridge: pci_release_regions(pdev); fail_resources: @@ -328,23 +299,20 @@ static void __devexit orinoco_plx_remove_one(struct pci_dev *pdev) { struct net_device *dev = pci_get_drvdata(pdev); struct orinoco_private *priv = netdev_priv(dev); - struct orinoco_plx_card *card = priv->card; - u8 __iomem *attr_mem = card->attr_mem; - - BUG_ON(! dev); + struct orinoco_pci_card *card = priv->card; unregister_netdev(dev); - free_irq(dev->irq, dev); + free_irq(pdev->irq, dev); pci_set_drvdata(pdev, NULL); free_orinocodev(dev); pci_iounmap(pdev, priv->hw.iobase); - iounmap(attr_mem); + pci_iounmap(pdev, card->attr_io); + pci_iounmap(pdev, card->bridge_io); pci_release_regions(pdev); pci_disable_device(pdev); } - -static struct pci_device_id orinoco_plx_pci_id_table[] = { +static struct pci_device_id orinoco_plx_id_table[] = { {0x111a, 0x1023, PCI_ANY_ID, PCI_ANY_ID,}, /* Siemens SpeedStream SS1023 */ {0x1385, 0x4100, PCI_ANY_ID, PCI_ANY_ID,}, /* Netgear MA301 */ {0x15e8, 0x0130, PCI_ANY_ID, PCI_ANY_ID,}, /* Correga - does this work? */ @@ -362,13 +330,15 @@ static struct pci_device_id orinoco_plx_pci_id_table[] = { {0,}, }; -MODULE_DEVICE_TABLE(pci, orinoco_plx_pci_id_table); +MODULE_DEVICE_TABLE(pci, orinoco_plx_id_table); static struct pci_driver orinoco_plx_driver = { .name = DRIVER_NAME, - .id_table = orinoco_plx_pci_id_table, + .id_table = orinoco_plx_id_table, .probe = orinoco_plx_init_one, .remove = __devexit_p(orinoco_plx_remove_one), + .suspend = orinoco_pci_suspend, + .resume = orinoco_pci_resume, }; static char version[] __initdata = DRIVER_NAME " " DRIVER_VERSION @@ -388,7 +358,6 @@ static int __init orinoco_plx_init(void) static void __exit orinoco_plx_exit(void) { pci_unregister_driver(&orinoco_plx_driver); - ssleep(1); } module_init(orinoco_plx_init); |