summaryrefslogtreecommitdiff
path: root/Documentation/powerpc
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/powerpc')
-rw-r--r--Documentation/powerpc/booting-without-of.txt142
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/pmc.txt63
2 files changed, 163 insertions, 42 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index de2e5c05d6e..07ae2edff7c 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -77,10 +77,12 @@ Table of Contents
3) OpenPIC Interrupt Controllers
4) ISA Interrupt Controllers
- VIII - Specifying GPIO information for devices
+ IX - Specifying GPIO information for devices
1) gpios property
2) gpio-controller nodes
+ X - Specifying device power management information (sleep property)
+
Appendix A - Sample SOC node for MPC8540
@@ -2422,8 +2424,8 @@ encodings listed below:
2 = high to low edge sensitive type enabled
3 = low to high edge sensitive type enabled
-VIII - Specifying GPIO information for devices
-==============================================
+IX - Specifying GPIO information for devices
+============================================
1) gpios property
-----------------
@@ -2471,6 +2473,37 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
gpio-controller;
};
+X - Specifying Device Power Management Information (sleep property)
+===================================================================
+
+Devices on SOCs often have mechanisms for placing devices into low-power
+states that are decoupled from the devices' own register blocks. Sometimes,
+this information is more complicated than a cell-index property can
+reasonably describe. Thus, each device controlled in such a manner
+may contain a "sleep" property which describes these connections.
+
+The sleep property consists of one or more sleep resources, each of
+which consists of a phandle to a sleep controller, followed by a
+controller-specific sleep specifier of zero or more cells.
+
+The semantics of what type of low power modes are possible are defined
+by the sleep controller. Some examples of the types of low power modes
+that may be supported are:
+
+ - Dynamic: The device may be disabled or enabled at any time.
+ - System Suspend: The device may request to be disabled or remain
+ awake during system suspend, but will not be disabled until then.
+ - Permanent: The device is disabled permanently (until the next hard
+ reset).
+
+Some devices may share a clock domain with each other, such that they should
+only be suspended when none of the devices are in use. Where reasonable,
+such nodes should be placed on a virtual bus, where the bus has the sleep
+property. If the clock domain is shared among devices that cannot be
+reasonably grouped in this manner, then create a virtual sleep controller
+(similar to an interrupt nexus, except that defining a standardized
+sleep-map should wait until its necessity is demonstrated).
+
Appendix A - Sample SOC node for MPC8540
========================================
@@ -2487,47 +2520,48 @@ not necessary as they are usually the same as the root node.
reg = <e0000000 00003000>;
bus-frequency = <0>;
- mdio@24520 {
- reg = <24520 20>;
- device_type = "mdio";
- compatible = "gianfar";
-
- ethernet-phy@0 {
- linux,phandle = <2452000>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <0>;
- device_type = "ethernet-phy";
- };
-
- ethernet-phy@1 {
- linux,phandle = <2452001>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
-
- ethernet-phy@3 {
- linux,phandle = <2452002>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
-
- };
-
ethernet@24000 {
- #size-cells = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
device_type = "network";
model = "TSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <24000 1000>;
mac-address = [ 00 E0 0C 00 73 00 ];
interrupts = <d 3 e 3 12 3>;
interrupt-parent = <40000>;
phy-handle = <2452000>;
+ sleep = <&pmc 00000080>;
+ ranges;
+
+ mdio@24520 {
+ reg = <24520 20>;
+ compatible = "fsl,gianfar-mdio";
+
+ ethernet-phy@0 {
+ linux,phandle = <2452000>
+ interrupt-parent = <40000>;
+ interrupts = <35 1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ ethernet-phy@1 {
+ linux,phandle = <2452001>
+ interrupt-parent = <40000>;
+ interrupts = <35 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+
+ ethernet-phy@3 {
+ linux,phandle = <2452002>
+ interrupt-parent = <40000>;
+ interrupts = <35 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
};
ethernet@25000 {
@@ -2541,6 +2575,7 @@ not necessary as they are usually the same as the root node.
interrupts = <13 3 14 3 18 3>;
interrupt-parent = <40000>;
phy-handle = <2452001>;
+ sleep = <&pmc 00000040>;
};
ethernet@26000 {
@@ -2554,15 +2589,33 @@ not necessary as they are usually the same as the root node.
