aboutsummaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2013-02-07board: samsung: Update MAC address for Arndale board through GUID2013.02.2Tushar Behera
There are a couple of GUID (Global Unique Identifier) registers within EXYNOS5250 SoC. The values of these GUID registers are set as board MAC address. Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
2013-02-04arndale5250: Boot in Hyp mode and enable architected timersChristoffer Dall
First, to boot in Hyp mode we need to change to non-secure mode, which involves configuring the frequency of the arch. timers and setting all interrupts on the gic to group 1 (this code was inspired by the boot wrapper code). Second, signal the secondary CPU while still in secure mode and have the secondary CPU run the SPL. The SPL checks the hardware cpu id, and if it's a secondary CPU, it will initialize non-secure mode inside the SPL, enter Hyp mode, and finally enter a new SMP pen with the same poking stick interface as the regular kernel uses. Third, on CPU0 we wait until u-boot is fully up to actually enter the non-secure mode on CPU0, and stay in non-secure svc mode right up until we actually load the kernel, where the last thing we do is enter Hyp mode. Let it roll... Signed-off-by: Jeremy C. Andrus <jeremya@cs.columbia.edu> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2012-12-06ARM: add optional call to ft_board_setupRob Herring
Allow board specific FDT fixups on ARM using the ft_board_setup function. This is enabled using CONFIG_OF_BOARD_SETUP define. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-12-06ARM: highbank: fix get_tbclk value to timer rateRob Herring
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-12-06ARM: highbank: set timer prescaler to 256Rob Herring
The 150MHz clock rate gives u-boot time functions problems and there's no benefit to a fast clock, so lower the rate. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-12-06DRIVERS: USB: Initialize HSIC PHYs and enable network supportInderpal Singh
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo controller, connected to HSIC Phy of USB host controller via USB3503 hub. This patch initializes the HSIC PHYs, performs reset sequence for USB3503 hub and enables the relevant config options for network to work. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
2012-12-06arm: exynos: fix issue in clock and pinmuxGirish K S
clock: the mmc get clock api return the clock value without dividing the sclk by value of clk_sel register. The divider value calculated in the dw_mmc driver for clk_div is wrong. This patch adds the divider to fix the issue. pinmux: The initialization of the sd_cdn pin was ignored, This patch adds the selection and initialization of the early pin state. Signed-off-by: Girish K S <iks.giri@samsung.com>
2012-12-06arm: exynos: additional changes to arndaleGirish K S
added more changes to the configuration and clock of mmc Signed-off-by: Girish K S <girish@avatar.(none)>
2012-12-06EXYNOS: mmc: support DesignWare Controller for Samsung-SoCJaehoon Chung
Support DesignWare MMC Controller for Samsung Specific. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Rajeshawari Shinde <rajeshwari.s@samsung.com>
2012-12-06EXYNOS: clock: add the get_mmc_clk functionJaehoon Chung
To get more exactly sclk value, used the get_mmc_clk. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2012-12-06EXYNOS: additional Exynos4 SoC series supportJeong-Hyeon Kim
- Fixed MPLL register address It's different between Exynos4210 and Exynos4412. - Added pinmux functions for Exynos4 - Added extended gpios for Exynos4412 Exynos4412 has more gpios than Exynos4210. Signed-off-by: Jeong-Hyeon Kim <jhkim@insignal.co.kr>
2012-12-06EXYNOS: add XXTI for clock sourceJeong-Hyeon Kim
Exynos SoC series are various and cover the different range of MCLK. Several clock setting is based on MPLL, but it's to easy change depend on board configuration. So, common setting of clock need for cover the various type of memory. System clock (XXTI) is one of solution for it. Signed-off-by: Jeong-Hyeon Kim <jhkim@insignal.co.kr>
2012-12-06gpio:fix: Proper handling of GPIO subsystem parts at Samsung devicesŁukasz Majewski
Now proper GPIO parts numbering is handled at Samsung devices. This fix is necessary for code using GPIO located at other banks than first. Test HW: - Exynos4210 - Trats - S5PC110 - goni Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-12-06Revert "armv7: adapt omap3 to the new cache maintenance framework"Ricardo Salveti de Araujo
This reverts commit 45bf05854bc94ed8bae9e9114292895b990327ea. Conflicts: arch/arm/cpu/armv7/omap3/board.c arch/arm/cpu/armv7/omap3/lowlevel_init.S arch/arm/include/asm/arch-omap3/sys_proto.h Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
2012-12-06SAUCE: HACK: move omap spl base addressJohn Rigby
Move NON_SECURE_SRAM_START from 0x40304000 to 0x40303000 and move u-boot-spl load address from 0x40304350 to 0x40303080. This allows it to stay under 0x4030c000 which is what the TRM says it must do. SRAM actually starts at 0x40300000 on GP devices but was set to 0x40304000 to be the same as Secure devices so this breaks that. Signed-off-by: John Rigby <john.rigby@linaro.org>
2012-12-06OMAP3: Beagle: set mac addr from dieidJohn Rigby
