diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
146 files changed, 3738 insertions, 174 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt new file mode 100644 index 00000000000..ecdb57d69db --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt @@ -0,0 +1,11 @@ +Altera SOCFPGA Reset Manager + +Required properties: +- compatible : "altr,rst-mgr" +- reg : Should contain 1 register ranges(address and length) + +Example: + rstmgr@ffd05000 { + compatible = "altr,rst-mgr"; + reg = <0xffd05000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt new file mode 100644 index 00000000000..07c65e3cdcb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt @@ -0,0 +1,11 @@ +Altera SOCFPGA System Manager + +Required properties: +- compatible : "altr,sys-mgr" +- reg : Should contain 1 register ranges(address and length) + +Example: + sysmgr@ffd08000 { + compatible = "altr,sys-mgr"; + reg = <0xffd08000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index fc81a7d6b0f..db5858e32d3 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -9,6 +9,10 @@ Required properties (in root node): FPGA type interrupt controllers, see the versatile-fpga-irq binding doc. +In the root node the Integrator/CP must have a /cpcon node pointing +to the CP control registers, and the Integrator/AP must have a +/syscon node pointing to the Integrator/AP system controller. + ARM Versatile Application and Platform Baseboards ------------------------------------------------- diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt index 70c0dc5f00e..61df564c0d2 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt @@ -6,9 +6,15 @@ Required properties: - interrupt-controller: Identifies the node as an interrupt controller. - #interrupt-cells: The number of cells to define the interrupts. Should be 1. The cell is the IRQ number + - reg: Should contain PMIC registers location and length. First pair for the main interrupt registers, second pair for the per-CPU - interrupt registers + interrupt registers. For this last pair, to be compliant with SMP + support, the "virtual" must be use (For the record, these registers + automatically map to the interrupt controller registers of the + current CPU) + + Example: @@ -18,6 +24,6 @@ Example: #address-cells = <1>; #size-cells = <1>; interrupt-controller; - reg = <0xd0020000 0x1000>, - <0xd0021000 0x1000>; + reg = <0xd0020a00 0x1d0>, + <0xd0021070 0x58>; }; diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt new file mode 100644 index 00000000000..926b4d6aae7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt @@ -0,0 +1,20 @@ +Power Management Service Unit(PMSU) +----------------------------------- +Available on Marvell SOCs: Armada 370 and Armada XP + +Required properties: + +- compatible: "marvell,armada-370-xp-pmsu" + +- reg: Should contain PMSU registers location and length. First pair + for the per-CPU SW Reset Control registers, second pair for the + Power Management Service Unit. + +Example: + +armada-370-xp-pmsu@d0022000 { + compatible = "marvell,armada-370-xp-pmsu"; + reg = <0xd0022100 0x430>, + <0xd0020800 0x20>; +}; + diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt index 8b6ea2267c9..64830118b01 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt @@ -5,6 +5,7 @@ Required properties: - compatible: Should be "marvell,armada-370-xp-timer" - interrupts: Should contain the list of Global Timer interrupts - reg: Should contain the base address of the Global Timer registers +- clocks: clock driving the timer hardware Optional properties: - marvell,timer-25Mhz: Tells whether the Global timer supports the 25 diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index d187e9f7cf1..1196290082d 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -7,6 +7,12 @@ PIT Timer required properties: - interrupts: Should contain interrupt for the PIT which is the IRQ line shared across all System Controller members. +System Timer (ST) required properties: +- compatible: Should be "atmel,at91rm9200-st" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt for the ST which is the IRQ line + shared across all System Controller members. + TC/TCLIB Timer required properties: - compatible: Should be "atmel,<chip>-tcb". <chip> can be "at91rm9200" or "at91sam9x5" diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt b/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt new file mode 100644 index 00000000000..fb7b5cd2652 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt @@ -0,0 +1,9 @@ +Broadcom BCM11351 device tree bindings +------------------------------------------- + +Boards with the bcm281xx SoC family (which includes bcm11130, bcm11140, +bcm11351, bcm28145, bcm28155 SoCs) shall have the following properties: + +Required root node property: + +compatible = "bcm,bcm11351"; diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt index 4755caaccba..25fcf96795c 100644 --- a/Documentation/devicetree/bindings/arm/calxeda.txt +++ b/Documentation/devicetree/bindings/arm/calxeda.txt @@ -1,8 +1,15 @@ -Calxeda Highbank Platforms Device Tree Bindings +Calxeda Platforms Device Tree Bindings ----------------------------------------------- -Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following -properties. +Boards with Calxeda Cortex-A9 based ECX-1000 (Highbank) SOC shall have the +following properties. Required root node properties: - compatible = "calxeda,highbank"; + + +Boards with Calxeda Cortex-A15 based ECX-2000 SOC shall have the following +properties. + +Required root node properties: + - compatible = "calxeda,ecx-2000"; diff --git a/Documentation/devicetree/bindings/arm/coherency-fabric.txt b/Documentation/devicetree/bindings/arm/coherency-fabric.txt new file mode 100644 index 00000000000..17d8cd10755 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/coherency-fabric.txt @@ -0,0 +1,21 @@ +Coherency fabric +---------------- +Available on Marvell SOCs: Armada 370 and Armada XP + +Required properties: + +- compatible: "marvell,coherency-fabric" + +- reg: Should contain coherency fabric registers location and + length. First pair for the coherency fabric registers, second pair + for the per-CPU fabric registers registers. + +Example: + +coherency-fabric@d0020200 { + compatible = "marvell,coherency-fabric"; + reg = <0xd0020200 0xb0>, + <0xd0021810 0x1c>; + +}; + diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt new file mode 100644 index 00000000000..f32494dbfe1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -0,0 +1,77 @@ +* ARM CPUs binding description + +The device tree allows to describe the layout of CPUs in a system through +the "cpus" node, which in turn contains a number of subnodes (ie "cpu") +defining properties for every cpu. + +Bindings for CPU nodes follow the ePAPR standard, available from: + +http://devicetree.org + +For the ARM architecture every CPU node must contain the following properties: + +- device_type: must be "cpu" +- reg: property matching the CPU MPIDR[23:0] register bits + reg[31:24] bits must be set to 0 +- compatible: should be one of: + "arm,arm1020" + "arm,arm1020e" + "arm,arm1022" + "arm,arm1026" + "arm,arm720" + "arm,arm740" + "arm,arm7tdmi" + "arm,arm920" + "arm,arm922" + "arm,arm925" + "arm,arm926" + "arm,arm940" + "arm,arm946" + "arm,arm9tdmi" + "arm,cortex-a5" + "arm,cortex-a7" + "arm,cortex-a8" + "arm,cortex-a9" + "arm,cortex-a15" + "arm,arm1136" + "arm,arm1156" + "arm,arm1176" + "arm,arm11mpcore" + "faraday,fa526" + "intel,sa110" + "intel,sa1100" + "marvell,feroceon" + "marvell,mohawk" + "marvell,xsc3" + "marvell,xscale" + +Example: + + cpus { + #size-cells = <0>; + #address-cells = <1>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x1>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/davinci.txt b/Documentation/devicetree/bindings/arm/davinci.txt new file mode 100644 index 00000000000..cfaeda4274e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/davinci.txt @@ -0,0 +1,17 @@ +Texas Instruments DaVinci Platforms Device Tree Bindings +-------------------------------------------------------- + +DA850/OMAP-L138/AM18x Evaluation Module (EVM) board +Required root node properties: + - compatible = "ti,da850-evm", "ti,da850"; + +EnBW AM1808 based CMC board +Required root node properties: + - compatible = "enbw,cmc", "ti,da850; + +Generic DaVinci Boards +---------------------- + +DA850/OMAP-L138/AM18x generic board +Required root node properties: + - compatible = "ti,da850"; diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt index e37241f1fdd..3545ea704b5 100644 --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -23,29 +23,24 @@ Recommended properties : - ti,davinci-nand-buswidth: buswidth 8 or 16 - ti,davinci-nand-use-bbt: use flash based bad block table support. -Example (enbw_cmc board): -aemif@60000000 { - compatible = "ti,davinci-aemif"; - #address-cells = <2>; - #size-cells = <1>; - reg = <0x68000000 0x80000>; - ranges = <2 0 0x60000000 0x02000000 - 3 0 0x62000000 0x02000000 - 4 0 0x64000000 0x02000000 - 5 0 0x66000000 0x02000000 - 6 0 0x68000000 0x02000000>; - nand@3,0 { - compatible = "ti,davinci-nand"; - reg = <3 0x0 0x807ff - 6 0x0 0x8000>; - #address-cells = <1>; - #size-cells = <1>; - ti,davinci-chipselect = <1>; - ti,davinci-mask-ale = <0>; - ti,davinci-mask-cle = <0>; - ti,davinci-mask-chipsel = <0>; - ti,davinci-ecc-mode = "hw"; - ti,davinci-ecc-bits = <4>; - ti,davinci-nand-use-bbt; +nand device bindings may contain additional sub-nodes describing +partitions of the address space. See partition.txt for more detail. + +Example(da850 EVM ): +nand_cs3@62000000 { + compatible = "ti,davinci-nand"; + reg = <0x62000000 0x807ff + 0x68000000 0x8000>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + ti,davinci-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + ti,davinci-nand-use-bbt; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x7e80000>; }; }; diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 6528e215c5f..5216b419016 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -4,14 +4,13 @@ Exynos processors include support for multiple power domains which are used to gate power to one or more peripherals on the processor. Required Properties: -- compatiable: should be one of the following. +- compatible: should be one of the following. * samsung,exynos4210-pd - for exynos4210 type power domain. - reg: physical base address of the controller and length of memory mapped region. -Optional Properties: -- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off - state during boot and remains to be turned-off until explicitly turned-on. +Node of a device using power domains must have a samsung,power-domain property +defined with a phandle to respective power domain. Example: @@ -19,3 +18,11 @@ Example: compatible = "samsung,exynos4210-pd"; reg = <0x10023C00 0x10>; }; + +Example of the node using power domain: + + node { + /* ... */ + samsung,power-domain = <&lcd0>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index ac9e7516756..f79818711e8 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -41,6 +41,10 @@ i.MX6 Quad SABRE Smart Device Board Required root node properties: - compatible = "fsl,imx6q-sabresd", "fsl,imx6q"; +i.MX6 Quad SABRE Automotive Board +Required root node properties: + - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q"; + Generic i.MX boards ------------------- diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index 7ca52161e7a..cbef09b5c8a 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -10,6 +10,12 @@ Required properties: "arm,pl310-cache" "arm,l220-cache" "arm,l210-cache" + "marvell,aurora-system-cache": Marvell Controller designed to be + compatible with the ARM one, with system cache mode (meaning + maintenance operations on L1 are broadcasted to the L2 and L2 + performs the same operation). + "marvell,"aurora-outer-cache: Marvell Controller designed to be + compatible with the ARM one with outer cache mode. - cache-unified : Specifies the cache is a unified cache. - cache-level : Should be set to 2 for a level 2 cache. - reg : Physical base address and size of cache controller's memory mapped @@ -29,6 +35,9 @@ Optional properties: filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. - interrupts : 1 combined interrupt. +- cache-id-part: cache id part number to be used if it is not present + on hardware +- wt-override: If present then L2 is forced to Write through mode Example: @@ -37,7 +46,7 @@ L2: cache-controller { reg = <0xfff12000 0x1000>; arm,data-latency = <1 1 1>; arm,tag-latency = <2 2 2>; - arm,filter-latency = <0x80000000 0x8000000>; + arm,filter-ranges = <0x80000000 0x8000000>; cache-unified; cache-level = <2>; interrupts = <45>; diff --git a/Documentation/devicetree/bindings/arm/omap/counter.txt b/Documentation/devicetree/bindings/arm/omap/counter.txt new file mode 100644 index 00000000000..5bd8aa09131 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/counter.txt @@ -0,0 +1,15 @@ +OMAP Counter-32K bindings + +Required properties: +- compatible: Must be "ti,omap-counter32k" for OMAP controllers +- reg: Contains timer register address range (base address and length) +- ti,hwmods: Name of the hwmod associated to the counter, which is typically + "counter_32k" + +Example: + +counter32k: counter@4a304000 { + compatible = "ti,omap-counter32k"; + reg = <0x4a304000 0x20>; + ti,hwmods = "counter_32k"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/timer.txt b/Documentation/devicetree/bindings/arm/omap/timer.txt new file mode 100644 index 00000000000..8732d4d41f8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/timer.txt @@ -0,0 +1,31 @@ +OMAP Timer bindings + +Required properties: +- compatible: Must be "ti,omap2-timer" for OMAP2+ controllers. +- reg: Contains timer register address range (base address and + length). +- interrupts: Contains the interrupt information for the timer. The + format is being dependent on which interrupt controller + the OMAP device uses. +- ti,hwmods: Name of the hwmod associated to the timer, "timer<X>", + where <X> is the instance number of the timer from the + HW spec. + +Optional properties: +- ti,timer-alwon: Indicates the timer is in an alway-on power domain. +- ti,timer-dsp: Indicates the timer can interrupt the on-chip DSP in + addition to the ARM CPU. +- ti,timer-pwm: Indicates the timer can generate a PWM output. +- ti,timer-secure: Indicates the timer is reserved on a secure OMAP device + and therefore cannot be used by the kernel. + +Example: + +timer12: timer@48304000 { + compatible = "ti,omap2-timer"; + reg = <0x48304000 0x400>; + interrupts = <95>; + ti,hwmods = "timer12" + ti,timer-alwon; + ti,timer-secure; +}; diff --git a/Documentation/devicetree/bindings/arm/spear/shirq.txt b/Documentation/devicetree/bindings/arm/spear/shirq.txt new file mode 100644 index 00000000000..13fbb8866bd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear/shirq.txt @@ -0,0 +1,48 @@ +* SPEAr Shared IRQ layer (shirq) + +SPEAr3xx architecture includes shared/multiplexed irqs for certain set +of devices. The multiplexor provides a single interrupt to parent +interrupt controller (VIC) on behalf of a group of devices. + +There can be multiple groups available on SPEAr3xx variants but not +exceeding 4. The number of devices in a group can differ, further they +may share same set of status/mask registers spanning across different +bit masks. Also in some cases the group may not have enable or other +registers. This makes software little complex. + +A single node in the device tree is used to describe the shared +interrupt multiplexor (one node for all groups). A group in the +interrupt controller shares config/control registers with other groups. +For example, a 32-bit interrupt enable/disable config register can +accommodate upto 4 interrupt groups. + +Required properties: + - compatible: should be, either of + - "st,spear300-shirq" + - "st,spear310-shirq" + - "st,spear320-shirq" + - interrupt-controller: Identifies the node as an interrupt controller. + - #interrupt-cells: should be <1> which basically contains the offset + (starting from 0) of interrupts for all the groups. + - reg: Base address and size of shirq registers. + - interrupts: The list of interrupts generated by the groups which are + then connected to a parent interrupt controller. Each group is + associated with one of the interrupts, hence number of interrupts (to + parent) is equal to number of groups. The format of the interrupt + specifier depends in the interrupt parent