5 files changed, 16 insertions, 25 deletions
diff --git a/arch/arm/mach-imx/clk-imx35.c b/arch/arm/mach-imx/clk-imx35.c
index 74e3a34d78b..e13a8fa5e62 100644
--- a/arch/arm/mach-imx/clk-imx35.c
+++ b/arch/arm/mach-imx/clk-imx35.c
@@ -264,6 +264,7 @@ int __init mx35_clocks_init(void)
 	clk_prepare_enable(clk[gpio3_gate]);
 	clk_prepare_enable(clk[iim_gate]);
 	clk_prepare_enable(clk[emi_gate]);
+	clk_prepare_enable(clk[max_gate]);
 
 	/*
 	 * SCC is needed to boot via mmc after a watchdog reset. The clock code
diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c
index 7b025ee528a..2f9ff93a4e6 100644
--- a/arch/arm/mach-imx/clk-imx6q.c
+++ b/arch/arm/mach-imx/clk-imx6q.c
@@ -172,7 +172,7 @@ static struct clk *clk[clk_max];
 static struct clk_onecell_data clk_data;
 
 static enum mx6q_clks const clks_init_on[] __initconst = {
-	mmdc_ch0_axi, rom,
+	mmdc_ch0_axi, rom, pll1_sys,
 };
 
 static struct clk_div_table clk_enet_ref_table[] = {
diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S
index 921fc155585..a58c8b0527c 100644
--- a/arch/arm/mach-imx/headsmp.S
+++ b/arch/arm/mach-imx/headsmp.S
@@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup)
 
 #ifdef CONFIG_PM
 /*
- * The following code is located into the .data section.  This is to
- * allow phys_l2x0_saved_regs to be accessed with a relative load
- * as we are running on physical address here.
+ * The following code must assume it is running from physical address
+ * where absolute virtual addresses to the data section have to be
+ * turned into relative ones.
  */
-	.data
-	.align
 
 #ifdef CONFIG_CACHE_L2X0
 	.macro	pl310_resume
-	ldr	r2, phys_l2x0_saved_regs
+	adr	r0, l2x0_saved_regs_offset
+	ldr	r2, [r0]
+	add	r2, r2, r0
 	ldr	r0, [r2, #L2X0_R_PHY_BASE]	@ get physical base of l2x0
 	ldr	r1, [r2, #L2X0_R_AUX_CTRL]	@ get aux_ctrl value
 	str	r1, [r0, #L2X0_AUX_CTRL]	@ restore aux_ctrl
@@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup)
 	str	r1, [r0, #L2X0_CTRL]		@ re-enable L2
 	.endm
 
-	.globl	phys_l2x0_saved_regs
-phys_l2x0_saved_regs:
-        .long   0
+l2x0_saved_regs_offset:
+	.word	l2x0_saved_regs - .
+
 #else
 	.macro	pl310_resume
 	.endm
diff --git a/arch/arm/mach-imx/imx25-dt.c b/arch/arm/mach-imx/imx25-dt.c
index 03b65e5ea54..82348391582 100644
--- a/arch/arm/mach-imx/imx25-dt.c
+++ b/arch/arm/mach-imx/imx25-dt.c
@@ -27,6 +27,11 @@ static const char * const imx25_dt_board_compat[] __initconst = {
 	NULL
 };
 
+static void __init imx25_timer_init(void)
+{
+	mx25_clocks_init_dt();
+}
+
 DT_MACHINE_START(IMX25_DT, "Freescale i.MX25 (Device Tree Support)")
 	.map_io		= mx25_map_io,
 	.init_early	= imx25_init_early,
diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
index ee42d20cba1..5faba7a3c95 100644
--- a/arch/arm/mach-imx/pm-imx6q.c
+++ b/arch/arm/mach-imx/pm-imx6q.c
@@ -22,8 +22,6 @@
 #include "common.h"
 #include "hardware.h"
 
-extern unsigned long phys_l2x0_saved_regs;
-
 static int imx6q_suspend_finish(unsigned long val)
 {
 	cpu_do_idle();
@@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = {
 
 void __init imx6q_pm_init(void)
 {
-	/*
-	 * The l2x0 core code provides an infrastucture to save and restore
-	 * l2x0 registers across suspend/resume cycle.  But because imx6q
-	 * retains L2 content during suspend and needs to resume L2 before
-	 * MMU is enabled, it can only utilize register saving support and
-	 * have to take care of restoring on its own.  So we save physical
-	 * address of the data structure used by l2x0 core to save registers,
-	 * and later restore the necessary ones in imx6q resume entry.
-	 */
-#ifdef CONFIG_CACHE_L2X0
-	phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
-#endif
-
 	suspend_set_ops(&imx6q_pm_ops);
 }