aboutsummaryrefslogtreecommitdiff
path: root/drivers/input/misc/winbond-cir.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/input/misc/winbond-cir.c')
-rw-r--r--drivers/input/misc/winbond-cir.c213
1 files changed, 104 insertions, 109 deletions
diff --git a/drivers/input/misc/winbond-cir.c b/drivers/input/misc/winbond-cir.c
index c8f5a9a3fa1..cbec3dfdd42 100644
--- a/drivers/input/misc/winbond-cir.c
+++ b/drivers/input/misc/winbond-cir.c
@@ -538,6 +538,7 @@ wbcir_reset_irdata(struct wbcir_data *data)
data->irdata_count = 0;
data->irdata_off = 0;
data->irdata_error = 0;
+ data->idle_count = 0;
}
/* Adds one bit of irdata */
@@ -1006,7 +1007,6 @@ wbcir_irq_handler(int irqno, void *cookie)
}
wbcir_reset_irdata(data);
- data->idle_count = 0;
}
out:
@@ -1018,7 +1018,7 @@ out:
/*****************************************************************************
*
- * SUSPEND/RESUME FUNCTIONS
+ * SETUP/INIT/SUSPEND/RESUME FUNCTIONS
*
*****************************************************************************/
@@ -1197,7 +1197,16 @@ finish:
}
/* Disable interrupts */
+ wbcir_select_bank(data, WBCIR_BANK_0);
outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER);
+
+ /*
+ * ACPI will set the HW disable bit for SP3 which means that the
+ * output signals are left in an undefined state which may cause
+ * spurious interrupts which we need to ignore until the hardware
+ * is reinitialized.
+ */
+ disable_irq(data->irq);
}
static int
@@ -1207,37 +1216,15 @@ wbcir_suspend(struct pnp_dev *device, pm_message_t state)
return 0;
}
-static int
-wbcir_resume(struct pnp_dev *device)
-{
- struct wbcir_data *data = pnp_get_drvdata(device);
-
- /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */
- wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
-
- /* Clear CEIR_EN */
- wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01);
-
- /* Enable interrupts */
- wbcir_reset_irdata(data);
- outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER);
-
- return 0;
-}
-
-
-
-/*****************************************************************************
- *
- * SETUP/INIT FUNCTIONS
- *
- *****************************************************************************/
-
static void
-wbcir_cfg_ceir(struct wbcir_data *data)
+wbcir_init_hw(struct wbcir_data *data)
{
u8 tmp;
+ /* Disable interrupts */
+ wbcir_select_bank(data, WBCIR_BANK_0);
+ outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER);
+
/* Set PROT_SEL, RX_INV, Clear CEIR_EN (needed for the led) */
tmp = protocol << 4;
if (invert)
@@ -1264,6 +1251,93 @@ wbcir_cfg_ceir(struct wbcir_data *data)
* set SP3_IRRX_SW to binary 01, helpfully not documented
*/
outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS);
+
+ /* Enable extended mode */
+ wbcir_select_bank(data, WBCIR_BANK_2);
+ outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1);
+
+ /*
+ * Configure baud generator, IR data will be sampled at
+ * a bitrate of: (24Mhz * prescaler) / (divisor * 16).
+ *
+ * The ECIR registers include a flag to change the
+ * 24Mhz clock freq to 48Mhz.
+ *
+ * It's not documented in the specs, but fifo levels
+ * other than 16 seems to be unsupported.