controller. + + Optional properties: + - interrupt-parent: pHandle of the parent interrupt controller, if not + inherited from the parent node. + +Example: + +The following is an example from the SPEAr320 SoC dtsi file. + +shirq: interrupt-controller@0xb3000000 { + compatible = "st,spear320-shirq"; + reg = <0xb3000000 0x1000>; + interrupts = <28 29 30 1>; + #interrupt-cells = <1>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt new file mode 100644 index 00000000000..9cf3f25544c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt @@ -0,0 +1,50 @@ +ARM Versatile Express system registers +-------------------------------------- + +This is a system control registers block, providing multiple low level +platform functions like board detection and identification, software +interrupt generation, MMC and NOR Flash control etc. + +Required node properties: +- compatible value : = "arm,vexpress,sysreg"; +- reg : physical base address and the size of the registers window +- gpio-controller : specifies that the node is a GPIO controller +- #gpio-cells : size of the GPIO specifier, should be 2: + - first cell is the pseudo-GPIO line number: + 0 - MMC CARDIN + 1 - MMC WPROT + 2 - NOR FLASH WPn + - second cell can take standard GPIO flags (currently ignored). + +Example: + v2m_sysreg: sysreg@10000000 { + compatible = "arm,vexpress-sysreg"; + reg = <0x10000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + }; + +This block also can also act a bridge to the platform's configuration +bus via "system control" interface, addressing devices with site number, +position in the board stack, config controller, function and device +numbers - see motherboard's TRM for more details. + +The node describing a config device must refer to the sysreg node via +"arm,vexpress,config-bridge" phandle (can be also defined in the node's +parent) and relies on the board topology properties - see main vexpress +node documentation for more details. It must must also define the +following property: +- arm,vexpress-sysreg,func : must contain two cells: + - first cell defines function number (eg. 1 for clock generator, + 2 for voltage regulators etc.) + - device number (eg. osc 0, osc 1 etc.) + +Example: + mcc { + arm,vexpress,config-bridge = <&v2m_sysreg>; + + osc@0 { + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 0>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt index ec8b50cbb2e..ae49161e478 100644 --- a/Documentation/devicetree/bindings/arm/vexpress.txt +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -11,6 +11,10 @@ the motherboard file using a /include/ directive. As the motherboard can be initialized in one of two different configurations ("memory maps"), care must be taken to include the correct one. + +Root node +--------- + Required properties in the root node: - compatible value: compatible = "arm,vexpress,<model>", "arm,vexpress"; @@ -45,6 +49,10 @@ Optional properties in the root node: - Coretile Express A9x4 (V2P-CA9) HBI-0225: arm,hbi = <0x225>; + +CPU nodes +--------- + Top-level standard "cpus" node is required. It must contain a node with device_type = "cpu" property for every available core, eg.: @@ -59,6 +67,52 @@ with device_type = "cpu" property for every available core, eg.: }; }; + +Configuration infrastructure +---------------------------- + +The platform has an elaborated configuration system, consisting of +microcontrollers residing on the mother- and daughterboards known +as Motherboard/Daughterboard Configuration Controller (MCC and DCC). +The controllers are responsible for the platform initialization +(reset generation, flash programming, FPGA bitfiles loading etc.) +but also control clock generators, voltage regulators, gather +environmental data like temperature, power consumption etc. Even +the video output switch (FPGA) is controlled that way. + +Nodes describing devices controlled by this infrastructure should +point at the bridge device node: +- bridge phandle: + arm,vexpress,config-bridge = <phandle>; +This property can be also defined in a parent node (eg. for a DCC) +and is effective for all children. + + +Platform topology +----------------- + +As Versatile Express can be configured in number of physically +different setups, the device tree should describe platform topology. +Root node and main motherboard node must define the following +property, describing physical location of the children nodes: +- site number: + arm,vexpress,site = <number>; + where 0 means motherboard, 1 or 2 are daugtherboard sites, + 0xf means "master" site (site containing main CPU tile) +- when daughterboards are stacked on one site, their position + in the stack be be described with: + arm,vexpress,position = <number>; +- when describing tiles consisting more than one DCC, its number + can be described with: + arm,vexpress,dcc = <number>; + +Any of the numbers above defaults to zero if not defined in +the node or any of its parent. + + +Motherboard +----------- + The motherboard description file provides a single "motherboard" node using 2 address cells corresponding to the Static Memory Bus used between the motherboard and the tile. The first cell defines the Chip @@ -87,22 +141,30 @@ can be used to obtain required phandle in the tile's "aliases" node: - SP804 timers: v2m_timer01 and v2m_timer23 -Current Linux implementation requires a "arm,v2m_timer" alias -pointing at one of the motherboard's SP804 timers, if it is to be -used as the system timer. This alias should be defined in the -motherboard files. +The tile description should define a "smb" node, describing the +Static Memory Bus between the tile and motherboard. It must define +the following properties: +- "simple-bus" compatible value (to ensure creation of the children) + compatible = "simple-bus"; +- mapping of the SMB CS/offset addresses into main address space: + #address-cells = <2>; + #size-cells = <1>; + ranges = <...>; +- interrupts mapping: + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 63>; + interrupt-map = <...>; -The tile description must define "ranges", "interrupt-map-mask" and -"interrupt-map" properties to translate the motherboard's address -and interrupt space into one used by the tile's processor. -Abbreviated example: +Example of a VE tile description (simplified) +--------------------------------------------- /dts-v1/; / { model = "V2P-CA5s"; arm,hbi = <0x225>; + arm,vexpress,site = <0xf>; compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress"; interrupt-parent = <&gic>; #address-cells = <1>; @@ -134,13 +196,29 @@ Abbreviated example: <0x2c000100 0x100>; }; - motherboard { + dcc { + compatible = "simple-bus"; + arm,vexpress,config-bridge = <&v2m_sysreg>; + + osc@0 { + compatible = "arm,vexpress-osc"; + }; + }; + + smb { + compatible = "simple-bus"; + + #address-cells = <2>; + #size-cells = <1>; /* CS0 is visible at 0x08000000 */ ranges = <0 0 0x08000000 0x04000000>; + + #interrupt-cells = <1>; interrupt-map-mask = <0 0 63>; /* Active high IRQ 0 is connected to GIC's SPI0 */ interrupt-map = <0 0 0 &gic 0 0 4>; + + /include/ "vexpress-v2m-rs1.dtsi" }; }; -/include/ "vexpress-v2m-rs1.dtsi" diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt new file mode 100644 index 00000000000..37824fac688 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt @@ -0,0 +1,14 @@ +* Samsung SATA PHY Controller + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible : compatible list, contains "samsung,exynos5-sata-phy" +- reg : <registers mapping> + +Example: + sata@ffe07000 { + compatible = "samsung,exynos5-sata-phy"; + reg = <0xffe07000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt new file mode 100644 index 00000000000..0849f1025e3 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt @@ -0,0 +1,17 @@ +* Samsung AHCI SATA Controller + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA controller should have its own node. + +Required properties: +- compatible : compatible list, contains "samsung,exynos5-sata" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> +- samsung,sata-freq : <frequency in MHz> + +Example: + sata@ffe08000 { + compatible = "samsung,exynos5-sata"; + reg = <0xffe08000 0x1000>; + interrupts = <115>; + }; diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt index d2fe064a828..63dd8051521 100644 --- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt @@ -2,9 +2,27 @@ properties: - compatible : Should be "ti,omap-ocp2scp" +- reg : Address and length of the register set for the device - #address-cells, #size-cells : Must be present if the device has sub-nodes - ranges : the child address space are mapped 1:1 onto the parent address space - ti,hwmods : must be "ocp2scp_usb_phy" Sub-nodes: All the devices connected to ocp2scp are described using sub-node to ocp2scp + +ocp2scp@4a0ad000 { + compatible = "ti,omap-ocp2scp"; + reg = <0x4a0ad000 0x1f>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "ocp2scp_usb_phy"; + + subnode1 { + ... + }; + + subnode2 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt index a0b867ef8d9..baadbb11fe9 100644 --- a/Documentation/devicetree/bindings/clock/imx23-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -52,7 +52,7 @@ clocks and IDs. lcdif 38 etm 39 usb 40 - usb_pwr 41 + usb_phy 41 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt new file mode 100644 index 00000000000..c2a3525ecb4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -0,0 +1,162 @@ +* Clock bindings for Freescale i.MX25 + +Required properties: +- compatible: Should be "fsl,imx25-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX25 +clocks and IDs. + + Clock ID + --------------------------- + dummy 0 + osc 1 + mpll 2 + upll 3 + mpll_cpu_3_4 4 + cpu_sel 5 + cpu 6 + ahb 7 + usb_div 8 + ipg 9 + per0_sel 10 + per1_sel 11 + per2_sel 12 + per3_sel 13 + per4_sel 14 + per5_sel 15 + per6_sel 16 + per7_sel 17 + per8_sel 18 + per9_sel 19 + per10_sel 20 + per11_sel 21 + per12_sel 22 + per13_sel 23 + per14_sel 24 + per15_sel 25 + per0 26 + per1 27 + per2 28 + per3 29 + per4 30 + per5 31 + per6 32 + per7 33 + per8 34 + per9 35 + per10 36 + per11 37 + per12 38 + per13 39 + per14 40 + per15 41 + csi_ipg_per 42 + epit_ipg_per 43 + esai_ipg_per 44 + esdhc1_ipg_per 45 + esdhc2_ipg_per 46 + gpt_ipg_per 47 + i2c_ipg_per 48 + lcdc_ipg_per 49 + nfc_ipg_per 50 + owire_ipg_per 51 + pwm_ipg_per 52 + sim1_ipg_per 53 + sim2_ipg_per 54 + ssi1_ipg_per 55 + ssi2_ipg_per 56 + uart_ipg_per 57 + ata_ahb 58 + reserved 59 + csi_ahb 60 + emi_ahb 61 + esai_ahb 62 + esdhc1_ahb 63 + esdhc2_ahb 64 + fec_ahb 65 + lcdc_ahb 66 + rtic_ahb 67 + sdma_ahb 68 + slcdc_ahb 69 + usbotg_ahb 70 + reserved 71 + reserved 72 + reserved 73 + reserved 74 + can1_ipg 75 + can2_ipg 76 + csi_ipg 77 + cspi1_ipg 78 + cspi2_ipg 79 + cspi3_ipg 80 + dryice_ipg 81 + ect_ipg 82 + epit1_ipg 83 + epit2_ipg 84 + reserved 85 + esdhc1_ipg 86 + esdhc2_ipg 87 + fec_ipg 88 + reserved 89 + reserved 90 + reserved 91 + gpt1_ipg 92 + gpt2_ipg 93 + gpt3_ipg 94 + gpt4_ipg 95 + reserved 96 + reserved 97 + reserved 98 + iim_ipg 99 + reserved 100 + reserved 101 + kpp_ipg 102 + lcdc_ipg 103 + reserved 104 + pwm1_ipg 105 + pwm2_ipg 106 + pwm3_ipg 107 + pwm4_ipg 108 + rngb_ipg 109 + reserved 110 + scc_ipg 111 + sdma_ipg 112 + sim1_ipg 113 + sim2_ipg 114 + slcdc_ipg 115 + spba_ipg 116 + ssi1_ipg 117 + ssi2_ipg 118 + tsc_ipg 119 + uart1_ipg 120 + uart2_ipg 121 + uart3_ipg 122 + uart4_ipg 123 + uart5_ipg 124 + reserved 125 + wdt_ipg 126 + +Examples: + +clks: ccm@53f80000 { + compatible = "fsl,imx25-ccm"; + reg = <0x53f80000 0x4000>; + interrupts = <31>; + clock-output-names = ... + "uart_ipg", + "uart_serial", + ...; +}; + +uart1: serial@43f90000 { + compatible = "fsl,imx25-uart", "fsl,imx21-uart"; + reg = <0x43f90000 0x4000>; + interrupts = <45>; + clocks = <&clks 79>, <&clks 50>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt index aa2af2866fe..52a49a4a50b 100644 --- a/Documentation/devicetree/bindings/clock/imx28-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -73,8 +73,8 @@ clocks and IDs. can1 59 usb0 60 usb1 61 - usb0_pwr 62 - usb1_pwr 63 + usb0_phy 62 + usb1_phy 63 enet_out 64 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt new file mode 100644 index 00000000000..04ad47876be --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt @@ -0,0 +1,191 @@ +* Clock bindings for Freescale i.MX5 + +Required properties: +- compatible: Should be "fsl,<soc>-ccm" , where <soc> can be imx51 or imx53 +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX5 +clocks and IDs. + + Clock ID + --------------------------- + dummy 0 + ckil 1 + osc 2 + ckih1 3 + ckih2 4 + ahb 5 + ipg 6 + axi_a 7 + axi_b 8 + uart_pred 9 + uart_root 10 + esdhc_a_pred 11 + esdhc_b_pred 12 + esdhc_c_s 13 + esdhc_d_s 14 + emi_sel 15 + emi_slow_podf 16 + nfc_podf 17 + ecspi_pred 18 + ecspi_podf 19 + usboh3_pred 20 + usboh3_podf 21 + usb_phy_pred 22 + usb_phy_podf 23 + cpu_podf 24 + di_pred 25 + tve_di 26 + tve_s 27 + uart1_ipg_gate 28 + uart1_per_gate 29 + uart2_ipg_gate 30 + uart2_per_gate 31 + uart3_ipg_gate 32 + uart3_per_gate 33 + i2c1_gate 34 + i2c2_gate 35 + gpt_ipg_gate 36 + pwm1_ipg_gate 37 + pwm1_hf_gate 38 + pwm2_ipg_gate 39 + pwm2_hf_gate 40 + gpt_hf_gate 41 + fec_gate 42 + usboh3_per_gate 43 + esdhc1_ipg_gate 44 + esdhc2_ipg_gate 45 + esdhc3_ipg_gate 46 + esdhc4_ipg_gate 47 + ssi1_ipg_gate 48 + ssi2_ipg_gate 49 + ssi3_ipg_gate 50 + ecspi1_ipg_gate 51 + ecspi1_per_gate 52 + ecspi2_ipg_gate 53 + ecspi2_per_gate 54 + cspi_ipg_gate 55 + sdma_gate 56 + emi_slow_gate 57 + ipu_s 58 + ipu_gate 59 + nfc_gate 60 + ipu_di1_gate 61 + vpu_s 62 + vpu_gate 63 + vpu_reference_gate 64 + uart4_ipg_gate 65 + uart4_per_gate 66 + uart5_ipg_gate 67 + uart5_per_gate 68 + tve_gate 69 + tve_pred 70 + esdhc1_per_gate 71 + esdhc2_per_gate 72 + esdhc3_per_gate 73 + esdhc4_per_gate 74 + usb_phy_gate 75 + hsi2c_gate 76 + mipi_hsc1_gate 77 + mipi_hsc2_gate 78 + mipi_esc_gate 79 + mipi_hsp_gate 80 + ldb_di1_div_3_5 81 + ldb_di1_div 82 + ldb_di0_div_3_5 83 + ldb_di0_div 84 + ldb_di1_gate 85 + can2_serial_gate 86 + can2_ipg_gate 87 + i2c3_gate 88 + lp_apm 89 + periph_apm 90 + main_bus 91 + ahb_max 92 + aips_tz1 93 + aips_tz2 94 + tmax1 95 + tmax2 96 + tmax3 97 + spba 98 + uart_sel 99 + esdhc_a_sel 100 + esdhc_b_sel 101 + esdhc_a_podf 102 + esdhc_b_podf 103 + ecspi_sel 104 + usboh3_sel 105 + usb_phy_sel 106 + iim_gate 107 + usboh3_gate 108 + emi_fast_gate 109 + ipu_di0_gate 110 + gpc_dvfs 111 + pll1_sw 112 + pll2_sw 113 + pll3_sw 114 + ipu_di0_sel 115 + ipu_di1_sel 116 + tve_ext_sel 117 + mx51_mipi 118 + pll4_sw 119 + ldb_di1_sel 120 + di_pll4_podf 121 + ldb_di0_sel 122 + ldb_di0_gate 123 + usb_phy1_gate 124 + usb_phy2_gate 125 + per_lp_apm 126 + per_pred1 127 + per_pred2 128 + per_podf 129 + per_root 130 + ssi_apm 131 + ssi1_root_sel 132 + ssi2_root_sel 133 + ssi3_root_sel 134 + ssi_ext1_sel 135 + ssi_ext2_sel 136 + ssi_ext1_com_sel 137 + ssi_ext2_com_sel 138 + ssi1_root_pred 139 + ssi1_root_podf 140 + ssi2_root_pred 141 + ssi2_root_podf 142 + ssi_ext1_pred 143 + ssi_ext1_podf 144 + ssi_ext2_pred 145 + ssi_ext2_podf 146 + ssi1_root_gate 147 + ssi2_root_gate 148 + ssi3_root_gate 149 + ssi_ext1_gate 150 + ssi_ext2_gate 151 + epit1_ipg_gate 152 + epit1_hf_gate 153 + epit2_ipg_gate 154 + epit2_hf_gate 155 + can_sel 156 + can1_serial_gate 157 + can1_ipg_gate 158 + +Examples (for mx53): + +clks: ccm@53fd4000{ + compatible = "fsl,imx53-ccm"; + reg = <0x53fd4000 0x4000>; + interrupts = <0 71 0x04 0 72 0x04>; + #clock-cells = <1>; +}; + +can1: can@53fc8000 { + compatible = "fsl,imx53-flexcan", "fsl,p1010-flexcan"; + reg = <0x53fc8000 0x4000>; + interrupts = <82>; + clocks = <&clks 158>, <&clks 157>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index 492bd991d52..d77b4e68dc4 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -187,9 +187,9 @@ clocks and IDs. pll3_usb_otg 172 pll4_audio 173 pll5_video 174 - pll6_mlb 175 + pll8_mlb 175 pll7_usb_host 176 - pll8_enet 177 + pll6_enet 177 ssi1_ipg 178 ssi2_ipg 179 ssi3_ipg 180 @@ -198,6 +198,11 @@ clocks and IDs. usbphy2 183 ldb_di0_div_3_5 184 ldb_di1_div_3_5 185 + sata_ref 186 + sata_ref_100m 187 + pcie_ref 188 + pcie_ref_125m 189 + enet_ref 190 Examples: diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt new file mode 100644 index 00000000000..1e662948661 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt @@ -0,0 +1,47 @@ +* Core Clock bindings for Marvell MVEBU SoCs + +Marvell MVEBU SoCs usually allow to determine core clock frequencies by +reading the Sample-At-Reset (SAR) register. The core clock