| Age | Commit message (Collapse) | Author |
|---|
|
Patch b3c1e01a09d6af2dd7811a066ffcfc5171be2bed should do it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
The Microblaze dynamic ftrace code assumes a call ordering that is not met
in all scenarios. Specifically, executing a command similar to:
echo 105 > /sys/kernel/debug/tracing/set_ftrace_pid
before any other tracing-related commands results in a kernel panic:
BUG: failure at arch/microblaze/kernel/ftrace.c:198/ftrace_update_ftrace_func()!
Recoding ftrace_update_ftrace_func() to use &ftrace_caller directly eliminates
the need to capture its address elsewhere (and thus rely on a particular call
sequence).
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
|
|
If early printk console is not enabled then all messages
are written to log buffer.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
I forget to change register name in comments.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
TLB size was hardcoded in asm code. This patch brings ability
to change TLB size only in one place. (mmu.h).
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
On the base on GCOV analytics is helpful to add likely/unlikely
macros.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Cachegrind analysis need this fix to be able to log asm functions.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Sync labels.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
RESR and REAR uses the same regs in whole file.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This change synchronize register usage in code.
ESR = R4
EAR = R3
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Any sync branch must follow mts instructions not mfs.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Disable debug option in asm code.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
When the system has no lmb bram, main memory should be start from
zero because of microblaze vectors.
DTS fragment could look like:
DDR2_SDRAM: memory@0 {
device_type = "memory";
reg = < 0x0 0x10000000 >;
} ;
Then you have to setup CONFIG_KERNEL_BASE_ADDR=0 which caused
that kernel physical start address will be zero. On reset vector place
will be jump to 0x100 and on 0x100 starts kernel text.
You have to solve how to load the kernel before cpu starts.
Tested with XMD.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
I would like to use asm-generic uaccess.h where are segment
macros defined. This is just first step.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
The "kstack=" command line parameter is not parsed correctly.
All proper values are interpreted as zero.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (27 commits)
microblaze: entry.S use delay slot for return handlers
microblaze: Save current task directly
microblaze: Simplify entry.S - save/restore r3/r4 - ret_from_trap
microblaze: PCI early support for noMMU system
microblaze: Fix dma alloc and free coherent dma functions
microblaze: Add consistent code
microblaze: pgtable.h: move consistent functions
microblaze: Remove ancient Kconfig option for consistent mapping
microblaze: Remove VMALLOC_VMADDR
microblaze: Add define for ASM_LOOP
microblaze: Preliminary support for dma drivers
microblaze: remove trailing space in messages
microblaze: Use generic show_mem()
microblaze: Change temp register for cmdline
microblaze: Preliminary support for dma drivers
microblaze: Move cache function to cache.c
microblaze: Add support from PREEMPT
microblaze: Add support for Xilinx PCI host bridge
microblaze: Enable PCI, missing files
microblaze: Add core PCI files
...
|
|
Use the generic ptrace_resume code for PTRACE_SYSCALL, PTRACE_CONT and
PTRACE_KILL. This also makes PTRACE_SINGLESTEP return -EIO while it
previously succeeded despite not actually causing any kind of single
stepping.
Also the TIF_SYSCALL_TRACE thread flag is now cleared on PTRACE_KILL which
it previously wasn't which is consistent with all architectures using the
modern ptrace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Cc: John Williams <john.williams@petalogix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use ptrace_request() in the three remaining architectures that didn't use it
(m68knommu, h8300, microblaze). This means:
- ptrace_request now handles PTRACE_{PEEK,POKE}{TEXT,DATA} and PTRACE_DETATCH
calls that were previously called directly, or in case of h8300 even open
coded.
- adds new support for PTRACE_SETOPTIONS/PTRACE_GETEVENTMSG/
PTRACE_GETSIGINFO/PTRACE_SETSIGINFO
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
There is possible to save r3/r4 at the beggining of user part
before calling handlers and at the end restore it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
We have to use consistent code to be able to do coherent dma
function. In consistent code is used cache inhibit page mapping.
