/********************************************************************* * * Filename: irport.c * Version: 1.0 * Description: Half duplex serial port SIR driver for IrDA. * Status: Experimental. * Author: Dag Brattli * Created at: Sun Aug 3 13:49:59 1997 * Modified at: Fri Jan 28 20:22:38 2000 * Modified by: Dag Brattli * Sources: serial.c by Linus Torvalds * * Copyright (c) 1997, 1998, 1999-2000 Dag Brattli, All Rights Reserved. * Copyright (c) 2000-2003 Jean Tourrilhes, All Rights Reserved. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA * * This driver is ment to be a small half duplex serial driver to be * used for IR-chipsets that has a UART (16550) compatibility mode. * Eventually it will replace irtty, because of irtty has some * problems that is hard to get around when we don't have control * over the serial driver. This driver may also be used by FIR * drivers to handle SIR mode for them. * ********************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "irport.h" #define IO_EXTENT 8 /* * Currently you'll need to set these values using insmod like this: * insmod irport io=0x3e8 irq=11 */ static unsigned int io[] = { ~0, ~0, ~0, ~0 }; static unsigned int irq[] = { 0, 0, 0, 0 }; static unsigned int qos_mtt_bits = 0x03; static struct irport_cb *dev_self[] = { NULL, NULL, NULL, NULL}; static char *driver_name = "irport"; static inline void irport_write_wakeup(struct irport_cb *self); static inline int irport_write(int iobase, int fifo_size, __u8 *buf, int len); static inline void irport_receive(struct irport_cb *self); static int irport_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); static inline int irport_is_receiving(struct irport_cb *self); static int irport_set_dtr_rts(struct net_device *dev, int dtr, int rts); static int irport_raw_write(struct net_device *dev, __u8 *buf, int len); static struct net_device_stats *irport_net_get_stats(struct net_device *dev); static int irport_change_speed_complete(struct irda_task *task); static void irport_timeout(struct net_device *dev); static irqreturn_t irport_interrupt(int irq, void *dev_id); static int irport_hard_xmit(struct sk_buff *skb, struct net_device *dev); static void irport_change_speed(void *priv, __u32 speed); static int irport_net_open(struct net_device *dev); static int irport_net_close(struct net_device *dev); static struct irport_cb * irport_open(int i, unsigned int iobase, unsigned int irq) { struct net_device *dev; struct irport_cb *self; IRDA_DEBUG(1, "%s()\n", __FUNCTION__); /* Lock the port that we need */ if (!request_region(iobase, IO_EXTENT, driver_name)) { IRDA_DEBUG(0, "%s(), can't get iobase of 0x%03x\n", __FUNCTION__, iobase); goto err_out1; } /* * Allocate new instance of the driver */ dev = alloc_irdadev(sizeof(struct irport_cb)); if (!dev) { IRDA_ERROR("%s(), can't allocate memory for " "irda device!\n", __FUNCTION__); goto err_out2; } self = dev->priv; spin_lock_init(&self->lock); /* Need to store self somewhere */ dev_self[i] = self; self->priv = self; self->index = i; /* Initialize IO */ self->io.sir_base = iobase; self->io.sir_ext = IO_EXTENT; self->io.irq = irq; self->io.fifo_size = 16; /* 16550A and compatible */ /* Initialize QoS for this device */ irda_init_max_qos_capabilies(&self->qos); self->qos.baud_rate.bits = IR_9600|IR_19200|IR_38400|IR_57600| IR_115200; self->qos.min_turn_time.bits = qos_mtt_bits; irda_qos_bits_to_value(&self->qos); /* Bootstrap ZeroCopy Rx */ self->rx_buff.truesize = IRDA_SKB_MAX_MTU; self->rx_buff.skb = __dev_alloc_skb(self->rx_buff.truesize, GFP_KERNEL); if (self->rx_buff.skb == NULL) { IRDA_ERROR("%s(), can't allocate memory for " "receive buffer!