| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sisfb incorrectly sets the length of the color fields to 6 bits
for PSEUDOCOLOR modes, even though 8 bits are always used per pixel.
Fix this by setting the length to 8.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sa1100fb incorrectly sets the length of the color fields to 8 bits for
PSEUDOCOLOR modes for which only 4 bits are used per pixel. Fix this by
setting the length to 4 bits for these modes.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
s3fb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 or 4 bits are used per pixel. Fix this
by setting the length to 8 or 4, respectively.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf
These sensors communicate over a 2 wire bus running a device specific
protocol. The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available. This is handled by
an interrupt that is disabled under all other conditions.
I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!
Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem. If not it should be provided in the
platform data.
I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
efifb will attempt to ioremap a framebuffer even if its starting address
is 0, failing and causing an ugly backtrace in the process. Exit before
probing if this is the case.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
uvesafb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 bits are always used per pixel. Fix this
by setting the length to 8.
The switch of the DAC width from the default 6 bits to 8 bits is retained
and tracked internally in the driver, but never exposed to userspace.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The documentation about the meaning of the color component bitfield
lengths in pseudocolor modes is inconsistent. Fix it, so that it
indicates the correct interpretation everywhere, i.e. that 1 << length is
the number of palette entries.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Acked-by: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fb_notifier_call_chain() is called with info->lock held, i.e. in
do_fb_ioctl() => FBIOPUT_VSCREENINFO => fb_set_var() and the some
notifier callbacks, like fbcon_event_notify(), try to re-acquire
info->lock again.
Remove the lock/unlock_fb_info() in all the framebuffer notifier
callbacks' and be sure to always call fb_notifier_call_chain() with
info->lock held.
Reported-by: Pavel Roskin <proski@gnu.org>
Reported-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove unused #include <version.h> in drivers/hwmon/hp_accel.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: fix obviously wrong comment
ahci: force CAP_NCQ for earlier NV MCPs
[libata] sata_via: kill uninit'd var warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits)
Input: i8042 - add HP DV9700 to the noloop list
Input: arrange drivers/input/misc/Makefile in alphabetical order
Input: add AD7879 Touchscreen driver
Input: add AD7877 touchscreen driver
Input: bf54x-keys - fix typo in warning
Input: add driver for S1 button of rb532
Input: generic driver for rotary encoders on GPIOs
Input: hilkbd - fix crash when removing hilkbd module
Input: atkbd - add quirk for Fujitsu Siemens Amilo PA 1510
Input: atkbd - consolidate force release quirk setup
Input: add accelerated touchscreen support for Marvell Zylonite
Input: ucb1400_ts, mainstone-wm97xx - add BTN_TOUCH events
Input: wm97xx - use disable_irq_nosync() for Mainstone
Input: wm97xx - add BTN_TOUCH event to wm97xx to use it with Android
Input: fix polling of /proc/bus/input/devices
Input: psmouse - add newline to OLPC HGPK touchpad debugging
Input: ati_remote2 - check module params
Input: ati_remote2 - add per device attrs
Input: ati_remote2 - complete suspend support
Input: stop autorepeat timer on key release
...
|
|
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.infradead.org/iommu-2.6:
intel-iommu: Avoid panic() for DRHD at address zero.
Intel-IOMMU Alignment Issue in dma_pte_clear_range()
|
|
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Let new-style drivers implement attach_adapter
i2c: Fix sparse warnings for I2C_BOARD_INFO()
i2c-voodoo3: Deprecate in favor of tdfxfb
i2c-algo-pca: Fix use of uninitialized variable in debug message
|
|
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: just ignore invalid GPIOs in leds-gpio
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] omap_wdt.c: move probe function to .devinit.text
[WATCHDOG] ks8695_wdt.c: move probe function to .devinit.text
[WATCHDOG] at91rm9200_wdt.c: move probe function to .devinit.text
[WATCHDOG] remove ARM26 sections
[WATCHDOG] orion5x_wdt: Add shutdown callback, use watchdog ping function
[WATCHDOG] i6300esb.c: Restructure initialization of the device
[WATCHDOG] i6300esb.c: Fix the GETSTATUS and GETBOOTSTATUS ioctls.
[WATCHDOG] i6300esb.c: Cleanup
|
|
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (60 commits)
microblaze_v8: Add MAINTAINERS fragment
microblaze_v8: Uartlite for Microblaze
microblaze_v8: Makefiles for Microblaze cpu
microblaze_v8: Kconfig patches
microblaze_v8: Interrupt handling and timer support
microblaze_v8: syscalls.h
microblaze_v8: pci headers
microblaze_v8: Kbuild file
microblaze_v8: string.h thread_info.h
microblaze_v8: unistd.h
microblaze_v8: fcntl.h sockios.h ucontext.h
microblaze_v8: pool.h socket.h
microblaze_v8: device.h param.h topology.h
microblaze_v8: headers files entry.h current.h mman.h registers.h sembuf.h
microblaze_v8: namei.h
microblaze_v8: gpio.h, serial.h
microblaze_v8: headers simple files - empty or redirect to asm-generic
microblaze_v8: sigcontext.h siginfo.h
microblaze_v8: termbits.h termios.h
microblaze_v8: stats headers
...
|
|
While it isn't the way the standard device binding model works, it is
OK for new-style drivers to implement attach_adapter. It may help
convert the renaming legacy drivers to new style drivers faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
|
|
Support for I2C/DDC was recently added to the tdfxfb driver, which
means that the i2c-voodoo3 driver can be deprecated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
|
|
A recent change broke debugging of pca_xfer(), fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Also remove the now-useless debug printouts which are supposed to
tell us when the scan starts and ends.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Along with MCP65, MCP67 and 73 also don't set CAP_NCQ. Force it.