TODO: share dieid<-->mac addr code between OMAP3 and OMAP4 Signed-off-by: John Rigby <john.rigby@linaro.org>
2012-12-06OMAP4 Panda: Generate a unique usbethaddrJohn Rigby
The panda board has a usb nic but the nic has no rom. Use the die-id to generate a unique address. This is derived from an RFC kernel patch by Andy Green that does the same thing: https://patchwork.kernel.org/patch/660541/ [RFC PATCH 1/2] OMAP2+: add cpu id register to MAC address helper Signed-off-by: John Rigby <john.rigby@linaro.org>
2012-12-06OMAP4: Panda: Add usb peripheral bootJohn Rigby
Stripped down fastboot protocol for now but could be just about anything. Will revisit once a fastboot or dfu implementation hits upstream. Signed-off-by: John Rigby <john.rigby@linaro.org> Conflicts: arch/arm/cpu/armv7/omap-common/Makefile arch/arm/include/asm/omap_common.h common/spl/spl.c include/configs/omap4_common.h spl/Makefile
2012-12-06OMAP4: avoid null pointer access in save_boot_paramsJohn Rigby
When booting via spl the parameter layout is apparently different and this leads to following bad pointers. For now just work around the issue by checking pointers before following them. Signed-off-by: John Rigby <john.rigby@linaro.org>
2012-11-04include/linux/byteorder: import latest endian definitions from linuxKim Phillips
u-boot's byteorder headers did not contain endianness attributions for use with sparse, causing a lot of false positives. Import the kernel's latest definitions, and enable them by including compiler.h and types.h. They come with 'const' added for some swab functions, so fix those up, too: include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default] Also, note: u-boot's historic __BYTE_ORDER definition has been preserved (for the time being at least). We also remove ad-hoc barrier() definitions, since we're including compiler.h in files that hadn't in the past: macb.c:54:0: warning: "barrier" redefined [enabled by default] In addition, including compiler.h in byteorder changes the 'noinline' definition to expand to __attribute__((noinline)). This fixes arch/powerpc/lib/bootm.c: bootm.c:329:16: error: attribute '__attribute__': unknown attribute bootm.c:329:16: error: expected ')' before '__attribute__' bootm.c:329:25: error: expected identifier or '(' before ')' token powerpc sparse builds yield: include/common.h:356:22: error: marked inline, but without a definition the unknown-reason inlining without a definition is considered obsolete given it was part of the 2002 initial commit, and no arm version was 'fixed.' also fixed: ydirectenv.h:60:0: warning: "inline" redefined [enabled by default] and: Configuring for devconcenter - Board: intip, Options: DEVCONCENTER make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1 make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2 powerpc-fsl-linux-size: './u-boot': No such file 4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration': include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available 4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here and: In file included from crc32.c:50:0: crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration] crc32table.h:4:1: error: initializer element is not constant crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]') Signed-off-by: Kim Phillips <kim.phillips@freescale.com> [trini: Remove '#endif' in include/common.h around setenv portion] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-26ARM: fix u-boot.lds for -ffunction-sections/-fdata-sectionsStephen Warren
When -ffunction-sections or -fdata-section are used, symbols are placed into sections such as .data.eserial1_device and .bss.serial_current. Update the linker script to explicitly include these. Without this change (at least with my gcc-4.5.3 built using crosstool-ng), I see that the sections do end up being included, but __bss_end__ gets set to the same value as __bss_start. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2012-10-26arm: ks8695: use defined constants for UARTYann Vernier
CONFIG_BAUDRATE and KS8695_UART_LINEC_WLEN8 used for UART registers
2012-10-26arm720: Remove CONFIG_ARM7_REVDMarek Vasut
This is a dead code, remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm720: Further clean up the arm720t directoryMarek Vasut
Clean up away old macros and such, so the file doesn't start piling up cruft. Signed-off-by: Marek Vasut <marex@denx.de> clean
2012-10-26stdio: Remove the CLPS7111 serial driverMarek Vasut
This driver is no longer used, remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for NETARMMarek Vasut
This stuff has been rotting in the tree for a while now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for s3c4510Marek Vasut
This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for lpc2292Marek Vasut
This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26Merge remote-tracking branch 'u-boot-atmel/master'Albert ARIBAUD
2012-10-26Merge remote-tracking branch 'u-boot-ti/master'Albert ARIBAUD
2012-10-25am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbersPeter Korsgaard
So other parts can be added. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: support board specific ddr settingsPeter Korsgaard