\n", __FUNCTION__); goto err_out3; } skb_reserve(self->rx_buff.skb, 1); self->rx_buff.head = self->rx_buff.skb->data; /* No need to memset the buffer, unless you are really pedantic */ /* Finish setup the Rx buffer descriptor */ self->rx_buff.in_frame = FALSE; self->rx_buff.state = OUTSIDE_FRAME; self->rx_buff.data = self->rx_buff.head; /* Specify how much memory we want */ self->tx_buff.truesize = 4000; /* Allocate memory if needed */ if (self->tx_buff.truesize > 0) { self->tx_buff.head = kmalloc(self->tx_buff.truesize, GFP_KERNEL); if (self->tx_buff.head == NULL) { IRDA_ERROR("%s(), can't allocate memory for " "transmit buffer!\n", __FUNCTION__); goto err_out4; } memset(self->tx_buff.head, 0, self->tx_buff.truesize); } self->tx_buff.data = self->tx_buff.head; self->netdev = dev; /* Keep track of module usage */ SET_MODULE_OWNER(dev); /* May be overridden by piggyback drivers */ self->interrupt = irport_interrupt; self->change_speed = irport_change_speed; /* Override the network functions we need to use */ dev->hard_start_xmit = irport_hard_xmit; dev->tx_timeout = irport_timeout; dev->watchdog_timeo = HZ; /* Allow time enough for speed change */ dev->open = irport_net_open; dev->stop = irport_net_close; dev->get_stats = irport_net_get_stats; dev->do_ioctl = irport_net_ioctl; /* Make ifconfig display some details */ dev->base_addr = iobase; dev->irq = irq; if (register_netdev(dev)) { IRDA_ERROR("%s(), register_netdev() failed!\n", __FUNCTION__); goto err_out5; } IRDA_MESSAGE("IrDA: Registered device %s (irport io=0x%X irq=%d)\n", dev->name, iobase, irq); return self; err_out5: kfree(self->tx_buff.head); err_out4: kfree_skb(self->rx_buff.skb); err_out3: free_netdev(dev); dev_self[i] = NULL; err_out2: release_region(iobase, IO_EXTENT); err_out1: return NULL; } static int irport_close(struct irport_cb *self) { IRDA_ASSERT(self != NULL, return -1;); /* We are not using any dongle anymore! */ if (self->dongle) irda_device_dongle_cleanup(self->dongle); self->dongle = NULL; /* Remove netdevice */ unregister_netdev(self->netdev); /* Release the IO-port that this driver is using */ IRDA_DEBUG(0 , "%s(), Releasing Region %03x\n", __FUNCTION__, self->io.sir_base); release_region(self->io.sir_base, self->io.sir_ext); kfree(self->tx_buff.head); if (self->rx_buff.skb) kfree_skb(self->rx_buff.skb); self->rx_buff.skb = NULL; /* Remove ourselves */ dev_self[self->index] = NULL; free_netdev(self->netdev); return 0; } static void irport_stop(struct irport_cb *self) { int iobase; iobase = self->io.sir_base; /* We can't lock, we may be called from a FIR driver - Jean II */ /* We are not transmitting any more */ self->transmitting = 0; /* Reset UART */ outb(0, iobase+UART_MCR); /* Turn off interrupts */ outb(0, iobase+UART_IER); } static void irport_start(struct irport_cb *self) { int iobase; iobase = self->io.sir_base; irport_stop(self); /* We can't lock, we may be called from a FIR driver - Jean II */ /* Initialize UART */ outb(UART_LCR_WLEN8, iobase+UART_LCR); /* Reset DLAB */ outb((UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2), iobase+UART_MCR); /* Turn on interrups */ outb(UART_IER_RLSI | UART_IER_RDI |UART_IER_THRI, iobase+UART_IER); } /* * Function irport_get_fcr (speed) * * Compute value of fcr * */ static inline unsigned int irport_get_fcr(__u32 speed) { unsigned int fcr; /* FIFO control reg */ /* Enable fifos */ fcr = UART_FCR_ENABLE_FIFO; /* * Use trigger level 1 to avoid 3 ms. timeout delay at 9600 bps, and * almost 1,7 ms at 19200 bps. At speeds above that we can just forget * about this timeout since it will always be fast enough. */ if (speed < 38400) fcr |= UART_FCR_TRIGGER_1; else //fcr |= UART_FCR_TRIGGER_14; fcr |= UART_FCR_TRIGGER_8; return(fcr); } /* * Function irport_change_speed (self, speed) * * Set speed of IrDA port to specified baudrate * * This