interrupts = <19 3>;
interrupt-parent = <40000>;
phy-handle = <2452002>;
+ sleep = <&pmc 00000020>;
};
serial@4500 {
- device_type = "serial";
- compatible = "ns16550";
- reg = <4500 100>;
- clock-frequency = <0>;
- interrupts = <1a 3>;
- interrupt-parent = <40000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8540-duart", "simple-bus";
+ sleep = <&pmc 00000002>;
+ ranges;
+
+ serial@4500 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <4500 100>;
+ clock-frequency = <0>;
+ interrupts = <1a 3>;
+ interrupt-parent = <40000>;
+ };
+
+ serial@4600 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <4600 100>;
+ clock-frequency = <0>;
+ interrupts = <1a 3>;
+ interrupt-parent = <40000>;
+ };
};
pic@40000 {
@@ -2581,6 +2634,11 @@ not necessary as they are usually the same as the root node.
device_type = "i2c";
compatible = "fsl-i2c";
dfsrr;
+ sleep = <&pmc 00000004>;
};
+ pmc: power@e0070 {
+ compatible = "fsl,mpc8540-pmc", "fsl,mpc8548-pmc";
+ reg = <e0070 20>;
+ };
};
diff --git a/Documentation/powerpc/dts-bindings/fsl/pmc.txt b/Documentation/powerpc/dts-bindings/fsl/pmc.txt
new file mode 100644
index 00000000000..02f6f43ee1b
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/pmc.txt
@@ -0,0 +1,63 @@
+* Power Management Controller
+
+Properties:
+- compatible: "fsl,<chip>-pmc".
+
+ "fsl,mpc8349-pmc" should be listed for any chip whose PMC is
+ compatible. "fsl,mpc8313-pmc" should also be listed for any chip
+ whose PMC is compatible, and implies deep-sleep capability.
+
+ "fsl,mpc8548-pmc" should be listed for any chip whose PMC is
+ compatible. "fsl,mpc8536-pmc" should also be listed for any chip
+ whose PMC is compatible, and implies deep-sleep capability.
+
+ "fsl,mpc8641d-pmc" should be listed for any chip whose PMC is
+ compatible; all statements below that apply to "fsl,mpc8548-pmc" also
+ apply to "fsl,mpc8641d-pmc".
+
+ Compatibility does not include bit assigments in SCCR/PMCDR/DEVDISR; these
+ bit assigments are indicated via the sleep specifier in each device's
+ sleep property.
+
+- reg: For devices compatible with "fsl,mpc8349-pmc", the first resource
+ is the PMC block, and the second resource is the Clock Configuration
+ block.
+
+ For devices compatible with "fsl,mpc8548-pmc", the first resource
+ is a 32-byte block beginning with DEVDISR.
+
+- interrupts: For "fsl,mpc8349-pmc"-compatible devices, the first
+ resource is the PMC block interrupt.
+
+- fsl,mpc8313-wakeup-timer: For "fsl,mpc8313-pmc"-compatible devices,
+ this is a phandle to an "fsl,gtm" node on which timer 4 can be used as
+ a wakeup source from deep sleep.
+
+Sleep specifiers:
+
+ fsl,mpc8349-pmc: Sleep specifiers consist of one cell. For each bit
+ that is set in the cell, the corresponding bit in SCCR will be saved
+ and cleared on suspend, and restored on resume. This sleep controller
+ supports disabling and resuming devices at any time.
+
+ fsl,mpc8536-pmc: Sleep specifiers consist of three cells, the third of
+ which will be ORed into PMCDR upon suspend, and cleared from PMCDR
+ upon resume. The first two cells are as described for fsl,mpc8578-pmc.
+ This sleep controller only supports disabling devices during system
+ sleep, or permanently.
+
+ fsl,mpc8548-pmc: Sleep specifiers consist of one or two cells, the
+ first of which will be ORed into DEVDISR (and the second into
+ DEVDISR2, if present -- this cell should be zero or absent if the
+ hardware does not have DEVDISR2) upon a request for permanent device
+ disabling. This sleep controller does not support configuring devices
+ to disable during system sleep (unless supported by another compatible
+ match), or dynamically.
+
+Example:
+
+ power@b00 {
+ compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 8>;
+ };