Reported by zaceni@yandex.ru on bko#13014 and confirmed by Peer Chen.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: NightFox <zaceni2@yandex.ru>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Reported and initial patch by Marin Mitov.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This reverts commit 5d38258ec026921a7b266f4047ebeaa75db358e5, since the
underlying problem got fixed properly in the previous commit ("async:
Fix module loading async-work regression").
Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the BIOS does something obviously stupid, like claiming that the
registers for the IOMMU are at physical address zero, then print a nasty
message and abort, rather than trying to set up the IOMMU and then later
panicking.
It's becoming more and more obvious that trusting this stuff to the BIOS
was a mistake.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
* git://git.infradead.org/~dwmw2/firmware-2.6:
qla1280: Fix off-by-some error in firmware loading.
Add README.AddingFirmware file. Basically telling people not to.
firmware: Remove newly-added slicoss and sxg firmware images
firmware/WHENCE: Add missing origin information for Ambassador atmsar11.fw
ALSA: wavefront - Always use request_firmware()
Remove fdump tool for av7110 firmware
firmware: convert av7110 driver to request_firmware()
Partially revert "V4L/DVB (9533): cx88: Add support for TurboSight TBS8910 DVB-S PCI card"
Revert "fix modules_install via NFS"
Add-add conflicts in firmware/WHENCE fixed manually
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
Separate out the proc- and unit-specific header directories from the general
Move arch headers from include/asm-mn10300/ to arch/mn10300/include/asm/.
|
|
MN10300 arch headers and place them instead in the same directories as contain
the .c files for the processor and unit implementations.
This permits the symlinks include/asm/proc and include/asm/unit to be
dispensed with. This does, however, require that #include <asm/proc/xxx.h> be
converted to #include <proc/xxx.h> and similarly for asm/unit -> unit.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (27 commits)
xsysace: Fix dereferencing of cf_id after hd_driveid removal
at91_ide: turn on PIO 6 support
at91_ide: remove unused ide_mm_{outb,inb}
ide-cd: reverse NOT_READY sense key logic
ide: refactor tf_read() method
ide: refactor tf_load() method
ide: call write_devctl() method from tf_read() method
ide: move common code out of tf_load() method
ide: simplify 'struct ide_taskfile'
ide: replace IDE_TFLAG_* flags by IDE_VALID_*
ide-cd: fix intendation in cdrom_decode_status()
ide-cd: unify handling of fs and pc requests in cdrom_decode_status()
ide-cd: convert cdrom_decode_status() to use switch statements
ide-cd: update debugging support
ide-cd: respect REQ_QUIET for fs requests in cdrom_decode_status()
ide: remove unused #include <linux/version.h>
tx4939ide: Fix tx4939ide_{in,out}put_data_swap argument
tx493[89]ide: Remove big endian version of tx493[89]ide_tf_{load,read}
ide-cd: carve out an ide_cd_breathe()-helper for fs write requests
ide-cd: move status checking into the IRQ handler
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add support for new SFP+ PHY
RDMA/nes: Add wide_ppm_offset parm for switch compatibility
RDMA/nes: Fix SFP+ PHY initialization
RDMA/nes: Fix nes_nic_cm_xmit() error handling
RDMA/nes: Fix error handling issues
RDMA/nes: Fix incorrect casts on 32-bit architectures
IPoIB: Document newish features
RDMA/cma: Create cm id even when IB port is down
RDMA/cma: Use rate from IPoIB broadcast when joining IPoIB multicast groups
IPoIB: Avoid free_netdev() BUG when destroying a child interface
mlx4_core: Don't leak mailbox for SET_PORT on Ethernet ports
RDMA/cxgb3: Release dependent resources only when endpoint memory is freed.