function should be called with irq off and spin-lock. */ static void irport_change_speed(void *priv, __u32 speed) { struct irport_cb *self = (struct irport_cb *) priv; int iobase; unsigned int fcr; /* FIFO control reg */ unsigned int lcr; /* Line control reg */ int divisor; IRDA_ASSERT(self != NULL, return;); IRDA_ASSERT(speed != 0, return;); IRDA_DEBUG(1, "%s(), Setting speed to: %d - iobase=%#x\n", __FUNCTION__, speed, self->io.sir_base); /* We can't lock, we may be called from a FIR driver - Jean II */ iobase = self->io.sir_base; /* Update accounting for new speed */ self->io.speed = speed; /* Turn off interrupts */ outb(0, iobase+UART_IER); divisor = SPEED_MAX/speed; /* Get proper fifo configuration */ fcr = irport_get_fcr(speed); /* IrDA ports use 8N1 */ lcr = UART_LCR_WLEN8; outb(UART_LCR_DLAB | lcr, iobase+UART_LCR); /* Set DLAB */ outb(divisor & 0xff, iobase+UART_DLL); /* Set speed */ outb(divisor >> 8, iobase+UART_DLM); outb(lcr, iobase+UART_LCR); /* Set 8N1 */ outb(fcr, iobase+UART_FCR); /* Enable FIFO's */ /* Turn on interrups */ /* This will generate a fatal interrupt storm. * People calling us will do that properly - Jean II */ //outb(/*UART_IER_RLSI|*/UART_IER_RDI/*|UART_IER_THRI*/, iobase+UART_IER); } /* * Function __irport_change_speed (instance, state, param) * * State machine for changing speed of the device. We do it this way since * we cannot use schedule_timeout() when we are in interrupt context * */ static int __irport_change_speed(struct irda_task *task) { struct irport_cb *self; __u32 speed = (__u32) task->param; unsigned long flags = 0; int wasunlocked = 0; int ret = 0; IRDA_DEBUG(2, "%s(), <%ld>\n", __FUNCTION__, jiffies); self = (struct irport_cb *) task->instance; IRDA_ASSERT(self != NULL, return -1;); /* Locking notes : this function may be called from irq context with * spinlock, via irport_write_wakeup(), or from non-interrupt without * spinlock (from the task timer). Yuck ! * This is ugly, and unsafe is the spinlock is not already acquired. * This will be fixed when irda-task get rewritten. * Jean II */ if (!spin_is_locked(&self->lock)) { spin_lock_irqsave(&self->lock, flags); wasunlocked = 1; } switch (task->state) { case IRDA_TASK_INIT: case IRDA_TASK_WAIT: /* Are we ready to change speed yet? */ if (self->tx_buff.len > 0) { task->state = IRDA_TASK_WAIT; /* Try again later */ ret = msecs_to_jiffies(20); break; } if (self->dongle) irda_task_next_state(task, IRDA_TASK_CHILD_INIT); else irda_task_next_state(task, IRDA_TASK_CHILD_DONE); break; case IRDA_TASK_CHILD_INIT: /* Go to default speed */ self->change_speed(self->priv, 9600); /* Change speed of dongle */ if (irda_task_execute(self->dongle, self->dongle->issue->change_speed, NULL, task, (void *) speed)) { /* Dongle need more time to change its speed */ irda_task_next_state(task, IRDA_TASK_CHILD_WAIT); /* Give dongle 1 sec to finish */ ret = msecs_to_jiffies(1000); } else /* Child finished immediately */ irda_task_next_state(task, IRDA_TASK_CHILD_DONE); break; case IRDA_TASK_CHILD_WAIT: IRDA_WARNING("%s(), changing speed of dongle timed out!\n", __FUNCTION__); ret = -1; break; case IRDA_TASK_CHILD_DONE: /* Finally we are ready to change the speed */ self->change_speed(self->priv, speed); irda_task_next_state(task, IRDA_TASK_DONE); break; default: IRDA_ERROR("%s(), unknown state %d\n", __FUNCTION__, task->state); irda_task_next_state(task, IRDA_TASK_DONE); ret = -1; break; } /* Put stuff in the state we found them - Jean II */ if(wasunlocked) { spin_unlock_irqrestore(&self->lock, flags); } return ret; } /* * Function irport_change_speed_complete (task) * * Called when the change speed operation completes * */ static int irport_change_speed_complete(struct irda_task *task) { struct irport_cb *self; IRDA_DEBUG(1, "%s()\n", __FUNCTION__); self = (struct irport_cb *) task->instance; IRDA_ASSERT(self != NULL, return -1;); IRDA_ASSERT(self->netdev != NULL, return -1;); /* Finished changing speed, so we are not busy any longer */ /* Signal network layer so it can try to send the frame */ netif_wake_queue(self->netdev); return 0; } /* * Function irport_timeout (struct net_device *dev) * * The networking layer thinks we timed out. * */ static void irport_timeout(struct net_device *dev) { struct irport_cb *self; int iobase; int iir, lsr; unsigned long flags; self = (struct irport_cb *) dev->priv; IRDA_ASSERT(self != NULL, return;); iobase = self->io.sir_base; IRDA_WARNING("%s: transmit timed out, jiffies = %ld, trans_start = %ld\n", dev->name, jiffies, dev->trans_start); spin_lock_irqsave(&self->lock, flags); /* Debug what's happening... */ /* Get interrupt status */ lsr = inb(iobase+UART_LSR); /* Read interrupt register */ iir = inb(iobase+UART_IIR); IRDA_DEBUG(0, "%s(), iir=%02x, lsr=%02x, iobase=%#x\n", __FUNCTION__, iir, lsr, iobase); IRDA_DEBUG(0, "%s(), transmitting=%d, remain=%d, done=%d\n", __FUNCTION__, self->transmitting, self->tx_buff.len, self->tx_buff.data - self->tx_buff.head); /* Now, restart the port */ irport_start(self); self->change_speed(self->priv, self->io.speed); /* This will re-enable irqs */ outb(/*UART_IER_RLSI|*/UART_IER_RDI/*|UART_IER_THRI*/, iobase+UART_IER); dev->trans_start = jiffies; spin_unlock_irqrestore(&self->lock, flags); netif_wake_queue(dev); } /* * Function irport_wait_hw_transmitter_finish () * * Wait for the real end of HW transmission * * The UART is a strict FIFO, and we get called only when we have finished * pushing data to the FIFO, so the maximum amount of time we must wait * is only for the FIFO to drain out. * * We use a simple calibrated loop. We may need to adjust the loop * delay (udelay) to balance I/O traffic and latency. And we also need to * adjust the maximum timeout. * It would probably be better to wait for the proper interrupt, * but it doesn't seem to be available. * * We can't use jiffies or kernel timers because : * 1) We are called from the interrupt handler, which disable softirqs, * so jiffies won't be increased * 2) Jiffies granularity is usually very coarse (10ms), and we don't * want to wait that long to detect stuck hardware. * Jean II */ static void irport_wait_hw_transmitter_finish(struct irport_cb *self) { int iobase; int count = 1000; /* 1 ms */ iobase = self->io.sir_base; /* Calibrated busy loop */ while((count-- > 0) && !(inb(iobase+UART_LSR) & UART_LSR_TEMT)) udelay(1); if(count == 0) IRDA_DEBUG(0, "%s(): stuck transmitter\n", __FUNCTION__); } /* * Function irport_hard_start_xmit (struct sk_buff *skb, struct net_device *dev) * * Transmits the current frame until FIFO is full, then * waits until the next transmitt interrupt, and continues until the * frame is transmitted. */ static int irport_hard_xmit(struct sk_buff *skb, struct net_device *dev) { struct irport_cb *self; unsigned long flags; int iobase; s32 speed; IRDA_DEBUG(1, "%s()\n", __FUNCTION__); IRDA_ASSERT(dev != NULL, return 0;); self = (struct irport_cb *) dev->priv; IRDA_ASSERT(self != NULL, return 0;); iobase = self->io.sir_base; netif_stop_queue(dev); /* Make sure tests & speed change are atomic */ spin_lock_irqsave(&self->lock, flags); /* Check if we need to change the speed */ speed = irda_get_next_speed(skb); if ((speed != self->io.speed) && (speed != -1)) { /* Check for empty frame */ if (!skb->len) { /* * We send frames one by one in SIR mode (no * pipelining), so at this point, if we were sending * a previous frame, we just received the interrupt * telling us it is finished (UART_IIR_THRI). * Therefore, waiting for the transmitter