| Age | Commit message (Collapse) | Author |
|---|
|
The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic. This
changes it to the following behavior:
- when setting GPIOs, ignore the higher order bits (they're for
clearing, we don't need to care about them).
- when clearing GPIOs, keep all the bits, but unset (via XOR) the
lower order bit that negates the clear bit that we care about. That
is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
currently in the register with 0x0400 (GPIO 26's SET bit), and then
OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.
This means that read-modify-write doesn't actually work for it, so don't
apply the errata here. If a negative edge status gets lost after
resume.. well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If pcie_ports_disabled is set, pcie_port_service_register() returns
error code and select_detection_mode() should not attempt to
unregister dummy_driver and use dummy_slots. It should return
PCIEHP_DETECT_ACPI immediately instead.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This reverts commit 4465b469008bc03b98a1b8df4e9ae501b6c69d4b.
Conflicts:
net/ipv4/fib_frontend.c
As reported by Ben Greear, this causes regressions:
> Change 4465b469008bc03b98a1b8df4e9ae501b6c69d4b caused rules
> to stop matching the input device properly because the
> FLOWI_FLAG_MATCH_ANY_IIF is always defined in ip_dev_find().
>
> This breaks rules such as:
>
> ip rule add pref 512 lookup local
> ip rule del pref 0 lookup local
> ip link set eth2 up
> ip -4 addr add 172.16.0.102/24 broadcast 172.16.0.255 dev eth2
> ip rule add to 172.16.0.102 iif eth2 lookup local pref 10
> ip rule add iif eth2 lookup 10001 pref 20
> ip route add 172.16.0.0/24 dev eth2 table 10001
> ip route add unreachable 0/0 table 10001
>
> If you had a second interface 'eth0' that was on a different
> subnet, pinging a system on that interface would fail:
>
> [root@ct503-60 ~]# ping 192.168.100.1
> connect: Invalid argument
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://bugzilla.kernel.org/show_bug.cgi?id=25352
This regression was caused by commit a31437b85: "ext4: use
sb_issue_zeroout in setup_new_group_blocks", by accidentally dropping
the code which reserved the block group descriptor and inode table
blocks.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
Fix build errors like these (from a randconfig and my defconfig for a custom board):
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:549: error: dereferencing pointer to incomplete type: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:636: error: implicit declaration of function 'nonseekable_open': 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:657: error: variable 'mpc52xx_wdt_fops' has initializer but incomplete type: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:658: error: excess elements in struct initializer: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:658: error: unknown field 'owner' specified in initializer: 1 errors in 1 logs
...
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The original code returns 0 on success and 1 on failure. In fact, at
this point, "ret" is already either zero or a negative error code so
we can just return it directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the user-provided len is less than the expected offset, the
IRLMP_ENUMDEVICES getsockopt will do a copy_to_user() with a very large
size value. While this isn't be a security issue on x86 because it will
get caught by the access_ok() check, it may leak large amounts of kernel
heap on other architectures. In any event, this patch fixes it.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexey Vlasov found /proc/net/tcp could sometime loop and display
millions of sockets in LISTEN state.
In 2.6.29, when we converted TCP hash tables to RCU, we left two
sk_next() calls in listening_get_next().
We must instead use sk_nulls_next() to properly detect an end of chain.
Reported-by: Alexey Vlasov <renton@renton.name>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix two related problems in the event-copying loop of
ring_buffer_read_page.
The loop condition for copying events is off-by-one.
"len" is the remaining space in the caller-supplied page.
"size" is the size of the next event (or two events).
If len == size, then there is just enough space for the next event.
size was set to rb_event_ts_length, which may include the size of two
events if the first event is a time-extend, in order to assure time-
extends are kept together with the event after it. However,
rb_advance_reader always advances by one event. This would result in the
event after any time-extend being duplicated. Instead, get the size of
a single event for the memcpy, but use rb_event_ts_length for the loop
condition.
