aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/include/asm
AgeCommit message (Collapse)Author
2013-02-07board: samsung: Update MAC address for Arndale board through GUID2013.02.2Tushar Behera
There are a couple of GUID (Global Unique Identifier) registers within EXYNOS5250 SoC. The values of these GUID registers are set as board MAC address. Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
2013-02-04arndale5250: Boot in Hyp mode and enable architected timersChristoffer Dall
First, to boot in Hyp mode we need to change to non-secure mode, which involves configuring the frequency of the arch. timers and setting all interrupts on the gic to group 1 (this code was inspired by the boot wrapper code). Second, signal the secondary CPU while still in secure mode and have the secondary CPU run the SPL. The SPL checks the hardware cpu id, and if it's a secondary CPU, it will initialize non-secure mode inside the SPL, enter Hyp mode, and finally enter a new SMP pen with the same poking stick interface as the regular kernel uses. Third, on CPU0 we wait until u-boot is fully up to actually enter the non-secure mode on CPU0, and stay in non-secure svc mode right up until we actually load the kernel, where the last thing we do is enter Hyp mode. Let it roll... Signed-off-by: Jeremy C. Andrus <jeremya@cs.columbia.edu> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2012-12-06ARM: highbank: set timer prescaler to 256Rob Herring
The 150MHz clock rate gives u-boot time functions problems and there's no benefit to a fast clock, so lower the rate. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-12-06DRIVERS: USB: Initialize HSIC PHYs and enable network supportInderpal Singh
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo controller, connected to HSIC Phy of USB host controller via USB3503 hub. This patch initializes the HSIC PHYs, performs reset sequence for USB3503 hub and enables the relevant config options for network to work. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
2012-12-06EXYNOS: mmc: support DesignWare Controller for Samsung-SoCJaehoon Chung
Support DesignWare MMC Controller for Samsung Specific. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Rajeshawari Shinde <rajeshwari.s@samsung.com>
2012-12-06EXYNOS: clock: add the get_mmc_clk functionJaehoon Chung
To get more exactly sclk value, used the get_mmc_clk. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2012-12-06EXYNOS: additional Exynos4 SoC series supportJeong-Hyeon Kim
- Fixed MPLL register address It's different between Exynos4210 and Exynos4412. - Added pinmux functions for Exynos4 - Added extended gpios for Exynos4412 Exynos4412 has more gpios than Exynos4210. Signed-off-by: Jeong-Hyeon Kim <jhkim@insignal.co.kr>
2012-12-06gpio:fix: Proper handling of GPIO subsystem parts at Samsung devicesŁukasz Majewski
Now proper GPIO parts numbering is handled at Samsung devices. This fix is necessary for code using GPIO located at other banks than first. Test HW: - Exynos4210 - Trats - S5PC110 - goni Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-12-06Revert "armv7: adapt omap3 to the new cache maintenance framework"Ricardo Salveti de Araujo
This reverts commit 45bf05854bc94ed8bae9e9114292895b990327ea. Conflicts: arch/arm/cpu/armv7/omap3/board.c arch/arm/cpu/armv7/omap3/lowlevel_init.S arch/arm/include/asm/arch-omap3/sys_proto.h Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
2012-12-06SAUCE: HACK: move omap spl base addressJohn Rigby
Move NON_SECURE_SRAM_START from 0x40304000 to 0x40303000 and move u-boot-spl load address from 0x40304350 to 0x40303080. This allows it to stay under 0x4030c000 which is what the TRM says it must do. SRAM actually starts at 0x40300000 on GP devices but was set to 0x40304000 to be the same as Secure devices so this breaks that. Signed-off-by: John Rigby <john.rigby@linaro.org>
2012-12-06OMAP3: Beagle: set mac addr from dieidJohn Rigby
TODO: share dieid<-->mac addr code between OMAP3 and OMAP4 Signed-off-by: John Rigby <john.rigby@linaro.org>
2012-12-06OMAP4 Panda: Generate a unique usbethaddrJohn Rigby
The panda board has a usb nic but the nic has no rom. Use the die-id to generate a unique address. This is derived from an RFC kernel patch by Andy Green that does the same thing: https://patchwork.kernel.org/patch/660541/ [RFC PATCH 1/2] OMAP2+: add cpu id register to MAC address helper Signed-off-by: John Rigby <john.rigby@linaro.org>
2012-12-06OMAP4: Panda: Add usb peripheral bootJohn Rigby
Stripped down fastboot protocol for now but could be just about anything. Will revisit once a fastboot or dfu implementation hits upstream. Signed-off-by: John Rigby <john.rigby@linaro.org> Conflicts: arch/arm/cpu/armv7/omap-common/Makefile arch/arm/include/asm/omap_common.h common/spl/spl.c include/configs/omap4_common.h spl/Makefile
2012-10-26arm: Remove support for NETARMMarek Vasut
This stuff has been rotting in the tree for a while now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for s3c4510Marek Vasut
This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for lpc2292Marek Vasut
This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26Merge remote-tracking branch 'u-boot-ti/master'Albert ARIBAUD
2012-10-25am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbersPeter Korsgaard
So other parts can be added. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: support board specific ddr settingsPeter Korsgaard
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code, so other boards can use different types/timings. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make apply with rtc32k_enable() in the file] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx: move generic parts of pinmux handling out from board/ti/am335xPeter Korsgaard
So they are available for other boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: move ti i2c baseboard header handling to board/ti/am335x/Peter Korsgaard
The i2c header is specific to ti(-derived) boards, and not generic for all am335x boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make re-apply with rtc32k_enable() applied] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx: Add SPI SPL as an optionTom Rini
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE define. Finally, enable the options on the am335x_evm. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25VIDEO: add macro to set LCD size for DSS driverStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-10-25am335x: Enable RTC 32K OSC clockVaibhav Hiremath