to really * finish draining the fifo won't take too long. * And the interrupt handler is not expected to run. * - Jean II */ irport_wait_hw_transmitter_finish(self); /* Better go there already locked - Jean II */ irda_task_execute(self, __irport_change_speed, irport_change_speed_complete, NULL, (void *) speed); dev->trans_start = jiffies; spin_unlock_irqrestore(&self->lock, flags); dev_kfree_skb(skb); return 0; } else self->new_speed = speed; } /* Init tx buffer */ self->tx_buff.data = self->tx_buff.head; /* Copy skb to tx_buff while wrapping, stuffing and making CRC */ self->tx_buff.len = async_wrap_skb(skb, self->tx_buff.data, self->tx_buff.truesize); self->stats.tx_bytes += self->tx_buff.len; /* We are transmitting */ self->transmitting = 1; /* Turn on transmit finished interrupt. Will fire immediately! */ outb(UART_IER_THRI, iobase+UART_IER); dev->trans_start = jiffies; spin_unlock_irqrestore(&self->lock, flags); dev_kfree_skb(skb); return 0; } /* * Function irport_write (driver) * * Fill Tx FIFO with transmit data * * Called only from irport_write_wakeup() */ static inline int irport_write(int iobase, int fifo_size, __u8 *buf, int len) { int actual = 0; /* Fill FIFO with current frame */ while ((actual < fifo_size) && (actual < len)) { /* Transmit next byte */ outb(buf[actual], iobase+UART_TX); actual++; } return actual; } /* * Function irport_write_wakeup (tty) * * Called by the driver when there's room for more data. If we have * more packets to send, we send them here. * * Called only from irport_interrupt() * Make sure this function is *not* called while we are receiving, * otherwise we will reset fifo and loose data :-( */ static inline void irport_write_wakeup(struct irport_cb *self) { int actual = 0; int iobase; unsigned int fcr; IRDA_ASSERT(self != NULL, return;); IRDA_DEBUG(4, "%s()\n", __FUNCTION__); iobase = self->io.sir_base; /* Finished with frame? */ if (self->tx_buff.len > 0) { /* Write data left in transmit buffer */ actual = irport_write(iobase, self->io.fifo_size, self->tx_buff.data, self->tx_buff.len); self->tx_buff.data += actual; self->tx_buff.len -= actual; } else { /* * Now serial buffer is almost free & we can start * transmission of another packet. But first we must check * if we need to change the speed of the hardware */ if (self->new_speed) { irport_wait_hw_transmitter_finish(self); irda_task_execute(self, __irport_change_speed, irport_change_speed_complete, NULL, (void *) self->new_speed); self->new_speed = 0; } else { /* Tell network layer that we want more frames */ netif_wake_queue(self->netdev); } self->stats.tx_packets++; /* * Reset Rx FIFO to make sure that all reflected transmit data * is discarded. This is needed for half duplex operation */ fcr = irport_get_fcr(self->io.speed); fcr |= UART_FCR_CLEAR_RCVR; outb(fcr, iobase+UART_FCR); /* Finished transmitting */ self->transmitting = 0; /* Turn on receive interrupts */ outb(UART_IER_RDI, iobase+UART_IER); IRDA_DEBUG(1, "%s() : finished Tx\n", __FUNCTION__); } } /* * Function irport_receive (self) * * Receive one frame from the infrared port * * Called only from irport_interrupt() */ static inline void irport_receive(struct irport_cb *self) { int boguscount = 0; int iobase; IRDA_ASSERT(self != NULL, return;); iobase = self->io.sir_base; /* * Receive all characters in Rx FIFO, unwrap and unstuff them. * async_unwrap_char will deliver all found frames */ do { async_unwrap_char(self->netdev, &self->stats, &self->rx_buff, inb(iobase+UART_RX)); /* Make sure we don't stay here too long */ if (boguscount++ > 32) { IRDA_DEBUG(2,"%s(), breaking!