RDMA/cxgb3: Handle EEH events
IB/mlx4: Use pgprot_writecombine() for BlueFlame pages
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm kcopyd: fix callback race
dm kcopyd: prepare for callback race fix
dm: implement basic barrier support
dm: remove dm_request loop
dm: rework queueing and suspension
dm: simplify dm_request loop
dm: split DMF_BLOCK_IO flag into two
dm: rearrange dm_wq_work
dm: remove limited barrier support
dm: add integrity support
|
|
|
|
* git://git.infradead.org/battery-2.6:
pda_power: Add optional OTG transceiver and voltage regulator support
pcf50633_charger: Remove unused mbc_set_status function
pcf50633_charger: Enable periodic charging restart
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
igb: remove sysfs entry that was used to set the number of vfs
igbvf: add new driver to support 82576 virtual functions
drivers/net/eql.c: Fix a dev leakage.
niu: Fix unused variable warning.
r6040: set MODULE_VERSION
bnx2: Don't use reserved names
FEC driver: add missing #endif
niu: Fix error handling
mv643xx_eth: don't reset the rx coal timer on interface up
smsc911x: correct debugging message on mii read timeout
ethoc: fix library build errors
netfilter: ctnetlink: fix regression in expectation handling
netfilter: fix selection of "LED" target in netfilter
netfilter: ip6tables regression fix
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Hook up sys_preadv and sys_pwritev
sparc64: add_node_ranges() must be __init
serial: sunsu: sunsu_kbd_ms_init needs to be __devinit
sparc: Fix section mismatch warnings in cs4231 sound driver.
sparc64: Fix section mismatch warnings in PCI controller drivers.
sparc64: Fix section mismatch warnings in power driver.
sparc64: get_cells() can't be marked __init
|
|
If the thread calling dm_kcopyd_copy is delayed due to scheduling inside
split_job/segment_complete and the subjobs complete before the loop in
split_job completes, the kcopyd callback could be invoked from the
thread that called dm_kcopyd_copy instead of the kcopyd workqueue.
dm_kcopyd_copy -> split_job -> segment_complete -> job->fn()
Snapshots depend on the fact that callbacks are called from the singlethreaded
kcopyd workqueue and expect that there is no racing between individual
callbacks. The racing between callbacks can lead to corruption of exception
store and it can also mean that exception store callbacks are called twice
for the same exception - a likely reason for crashes reported inside
pending_complete() / remove_exception().
This patch fixes two problems:
1. job->fn being called from the thread that submitted the job (see above).
- Fix: hand over the completion callback to the kcopyd thread.
2. job->fn(read_err, write_err, job->context); in segment_complete
reports the error of the last subjob, not the union of all errors.
- Fix: pass job->write_err to the callback to report all error bits
(it is done already in run_complete_job)
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Use a variable in segment_complete() to point to the dm_kcopyd_client
struct and only release job->pages in run_complete_job() if any are
defined. These changes are needed by the next patch.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Barriers are submitted to a worker thread that issues them in-order.
The thread is modified so that when it sees a barrier request it waits
for all pending IO before the request then submits the barrier and
waits for it. (We must wait, otherwise it could be intermixed with
following requests.)
Errors from the barrier request are recorded in a per-device barrier_error
variable. There may be only one barrier request in progress at once.
For now, the barrier request is converted to a non-barrier request when
sending it to the underlying device.
This patch guarantees correct barrier behavior if the underlying device
doesn't perform write-back caching. The same requirement existed before
barriers were supported in dm.
Bottom layer barrier support (sending barriers by target drivers) and
handling devices with write-back caches will be done in further patches.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Remove queue_io return value and a loop in dm_request.
IO may be submitted to a worker thread with queue_io(). queue_io() sets
DMF_QUEUE_IO_TO_THREAD so that all further IO is queued for the thread. When
the thread finishes its work, it clears DMF_QUEUE_IO_TO_THREAD and from this
point on, requests are submitted from dm_request again. This will be used
for processing barriers.
Remove the loop in dm_request. queue_io() can submit I/Os to the worker thread
even if DMF_QUEUE_IO_TO_THREAD was not set.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Rework shutting down on suspend and document the associated rules.
Drop write lock in __split_and_process_bio to allow more processing
concurrency.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Refactor the code in dm_request().
Require the new DMF_BLOCK_FOR_SUSPEND flag on readahead bios we will
discard so we don't drop such bios while processing a barrier.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Split the DMF_BLOCK_IO flag into two.
DMF_BLOCK_IO_FOR_SUSPEND is set when I/O must be blocked while suspending a
device. DMF_QUEUE_IO_TO_THREAD is set when I/O must be queued to a
worker thread for later processing.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Refactor dm_wq_work() to make later patch more readable.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Prepare for full barrier implementation: first remove the restricted support.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This patch provides support for data integrity passthrough in the device
mapper.
- If one or more component devices support integrity an integrity
profile is preallocated for the DM device.
- If all component devices have compatible profiles the DM device is
flagged as capable.
- Handle integrity metadata when splitting and cloning bios.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This patch removes the sysfs entry num_vfs which was added to support
enabling pci virtual functions for 82576.
To prevent VFs from loading automatically a module parameter "max_vfs" was
added so that the number of VFs per PF can be limited. This is especially
useful when 4 or more 82576 ports are on the system because otherwise to
load all VFs would result in 8 interface per physical port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds an igbvf driver to handle virtual functions provided by the
igb driver when SR-IOV has been enabled. A virtual function is a
lightweight pci-e function that supports a single queue and shares
resources with the 82576 physical function contained within the igb
driver.
To spawn virtual functions from the igb driver all that is needed is to
enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that
supports SR-IOV in the BIOS. The virtual functions will appear after the
interface is loaded.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After dev_get_by_name(), we should follow a dev_put().
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't strain gcc's tiny mind.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