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code, so other boards can use different types/timings. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make apply with rtc32k_enable() in the file] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx: move generic parts of pinmux handling out from board/ti/am335xPeter Korsgaard
So they are available for other boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx/board: use cpu_mmc_init() for default mmc initializationPeter Korsgaard
So platforms can override it with board_mmc_init() if needed. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: move ti i2c baseboard header handling to board/ti/am335x/Peter Korsgaard
The i2c header is specific to ti(-derived) boards, and not generic for all am335x boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make re-apply with rtc32k_enable() applied] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx/board.c: make wdtimer/uart_base staticPeter Korsgaard
Only used here (and uart_base only for SPL). Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: Add SPI SPL as an optionTom Rini
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE define. Finally, enable the options on the am335x_evm. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25VIDEO: add macro to set LCD size for DSS driverStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-10-25am335x: Enable RTC 32K OSC clockVaibhav Hiremath
In order to support low power state, you must source kernel system timers to persistent clock, available across suspend/resume. In case of AM335x device, the only source we have is, RTC32K, available in wakeup/always-on domain. Having said that, during validation it has been observed that, RTC clock need couple of seconds delay to stabilize the RTC OSC clock; and such a huge delay is not acceptable in kernel especially during early init and also it will impact quick/fast boot use-cases. So, RTC32k OSC enable dependency has been shifted to SPL/first-bootloader. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-23am33xx: Enable DDR3 for DDR3 version of beagleboneJoel A Fernandes
DDR3 support is tested and working with beaglebone hardware. Include a check for this board type and configure DDR3. The timings and other configuration match EVM SK. Signed-off-by: Joel A Fernandes <joelagnel@ti.com> Acked-by: Jason Kridner <jdk@ti.com>
2012-10-22ARM : Remove unused CONFIG_DRIVER_SMC91111, CONFIG_DRIVER_LAN91C96Ashok
Remove unused CONFIG_DRIVER_SMC91111,CONFIG_DRIVER_LAN91C96, if required implement smc_set_mac_addr() in board init. Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com> Acked-by: Tom Rini <trini@ti.com>
2012-10-22common: Discard the __u_boot_cmd sectionMarek Vasut
The command declaration now uses the new LG-array method to generate list of commands. Thus the __u_boot_cmd section is now superseded and redundant and therefore can be removed. Also, remove externed symbols associated with this section from include/command.h . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org>
2012-10-22common: Convert the U-Boot commands to LG-arraysMarek Vasut
This patch converts the old method of creating a list of command onto the new LG-arrays code. The old u_boot_cmd section is converted to new u_boot_list_cmd subsection and LG-array macros used as needed. Minor adjustments had to be made to the common code to work with the LG-array macros, mostly the fixup_cmdtable() calls are now passed the ll_entry_start and ll_entry_count instead of linker-generated symbols. The command.c had to be adjusted as well so it would use the newly introduced LG-array API instead of directly using linker-generated symbols. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org>
2012-10-22common: Add .u_boot_list into all linker filesMarek Vasut
Add section for the linker-generated lists into all possible linker files, so that everyone can easily use these lists. This is mostly a mechanical adjustment. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org>
2012-10-19Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
Conflicts: drivers/serial/serial_lh7a40x.c Signed-off-by: Tom Rini <trini@ti.com>
2012-10-19arm: Change global data baudrate to intSimon Glass
This does not need to be a long, so change it. Also adjust bi_baudrate to be unsigned. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-19arm: fdt: Relocate fdt along with other dataSimon Glass
Rather than leave the fdt down next to the code/data, we really should relocate it along with everything else. For CONFIG_OF_EMBED this happens automatically, but for CONFIG_OF_SEPARATE it does not. Add code to copy the fdt and point to the new copy after relocation. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com>
2012-10-18dm: Move s3c24xx USB driver to a proper placeMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: David Müller <d.mueller@elsoft.ch> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de>
2012-10-18dm: wdt: arm: Move tnetv107x into drivers/watchdog/Marek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Oliver Brown <obrown@adventnetworks.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de>
2012-10-17ARM: at91sam9x5: enable MCI0 support for 9x5ek board.Wu, Josh
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>