diff options
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/ich8lan.c | 13 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/mac.c | 13 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/netdev.c | 2 |
3 files changed, 9 insertions, 19 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c index 7ddac956ffb5..f3aaca743ea3 100644 --- a/drivers/net/ethernet/intel/e1000e/ich8lan.c +++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c @@ -1364,9 +1364,6 @@ out: * Checks to see of the link status of the hardware has changed. If a * change in link status has been detected, then we read the PHY registers * to get the current speed/duplex if link exists. - * - * Returns a negative error code (-E1000_ERR_*) or 0 (link down) or 1 (link - * up). **/ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) { @@ -1382,7 +1379,7 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) * Change or Rx Sequence Error interrupt. */ if (!mac->get_link_status) - return 1; + return 0; /* First we want to see if the MII Status Register reports * link. If so, then we want to get the current speed/duplex @@ -1600,7 +1597,7 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) * we have already determined whether we have link or not. */ if (!mac->autoneg) - return 1; + return -E1000_ERR_CONFIG; /* Auto-Neg is enabled. Auto Speed Detection takes care * of MAC speed/duplex configuration. So we only need to @@ -1614,12 +1611,10 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) * different link partner. */ ret_val = e1000e_config_fc_after_link_up(hw); - if (ret_val) { + if (ret_val) e_dbg("Error configuring flow control\n"); - return ret_val; - } - return 1; + return ret_val; } static s32 e1000_get_variants_ich8lan(struct e1000_adapter *adapter) diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c index db735644b312..b322011ec282 100644 --- a/drivers/net/ethernet/intel/e1000e/mac.c +++ b/drivers/net/ethernet/intel/e1000e/mac.c @@ -410,9 +410,6 @@ void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw) * Checks to see of the link status of the hardware has changed. If a * change in link status has been detected, then we read the PHY registers * to get the current speed/duplex if link exists. - * - * Returns a negative error code (-E1000_ERR_*) or 0 (link down) or 1 (link - * up). **/ s32 e1000e_check_for_copper_link(struct e1000_hw *hw) { @@ -426,7 +423,7 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw) * Change or Rx Sequence Error interrupt. */ if (!mac->get_link_status) - return 1; + return 0; /* First we want to see if the MII Status Register reports * link. If so, then we want to get the current speed/duplex @@ -450,7 +447,7 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw) * we have already determined whether we have link or not. */ if (!mac->autoneg) - return 1; + return -E1000_ERR_CONFIG; /* Auto-Neg is enabled. Auto Speed Detection takes care * of MAC speed/duplex configuration. So we only need to @@ -464,12 +461,10 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw) * different link partner. */ ret_val = e1000e_config_fc_after_link_up(hw); - if (ret_val) { + if (ret_val) e_dbg("Error configuring flow control\n"); - return ret_val; - } - return 1; + return ret_val; } /** diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index dfde22e9a8b6..6855b3380a83 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -5074,7 +5074,7 @@ static bool e1000e_has_link(struct e1000_adapter *adapter) case e1000_media_type_copper: if (hw->mac.get_link_status) { ret_val = hw->mac.ops.check_for_link(hw); - link_active = ret_val > 0; + link_active = !hw->mac.get_link_status; } else { link_active = true; } |