In order to support low power state, you must source kernel system timers to persistent clock, available across suspend/resume. In case of AM335x device, the only source we have is, RTC32K, available in wakeup/always-on domain. Having said that, during validation it has been observed that, RTC clock need couple of seconds delay to stabilize the RTC OSC clock; and such a huge delay is not acceptable in kernel especially during early init and also it will impact quick/fast boot use-cases. So, RTC32k OSC enable dependency has been shifted to SPL/first-bootloader. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-19arm: Change global data baudrate to intSimon Glass
This does not need to be a long, so change it. Also adjust bi_baudrate to be unsigned. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15mx25: Clean up lowlevel_initBenoît Thébaudeau
Clean up mx25 lowlevel_init: - Add comments. - Do not use write32 repeatedly with the same value in order not to increase code size. - Make register values configurable. - Use macro parameters with default values instead of literal constants. - Use defined macros instead of duplicating code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: John Rigby <jcrigby@gmail.com> Cc: Matthias Weisser <weisserm@arcor.de>
2012-10-15mx31: Fix PDR0_CSI_PODFBenoît Thébaudeau
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0 register is actually composed of two bit-fields: one pre-divider and one post-divider. This patch fixes the CCM access macros and the code using them accordingly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx35: Define MAX and AIPS registersBenoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx31: Add more CCM access macrosBenoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Clean up clocks APIBenoît Thébaudeau
Use the standard mxc_get_clock() instead of exporting internal functions and using literal constant values. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25 clocks: Fix MXC_FEC_CLKBenoît Thébaudeau
mxc_get_clock(MXC_FEC_CLK) should return the IPG clock, not the AHB clock. Also, imx_get_fecclk() was correct but reimplemented the calculation of the IPG clock, so remove the duplicated code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Define more standard clocksBenoît Thébaudeau
Define AHB, IPG and CSPI clocks. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5/6 clocks: Fix SDHC clocksBenoît Thébaudeau
The i.MX5 eSDHC clocks were considered as coming from the IPG clock although they have dedicated clock paths. Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15mx5 clocks: Fix get_lp_apm()Benoît Thébaudeau
If CCM.CCSR.lp_apm is set, the lp_apm clock is not necessarily 32768 Hz x 1024. In that case: - on i.MX51, this clock comes from the output of the FPM, - on i.MX53, this clock comes from the output of PLL4. This patch fixes the code accordingly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Add and use CCSR definitionsBenoît Thébaudeau
This fixes config_pll_clk(), which used 0x20 instead of 0x200 for PLL4_CLOCK. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx51: Fix USB PHY clocksBenoît Thébaudeau
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks have different clock gate control bit-fields. The existing code was correct only for i.MX53, so this patch fixes the i.MX51 use case. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Jana Rapava <fermata7@gmail.com> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il>
2012-10-15mx5: Fix clock gate valuesBenoît Thébaudeau
The clock gate values are 2-bit bit-fields. Hence, setting or clearing only one of these bits like what was done is wrong and can lead to unpredictable behavior depending on the original value of these bit-fields. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5: Use explicit clock gate namesBenoît Thébaudeau
Use clock gate definitions having names showing clearly the gated clock instead of names giving only a register field index. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: CleanupBenoît Thébaudeau
Clean up the i.MX5 clock driver: - Use readl() and writel() instead of their __raw_ counterparts. - Use the clr/setbits_le32() family of macros rather than expanding code. - Use accessor macros for bit-fields instead of _MASK and _OFFSET. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5/6: Define default SoC input clock frequenciesBenoît Thébaudeau
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <r64343@freescale.com> Cc: Matt Sealey <matt@genesi-usa.com> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15imx: Use MXC_I2C_CLK in imx i2c driverMatthias Weisser
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using MXC_I2C_CLK on all imx systems using i2c. Signed-off-by: Matthias Weisser <weisserm@arcor.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: add CPU revision 1.2Eric Benard
tested on a MCIMX257CJM4A which now reports : CPU: Freescale i.MX25 rev1.2 at 399 MHz Signed-off-by: Eric Bénard <eric@eukrea.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15i.MX6: get rid of redundant struct src_regs (dupe of struct src)Eric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: define struct iomuxc and IOMUX_GPR2 register bitfieldsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15i.MX6: Add ANATOP_PFD_480 bitfield constantsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15i.MX6: define IOMUX_GPR3 register bitfieldsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: define bitfields for CHSCCDR registerEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: change register name for CCM_CHSCCDR to match ref. manualEric Nelson
Register CCM_CHSCCDR (offset 0x34 in CCM) is named CCM_CHSCCDR in reference manual, but was named chscdr in struct mxc_ccm_reg. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: provide functional names for CCM_CCGR0-CCGR6 bit fieldsEric Nelson
Add meaningful constants for each clock channels and use them for enabling and disabling i.MX6 clocks. Includes an update to enable/disable the IPU1 clock in drivers/video/ipu_common to remove IMX5x register access when used on i.MX6 as discussed in V1: http://patchwork.ozlabs.org/patch/185129/ Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15pxa: Add code to examine cpu model and revisionLukasz Dalek
Add function which return CPU model and revision which can be used for cpu detection. Signed-off-by: Lukasz Dalek <luk0104@gmail.com>