Signed-off-by: David Sharp <dhsharp@google.com>
LKML-Reference: <1293064704-8101-1-git-send-email-dhsharp@google.com>
LKML-Reference: <AANLkTin7nLrRPc9qGjdjHbeVDDWiJjAiYyb-L=gH85bx@mail.gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
|
|
The fix-up entries by the commit 2785591a9760c677a7ee6f541e751c23086f5bfd
ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
weren't applied in the right position. They had to be before the quirk
entry matching to all Sony devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
When a mixer control element was already created with the given name,
try to find another index for avoiding conflicts, instead of breaking
with an error. This makes the driver more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When the d-mics are assigned to the same purpose of another analog mic
pins, the driver doesn't compute the index properly, resulting in an
error with "existing control". This patch fixes it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Include the connector name in the output_poll_execute() debug message
drm/radeon/kms: fix bug in r600_gpu_is_lockup
drm/radeon/kms: reorder display resume to avoid problems
drm/radeon/kms/evergreen: reset the grbm blocks at resume and init
drm/radeon/kms: fix evergreen asic reset
Revert "drm: Don't try and disable an encoder that was never enabled"
drm/radeon: Add early unregister of firmware fb's
drm/radeon: use aperture size not vram size for overlap tests
drm/radeon/kms/evergreen: flush hdp cache when flushing gart tlb
drm/radeon/kms: disable the r600 cb offset checker for linear surfaces
drm/radeon/kms: disable ss fixed ref divide
drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915/ringbuffer: Handle wrapping of the autoreported HEAD
drm/i915/dp: Fix I2C/EDID handling with active DisplayPort to DVI converter
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Support additional parent IDs for wm831x
mfd: Fix ab8500-core interrupt ffs bit bug
mfd: Supply IRQ base for WM832x devices
watchdog: Fix null pointer dereference while accessing rdc321x platform_data
gpio: Fix null pointer dereference while accessing rdc321x platform_data
|
|
This was fixed by David Lamparter in v2.6.36-rc5 3486008 ("spi: free
children in spi_unregister_master, not siblings") and broken again in
v2.6.37-rc1~2^2~4 during the merge of 2b9603a0 ("spi: enable
spi_board_info to be registered after spi_master").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The taskstats structure is internally aligned on 8 byte boundaries but the
layout of the aggregrate reply, with two NLA headers and the pid (each 4
bytes), actually force the entire structure to be unaligned. This causes
the kernel to issue unaligned access warnings on some architectures like
ia64. Unfortunately, some software out there doesn't properly unroll the
NLA packet and assumes that the start of the taskstats structure will
always be 20 bytes from the start of the netlink payload. Aligning the
start of the taskstats structure breaks this software, which we don't
want. So, for now the alignment only happens on architectures that
require it and those users will have to update to fixed versions of those
packages. Space is reserved in the packet only when needed. This ifdef
should be removed in several years e.g. 2012 once we can be confident
that fixed versions are installed on most systems. We add the padding
before the aggregate since the aggregate is already a defined type.
Commit 85893120 ("delayacct: align to 8 byte boundary on 64-bit systems")
previously addressed the alignment issues by padding out the pid field.
This was supposed to be a compatible change but the circumstances
described above mean that it wasn't. This patch backs out that change,
since it was a hack, and introduces a new NULL attribute type to provide
the padding. Padding the response with 4 bytes avoids allocating an
aligned taskstats structure and copying it back. Since the structure
weighs in at 328 bytes, it's too big to do it on the stack.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Brian Rogers <brian@xyzw.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current packed struct implementation of unaligned access adds the
packed attribute only to the field within the unaligned struct rather than
to the struct as a whole. This is not sufficient to enforce proper
behaviour on architectures with a default struct alignment of more than
one byte.
For example, the current implementation of __get_unaligned_cpu16 when
compiled for arm with gcc -O1 -mstructure-size-boundary=32 assumes the
struct is on a 4 byte boundary so performs the load of the 16bit packed
field as if it were on a 4 byte boundary:
__get_unaligned_cpu16:
ldrh r0, [r0, #0]
bx lr
Moving the packed attribute to the struct rather than the field causes the
proper unaligned access code to be generated:
__get_unaligned_cpu16:
ldrb r3, [r0, #0] @ zero_extendqisi2
ldrb r0, [r0, #1] @ zero_extendqisi2
orr r0, r3, r0, asl #8
bx lr
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When I added led_blink_set I had a typo: the return value of the hw
offload is a regular error code that is zero when succesful, and in that
case software emulation should not be used, rather than the other way
around.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Thomas Hellstrom <thomas@tungstengraphics.com>
Cc: Alan Hourihane <alanh@tungstengraphics.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
GCC complained about update_mmu_cache() not being defined in migrate.c.
Including <asm/tlbflush.h> seems to solve the problem.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Match the buffer size to the amount of initialized values. Before, it was
one too big and thus destroyed the neighbouring register causing the clock
to run at false speeds.
Reported-by: Andre van Rooyen <a.v.rooyen@sercom.nl>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove Jordan as the geode maintainer (he's not been interested in geode for
some time), and add myself as the maintainer.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Daniel Drake <dsd@laptop.org>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If GPIO request succeeds, but configuration fails, it should be released.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Using TASK_INTERRUPTIBLE in balance_dirty_pages() seems wrong. If it's
going to do that then it must break out if signal_pending(), otherwise
it's pretty much guaranteed to degenerate into a busywait loop. Plus we
*do* want these processes to appear in D state and to contribute to load
average.