\n", __FUNCTION__); break; } } while (inb(iobase+UART_LSR) & UART_LSR_DR); } /* * Function irport_interrupt (irq, dev_id) * * Interrupt handler */ static irqreturn_t irport_interrupt(int irq, void *dev_id) { struct net_device *dev = dev_id; struct irport_cb *self; int boguscount = 0; int iobase; int iir, lsr; int handled = 0; self = dev->priv; spin_lock(&self->lock); iobase = self->io.sir_base; /* Cut'n'paste interrupt routine from serial.c * This version try to minimise latency and I/O operations. * Simplified and modified to enforce half duplex operation. * - Jean II */ /* Check status even is iir reg is cleared, more robust and * eliminate a read on the I/O bus - Jean II */ do { /* Get interrupt status ; Clear interrupt */ lsr = inb(iobase+UART_LSR); /* Are we receiving or transmitting ? */ if(!self->transmitting) { /* Received something ? */ if (lsr & UART_LSR_DR) irport_receive(self); } else { /* Room in Tx fifo ? */ if (lsr & (UART_LSR_THRE | UART_LSR_TEMT)) irport_write_wakeup(self); } /* A bit hackish, but working as expected... Jean II */ if(lsr & (UART_LSR_THRE | UART_LSR_TEMT | UART_LSR_DR)) handled = 1; /* Make sure we don't stay here to long */ if (boguscount++ > 10) { IRDA_WARNING("%s() irq handler looping : lsr=%02x\n", __FUNCTION__, lsr); break; } /* Read interrupt register */ iir = inb(iobase+UART_IIR); /* Enable this debug only when no other options and at low * bit rates, otherwise it may cause Rx overruns (lsr=63). * - Jean II */ IRDA_DEBUG(6, "%s(), iir=%02x, lsr=%02x, iobase=%#x\n", __FUNCTION__, iir, lsr, iobase); /* As long as interrupt pending... */ } while ((iir & UART_IIR_NO_INT) == 0); spin_unlock(&self->lock); return IRQ_RETVAL(handled); } /* * Function irport_net_open (dev) * * Network device is taken up. Usually this is done by "ifconfig irda0 up" * */ static int irport_net_open(struct net_device *dev) { struct irport_cb *self; int iobase; char hwname[16]; unsigned long flags; IRDA_DEBUG(2, "%s()\n", __FUNCTION__); IRDA_ASSERT(dev != NULL, return -1;); self = (struct irport_cb *) dev->priv; iobase = self->io.sir_base; if (request_irq(self->io.irq, self->interrupt, 0, dev->name, (void *) dev)) { IRDA_DEBUG(0, "%s(), unable to allocate irq=%d\n", __FUNCTION__, self->io.irq); return -EAGAIN; } spin_lock_irqsave(&self->lock, flags); /* Init uart */ irport_start(self); /* Set 9600 bauds per default, including at the dongle */ irda_task_execute(self, __irport_change_speed, irport_change_speed_complete, NULL, (void *) 9600); spin_unlock_irqrestore(&self->lock, flags); /* Give self a hardware name */ sprintf(hwname, "SIR @ 0x%03x", self->io.sir_base); /* * Open new IrLAP layer instance, now that everything should be * initialized properly */ self->irlap = irlap_open(dev, &self->qos, hwname); /* Ready to play! */ netif_start_queue(dev); return 0; } /* * Function irport_net_close (self) * * Network device is taken down. Usually this is done by * "ifconfig irda0 down" */ static int irport_net_close(struct net_device *dev) { struct irport_cb *self; int iobase; unsigned long flags; IRDA_DEBUG(4, "%s()\n", __FUNCTION__); IRDA_ASSERT(dev != NULL, return -1;); self = (struct irport_cb *) dev->priv; IRDA_ASSERT(self != NULL, return -1;); iobase = self->io.sir_base; /* Stop device */ netif_stop_queue(dev); /* Stop and remove instance of IrLAP */ if (self->irlap) irlap_close(self->irlap); self->irlap = NULL; spin_lock_irqsave(&self->lock, flags); irport_stop(self); spin_unlock_irqrestore(&self->lock, flags); free_irq(self->io.irq, dev); return 0; } /* * Function irport_is_receiving (self) * * Returns true is we are currently receiving data * */ static inline int irport_is_receiving(struct irport_cb *self) { return (self->rx_buff.state != OUTSIDE_FRAME); } /* * Function irport_set_dtr_rts (tty, dtr, rts) * * This function can be used by dongles etc. to set or reset the status * of the dtr and rts lines */ static int irport_set_dtr_rts(struct net_device *dev, int dtr, int rts) { struct irport_cb *self = dev->priv; int iobase; IRDA_ASSERT(self != NULL, return -1;); iobase = self->io.sir_base; if (dtr) dtr = UART_MCR_DTR; if (rts) rts = UART_MCR_RTS; outb(dtr|rts|UART_MCR_OUT2, iobase+UART_MCR); return 0; } static int irport_raw_write(struct net_device *dev, __u8 *buf, int len) { struct irport_cb *self = (struct irport_cb *) dev->priv; int actual = 0; int iobase; IRDA_ASSERT(self != NULL, return -1;); iobase = self->io.sir_base; /* Tx FIFO should be empty! */ if (!