consumer should +specify the desired clock by having the clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs and clock names on Armada 370/XP: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = nbclk (L2 Cache clock) + 3 = hclk (DRAM control clock) + 4 = dramclk (DDR clock) + +The following is a list of provided IDs and clock names on Kirkwood and Dove: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU0 clock) + 2 = l2clk (L2 Cache clock derived from CPU0 clock) + 3 = ddrclk (DDR controller clock derived from CPU0 clock) + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-370-core-clock" - For Armada 370 SoC core clocks + "marvell,armada-xp-core-clock" - For Armada XP SoC core clocks + "marvell,dove-core-clock" - for Dove SoC core clocks + "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) + "marvell,mv88f6180-core-clock" - for Kirkwood MV88f6180 SoC +- reg : shall be the register address of the Sample-At-Reset (SAR) register +- #clock-cells : from common clock binding; shall be set to 1 + +Optional properties: +- clock-output-names : from common clock binding; allows overwrite default clock + output names ("tclk", "cpuclk", "l2clk", "ddrclk") + +Example: + +core_clk: core-clocks@d0214 { + compatible = "marvell,dove-core-clock"; + reg = <0xd0214 0x4>; + #clock-cells = <1>; +}; + +spi0: spi@10600 { + compatible = "marvell,orion-spi"; + /* ... */ + /* get tclk from core clock provider */ + clocks = <&core_clk 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt new file mode 100644 index 00000000000..feb83013071 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt @@ -0,0 +1,21 @@ +Device Tree Clock bindings for cpu clock of Marvell EBU platforms + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP +- reg : Address and length of the clock complex register set +- #clock-cells : should be set to 1. +- clocks : shall be the input parent clock phandle for the clock. + +cpuclk: clock-complex@d0018700 { + #clock-cells = <1>; + compatible = "marvell,armada-xp-cpu-clock"; + reg = <0xd0018700 0xA0>; + clocks = <&coreclk 1>; +} + +cpu@0 { + compatible = "marvell,sheeva-v7"; + reg = <0>; + clocks = <&cpuclk 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt new file mode 100644 index 00000000000..7337005ef5e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -0,0 +1,119 @@ +* Gated Clock bindings for Marvell Orion SoCs + +Marvell Dove and Kirkwood allow some peripheral clocks to be gated to save +some power. The clock consumer should specify the desired clock by having +the clock ID in its "clocks" phandle cell. The clock ID is directly mapped to +the corresponding clock gating control bit in HW to ease manual clock lookup +in datasheet. + +The following is a list of provided IDs for Armada 370: +ID Clock Peripheral +----------------------------------- +0 Audio AC97 Cntrl +1 pex0_en PCIe 0 Clock out +2 pex1_en PCIe 1 Clock out +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex0 PCIe Cntrl 0 +9 pex1 PCIe Cntrl 1 +15 sata0 SATA Host 0 +17 sdio SDHCI Host +25 tdm Time Division Mplx +28 ddr DDR Cntrl +30 sata1 SATA Host 0 + +The following is a list of provided IDs for Armada XP: +ID Clock Peripheral +----------------------------------- +0 audio Audio Cntrl +1 ge3 Gigabit Ethernet 3 +2 ge2 Gigabit Ethernet 2 +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex0 PCIe Cntrl 0 +6 pex1 PCIe Cntrl 1 +7 pex2 PCIe Cntrl 2 +8 pex3 PCIe Cntrl 3 +13 bp +14 sata0lnk +15 sata0 SATA Host 0 +16 lcd LCD Cntrl +17 sdio SDHCI Host +18 usb0 USB Host 0 +19 usb1 USB Host 1 +20 usb2 USB Host 2 +22 xor0 XOR DMA 0 +23 crypto CESA engine +25 tdm Time Division Mplx +28 xor1 XOR DMA 1 +29 sata1lnk +30 sata1 SATA Host 0 + +The following is a list of provided IDs for Dove: +ID Clock Peripheral +----------------------------------- +0 usb0 USB Host 0 +1 usb1 USB Host 1 +2 ge Gigabit Ethernet +3 sata SATA Host +4 pex0 PCIe Cntrl 0 +5 pex1 PCIe Cntrl 1 +8 sdio0 SDHCI Host 0 +9 sdio1 SDHCI Host 1 +10 nand NAND Cntrl +11 camera Camera Cntrl +12 i2s0 I2S Cntrl 0 +13 i2s1 I2S Cntrl 1 +15 crypto CESA engine +21 ac97 AC97 Cntrl +22 pdma Peripheral DMA +23 xor0 XOR DMA 0 +24 xor1 XOR DMA 1 +30 gephy Gigabit Ethernel PHY +Note: gephy(30) is implemented as a parent clock of ge(2) + +The following is a list of provided IDs for Kirkwood: +ID Clock Peripheral +----------------------------------- +0 ge0 Gigabit Ethernet 0 +2 pex0 PCIe Cntrl 0 +3 usb0 USB Host 0 +4 sdio SDIO Cntrl +5 tsu Transp. Stream Unit +6 dunit SDRAM Cntrl +7 runit Runit +8 xor0 XOR DMA 0 +9 audio I2S Cntrl 0 +14 sata0 SATA Host 0 +15 sata1 SATA Host 1 +16 xor1 XOR DMA 1 +17 crypto CESA engine +18 pex1 PCIe Cntrl 1 +19 ge1 Gigabit Ethernet 0 +20 tdm Time Division Mplx + +Required properties: +- compatible : shall be one of the following: + "marvell,dove-gating-clock" - for Dove SoC clock gating + "marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating +- reg : shall be the register address of the Clock Gating Control register +- #clock-cells : from common clock binding; shall be set to 1 + +Optional properties: +- clocks : default parent clock phandle (e.g. tclk) + +Example: + +gate_clk: clock-gating-control@d0038 { + compatible = "marvell,dove-gating-clock"; + reg = <0xd0038 0x4>; + /* default parent clock is tclk */ + clocks = <&core_clk 0>; + #clock-cells = <1>; +}; + +sdio0: sdio@92000 { + compatible = "marvell,dove-sdhci"; + /* get clk gate bit 8 (sdio0) */ + clocks = <&gate_clk 8>; +}; diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt new file mode 100644 index 00000000000..23ae1db1bc1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt @@ -0,0 +1,55 @@ +Device Tree Clock bindings for the Zynq 7000 EPP + +The Zynq EPP has several different clk providers, each with there own bindings. +The purpose of this document is to document their usage. + +See clock_bindings.txt for more information on the generic clock bindings. +See Chapter 25 of Zynq TRM for more information about Zynq clocks. + +== PLLs == + +Used to describe the ARM_PLL, DDR_PLL, and IO_PLL. + +Required properties: +- #clock-cells : shall be 0 (only one clock is output from this node) +- compatible : "xlnx,zynq-pll" +- reg : pair of u32 values, which are the address offsets within the SLCR + of the relevant PLL_CTRL register and PLL_CFG register respectively +- clocks : phandle for parent clock. should be the phandle for ps_clk + +Optional properties: +- clock-output-names : name of the output clock + +Example: + armpll: armpll { + #clock-cells = <0>; + compatible = "xlnx,zynq-pll"; + clocks = <&ps_clk>; + reg = <0x100 0x110>; + clock-output-names = "armpll"; + }; + +== Peripheral clocks == + +Describes clock node for the SDIO, SMC, SPI, QSPI, and UART clocks. + +Required properties: +- #clock-cells : shall be 1 +- compatible : "xlnx,zynq-periph-clock" +- reg : a single u32 value, describing the offset within the SLCR where + the CLK_CTRL register is found for this peripheral +- clocks : phandle for parent clocks. should hold phandles for + the IO_PLL, ARM_PLL, and DDR_PLL in order +- clock-output-names : names of the output clock(s). For peripherals that have + two output clocks (for example, the UART), two clocks + should be listed. + +Example: + uart_clk: uart_clk { + #clock-cells = <1>; + compatible = "xlnx,zynq-periph-clock"; + clocks = <&iopll &armpll &ddrpll>; + reg = <0x154>; + clock-output-names = "uart0_ref_clk", + "uart1_ref_clk"; + }; diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt new file mode 100644 index 00000000000..f3d44984d91 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt @@ -0,0 +1,42 @@ +SPEAr cpufreq driver +------------------- + +SPEAr SoC cpufreq driver for CPU frequency scaling. +It supports both uniprocessor (UP) and symmetric multiprocessor (SMP) systems +which share clock across all CPUs. + +Required properties: +- cpufreq_tbl: Table of frequencies CPU could be transitioned into, in the + increasing order. + +Optional properties: +- clock-latency: Specify the possible maximum transition latency for clock, in + unit of nanoseconds. + +Both required and optional properties listed above must be defined under node +/cpus/cpu@0. + +Examples: +-------- +cpus { + + <...> + + cpu@0 { + compatible = "arm,cortex-a9"; + reg = <0>; + + <...> + + cpufreq_tbl = < 166000 + 200000 + 250000 + 300000 + 400000 + 500000 + 600000 >; + }; + + <...> + +}; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index bd7ce120bc1..fc9ce6f1688 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -54,7 +54,8 @@ PROPERTIES - compatible Usage: required Value type: <string> - Definition: Must include "fsl,sec-v4.0" + Definition: Must include "fsl,sec-v4.0". Also includes SEC + ERA versions (optional) with which the device is compatible. - #address-cells Usage: required @@ -106,7 +107,7 @@ PROPERTIES EXAMPLE crypto@300000 { - compatible = "fsl,sec-v4.0"; + compatible = "fsl,sec-v4.0", "fsl,sec-era-v2.0"; #address-cells = <1>; #size-cells = <1>; reg = <0x300000 0x10000>; diff --git a/Documentation/devicetree/bindings/dma/mv-xor.txt b/Documentation/devicetree/bindings/dma/mv-xor.txt new file mode 100644 index 00000000000..7c6cb7fcecd --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mv-xor.txt @@ -0,0 +1,40 @@ +* Marvell XOR engines + +Required properties: +- compatible: Should be "marvell,orion-xor" +- reg: Should contain registers location and length (two sets) + the first set is the low registers, the second set the high + registers for the XOR engine. +- clocks: pointer to the reference clock + +The DT node must also contains sub-nodes for each XOR channel that the +XOR engine has. Those sub-nodes have the following required +properties: +- interrupts: interrupt of the XOR channel + +And the following optional properties: +- dmacap,memcpy to indicate that the XOR channel is capable of memcpy operations +- dmacap,memset to indicate that the XOR channel is capable of memset operations +- dmacap,xor to indicate that the XOR channel is capable of xor operations + +Example: + +xor@d0060900 { + compatible = "marvell,orion-xor"; + reg = <0xd0060900 0x100 + 0xd0060b00 0x100>; + clocks = <&coreclk 0>; + status = "okay"; + + xor00 { + interrupts = <51>; + dmacap,memcpy; + dmacap,xor; + }; + xor01 { + interrupts = <52>; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmi.txt b/Documentation/devicetree/bindings/drm/exynos/hdmi.txt new file mode 100644 index 00000000000..589edee3739 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/hdmi.txt @@ -0,0 +1,22 @@ +Device-Tree bindings for drm hdmi driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmi". +- reg: physical base address of the hdmi and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- hpd-gpio: following information about the hotplug gpio pin. + a) phandle of the gpio controller node. + b) pin number within the gpio controller. + c) pin function mode. + d) optional flags and pull up/down. + e) drive strength. + +Example: + + hdmi { + compatible = "samsung,exynos5-hdmi"; + reg = <0x14530000 0x100000>; + interrupts = <0 95 0>; + hpd-gpio = <&gpx3 7 0xf 1 3>; + }; diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt b/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt new file mode 100644 index 00000000000..fa166d94580 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt @@ -0,0 +1,12 @@ +Device-Tree bindings for hdmiddc driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmiddc". +- reg: I2C address of the hdmiddc device. + +Example: + + hdmiddc { + compatible = "samsung,exynos5-hdmiddc"; + reg = <0x50>; + }; diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt b/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt new file mode 100644 index 00000000000..858f4f9b902 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt @@ -0,0 +1,12 @@ +Device-Tree bindings for hdmiphy driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmiphy". +- reg: I2C address of the hdmiphy device. + +Example: + + hdmiphy { + compatible = "samsung,exynos5-hdmiphy"; + reg = <0x38>; + }; diff --git a/Documentation/devicetree/bindings/drm/exynos/mixer.txt b/Documentation/devicetree/bindings/drm/exynos/mixer.txt new file mode 100644 index 00000000000..9b2ea034356 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/mixer.txt @@ -0,0 +1,15 @@ +Device-Tree bindings for mixer driver + +Required properties: +- compatible: value should be "samsung,exynos5-mixer". +- reg: physical base address of the mixer and length of memory mapped + region. +- interrupts: interrupt number to the cpu. + +Example: + + mixer { + compatible = "samsung,exynos5-mixer"; + reg = <0x14450000 0x10000>; + interrupts = <0 94 0>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt new file mode 100644 index 00000000000..558cdf3c9ab --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt @@ -0,0 +1,22 @@ +GPIO line that should be set high/low to power off a device + +Required properties: +- compatible : should be "gpio-poweroff". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to power down the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- input : Initially configure the GPIO line as an input. Only reconfigure + it to an output when the pm_power_off function is called. If this optional + property is not specified, the GPIO is initialized as an output in its + inactive state. + + +Examples: + +gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 4 0>; /* GPIO 4 Active Low */ +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt b/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt new file mode 100644 index 00000000000..a0e4cf88521 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt @@ -0,0 +1,18 @@ +STMPE gpio +---------- + +Required properties: + - compatible: "st,stmpe-gpio" + +Optional properties: + - st,norequest-mask: bitmask specifying which GPIOs should _not_ be requestable + due to different usage (e.g. touch, keypad) + +Node name must be stmpe_gpio and should be child node of stmpe node to which it +belongs. + +Example: + stmpe_gpio { + compatible = "st,stmpe-gpio"; + st,norequest-mask = <0x20>; //gpio 5 can't be used + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 4e16ba4feab..a33628759d3 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -75,4 +75,40 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: gpio-controller; }; +2.1) gpio-controller and pinctrl subsystem +------------------------------------------ +gpio-controller on a SOC might be tightly coupled with the pinctrl +subsystem, in the sense that the pins can be used by other functions +together with optional gpio feature. + +While the pin allocation is totally managed by the pin ctrl subsystem, +gpio (under gpiolib) is still maintained by gpio drivers. It may happen +that different pin ranges in a SoC is managed by different gpio drivers. + +This makes it logical to let gpio drivers announce their pin ranges to +the pin ctrl subsystem and call 'pinctrl_request_gpio' in order to +request the corresponding pin before any gpio usage. + +For this, the gpio controller can use a pinctrl phandle and pins to +announce the pinrange to the pin ctrl subsystem. For example, + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>; + + } + +where, + &pinctrl1 and &pinctrl2 is the phandle to the pinctrl DT node. + + Next values specify the base pin and number of pins for the range + handled by 'qe_pio_e' gpio. In the given example from base pin 20 to + pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled + by this gpio controller. + +The pinctrl node must have "#gpio-range-cells" property to show number of +arguments to pass with phandle from gpio controllers node. diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt index 66efc804806..85f8c0d084f 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -9,6 +9,10 @@ Required properties: unused). - gpio-controller: Marks the device node as a GPIO controller. +optional properties: +- #gpio-lines: Number of gpio if absent 32. + + Example: pioA: gpio@fffff200 { compatible = "atmel,at91rm9200-gpio"; @@ -16,5 +20,6 @@ Example: interrupts = <2 4>; #gpio-cells = <2>; gpio-controller; + #gpio-lines = <19>; }; diff --git a/Documentation/devicetree/bindings/gpio/leds-ns2.txt b/Documentation/devicetree/bindings/gpio/leds-ns2.txt new file mode 100644 index 00000000000..aef3aca34d2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/leds-ns2.txt @@ -0,0 +1,26 @@ +Binding for dual-GPIO LED found on Network Space v2 (and parents). + +Required properties: +- compatible: "lacie,ns2-leds". + +Each LED is represented as a sub-node of the ns2-leds device. + +Required sub-node properties: +- cmd-gpio: Command LED GPIO. See OF device-tree GPIO specification. +- slow-gpio: Slow LED GPIO. See OF device-tree GPIO specification. + +Optional sub-node properties: +- label: Name for this LED. If omitted, the label is taken from the node name. +- linux,default-trigger: Trigger assigned to the LED. + +Example: + +ns2-leds { + compatible = "lacie,ns2-leds"; + + blue-sata { + label = "ns2:blue:sata"; + slow-gpio = <&gpio0 29 0>; + cmd-gpio = <&gpio0 30 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/spear_spics.txt b/Documentation/devicetree/bindings/gpio/spear_spics.txt new file mode 100644 index 00000000000..96c37eb1507 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/spear_spics.txt @@ -0,0 +1,50 @@ +=== ST Microelectronics SPEAr SPI CS Driver === + +SPEAr platform provides a provision to control chipselects of ARM PL022 Prime +Cell spi controller through its system registers, which otherwise remains under +PL022 control. If chipselect remain under PL022 control then they would be +released as soon as transfer is over and TxFIFO becomes empty. This is not +desired by some of the device protocols above spi which expect (multiple) +transfers without releasing their chipselects. + +Chipselects can be controlled by software by turning them as GPIOs. SPEAr +provides another interface through system registers through which software can +directly control each PL022 chipselect. Hence, it is natural for SPEAr to export +the control of this interface as gpio. + +Required properties: + + * compatible: should be defined as "st,spear-spics-gpio" + * reg: mentioning address range of spics controller + * st-spics,peripcfg-reg: peripheral configuration register offset + * st-spics,sw-enable-bit: bit offset to enable sw control + * st-spics,cs-value-bit: bit offset to drive chipselect low or high + * st-spics,cs-enable-mask: chip select number bit mask + * st-spics,cs-enable-shift: chip select number program offset + * gpio-controller: Marks the device node as gpio controller + * #gpio-cells: should be 1 and will mention chip select number + +All the above bit offsets are within peripcfg register. + +Example: +------- +spics: spics@e0700000{ + compatible = "st,spear-spics-gpio"; + reg = <0xe0700000 0x1000>; + st-spics,peripcfg-reg = <0x3b0>; + st-spics,sw-enable-bit = <12>; + st-spics,cs-value-bit = <11>; + st-spics,cs-enable-mask = <3>; + st-spics,cs-enable-shift = <8>; + gpio-controller; + #gpio-cells = <2>; +}; + + +spi0: spi@e0100000 { + status = "okay"; + num-cs = <3>; + cs-gpios = <&gpio1 7 0>, <&spics 0>, + <&spics 1>; + ... +} diff --git a/Documentation/devicetree/bindings/hwmon/vexpress.txt b/Documentation/devicetree/bindings/hwmon/vexpress.txt new file mode 100644 index 00000000000..9c27ed694bb --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/vexpress.txt @@ -0,0 +1,23 @@ +Versatile Express hwmon sensors +------------------------------- + +Requires node properties: +- "compatible" value : one of + "arm,vexpress-volt" + "arm,vexpress-amp" + "arm,vexpress-temp" + "arm,vexpress-power" + "arm,vexpress-energy" +- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg + (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt + for more details) + +Optional node properties: +- label : string describing the monitored value + +Example: + energy@0 { + compatible = "arm,vexpress-energy"; + arm,vexpress-sysreg,func = <13 0>; + label = "A15 Jcore"; + }; diff --git a/Documentation/devicetree/bindings/i2c/atmel-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt index b689a0d9441..b689a0d9441 100644 --- a/Documentation/devicetree/bindings/i2c/atmel-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt new file mode 100644 index 00000000000..8ce9cd2855b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt @@ -0,0 +1,27 @@ +Device tree bindings for i2c-cbus-gpio driver + +Required properties: + - compatible = "i2c-cbus-gpio"; + - gpios: clk, dat, sel + - #address-cells = <1>; + - #size-cells = <0>; + +Optional properties: + - child nodes conforming to i2c bus binding + +Example: + +i2c@0 { + compatible = "i2c-cbus-gpio"; + gpios = <&gpio 66 0 /* clk */ + &gpio 65 0 /* dat */ + &gpio 64 0 /* sel */ + >; + #address-cells = <1>; + #size-cells = <0>; + + retu-mfd: retu@1 { + compatible = "retu-mfd"; + reg = <0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt index 2dc935b4113..2dc935b4113 100644 --- a/Documentation/devicetree/bindings/i2c/davinci.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt diff --git a/Documentation/devicetree/bindings/i2c/gpio-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt index 4f8ec947c6b..4f8ec947c6b 100644 --- a/Documentation/devicetree/bindings/i2c/gpio-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt diff --git a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index f3cf43b66f7..3614242e773 100644 --- a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -12,13 +12,13 @@ Optional properties: Examples: i2c@83fc4000 { /* I2C2 on i.MX51 */ - compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; reg = <0x83fc4000 0x4000>; interrupts = <63>; }; i2c@70038000 { /* HS-I2C on i.MX51 */ - compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; reg = <0x70038000 0x4000>; interrupts = <64>; clock-frequency = <400000>; diff --git a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt index 1eacd6b20ed..1eacd6b20ed 100644 --- a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt new file mode 100644 index 00000000000..66709a82554 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt @@ -0,0 +1,81 @@ +GPIO-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses GPIOs to +route the I2C signals. + + +-----+ +-----+ + | dev | | dev | + +------------+ +-----+ +-----+ + | SoC | | | + | | /--------+--------+ + | +------+ | +------+ child bus A, on GPIO value set to 0 + | | I2C |-|--| Mux | + | +------+ | +--+---+ child bus B, on GPIO value set to 1 + | | | \----------+--------+--------+ + | +------+ | | | | | + | | GPIO |-|-----+ +-----+ +-----+ +-----+ + | +------+ | | dev | | dev | | dev | + +------------+ +-----+ +-----+ +-----+ + +Required properties: +- compatible: i2c-mux-gpio +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. +- mux-gpios: list of gpios used to control the muxer +* Standard I2C mux properties. See mux.txt in this directory. +* I2C child bus nodes. See mux.txt in this directory. + +Optional properties: +- idle-state: value to set the muxer to when idle. When no value is + given, it defaults to the last value used. + +For each i2c child node, an I2C child bus will be created. They will +be numbered based on their order in the device tree. + +Whenever an access is made to a device on a child bus, the value set +in the revelant node's reg property will be output using the list of +GPIOs, the first in the list holding the least-significant value. + +If an idle state is defined, using the idle-state (optional) property, +whenever an access is not being made to a device on a child bus, the +GPIOs will be set according to the idle value. + +If an idle state is not defined, the most recently used value will be +left programmed into hardware whenever no access is being made to a +device on a child bus. + +Example: + i2cmux { + compatible = "i2c-mux-gpio"; + #address-cells = <1>; + #size-cells = <0>; + mux-gpios = <&gpio1 22 0 &gpio1 23 0>; + i2c-parent = <&i2c1>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7 1>; + reset-active-low; + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/mux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux.txt index af84cce5cd7..af84cce5cd7 100644 --- a/Documentation/devicetree/bindings/i2c/mux.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt new file mode 100644 index 00000000000..f46d928aa73 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -0,0 +1,18 @@ + +* Marvell MV64XXX I2C controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : Should be "marvell,mv64xxx-i2c" + - interrupts : The interrupt number + - clock-frequency : Desired I2C bus clock frequency in Hz. + +Examples: + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/nomadik.txt b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt index 72065b0ff68..72065b0ff68 100644 --- a/Documentation/devicetree/bindings/i2c/nomadik.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt index c15781f4dc8..1637c298a1b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -1,7 +1,7 @@ Device tree configuration for i2c-ocores Required properties: -- compatible : "opencores,i2c-ocores" +- compatible : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst" - reg : bus address start and address range size of device - interrupts : interrupt number - clock-frequency : frequency of bus clock in Hz diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt index dced82ebe31..dced82ebe31 100644 --- a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt diff --git a/Documentation/devicetree/bindings/i2c/omap-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-omap.txt index 56564aa4b44..56564aa4b44 100644 --- a/Documentation/devicetree/bindings/i2c/omap-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-omap.txt diff --git a/Documentation/devicetree/bindings/i2c/pnx.txt b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt index fe98ada33ee..fe98ada33ee 100644 --- a/Documentation/devicetree/bindings/i2c/pnx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt diff --git a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt index 569b1624851..569b1624851 100644 --- a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt index 0f7945019f6..12b78ac507e 100644 --- a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -31,21 +31,3 @@ Examples: reg = <0xd4025000 0x1000>; interrupts = <58>; }; - -* Marvell MV64XXX I2C controller - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible : Should be "marvell,mv64xxx-i2c" - - interrupts : The interrupt number - - clock-frequency : Desired I2C bus clock frequency in Hz. - -Examples: - - i2c@11000 { - compatible = "marvell,mv64xxx-i2c"; - reg = <0x11000 0x20>; - interrupts = <29>; - clock-frequency = <100000>; - }; diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index b6cb5a12c67..e9611ace879 100644 --- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -13,11 +13,17 @@ Required properties: - interrupts: interrupt number to the cpu. - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. +Required for all cases except "samsung,s3c2440-hdmiphy-i2c": + - Samsung GPIO variant (deprecated): + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. Required in all + cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output + lines are permanently wired to the respective clienta + - Pinctrl variant (preferred, if available): + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + Optional properties: - - gpios: The order of the gpios should be the following: <SDA, SCL>. - The gpio specifier depends on the gpio controller. Required in all - cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output - lines are permanently wired to the respective client - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not @@ -31,8 +37,14 @@ Example: interrupts = <345>; samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <100000>; + /* Samsung GPIO variant begins here */ gpios = <&gpd1 2 0 /* SDA */ &gpd1 3 0 /* SCL */>; + /* Samsung GPIO variant ends here */ + /* Pinctrl variant begins here */ + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + /* Pinctrl variant ends here */ #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt index 7baf9e133fa..7baf9e133fa 100644 --- a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt diff --git a/Documentation/devicetree/bindings/i2c/arm-versatile.txt b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt index 361d31c51b6..361d31c51b6 100644 --- a/Documentation/devicetree/bindings/i2c/arm-versatile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt diff --git a/Documentation/devicetree/bindings/i2c/xiic.txt b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt index ceabbe91ae4..ceabbe91ae4 100644 --- a/Documentation/devicetree/bindings/i2c/xiic.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 2f5322b119e..446859fcdca 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -55,5 +55,7 @@ st-micro,24c256 i2c serial eeprom (24cxx) stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS +taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp275 Digital Temperature Sensor diff --git a/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt new file mode 100644 index 00000000000..ead641c65e0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt @@ -0,0 +1,46 @@ +* GPIO driven matrix keypad device tree bindings + +GPIO driven matrix keypad is used to interface a SoC with a matrix keypad. +The matrix keypad supports multiple row and column lines, a key can be +placed at each intersection of a unique row and a unique column. The matrix +keypad can sense a key-press and key-release by means of GPIO lines and +report the event using GPIO interrupts to the cpu. + +Required Properties: +- compatible: Should be "gpio-matrix-keypad" +- row-gpios: List of gpios used as row lines. The gpio specifier + for this property depends on the gpio controller to + which these row lines are connected. +- col-gpios: List of gpios used as column lines. The gpio specifier + for this property depends on the gpio controller to + which these column lines are connected. +- linux,keymap: The definition can be found at + bindings/input/matrix-keymap.txt + +Optional Properties: +- linux,no-autorepeat: do no enable autorepeat feature. +- linux,wakeup: use any event on keypad as wakeup event. +- debounce-delay-ms: debounce interval in milliseconds +- col-scan-delay-us: delay, measured in microseconds, that is needed + before we can scan keypad after activating column gpio + +Example: + matrix-keypad { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio2 25 0 + &gpio2 26 0 + &gpio2 27 0>; + + col-gpios = <&gpio2 21 0 + &gpio2 22 0>; + + linux,keymap = <0x0000008B + 0x0100009E + 0x02000069 + 0x0001006A + 0x0101001C + 0x0201006C>; + }; diff --git a/Documentation/devicetree/bindings/input/pwm-beeper.txt b/Documentation/devicetree/bindings/input/pwm-beeper.txt new file mode 100644 index 00000000000..be332ae4f2d --- /dev/null +++ b/Documentation/devicetree/bindings/input/pwm-beeper.txt @@ -0,0 +1,7 @@ +* PWM beeper device tree bindings + +Registers a PWM device as beeper. + +Required properties: +- compatible: should be "pwm-beeper" +- pwms: phandle to the physical PWM device diff --git a/Documentation/devicetree/bindings/input/stmpe-keypad.txt b/Documentation/devicetree/bindings/input/stmpe-keypad.txt new file mode 100644 index 00000000000..1b97222e8a0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/stmpe-keypad.txt @@ -0,0 +1,39 @@ +* STMPE Keypad + +Required properties: + - compatible : "st,stmpe-keypad" + - linux,keymap : See ./matrix-keymap.txt + +Optional properties: + - debounce-interval : Debouncing interval time in milliseconds + - st,scan-count : Scanning cycles elapsed before key data is updated + - st,no-autorepeat : If specified device will not autorepeat + +Example: + + stmpe_keypad { + compatible = "st,stmpe-keypad"; + + debounce-interval = <64>; + st,scan-count = <8>; + st,no-autorepeat; + + linux,keymap = <0x205006b + 0x4010074 + 0x3050072 + 0x1030004 + 0x502006a + 0x500000a + 0x5008b + 0x706001c + 0x405000b + 0x6070003 + 0x3040067 + 0x303006c + 0x60400e7 + 0x602009e + 0x4020073 + 0x5050002 + 0x4030069 + 0x3020008>; + }; diff --git a/Documentation/devicetree/bindings/input/tca8418_keypad.txt b/Documentation/devicetree/bindings/input/tca8418_keypad.txt new file mode 100644 index 00000000000..2a1538f0053 --- /dev/null +++ b/Documentation/devicetree/bindings/input/tca8418_keypad.txt @@ -0,0 +1,8 @@ + +Required properties: +- compatible: "ti,tca8418" +- reg: the I2C address +- interrupts: IRQ line number, should trigger on falling edge +- keypad,num-rows: The number of rows +- keypad,num-columns: The number of columns +- linux,keymap: Keys definitions, see keypad-matrix. diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt new file mode 100644 index 00000000000..ca5a2c86480 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt @@ -0,0 +1,28 @@ +* Rohm BU21013 Touch Screen + +Required properties: + - compatible : "rohm,bu21013_tp" + - reg : I2C device address + +Optional properties: + - touch-gpio : GPIO pin registering a touch event + - <supply_name>-supply : Phandle to a regulator supply + - rohm,touch-max-x : Maximum outward permitted limit in the X axis + - rohm,touch-max-y : Maximum outward permitted limit in the Y axis + - rohm,flip-x : Flip touch coordinates on the X axis + - rohm,flip-y : Flip touch coordinates on the Y axis + +Example: + + i2c@80110000 { + bu21013_tp@0x5c { + compatible = "rohm,bu21013_tp"; + reg = <0x5c>; + touch-gpio = <&gpio2 20 0x4>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + + rohm,touch-max-x = <384>; + rohm,touch-max-y = <704>; + rohm,flip-y; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/mms114.txt b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt new file mode 100644 index 00000000000..89d4c56c567 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt @@ -0,0 +1,34 @@ +* MELFAS MMS114 touchscreen controller + +Required properties: +- compatible: must be "melfas,mms114" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Optional properties: +- contact-threshold: +- moving-threshold: +- x-invert: invert X axis +- y-invert: invert Y axis + +Example: + + i2c@00000000 { + /* ... */ + + touchscreen@48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupts = <39 0>; + x-size = <720>; + y-size = <1280>; + contact-threshold = <10>; + moving-threshold = <10>; + x-invert; + y-invert; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt new file mode 100644 index 00000000000..127baa31a77 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -0,0 +1,43 @@ +STMPE Touchscreen +---------------- + +Required properties: + - compatible: "st,stmpe-ts" + +Optional properties: +- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> + 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 + -> 144 clocks), recommended is 4. +- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) +- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external + reference) +- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) +- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 + samples, 3 -> 8 samples) +- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> + 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended + is 3 +- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 + -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 +- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of + the fractional part) recommended is 7 +- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 + mA max, 1 -> 50 mA typical 80 mA max) + +Node name must be stmpe_touchscreen and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt new file mode 100644 index 00000000000..7f9fb85f545 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt @@ -0,0 +1,104 @@ +Allwinner Sunxi Interrupt Controller + +Required properties: + +- compatible : should be "allwinner,sunxi-ic" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + +The interrupt sources are as follows: + +0: ENMI +1: UART0 +2: UART1 +3: UART2 +4: UART3 +5: IR0 +6: IR1 +7: I2C0 +8: I2C1 +9: I2C2 +10: SPI0 +11: SPI1 +12: SPI2 +13: SPDIF +14: AC97 +15: TS +16: I2S +17: UART4 +18: UART5 +19: UART6 +20: UART7 +21: KEYPAD +22: TIMER0 +23: TIMER1 +24: TIMER2 +25: TIMER3 +26: CAN +27: DMA +28: PIO +29: TOUCH_PANEL +30: AUDIO_CODEC +31: LRADC +32: SDMC0 +33: SDMC1 +34: SDMC2 +35: SDMC3 +36: MEMSTICK +37: NAND +38: USB0 +39: USB1 +40: USB2 +41: SCR +42: CSI0 +43: CSI1 +44: LCDCTRL0 +45: LCDCTRL1 +46: MP +47: DEFEBE0 +48: DEFEBE1 +49: PMU +50: SPI3 +51: TZASC +52: PATA +53: VE +54: SS +55: EMAC +56: SATA +57: GPS +58: HDMI +59: TVE +60: ACE +61: TVD +62: PS2_0 +63: PS2_1 +64: USB3 +65: USB4 +66: PLE_PFM +67: TIMER4 +68: TIMER5 +69: GPU_GP +70: GPU_GPMMU +71: GPU_PP0 +72: GPU_PPMMU0 +73: GPU_PMU +74: GPU_RSV0 +75: GPU_RSV1 +76: GPU_RSV2 +77: GPU_RSV3 +78: GPU_RSV4 +79: GPU_RSV5 +80: GPU_RSV6 +82: SYNC_TIMER0 +83: SYNC_TIMER1 + +Example: + +intc: interrupt-controller { + compatible = "allwinner,sunxi-ic"; + reg = <0x01c20400 0x400>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt new file mode 100644 index 00000000000..2d88816dd55 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -0,0 +1,23 @@ +Common leds properties. + +Optional properties for child nodes: +- label : The label for this LED. If omitted, the label is + taken from the node name (excluding the unit address). + +- linux,default-trigger : This parameter, if present, is a + string defining the trigger assigned to the LED. Current triggers are: + "backlight" - LED will act as a back-light, controlled by the framebuffer + system + "default-on" - LED will turn on (but for leds-gpio see "default-state" + property in Documentation/devicetree/bindings/gpio/led.txt) + "heartbeat" - LED "double" flashes at a load average based rate + "ide-disk" - LED indicates disk activity + "timer" - LED flashes at a fixed, configurable rate + +Examples: + +system-status { + label = "Status"; + linux,default-trigger = "heartbeat"; + ... +}; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index edc83c1c0d5..df1b3080f6b 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -10,16 +10,10 @@ LED sub-node properties: - gpios : Should specify the LED's GPIO, see "gpios property" in Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs should be indicated using flags in the GPIO specifier. -- label : (optional) The label for this LED. If omitted, the label is - taken from the node name (excluding the unit address). -- linux,default-trigger : (optional) This parameter, if present, is a - string defining the trigger assigned to the LED. Current triggers are: - "backlight" - LED will act as a back-light, controlled by the framebuffer - system - "default-on" - LED will turn on, but see "default-state" below - "heartbeat" - LED "double" flashes at a load average based rate - "ide-disk" - LED indicates disk activity - "timer" - LED flashes at a fixed, configurable rate +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt - default-state: (optional) The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is set the to same value, then no diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt new file mode 100644 index 00000000000..67ec3d4ccc7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -0,0 +1,23 @@ +* Samsung Multi Format Codec (MFC) + +Multi Format Codec (MFC) is the IP present in Samsung SoCs which +supports high resolution decoding and encoding functionalities. +The MFC device driver is a v4l2 driver which can encode/decode +video raw/elementary streams and has support for all popular +video codecs. + +Required properties: + - compatible : value should be either one among the following + (a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs + (b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : MFC interrupt number to the CPU. + + - samsung,mfc-r : Base address of the first memory bank used by MFC + for DMA contiguous memory allocation and its size. + + - samsung,mfc-l : Base address of the second memory bank used by MFC + for DMA contiguous memory allocation and its size. diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt index ce83c8d3c00..13b707b7355 100644 --- a/Documentation/devicetree/bindings/mfd/ab8500.txt +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -24,7 +24,32 @@ ab8500-bm : : : Battery Manager ab8500-btemp : : : Battery Temperature ab8500-charger : : : Battery Charger ab8500-codec : : : Audio Codec -ab8500-fg : : : Fuel Gauge +ab8500-fg : : vddadc : Fuel Gauge + : NCONV_ACCU : : Accumulate N Sample Conversion + : BATT_OVV : : Battery Over Voltage + : LOW_BAT_F : : LOW threshold battery voltage + : CC_INT_CALIB : : Coulomb Counter Internal Calibration + : CCEOC : : Coulomb Counter End of Conversion +ab8500-btemp : : vtvout : Battery Temperature + : BAT_CTRL_INDB : : Battery Removal Indicator + : BTEMP_LOW : : Btemp < BtempLow, if battery temperature is lower than -10°C + : BTEMP_LOW_MEDIUM : : BtempLow < Btemp < BtempMedium,if battery temperature is between -10 and 0°C + : BTEMP_MEDIUM_HIGH : : BtempMedium < Btemp < BtempHigh,if battery temperature is between 0°C and“MaxTemp + : BTEMP_HIGH : : Btemp > BtempHigh, if battery temperature is higher than “MaxTemp +ab8500-charger : : vddadc : Charger interface + : MAIN_CH_UNPLUG_DET : : main charger unplug detection management (not in 8505) + : MAIN_CHARGE_PLUG_DET : : main charger plug detection management (not in 8505) + : MAIN_EXT_CH_NOT_OK : : main charger not OK + : MAIN_CH_TH_PROT_R : : Die temp is above main charger + : MAIN_CH_TH_PROT_F : : Die temp is below main charger + : VBUS_DET_F : : VBUS falling detected + : VBUS_DET_R : : VBUS rising detected + : USB_LINK_STATUS : : USB link status has changed + : USB_CH_TH_PROT_R : : Die temp is above usb charger + : USB_CH_TH_PROT_F : : Die temp is below usb charger + : USB_CHARGER_NOT_OKR : : allowed USB charger not ok detection + : VBUS_OVV : : Overvoltage on Vbus ball detected (USB charge is stopped) + : CH_WD_EXP : : Charger watchdog detected ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter SW_CONV_END : : ab8500-gpio : : : GPIO Controller diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt new file mode 100644 index 00000000000..56edb552068 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -0,0 +1,28 @@ +* ST Microelectronics STMPE Multi-Functional Device + +STMPE is an MFD device which may expose the following inbuilt devices: gpio, +keypad, touchscreen, adc, pwm, rotator. + +Required properties: + - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - reg : I2C/SPI address of the device + +Optional properties: + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - interrupt-parent : Specifies which IRQ controller we're connected to + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + +Example: + + stmpe1601: stmpe1601@40 { + compatible = "st,stmpe1601"; + reg = <0x40>; + interrupts = <26 0x4>; + interrupt-parent = <&gpio6>; + interrupt-controller; + + wakeup-source; + st,autosleep-timeout = <1024>; + }; diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt new file mode 100644 index 00000000000..38e51ad2e07 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt @@ -0,0 +1,15 @@ +* Atmel SSC driver. + +Required properties: +- compatible: "atmel,at91rm9200-ssc" or "atmel,at91sam9g45-ssc" + - atmel,at91rm9200-ssc: support pdc transfer + - atmel,at91sam9g45-ssc: support dma transfer +- reg: Should contain SSC registers location and length +- interrupts: Should contain SSC interrupt + +Example: +ssc0: ssc@fffbc000 { + compatible = "atmel,at91rm9200-ssc"; + reg = <0xfffbc000 0x4000>; + interrupts = <14 4 5>; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8e2e0ba2f48..a591c6741d7 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -21,6 +21,12 @@ Optional properties: - cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted - max-frequency: maximum operating clock frequency +- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on + this system, even if the controller claims it is. + +Optional SDIO properties: +- keep-power-in-suspend: Preserves card power during a suspend/resume cycle +- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion Example: @@ -33,4 +39,6 @@ sdhci@ab000000 { cd-inverted; wp-gpios = <&gpio 70 0>; max-frequency = <50000000>; + keep-power-in-suspend; + enable-sdio-wakeup; } diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 630a7d7f471..97e9e315400 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -12,10 +12,6 @@ is used. The Samsung's SDHCI controller bindings extends this as listed below. [A] The property "samsung,cd-pinmux-gpio" can be used as stated in the "Optional Board Specific Properties" section below. -[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property - is not specified, it is assumed that there is no card detection - mechanism used. - Required SoC Specific Properties: - compatible: should be one of the following - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci @@ -24,14 +20,18 @@ Required SoC Specific Properties: controller. Required Board Specific Properties: -- gpios: Should specify the gpios used for clock, command and data lines. The - gpio specifier format depends on the gpio controller. +- Samsung GPIO variant (will be completely replaced by pinctrl): + - gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. +- Pinctrl variant (preferred if available): + - pinctrl-0: Should specify pin control groups used for this controller. + - pinctrl-names: Should contain only one value - "default". Optional Board Specific Properties: - samsung,cd-pinmux-gpio: Specifies the card detect line that is routed through a pinmux to the card-detect pin of the card slot. This property should be used only if none of the mmc core card-detect properties are - used. + used. Only for Samsung GPIO variant. Example: sdhci@12530000 { @@ -40,12 +40,18 @@ Example: interrupts = <0 75 0>; bus-width = <4>; cd-gpios = <&gpk2 2 2 3 3>; + + /* Samsung GPIO variant */ gpios = <&gpk2 0 2 0 3>, /* clock line */ <&gpk2 1 2 0 3>, /* command line */ <&gpk2 3 2 3 3>, /* data line 0 */ <&gpk2 4 2 3 3>, /* data line 1 */ <&gpk2 5 2 3 3>, /* data line 2 */ <&gpk2 6 2 3 3>; /* data line 3 */ + + /* Pinctrl variant */ + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>; + pinctrl-names = "default"; }; Note: This example shows both SoC specific and board specific properties diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 06cd32d0805..06cd32d0805 100644 --- a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index be76a23b34c..ed271fc255b 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -19,6 +19,7 @@ ti,dual-volt: boolean, supports dual voltage cards "supply-name" examples are "vmmc", "vmmc_aux" etc ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence +ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed Example: mmc1: mmc@0x4809c000 { diff --git a/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt new file mode 100644 index 00000000000..d7fb6abb3eb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt @@ -0,0 +1,23 @@ +* Wondermedia WM8505/WM8650 SD/MMC Host Controller + +This file documents differences between the core properties described +by mmc.txt and the properties used by the wmt-sdmmc driver. + +Required properties: +- compatible: Should be "wm,wm8505-sdhc". +- interrupts: Two interrupts are required - regular irq and dma irq. + +Optional properties: +- sdon-inverted: SD_ON bit is inverted on the controller + +Examples: + +sdhc@d800a000 { + compatible = "wm,wm8505-sdhc"; + reg = <0xd800a000 0x1000>; + interrupts = <20 21>; + clocks = <&sdhc>; + bus-width = <4>; + sdon-inverted; +}; + diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt new file mode 100644 index 00000000000..b04d03a1d49 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -0,0 +1,23 @@ +* Denali NAND controller + +Required properties: + - compatible : should be "denali,denali-nand-dt" + - reg : should contain registers location and length for data and reg. + - reg-names: Should contain the reg names "nand_data" and "denali_reg" + - interrupts : The interrupt number. + - dm-mask : DMA bit mask + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Examples: + +nand: nand@ff900000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "denali,denali-nand-dt"; + reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; + reg-names = "nand_data", "denali_reg"; + interrupts = <0 144 4>; + dma-mask = <0xffffffff>; +}; diff --git a/Documentation/devicetree/bindings/mtd/flctl-nand.txt b/Documentation/devicetree/bindings/mtd/flctl-nand.txt new file mode 100644 index 00000000000..427f46dc60a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/flctl-nand.txt @@ -0,0 +1,49 @@ +FLCTL NAND controller + +Required properties: +- compatible : "renesas,shmobile-flctl-sh7372" +- reg : Address range of the FLCTL +- interrupts : flste IRQ number +- nand-bus-width : bus width to NAND chip + +Optional properties: +- dmas: DMA specifier(s) +- dma-names: name for each DMA specifier. Valid names are + "data_tx", "data_rx", "ecc_tx", "ecc_rx" + +The DMA fields are not used yet in the driver but are listed here for +completing the bindings. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + + flctl@e6a30000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "renesas,shmobile-flctl-sh7372"; + reg = <0xe6a30000 0x100>; + interrupts = <0x0d80>; + + nand-bus-width = <16>; + + dmas = <&dmac 1 /* data_tx */ + &dmac 2;> /* data_rx */ + dma-names = "data_tx", "data_rx"; + + system@0 { + label = "system"; + reg = <0x0 0x8000000>; + }; + + userdata@8000000 { + label = "userdata"; + reg = <0x8000000 0x10000000>; + }; + + cache@18000000 { + label = "cache"; + reg = <0x18000000 0x8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index e2c663b354d..e3ea32e7de3 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -3,9 +3,7 @@ Required properties: - compatible : "st,spear600-fsmc-nand" - reg : Address range of the mtd chip -- reg-names: Should contain the reg names "fsmc_regs" and "nand_data" -- st,ale-off : Chip specific offset to ALE -- st,cle-off : Chip specific offset to CLE +- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd" Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width @@ -19,10 +17,10 @@ Example: #address-cells = <1>; #size-cells = <1>; reg = <0xd1800000 0x1000 /* FSMC Register */ - 0xd2000000 0x4000>; /* NAND Base */ - reg-names = "fsmc_regs", "nand_data"; - st,ale-off = <0x20000>; - st,cle-off = <0x10000>; + 0xd2000000 0x0010 /* NAND Base DATA */ + 0xd2020000 0x0010 /* NAND Base ADDR */ + 0xd2010000 0x0010>; /* NAND Base CMD */ + reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd"; bank-width = <1>; nand-skip-bbtscan; diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt new file mode 100644 index 00000000000..6d3d5760947 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/m25p80.txt @@ -0,0 +1,29 @@ +* MTD SPI driver for ST M25Pxx (and similar) serial flash chips + +Required properties: +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- compatible : Should be the manufacturer and the name of the chip. Bear in mind + the DT binding is not Linux-only, but in case of Linux, see the + "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of + supported chips. +- reg : Chip-Select number +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at + +Optional properties: +- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead + of the usual "read" opcode. This opcode is not supported by + all chips and support for it can not be detected at runtime. + Refer to your chips' datasheet to check if this is supported + by your chip. + +Example: + + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + reg = <0>; + spi-max-frequency = <40000000>; + m25p,fast-read; + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 94de19b8f16..dab7847fc80 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -23,6 +23,9 @@ file systems on embedded devices. unaligned accesses as implemented in the JFFS2 code via memcpy(). By defining "no-unaligned-direct-access", the flash will not be exposed directly to the MTD users (e.g. JFFS2) any more. + - linux,mtd-name: allow to specify the mtd name for retro capability with + physmap-flash drivers as boot loader pass the mtd partition via the old + device name physmap-flash. For JEDEC compatible devices, the following additional properties are defined: diff --git a/Documentation/devicetree/bindings/net/can/grcan.txt b/Documentation/devicetree/bindings/net/can/grcan.txt new file mode 100644 index 00000000000..34ef3498f88 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/grcan.txt @@ -0,0 +1,28 @@ +Aeroflex Gaisler GRCAN and GRHCAN CAN controllers. + +The GRCAN and CRHCAN CAN controllers are available in the GRLIB VHDL IP core +library. + +Note: These properties are built from the AMBA plug&play in a Leon SPARC system +(the ordinary environment for GRCAN and GRHCAN). There are no dts files for +sparc. + +Required properties: + +- name : Should be "GAISLER_GRCAN", "01_03d", "GAISLER_GRHCAN" or "01_034" + +- reg : Address and length of the register set for the device + +- freq : Frequency of the external oscillator clock in Hz (the frequency of + the amba bus in the ordinary case) + +- interrupts : Interrupt number for this device + +Optional properties: + +- systemid : If not present or if the value of the least significant 16 bits + of this 32-bit property is smaller than GRCAN_TXBUG_SAFE_GRLIB_VERSION + a bug workaround is activated. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt new file mode 100644 index 00000000000..09055c2495f --- /dev/null +++ b/Documentation/devicetree/bindings/net/cdns-emac.txt @@ -0,0 +1,23 @@ +* Cadence EMAC Ethernet controller + +Required properties: +- compatible: Should be "cdns,[<chip>-]{emac}" + Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. + or the generic form: "cdns,emac". +- reg: Address and length of the register set for the device +- interrupts: Should contain macb interrupt +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "mii", "rmii". + +Optional properties: +- local-mac-address: 6 bytes, mac address + +Examples: + + macb0: ethernet@fffc4000 { + compatible = "cdns,at91rm9200-emac"; + reg = <0xfffc4000 0x4000>; + interrupts = <21>; + phy-mode = "rmii"; + local-mac-address = [3a 0e 03 04 05 06]; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index dcaabe9fe86..6ddd0286a9b 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -9,21 +9,15 @@ Required properties: number - interrupt-parent : The parent interrupt controller - cpdma_channels : Specifies number of channels in CPDMA -- host_port_no : Specifies host port shift -- cpdma_reg_ofs : Specifies CPDMA submodule register offset -- cpdma_sram_ofs : Specifies CPDMA SRAM offset -- ale_reg_ofs : Specifies ALE submodule register offset - ale_entries : Specifies No of entries ALE can hold -- host_port_reg_ofs : Specifies host port register offset -- hw_stats_reg_ofs : Specifies hardware statistics register offset -- bd_ram_ofs : Specifies internal desciptor RAM offset - bd_ram_size : Specifies internal descriptor RAM size - rx_descs : Specifies number of Rx descriptors - mac_control : Specifies Default MAC control register content for the specific platform - slaves : Specifies number for slaves -- slave_reg_ofs : Specifies slave register offset -- sliver_reg_ofs : Specifies slave sliver register offset +- cpts_active_slave : Specifies the slave to use for time stamping +- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds +- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds - phy_id : Specifies slave phy id - mac-address : Specifies slave MAC address @@ -45,30 +39,22 @@ Examples: interrupts = <55 0x4>; interrupt-parent = <&intc>; cpdma_channels = <8>; - host_port_no = <0>; - cpdma_reg_ofs = <0x800>; - cpdma_sram_ofs = <0xa00>; - ale_reg_ofs = <0xd00>; ale_entries = <1024>; - host_port_reg_ofs = <0x108>; - hw_stats_reg_ofs = <0x900>; - bd_ram_ofs = <0x2000>; bd_ram_size = <0x2000>; no_bd_ram = <0>; rx_descs = <64>; mac_control = <0x20>; slaves = <2>; + cpts_active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; cpsw_emac0: slave@0 { - slave_reg_ofs = <0x208>; - sliver_reg_ofs = <0xd80>; - phy_id = "davinci_mdio.16:00"; + phy_id = <&davinci_mdio>, <0>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { - slave_reg_ofs = <0x308>; - sliver_reg_ofs = <0xdc0>; - phy_id = "davinci_mdio.16:01"; + phy_id = <&davinci_mdio>, <1>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; @@ -79,30 +65,22 @@ Examples: compatible = "ti,cpsw"; ti,hwmods = "cpgmac0"; cpdma_channels = <8>; - host_port_no = <0>; - cpdma_reg_ofs = <0x800>; - cpdma_sram_ofs = <0xa00>; - ale_reg_ofs = <0xd00>; ale_entries = <1024>; - host_port_reg_ofs = <0x108>; - hw_stats_reg_ofs = <0x900>; - bd_ram_ofs = <0x2000>; bd_ram_size = <0x2000>; no_bd_ram = <0>; rx_descs = <64>; mac_control = <0x20>; slaves = <2>; + cpts_active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; cpsw_emac0: slave@0 { - slave_reg_ofs = <0x208>; - sliver_reg_ofs = <0xd80>; - phy_id = "davinci_mdio.16:00"; + phy_id = <&davinci_mdio>, <0>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { - slave_reg_ofs = <0x308>; - sliver_reg_ofs = <0xdc0>; - phy_id = "davinci_mdio.16:01"; + phy_id = <&davinci_mdio>, <1>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt new file mode 100644 index 00000000000..859a6fa7569 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -0,0 +1,23 @@ +* Marvell Armada 370 / Armada XP Ethernet Controller (NETA) + +Required properties: +- compatible: should be "marvell,armada-370-neta". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device +- phy: A phandle to a phy node defining the PHY address (as the reg + property, a single integer). +- phy-mode: The interface between the SoC and the PHY (a string that + of_get_phy_mode() can understand) +- clocks: a pointer to the reference clock for this device. + +Example: + +ethernet@d0070000 { + compatible = "marvell,armada-370-neta"; + reg = <0xd0070000 0x2500>; + interrupts = <8>; + clocks = <&gate_clk 4>; + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt new file mode 100644 index 00000000000..34e7aafa321 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt @@ -0,0 +1,35 @@ +* Marvell MDIO Ethernet Controller interface + +The Ethernet controllers of the Marvel Kirkwood, Dove, Orion5x, +MV78xx0, Armada 370 and Armada XP have an identical unit that provides +an interface with the MDIO bus. This driver handles this MDIO +interface. + +Required properties: +- compatible: "marvell,orion-mdio" +- reg: address and length of the SMI register + +The child nodes of the MDIO driver are the individual PHY devices +connected to this MDIO bus. They must have a "reg" property given the +PHY address on the MDIO bus. + +Example at the SoC level: + +mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0xd0072004 0x4>; +}; + +And at the board level: + +mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +} diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt new file mode 100644 index 00000000000..3a268127b05 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -0,0 +1,141 @@ +* Atmel AT91 Pinmux Controller + +The AT91 Pinmux Controler, enables the IC +to share one PAD to several functional blocks. The sharing is done by +multiplexing the PAD input/output signals. For each PAD there are up to +8 muxing options (called periph modes). Since different modules require +different PAD settings (like pull up, keeper, etc) the contoller controls +also the PAD settings parameters. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Atmel AT91 pin configuration node is a node of a group of pins which can be +used for a specific device or function. This node represents both mux and config +of the pins in that group. The 'pins' selects the function mode(also named pin +mode) this pin can work on and the 'config' configures various pad settings +such as pull-up, multi drive, etc. + +Required properties for iomux controller: +- compatible: "atmel,at91rm9200-pinctrl" +- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be + configured in this periph mode. All the periph and bank need to be describe. + +How to create such array: + +Each column will represent the possible peripheral of the pinctrl +Each line will represent a pio bank + +Take an example on the 9260 +Peripheral: 2 ( A and B) +Bank: 3 (A, B and C) +=> + + /* A B */ + 0xffffffff 0xffc00c3b /* pioA */ + 0xffffffff 0x7fff3ccf /* pioB */ + 0xffffffff 0x007fffff /* pioC */ + +For each peripheral/bank we will descibe in a u32 if a pin can can be +configured in it by putting 1 to the pin bit (1 << pin) + +Let's take the pioA on peripheral B +From the datasheet Table 10-2. +Peripheral B +PA0 MCDB0 +PA1 MCCDB +PA2 +PA3 MCDB3 +PA4 MCDB2 +PA5 MCDB1 +PA6 +PA7 +PA8 +PA9 +PA10 ETX2 +PA11 ETX3 +PA12 +PA13 +PA14 +PA15 +PA16 +PA17 +PA18 +PA19 +PA20 +PA21 +PA22 ETXER +PA23 ETX2 +PA24 ETX3 +PA25 ERX2 +PA26 ERX3 +PA27 ERXCK +PA28 ECRS +PA29 ECOL +PA30 RXD4 +PA31 TXD4 + +=> 0xffc00c3b + +Required properties for pin configuration node: +- atmel,pins: 4 integers array, represents a group of pins mux and config + setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>. + The PERIPH 0 means gpio. + +Bits used for CONFIG: +PULL_UP (1 << 0): indicate this pin need a pull up. +MULTIDRIVE (1 << 1): indicate this pin need to be configured as multidrive. +DEGLITCH (1 << 2): indicate this pin need deglitch. +PULL_DOWN (1 << 3): indicate this pin need a pull down. +DIS_SCHMIT (1 << 4): indicate this pin need to disable schmit trigger. +DEBOUNCE (1 << 16): indicate this pin need debounce. +DEBOUNCE_VAL (0x3fff << 17): debounce val. + +NOTE: +Some requirements for using atmel,at91rm9200-pinctrl binding: +1. We have pin function node defined under at91 controller node to represent + what pinmux functions this SoC supports. +2. The driver can use the function node's name and pin configuration node's + name describe the pin function and group hierarchy. + For example, Linux at91 pinctrl driver takes the function node's name + as the function name and pin configuration node's name as group name to + create the map table. +3. Each pin configuration node should have a phandle, devices can set pins + configurations by referring to the phandle of that pin configuration node. +4. The gpio controller must be describe in the pinctrl simple-bus. + +Examples: + +pinctrl@fffff400 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + reg = <0xfffff400 0x600>; + + atmel,mux-mask = < + /* A B */ + 0xffffffff 0xffc00c3b /* pioA */ + 0xffffffff 0x7fff3ccf /* pioB */ + 0xffffffff 0x007fffff /* pioC */ + >; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <1 14 0x1 0x0 /* PB14 periph A */ + 1 15 0x1 0x1>; /* PB15 periph with pullup */ + }; + }; +}; + +dbgu: serial@fffff200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt index 361bccb7ec8..95daf6335c3 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt @@ -7,8 +7,10 @@ Required properties: - compatible: "marvell,88f6180-pinctrl", "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl", "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl" + "marvell,98dx4122-pinctrl" This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x. +It also support the 88f6281-based variant in the 98dx412x Bobcat SoCs. Available mpp pins/groups and functions: Note: brackets (x) are not part of the mpp name for marvell,function and given @@ -277,3 +279,40 @@ mpp46 46 gpio, ts(mp10), tdm(fs), lcd(hsync) mpp47 47 gpio, ts(mp11), tdm(drx), lcd(vsync) mpp48 48 gpio, ts(mp12), tdm(dtx), lcd(d16) mpp49 49 gpo, tdm(rx0ql), pex(clkreq), lcd(d17) + +* Marvell Bobcat 98dx4122 + +name pins functions +================================================================================ +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd) +mpp5 5 gpo, nand(io7), uart0(txd) +mpp6 6 sysrst(out), spi(mosi) +mpp7 7 gpo, pex(rsto), spi(cs) +mpp8 8 gpio, twsi0(sda), uart0(rts), uart1(rts) +mpp9 9 gpio, twsi(sck), uart0(cts), uart1(cts) +mpp10 10 gpo, spi(sck), uart0(txd) +mpp11 11 gpio, spi(miso), uart0(rxd) +mpp13 13 gpio, uart1(txd) +mpp14 14 gpio, uart1(rxd) +mpp15 15 gpio, uart0(rts) +mpp16 16 gpio, uart0(cts) +mpp18 18 gpo, nand(io0) +mpp19 19 gpo, nand(io1) +mpp34 34 gpio +mpp35 35 gpio +mpp36 36 gpio +mpp37 37 gpio +mpp38 38 gpio +mpp39 39 gpio +mpp40 40 gpio +mpp41 41 gpio +mpp42 42 gpio +mpp43 43 gpio +mpp44 44 gpio +mpp45 45 gpio +mpp49 49 gpio + diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index 03dee50532f..e97a27856b2 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -8,13 +8,20 @@ on-chip controllers onto these pads. Required Properties: - compatible: should be one of the following. - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller. + - "samsung,pinctrl-exynos4x12": for Exynos4x12 compatible pin-controller. - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of the address space it occupies. -- interrupts: interrupt specifier for the controller. The format and value of - the interrupt specifier depends on the interrupt parent for the controller. +- Pin banks as child nodes: Pin banks of the controller are represented by child + nodes of the controller node. Bank name is taken from name of the node. Each + bank node must contain following properties: + + - gpio-controller: identifies the node as a gpio controller and pin bank. + - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO + binding is used, the amount of cells must be specified as 2. See generic + GPIO binding documentation for description of particular cells. - Pin mux/config groups as child nodes: The pin mux (selecting pin function mode) and pin config (pull up/down, driver strength) settings are represented @@ -72,16 +79,24 @@ used as system wakeup events. A. External GPIO Interrupts: For supporting