So it should be TASK_UNINTERRUPTIBLE. -- Andrew Morton
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This happens when __logfs_create() tries to write a new inode to the disk
which is full.
__logfs_create() associates the transaction pointer with inode. During
the logfs_write_inode() function call chain this transaction pointer is
moved from inode to page->private using function move_inode_to_page
(do_write_inode() -> inode_to_page() -> move_inode_to_page)
When the write inode fails, the transaction is aborted and iput is called
on the failed inode. During delete_inode the same transaction pointer
associated with the page is getting used. Thus causing kernel BUG.
The patch checks for error in write_inode() and restores the page->private
to NULL.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=20162
Signed-off-by: Prasad Joshi <prasadjoshi124@gmail.com>
Cc: Joern Engel <joern@logfs.org>
Cc: Florian Mickler <florian@mickler.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
do_logfs_journal_wl_pass() should use GFP_NOFS for memory allocation GC
code calls btree_insert32 with GFP_KERNEL while holding a mutex
super->s_write_mutex.
The same mutex is used in address_space_operations->writepage(), and a
call to writepage() could be triggered as a result of memory allocation
in btree_insert32, causing a deadlock.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=20342
Signed-off-by: Prasad Joshi <prasadjoshi124@gmail.com>
Cc: Joern Engel <joern@logfs.org>
Cc: Florian Mickler <florian@mickler.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
and vmstat
When correlating ftrace results with /proc/vmstat, I noticed that the
reporting scripts value for "pages scanned" differed significantly. Both
values were "right" depending on how you look at it.
The difference is due to vmstat only counting scanning of the inactive
list towards pages scanned. The analysis script for the tracepoint counts
active and inactive list yielding a far higher value than vmstat. The
resulting scanning/reclaim ratio looks much worse. The tracepoint is ok
but this patch updates the reporting script so that the report values for
scanned are similar to vmstat.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
del_page_from_lru_list() already called mem_cgroup_del_lru(). So we must
not call it again. It adds unnecessary overhead.
It was not a runtime bug because the TestClearPageCgroupAcctLRU() early in
mem_cgroup_del_lru_list() will prevent any double-deletion, etc.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
The atl1c driver uses the legacy PCI power management, so it has to
do some PCI-specific things in its ->suspend() and ->resume()
callbacks and they are not done correctly.
Convert atl1c to the new PCI power management framework and make it
let the PCI subsystem handle all of the PCI-specific aspects of
device handling during system power transitions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under memory pressure, the mac80211 mesh code
may helpfully print a message that it failed
to clone a mesh frame and then will proceed
to crash trying to use it anyway. Fix that.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Now that percpu allocator is mostly stable, there is no reason to
print alloc information with KERN_INFO and clutter the boot messages.
Switch it to KERN_DEBUG.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
|
|
Some newer device revisions add a second parent ID. Support this in
the device validity checks done at startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
We want to find the first set bit on value, not status.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Without this the IRQ base will not be correctly configured for the
subdevices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
rdc321x-wdt currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When we store system inodes cache in ocfs2_super,
we use a array for global system inodes. But unfortunately,
the range is calculated wrongly which makes it overflow and
pollute ocfs2_super->local_system_inodes.
This patch fix it by setting the range properly.
The corresponding bug is ossbug1303.
http://oss.oracle.com/bugzilla/show_bug.cgi?id=1303
Cc: stable@kernel.org
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux-2.6 into perf/urgent
|
|
spinlock in kthread_worker and wait_queue_head in kthread_work both
should be lockdep sensible, so change the interface to make it
suiltable for CONFIG_LOCKDEP.
tj: comment update
Reported-by: Nicolas <nicolas.mailhot@laposte.net>
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Monitor EDID contains information about physical display sizes. Retrieve
it and propagate to the framebuffer driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
An earlier patch replaced open-coded video-mode configuration from
platform data by a call to fb_videomode_to_var(), thereby setting
ofdisplay sizes have been accidentally lost. Restore them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
My ISP has changed and therefore my email address.
Signed-off-by: Don Fry <pcnet32@frontier.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Always useful to know just which connector was polled and had its
status updated.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We were using the lockup struct from the wrong union.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Since the libdwfl library before 0.148 fails to analyze live kernel debuginfo,
'perf probe --list' compiled with those old libdwfl sometimes crashes.
To avoid that bug, perf probe does not use libdwfl's live kernel analysis
routine when it is compiled with older libdwfl.
Side effect: perf with older libdwfl doesn't support listing probe in modules
with source code line. Those could be shown by symbol+offset.
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20101217131218.24123.62424.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix lazy wildcard matching to ignore space after wild card.
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20101217131200.24123.8202.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