(inb(iobase+UART_LSR) & UART_LSR_THRE)) { IRDA_DEBUG( 0, "%s(), failed, fifo not empty!\n", __FUNCTION__); return -1; } /* Fill FIFO with current frame */ while (actual < len) { /* Transmit next byte */ outb(buf[actual], iobase+UART_TX); actual++; } return actual; } /* * Function irport_net_ioctl (dev, rq, cmd) * * Process IOCTL commands for this device * */ static int irport_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) { struct if_irda_req *irq = (struct if_irda_req *) rq; struct irport_cb *self; dongle_t *dongle; unsigned long flags; int ret = 0; IRDA_ASSERT(dev != NULL, return -1;); self = dev->priv; IRDA_ASSERT(self != NULL, return -1;); IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__, dev->name, cmd); switch (cmd) { case SIOCSBANDWIDTH: /* Set bandwidth */ if (!capable(CAP_NET_ADMIN)) ret = -EPERM; else irda_task_execute(self, __irport_change_speed, NULL, NULL, (void *) irq->ifr_baudrate); break; case SIOCSDONGLE: /* Set dongle */ if (!capable(CAP_NET_ADMIN)) { ret = -EPERM; break; } /* Locking : * irda_device_dongle_init() can't be locked. * irda_task_execute() doesn't need to be locked. * Jean II */ /* Initialize dongle */ dongle = irda_device_dongle_init(dev, irq->ifr_dongle); if (!dongle) break; dongle->set_mode = NULL; dongle->read = NULL; dongle->write = irport_raw_write; dongle->set_dtr_rts = irport_set_dtr_rts; /* Now initialize the dongle! */ dongle->issue->open(dongle, &self->qos); /* Reset dongle */ irda_task_execute(dongle, dongle->issue->reset, NULL, NULL, NULL); /* Make dongle available to driver only now to avoid * race conditions - Jean II */ self->dongle = dongle; break; case SIOCSMEDIABUSY: /* Set media busy */ if (!capable(CAP_NET_ADMIN)) { ret = -EPERM; break; } irda_device_set_media_busy(self->netdev, TRUE); break; case SIOCGRECEIVING: /* Check if we are receiving right now */ irq->ifr_receiving = irport_is_receiving(self); break; case SIOCSDTRRTS: if (!capable(CAP_NET_ADMIN)) { ret = -EPERM; break; } /* No real need to lock... */ spin_lock_irqsave(&self->lock, flags); irport_set_dtr_rts(dev, irq->ifr_dtr, irq->ifr_rts); spin_unlock_irqrestore(&self->lock, flags); break; default: ret = -EOPNOTSUPP; } return ret; } static struct net_device_stats *irport_net_get_stats(struct net_device *dev) { struct irport_cb *self = (struct irport_cb *) dev->priv; return &self->stats; } static int __init irport_init(void) { int i; for (i=0; (io[i] < 2000) && (i < ARRAY_SIZE(dev_self)); i++) { if (irport_open(i, io[i], irq[i]) != NULL) return 0; } /* * Maybe something failed, but we can still be usable for FIR drivers */ return 0; } /* * Function irport_cleanup () * * Close all configured ports * */ static void __exit irport_cleanup(void) { int i; IRDA_DEBUG( 4, "%s()\n", __FUNCTION__); for (i=0; i < ARRAY_SIZE(dev_self); i++) { if (dev_self[i]) irport_close(dev_self[i]); } } module_param_array(io, int, NULL, 0); MODULE_PARM_DESC(io, "Base I/O addresses"); module_param_array(irq, int, NULL, 0); MODULE_PARM_DESC(irq, "IRQ lines"); MODULE_AUTHOR("Dag Brattli "); MODULE_DESCRIPTION("Half duplex serial driver for IrDA SIR mode"); MODULE_LICENSE("GPL"); module_init(irport_init); module_exit(irport_cleanup);