external gpio interrupts, the following properties should be specified in the pin-controller device node. -- interrupt-controller: identifies the controller node as interrupt-parent. -- #interrupt-cells: the value of this property should be 2. - - First Cell: represents the external gpio interrupt number local to the - external gpio interrupt space of the controller. - - Second Cell: flags to identify the type of the interrupt - - 1 = rising edge triggered - - 2 = falling edge triggered - - 3 = rising and falling edge triggered - - 4 = high level triggered - - 8 = low level triggered + - interrupt-parent: phandle of the interrupt parent to which the external + GPIO interrupts are forwarded to. + - interrupts: interrupt specifier for the controller. The format and value of + the interrupt specifier depends on the interrupt parent for the controller. + + In addition, following properties must be present in node of every bank + of pins supporting GPIO interrupts: + + - interrupt-controller: identifies the controller node as interrupt-parent. + - #interrupt-cells: the value of this property should be 2. + - First Cell: represents the external gpio interrupt number local to the + external gpio interrupt space of the controller. + - Second Cell: flags to identify the type of the interrupt + - 1 = rising edge triggered + - 2 = falling edge triggered + - 3 = rising and falling edge triggered + - 4 = high level triggered + - 8 = low level triggered B. External Wakeup Interrupts: For supporting external wakeup interrupts, a child node representing the external wakeup interrupt controller should be @@ -94,6 +109,11 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a found on Samsung Exynos4210 SoC. - interrupt-parent: phandle of the interrupt parent to which the external wakeup interrupts are forwarded to. + - interrupts: interrupt used by multiplexed wakeup interrupts. + + In addition, following properties must be present in node of every bank + of pins supporting wake-up interrupts: + - interrupt-controller: identifies the node as interrupt-parent. - #interrupt-cells: the value of this property should be 2 - First Cell: represents the external wakeup interrupt number local to @@ -105,11 +125,63 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a - 4 = high level triggered - 8 = low level triggered + Node of every bank of pins supporting direct wake-up interrupts (without + multiplexing) must contain following properties: + + - interrupt-parent: phandle of the interrupt parent to which the external + wakeup interrupts are forwarded to. + - interrupts: interrupts of the interrupt parent which are used for external + wakeup interrupts from pins of the bank, must contain interrupts for all + pins of the bank. + Aliases: All the pin controller nodes should be represented in the aliases node using the following format 'pinctrl{n}' where n is a unique number for the alias. +Example: A pin-controller node with pin banks: + + pinctrl_0: pinctrl@11400000 { + compatible = "samsung,pinctrl-exynos4210"; + reg = <0x11400000 0x1000>; + interrupts = <0 47 0>; + + /* ... */ + + /* Pin bank without external interrupts */ + gpy0: gpy0 { + gpio-controller; + #gpio-cells = <2>; + }; + + /* ... */ + + /* Pin bank with external GPIO or muxed wake-up interrupts */ + gpj0: gpj0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + /* ... */ + + /* Pin bank with external direct wake-up interrupts */ + gpx0: gpx0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + interrupt-parent = <&gic>; + interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>, + <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>; + #interrupt-cells = <2>; + }; + + /* ... */ + }; + Example 1: A pin-controller node with pin groups. pinctrl_0: pinctrl@11400000 { @@ -117,6 +189,8 @@ Example 1: A pin-controller node with pin groups. reg = <0x11400000 0x1000>; interrupts = <0 47 0>; + /* ... */ + uart0_data: uart0-data { samsung,pins = "gpa0-0", "gpa0-1"; samsung,pin-function = <2>; @@ -158,20 +232,14 @@ Example 2: A pin-controller node with external wakeup interrupt controller node. pinctrl_1: pinctrl@11000000 { compatible = "samsung,pinctrl-exynos4210"; reg = <0x11000000 0x1000>; - interrupts = <0 46 0>; - interrupt-controller; - #interrupt-cells = <2>; + interrupts = <0 46 0> - wakup_eint: wakeup-interrupt-controller { + /* ... */ + + wakeup-interrupt-controller { compatible = "samsung,exynos4210-wakeup-eint"; interrupt-parent = <&gic>; - interrupt-controller; - #interrupt-cells = <2>; - interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>, - <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>, - <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>, - <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>, - <0 32 0>; + interrupts = <0 32 0>; }; }; @@ -190,7 +258,8 @@ Example 4: Set up the default pin state for uart controller. static int s3c24xx_serial_probe(struct platform_device *pdev) { struct pinctrl *pinctrl; - ... - ... + + /* ... */ + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); } diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt new file mode 100644 index 00000000000..0ba1bcc7f33 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt @@ -0,0 +1,16 @@ +=== AB8500 Battery Temperature Monitor Driver === + +The properties below describes the node for btemp driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-btemp" +- battery = Shall be battery specific information + + Example: + ab8500_btemp { + compatible = "stericsson,ab8500-btemp"; + battery = <&ab8500_battery>; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt new file mode 100644 index 00000000000..ef532837112 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt @@ -0,0 +1,16 @@ +=== AB8500 Charging Algorithm Driver === + +The properties below describes the node for chargalg driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-chargalg" +- battery = Shall be battery specific information + +Example: +ab8500_chargalg { + compatible = "stericsson,ab8500-chargalg"; + battery = <&ab8500_battery>; +}; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt new file mode 100644 index 00000000000..6bdbb08ea9e --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt @@ -0,0 +1,25 @@ +=== AB8500 Charger Driver === + +Required Properties: +- compatible = Shall be "stericsson,ab8500-charger" +- battery = Shall be battery specific information + Example: + ab8500_charger { + compatible = "stericsson,ab8500-charger"; + battery = <&ab8500_battery>; + }; + +- vddadc-supply: Supply for USB and Main charger + Example: + ab8500-charger { + vddadc-supply = <&ab8500_ldo_tvout_reg>; + } +- autopower_cfg: + Boolean value depicting the presence of 'automatic poweron after powerloss' + Example: + ab8500-charger { + autopower_cfg; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt new file mode 100644 index 00000000000..ccafcb9112f --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt @@ -0,0 +1,58 @@ +=== AB8500 Fuel Gauge Driver === + +AB8500 is a mixed signal multimedia and power management +device comprising: power and energy-management-module, +wall-charger, usb-charger, audio codec, general purpose adc, +tvout, clock management and sim card interface. + +Fuelgauge support is part of energy-management-modules, other +components of this module are: +main-charger, usb-combo-charger and battery-temperature-monitoring. + +The properties below describes the node for fuelgauge driver. + +Required Properties: +- compatible = This shall be: "stericsson,ab8500-fg" +- battery = Shall be battery specific information + Example: + ab8500_fg { + compatible = "stericsson,ab8500-fg"; + battery = <&ab8500_battery>; + }; + +dependent node: + ab8500_battery: ab8500_battery { + }; + This node will provide information on 'thermistor interface' and + 'battery technology type' used. + +Properties of this node are: +thermistor-on-batctrl: + A boolean value indicating thermistor interface to battery + + Note: + 'btemp' and 'batctrl' are the pins interfaced for battery temperature + measurement, 'btemp' signal is used when NTC(negative temperature + coefficient) resister is interfaced external to battery whereas + 'batctrl' pin is used when NTC resister is internal to battery. + + Example: + ab8500_battery: ab8500_battery { + thermistor-on-batctrl; + }; + indicates: NTC resister is internal to battery, 'batctrl' is used + for thermal measurement. + + The absence of property 'thermal-on-batctrl' indicates + NTC resister is external to battery and 'btemp' signal is used + for thermal measurement. + +battery-type: + This shall be the battery manufacturing technology type, + allowed types are: + "UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn" + Example: + ab8500_battery: ab8500_battery { + stericsson,battery-type = "LIPO"; + } + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt new file mode 100644 index 00000000000..4ad29b9ac2a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt @@ -0,0 +1,81 @@ +* Freescale 85xx RAID Engine nodes + +RAID Engine nodes are defined to describe on-chip RAID accelerators. Each RAID +Engine should have a separate node. + +Supported chips: +P5020, P5040 + +Required properties: + +- compatible: Should contain "fsl,raideng-v1.0" as the value + This identifies RAID Engine block. 1 in 1.0 represents + major number whereas 0 represents minor number. The + version matches the hardware IP version. +- reg: offset and length of the register set for the device +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng: raideng@320000 { + compatible = "fsl,raideng-v1.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x320000 0x10000>; + ranges = <0 0x320000 0x10000>; + }; + + +There must be a sub-node for each job queue present in RAID Engine +This node must be a sub-node of the main RAID Engine node + +- compatible: Should contain "fsl,raideng-v1.0-job-queue" as the value + This identifies the job queue interface +- reg: offset and length of the register set for job queue +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + }; + + +There must be a sub-node for each job ring present in RAID Engine +This node must be a sub-node of job queue node + +- compatible: Must contain "fsl,raideng-v1.0-job-ring" as the value + This identifies job ring. Should contain either + "fsl,raideng-v1.0-hp-ring" or "fsl,raideng-v1.0-lp-ring" + depending upon whether ring has high or low priority +- reg: offset and length of the register set for job ring +- interrupts: interrupt mapping for job ring IRQ + +Optional property: + +- fsl,liodn: Specifies the LIODN to be used for Job Ring. This + property is normally set by firmware. Value + is of 12-bits which is the LIODN number for this JR. + This property is used by the IOMMU (PAMU) to distinquish + transactions from this JR and than be able to do address + translation & protection accordingly. + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + + raideng_jr0: jr@0 { + compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-hp-ring"; + reg = <0x0 0x400>; + interrupts = <139 2 0 0>; + interrupt-parent = <&mpic>; + fsl,liodn = <0x41>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt new file mode 100644 index 00000000000..131e8c11d26 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -0,0 +1,23 @@ +TI SOC ECAP based APWM controller + +Required properties: +- compatible: Must be "ti,am33xx-ecap" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the ECAP: + "ecap<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ecap0: ecap@0 { + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt new file mode 100644 index 00000000000..4fc7079d822 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -0,0 +1,23 @@ +TI SOC EHRPWM based PWM controller + +Required properties: +- compatible : Must be "ti,am33xx-ehrpwm" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the EHRPWM: + "ehrpwm<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ehrpwm0: ehrpwm@0 { + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x100>; + ti,hwmods = "ehrpwm0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt new file mode 100644 index 00000000000..f7eae77f835 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -0,0 +1,31 @@ +TI SOC based PWM Subsystem + +Required properties: +- compatible: Must be "ti,am33xx-pwmss"; +- reg: physical base address and size of the registers map. +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. +- ranges: describes the address mapping of a memory-mapped bus. Should set to + physical address map of child's base address, physical address within + parent's address space and length of the address map. For am33xx, + 3 set of child register maps present, ECAP register space, EQEP + register space, EHRPWM register space. + +Also child nodes should also populated under PWMSS DT node. + +Example: +pwmss0: pwmss@48300000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt index 73ec962bfe8..06e67247859 100644 --- a/Documentation/devicetree/bindings/pwm/pwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm.txt @@ -37,10 +37,21 @@ device: pwm-names = "backlight"; }; +Note that in the example above, specifying the "pwm-names" is redundant +because the name "backlight" would be used as fallback anyway. + pwm-specifier typically encodes the chip-relative PWM number and the PWM -period in nanoseconds. Note that in the example above, specifying the -"pwm-names" is redundant because the name "backlight" would be used as -fallback anyway. +period in nanoseconds. + +Optionally, the pwm-specifier can encode a number of flags in a third cell: +- bit 0: PWM signal polarity (0: normal polarity, 1: inverse polarity) + +Example with optional PWM specifier for inverse polarity + + bl: backlight { + pwms = <&pwm 0 5000000 1>; + pwm-names = "backlight"; + }; 2) PWM controller nodes ----------------------- diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt new file mode 100644 index 00000000000..3ac779d8338 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt @@ -0,0 +1,18 @@ +== ST SPEAr SoC PWM controller == + +Required properties: +- compatible: should be one of: + - "st,spear320-pwm" + - "st,spear1340-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: number of cells used to specify PWM which is fixed to 2 on + SPEAr. The first cell specifies the per-chip index of the PWM to use and + the second cell is the period in nanoseconds. + +Example: + + pwm: pwm@a8000000 { + compatible ="st,spear320-pwm"; + reg = <0xa8000000 0x1000>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt new file mode 100644 index 00000000000..2943ee5fce0 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers + +Supported PWMs: +On TWL4030 series: PWM1 and PWM2 +On TWL6030 series: PWM0 and PWM1 + +Required properties: +- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwm: pwm { + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt new file mode 100644 index 00000000000..cb64f3acc10 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers connected to LED terminals + +Supported PWMs: +On TWL4030 series: PWMA and PWMB (connected to LEDA and LEDB terminals) +On TWL6030 series: LED PWM (mainly used as charging indicator LED) + +Required properties: +- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwmled: pwmled { + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt new file mode 100644 index 00000000000..bcc63678a9a --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -0,0 +1,17 @@ +VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller + +Required properties: +- compatible: should be "via,vt8500-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. +- clocks: phandle to the PWM source clock + +Example: + +pwm1: pwm@d8220000 { + #pwm-cells = <2>; + compatible = "via,vt8500-pwm"; + reg = <0xd8220000 0x1000>; + clocks = <&clkpwm>; +}; diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt new file mode 100644 index 00000000000..63c659800c0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt @@ -0,0 +1,37 @@ +GPIO controlled regulators + +Required properties: +- compatible : Must be "regulator-gpio". +- states : Selection of available voltages and GPIO configs. + if there are no states, then use a fixed regulator + +Optional properties: +- enable-gpio : GPIO to use to enable/disable the regulator. +- gpios : GPIO group used to control voltage. +- startup-delay-us : Startup time in microseconds. +- enable-active-high : Polarity of GPIO is active high (default is low). + +Any