Xilinx reported that there is bug in Microblaze for WB and
d-cache_always use option. Microblaze 7.30.a should be first version
where is this bug removed.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
It is default option but both options must be measured.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
I found several problems for ll_temac driver and on system with WB.
This early fix should fix it. I will clean this patch before I will add
it to mainline
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
For copy was used r7 register when CONFIG_CMDLINE_BOOL option
is enabled. But r7 stores pointer to fdt that's why machine_early_init
not detect compiled-in DTB.
I also moved kernel PID setup to have TLB init in one block
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
I found several problems for ll_temac driver and on system with WB.
This early fix should fix it. I will clean this patch before I will add
it to mainline
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
It is better to have init cache handling on one place.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This patch add core PREEMPT support for Microblaze.
I tried to trace it via tracers and I was able to see any output.
I also added low level debug functions to see if that code is called.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This patch is based on powerpc patch
64f16502475ddf663169369fffff6da9b10ea9fb
We did some cleanups and removed powerpc parts.
There is one new debug early listing function too.
Exclude function is only in Debug options.
We tested in on custom board.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Support function for PCI. We don't use any advance mapping mechanism
that's why implementation is simple.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
There is necessary to do some cache handling for dma operations.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Add DMA support for Microblaze. There are some part of this new feature:
1. Basic DMA support
2. Enable DMA debug option
3. Setup notifier
Ad 1. dma-mapping come from powerpc and x86 version and it is based on
generic dma-mapping-common.h
Ad 2. DMA support debug features which is used in generic file.
For more information please look at Documentation/DMA-API.txt
Ad 3. notifier is very important to setup dma_ops. Without this part
for example ll_temac driver failed because there are no setup dma operations.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
|
|
I create wrong asm code but none test shows that this part of code is wrong.
I am not convinces that were good idea to create asm optimized macros
for caches. The reason is that there is not optimization with previous code
that's why make sense to add old code and do some benchmarking which
functions are faster.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Rather than defining of_chosen in each arch, it can be defined for all
in driver/of/base.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
We don't always have lmb available, so make arches provide an
early_init_dt_alloc_memory_arch() to handle the allocation of
memory in the fdt code.
When we don't have lmb.h included, we need asm/page.h for __va.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
At present, the fdt code sets the kernel-wide initrd_start and
initrd_end variables when parsing /chosen. On ARM, we only set these
once the bootmem has been reserved.
This change adds an arch hook to setup the initrd from the device
tree:
void early_init_dt_setup_initrd_arch(unsigned long start,
unsigned long end);
The arch-specific code can then setup the initrd however it likes.
Compiled on powerpc, with CONFIG_BLK_DEV_INITRD=y and =n.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Merge common code between PowerPC and Microblaze architectures.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
Merge common function between powerpc, sparc and microblaze. Code is
identical for powerpc and microblaze, but adds a lock (and release) of
the devtree_lock on sparc.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Merge common code between PowerPC and Microblaze
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Microblaze only has one CPU, it isn't SMP at all. early_init_dt_scan_cpus()
is effectively just a no-op, so remove it.
Microblaze doesn't support hypervisor assisted dump either, so the phyp stuff
can also go.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
We found that on write-trough kernel is necessary to do that invalidation.
One WB is possible to use invalidation too.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Interrupts must be disabled while an interrupt state restore
(prep for interrupt return) is in progress.
Code to do this was lost in the port to the mainline kernel.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
|
|
In struct device_node, the phandle is named 'linux_phandle' for PowerPC
and MicroBlaze, and 'node' for SPARC. There is no good reason for the
difference, it is just an artifact of the code diverging over a couple
of years. This patch renames both to simply .phandle.
Note: the .node also existed in PowerPC/MicroBlaze, but the only user
seems to be arch/powerpc/platforms/powermac/pfunc_core.c. It doesn't
look like the assignment between .linux_phandle and .node is
significantly different enough to warrant the separate code paths
unless ibm,phandle properties actually appear in Apple device trees.
I think it is safe to eliminate the old .node property and use
phandle everywhere.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge common code between PowerPC and MicroBlaze
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge common code between PowerPC and Microblaze
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