+ */
+
+ /* prescaler 1.0, tx/rx fifo lvl 16 */
+ outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2);
+
+ /* Set baud divisor to generate one byte per bit/cell */
+ switch (protocol) {
+ case IR_PROTOCOL_RC5:
+ outb(0xA7, data->sbase + WBCIR_REG_SP3_BGDL);
+ break;
+ case IR_PROTOCOL_RC6:
+ outb(0x53, data->sbase + WBCIR_REG_SP3_BGDL);
+ break;
+ case IR_PROTOCOL_NEC:
+ outb(0x69, data->sbase + WBCIR_REG_SP3_BGDL);
+ break;
+ }
+ outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH);
+
+ /* Set CEIR mode */
+ wbcir_select_bank(data, WBCIR_BANK_0);
+ outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR);
+ inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */
+ inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */
+
+ /* Disable RX demod, run-length encoding/decoding, set freq span */
+ wbcir_select_bank(data, WBCIR_BANK_7);
+ outb(0x10, data->sbase + WBCIR_REG_SP3_RCCFG);
+
+ /* Disable timer */
+ wbcir_select_bank(data, WBCIR_BANK_4);
+ outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1);
+
+ /* Enable MSR interrupt, Clear AUX_IRX */
+ wbcir_select_bank(data, WBCIR_BANK_5);
+ outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR2);
+
+ /* Disable CRC */
+ wbcir_select_bank(data, WBCIR_BANK_6);
+ outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3);
+
+ /* Set RX/TX (de)modulation freq, not really used */
+ wbcir_select_bank(data, WBCIR_BANK_7);
+ outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC);
+ outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC);
+
+ /* Set invert and pin direction */
+ if (invert)
+ outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4);
+ else
+ outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4);
+
+ /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */
+ wbcir_select_bank(data, WBCIR_BANK_0);
+ outb(0x97, data->sbase + WBCIR_REG_SP3_FCR);
+
+ /* Clear AUX status bits */
+ outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR);
+
+ /* Enable interrupts */
+ wbcir_reset_irdata(data);
+ outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER);
+}
+
+static int
+wbcir_resume(struct pnp_dev *device)
+{
+ struct wbcir_data *data = pnp_get_drvdata(device);
+
+ wbcir_init_hw(data);
+ enable_irq(data->irq);
+
+ return 0;
}
static int __devinit
@@ -1393,86 +1467,7 @@ wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id)
device_init_wakeup(&device->dev, 1);
- wbcir_cfg_ceir(data);
-
- /* Disable interrupts */
- wbcir_select_bank(data, WBCIR_BANK_0);
- outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER);
-
- /* Enable extended mode */
- wbcir_select_bank(data, WBCIR_BANK_2);
- outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1);
-
- /*
- * Configure baud generator, IR data will be sampled at
- * a bitrate of: (24Mhz * prescaler) / (divisor * 16).
- *
- * The ECIR registers include a flag to change the
- * 24Mhz clock freq to 48Mhz.
- *
- * It's not documented in the specs, but fifo levels
- * other than 16 seems to be unsupported.
- */
-
- /* prescaler 1.0, tx/rx fifo lvl 16 */
- outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2);
-
- /* Set baud divisor to generate one byte per bit/cell */
- switch (protocol) {
- case IR_PROTOCOL_RC5:
- outb(0xA7, data->sbase + WBCIR_REG_SP3_BGDL);
- break;
- case IR_PROTOCOL_RC6:
- outb(0x53, data->sbase + WBCIR_REG_SP3_BGDL);
- break;
- case IR_PROTOCOL_NEC:
- outb(0x69, data->sbase + WBCIR_REG_SP3_BGDL);
- break;
- }
- outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH);
-
- /* Set CEIR mode */
- wbcir_select_bank(data, WBCIR_BANK_0);
- outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR);
- inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */
- inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */
-
- /* Disable RX demod, run-length encoding/decoding, set freq span */
- wbcir_select_bank(data, WBCIR_BANK_7);
- outb(0x10, data->sbase + WBCIR_REG_SP3_RCCFG);
-
- /* Disable timer */
- wbcir_select_bank(data, WBCIR_BANK_4);
- outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1);
-
- /* Enable MSR interrupt, Clear AUX_IRX */
- wbcir_select_bank(data, WBCIR_BANK_5);
- outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR2);
-
- /* Disable CRC */
- wbcir_select_bank(data, WBCIR_BANK_6);
- outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3);
-
- /* Set RX/TX (de)modulation freq, not really used */
- wbcir_select_bank(data, WBCIR_BANK_7);
- outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC);
- outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC);
-
- /* Set invert and pin direction */
- if (invert)
- outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4);
- else
- outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4);
-
- /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */
- wbcir_select_bank(data, WBCIR_BANK_0);
- outb(0x97, data->sbase + WBCIR_REG_SP3_FCR);
-
- /* Clear AUX status bits */
- outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR);
-
- /* Enable interrupts */
- outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER);
+ wbcir_init_hw(data);
return 0;