property defined as part of the core regulator binding defined in +regulator.txt can also be used. + +Example: + + mmciv: gpio-regulator { + compatible = "regulator-gpio"; + + regulator-name = "mmci-gpio-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2600000>; + regulator-boot-on; + + enable-gpio = <&gpio0 23 0x4>; + gpios = <&gpio0 24 0x4 + &gpio0 25 0x4>; + states = <1800000 0x3 + 2200000 0x2 + 2600000 0x1 + 2900000 0x0>; + + startup-delay-us = <100000>; + enable-active-high; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8925-regulator.txt b/Documentation/devicetree/bindings/regulator/max8925-regulator.txt new file mode 100644 index 00000000000..0057695aae8 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8925-regulator.txt @@ -0,0 +1,40 @@ +Max8925 Voltage regulators + +Required nodes: +-nodes: + - SDV1 for SDV SDV1 + - SDV2 for SDV SDV2 + - SDV3 for SDV SDV3 + - LDO1 for LDO LDO1 + - LDO2 for LDO LDO2 + - LDO3 for LDO LDO3 + - LDO4 for LDO LDO4 + - LDO5 for LDO LDO5 + - LDO6 for LDO LDO6 + - LDO7 for LDO LDO7 + - LDO8 for LDO LDO8 + - LDO9 for LDO LDO9 + - LDO10 for LDO LDO10 + - LDO11 for LDO LDO11 + - LDO12 for LDO LDO12 + - LDO13 for LDO LDO13 + - LDO14 for LDO LDO14 + - LDO15 for LDO LDO15 + - LDO16 for LDO LDO16 + - LDO17 for LDO LDO17 + - LDO18 for LDO LDO18 + - LDO19 for LDO LDO19 + - LDO20 for LDO LDO20 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt new file mode 100644 index 00000000000..9fd69a18b0b --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt @@ -0,0 +1,146 @@ +* Maxim MAX8997 Voltage and Current Regulator + +The Maxim MAX8997 is a multi-function device which includes volatage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of max8997. + +Required properties: +- compatible: Should be "maxim,max8997-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- max8997,pmic-buck1-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck1 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- max8997,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- max8997,pmic-buck5-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck5 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +[1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional + property is specified, the 'max8997,pmic-buck[1/2/5]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional + property is specified, then all the eigth voltage values for the + 'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from max8997 are delivered to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- max8997,pmic-buck1-uses-gpio-dvs: 'buck1' can be controlled by gpio dvs. +- max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- max8997,pmic-buck5-uses-gpio-dvs: 'buck5' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: +- max8997,pmic-ignore-gpiodvs-side-effect: When GPIO-DVS mode is used for + multiple bucks, changing the voltage value of one of the bucks may affect + that of another buck, which is the side effect of the change (set_voltage). + Use this property to ignore such side effects and change the voltage. + +- max8997,pmic-buck125-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- max8997,pmic-buck125-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of max8997 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + standard regulator bindings here + }; + +The following are the names of the regulators that the max8997 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of max8997. + + - LDOn + - valid values for n are 1 to 18 and 21 + - Example: LDO0, LD01, LDO2, LDO21 + - BUCKn + - valid values for n are 1 to 7. + - Example: BUCK1, BUCK2, BUCK3, BUCK7 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + + - CHARGER_CV: main battery charger voltage control + - CHARGER: main battery charger current control + - CHARGER_TOPOFF: end of charge current threshold level + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + max8997_pmic@66 { + compatible = "maxim,max8997-pmic"; + interrupt-parent = <&wakeup_eint>; + reg = <0x66>; + interrupts = <4 0>, <3 0>; + + max8997,pmic-buck1-uses-gpio-dvs; + max8997,pmic-buck2-uses-gpio-dvs; + max8997,pmic-buck5-uses-gpio-dvs; + + max8997,pmic-ignore-gpiodvs-side-effect; + max8997,pmic-buck125-default-dvs-idx = <0>; + + max8997,pmic-buck125-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>, /* SET2 */ + <&gpx0 2 1 0 0>; /* SET3 */ + + max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + max8997,pmic-buck2-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index d316fb895da..4f05d208c95 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -11,6 +11,9 @@ Required properties: using the standard binding for regulators found at Documentation/devicetree/bindings/regulator/regulator.txt. +Optional properties: +- ti,pmic-shutdown-controller: Telling the PMIC to shutdown on PWR_EN toggle. + The valid names for regulators are: tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4 @@ -20,6 +23,7 @@ Example: tps: tps@24 { compatible = "ti,tps65217"; + ti,pmic-shutdown-controller; regulators { dcdc1_reg: dcdc1 { diff --git a/Documentation/devicetree/bindings/regulator/vexpress.txt b/Documentation/devicetree/bindings/regulator/vexpress.txt new file mode 100644 index 00000000000..d775f72487a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/vexpress.txt @@ -0,0 +1,32 @@ +Versatile Express voltage regulators +------------------------------------ + +Requires node properties: +- "compatible" value: "arm,vexpress-volt" +- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg + (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt + for more details) + +Required regulator properties: +- "regulator-name" +- "regulator-always-on" + +Optional regulator properties: +- "regulator-min-microvolt" +- "regulator-max-microvolt" + +See Documentation/devicetree/bindings/regulator/regulator.txt +for more details about the regulator properties. + +When no "regulator-[min|max]-microvolt" properties are defined, +the device is treated as fixed (or rather "read-only") regulator. + +Example: + volt@0 { + compatible = "arm,vexpress-volt"; + arm,vexpress-sysreg,func = <2 0>; + regulator-name = "Cores"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + }; diff --git a/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt new file mode 100644 index 00000000000..c9d80d7da14 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt @@ -0,0 +1,17 @@ +* i.MX25 Real Time Clock controller + +This binding supports the following chips: i.MX25, i.MX53 + +Required properties: +- compatible: should be: "fsl,imx25-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: rtc alarm interrupt + +Example: + +rtc@80056000 { + compatible = "fsl,imx53-rtc", "fsl,imx25-rtc"; + reg = <0x80056000 2000>; + interrupts = <29>; +}; diff --git a/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt new file mode 100644 index 00000000000..93f45e9dce7 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt @@ -0,0 +1,19 @@ +NVIDIA Tegra20 real-time clock + +The Tegra RTC maintains seconds and milliseconds counters, and five alarm +registers. The alarms and other interrupts may wake the system from low-power +state. + +Required properties: + +- compatible : should be "nvidia,tegra20-rtc". +- reg : Specifies base physical address and size of the registers. +- interrupts : A single interrupt specifier. + +Example: + +timer { + compatible = "nvidia,tegra20-rtc"; + reg = <0x7000e000 0x100>; + interrupts = <0 2 0x04>; +}; diff --git a/Documentation/devicetree/bindings/rtc/orion-rtc.txt b/Documentation/devicetree/bindings/rtc/orion-rtc.txt new file mode 100644 index 00000000000..3bf63ffa516 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/orion-rtc.txt @@ -0,0 +1,18 @@ +* Mvebu Real Time Clock + +RTC controller for the Kirkwood, the Dove, the Armada 370 and the +Armada XP SoCs + +Required properties: +- compatible : Should be "marvell,orion-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: IRQ line for the RTC. + +Example: + +rtc@10300 { + compatible = "marvell,orion-rtc"; + reg = <0xd0010300 0x20>; + interrupts = <50>; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/Documentation/devicetree/bindings/rtc/rtc-omap.txt new file mode 100644 index 00000000000..b47aa415c82 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-omap.txt @@ -0,0 +1,17 @@ +TI Real Time Clock + +Required properties: +- compatible: "ti,da830-rtc" +- reg: Address range of rtc register set +- interrupts: rtc timer, alarm interrupts in order +- interrupt-parent: phandle for the interrupt controller + +Example: + +rtc@1c23000 { + compatible = "ti,da830-rtc"; + reg = <0x23000 0x1000>; + interrupts = <19 + 19>; + interrupt-parent = <&intc>; +}; diff --git a/Documentation/devicetree/bindings/sound/ak4104.txt b/Documentation/devicetree/bindings/sound/ak4104.txt new file mode 100644 index 00000000000..b902ee39cf8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ak4104.txt @@ -0,0 +1,22 @@ +AK4104 S/PDIF transmitter + +This device supports SPI mode only. + +Required properties: + + - compatible : "asahi-kasei,ak4104" + + - reg : The chip select number on the SPI bus + +Optional properties: + + - reset-gpio : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the device starts. + +Example: + +spdif: ak4104@0 { + compatible = "asahi-kasei,ak4104"; + reg = <0>; + spi-max-frequency = <5000000>; +}; diff --git a/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt b/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt new file mode 100644 index 00000000000..9c5a9947b64 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt @@ -0,0 +1,26 @@ +* Atmel at91sam9g20ek wm8731 audio complex + +Required properties: + - compatible: "atmel,at91sam9g20ek-wm8731-audio" + - atmel,model: The user-visible name of this sound complex. + - atmel,audio-routing: A list of the connections between audio components. + - atmel,ssc-controller: The phandle of the SSC controller + - atmel,audio-codec: The phandle of the WM8731 audio codec +Optional properties: + - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt + +Example: +sound { + compatible = "atmel,at91sam9g20ek-wm8731-audio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_mck>; + + atmel,model = "wm8731 @ AT91SAMG20EK"; + + atmel,audio-routing = + "Ext Spk", "LHPOUT", + "Int MIC", "MICIN"; + + atmel,ssc-controller = <&ssc0>; + atmel,audio-codec = <&wm8731>; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index c81b5fd5a5b..a850fb9c88e 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -18,6 +18,8 @@ Optional properties: - reset-gpio: a GPIO spec to define which pin is connected to the chip's !RESET pin + - cirrus,amuteb-eq-bmutec: When given, the Codec's AMUTEB=BMUTEC flag + is enabled. Examples: diff --git a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt index 65dec876cb2..fd40c852d7c 100644 --- a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt +++ b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt @@ -12,7 +12,7 @@ Required properties: Optional properties: - ti,dmic: phandle for the OMAP dmic node if the machine have it connected -- ti,jack_detection: Need to be set to <1> if the board capable to detect jack +- ti,jack_detection: Need to be present if the board capable to detect jack insertion, removal. Available audio endpoints for the audio-routing table: @@ -59,7 +59,7 @@ sound { compatible = "ti,abe-twl6040"; ti,model = "SDP4430"; - ti,jack-detection = <1>; + ti,jack-detection; ti,mclk-freq = <38400000>; ti,mcpdm = <&mcpdm>; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt new file mode 100644 index 00000000000..7b53da5cb75 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt @@ -0,0 +1,26 @@ +NVIDIA Tegra20 SFLASH controller. + +Required properties: +- compatible : should be "nvidia,tegra20-sflash". +- reg: Should contain SFLASH registers location and length. +- interrupts: Should contain SFLASH interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this SFLASH controller. + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +spi@7000c380 { + compatible = "nvidia,tegra20-sflash"; + reg = <0x7000c380 0x80>; + interrupts = <0 39 0x04>; + nvidia,dma-request-selector = <&apbdma 16>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; +}; + diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt new file mode 100644 index 00000000000..eefe15e3d95 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt @@ -0,0 +1,26 @@ +NVIDIA Tegra20/Tegra30 SLINK controller. + +Required properties: +- compatible : should be "nvidia,tegra20-slink", "nvidia,tegra30-slink". +- reg: Should contain SLINK registers location and length. +- interrupts: Should contain SLINK interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this SLINK controller. + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +spi@7000d600 { + compatible = "nvidia,tegra20-slink"; + reg = <0x7000d600 0x200>; + interrupts = <0 82 0x04>; + nvidia,dma-request-selector = <&apbdma 16>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; +}; + diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt index 81df374adbb..938809c6829 100644 --- a/Documentation/devicetree/bindings/spi/omap-spi.txt +++ b/Documentation/devicetree/bindings/spi/omap-spi.txt @@ -6,7 +6,9 @@ Required properties: - "ti,omap4-spi" for OMAP4+. - ti,spi-num-cs : Number of chipselect supported by the instance. - ti,hwmods: Name of the hwmod associated to the McSPI - +- ti,pindir-d0-out-d1-in: Select the D0 pin as output and D1 as + input. The default is D0 as input and + D1 as output. Example: diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index d2c33d0f533..296015e3c63 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -12,6 +12,7 @@ The SPI master node requires the following properties: - #size-cells - should be zero. - compatible - name of SPI bus controller following generic names recommended practice. +- cs-gpios - (optional) gpios chip select. No other properties are required in the SPI bus node. It is assumed that a driver for an SPI bus device will understand that it is an SPI bus. However, the binding does not attempt to define the specific method for @@ -24,6 +25,22 @@ support describing the chip select layout. Optional property: - num-cs : total number of chipselects +If cs-gpios is used the number of chip select will automatically increased +with max(cs-gpios > hw cs) + +So if for example the controller has 2 CS lines, and the cs-gpios +property looks like this: + +cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>; + +Then it should be configured so that num_chipselect = 4 with the +following mapping: + +cs0 : &gpio1 0 0 +cs1 : native +cs2 : &gpio1 1 0 +cs3 : &gpio1 2 0 + SPI slave nodes must be children of the SPI master node and can contain the following properties. - reg - (required) chip select address of device. @@ -36,6 +53,11 @@ contain the following properties. shifted clock phase (CPHA) mode - spi-cs-high - (optional) Empty property indicating device requires chip select active high +- spi-3wire - (optional) Empty property indicating device requires + 3-wire mode. + +If a gpio chipselect is used for the SPI slave the gpio number will be passed +via the cs_gpio SPI example for an MPC5200 SPI bus: spi@f00 { diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt new file mode 100644 index 00000000000..07e04cdc0c9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -0,0 +1,26 @@ +Atmel SPI device + +Required properties: +- compatible : should be "atmel,at91rm9200-spi". +- reg: Address and length of the register set for the device +- interrupts: Should contain spi interrupt +- cs-gpios: chipselects + +Example: + +spi1: spi@fffcc000 { + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffcc000 0x4000>; + interrupts = <13 4 5>; + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <&pioB 3 0>; + status = "okay"; + + mmc-slot@0 { + compatible = "mmc-spi-slot"; + reg = <0>; + gpios = <&pioC 4 0>; /* CD */ + spi-max-frequency = <25000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/thermal/db8500-thermal.txt b/Documentation/devicetree/bindings/thermal/db8500-thermal.txt new file mode 100644 index 00000000000..2e1c06fad81 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/db8500-thermal.txt @@ -0,0 +1,44 @@ +* ST-Ericsson DB8500 Thermal + +** Thermal node properties: + +- compatible : "stericsson,db8500-thermal"; +- reg : address range of the thermal sensor registers; +- interrupts : interrupts generated from PRCMU; +- interrupt-names : "IRQ_HOTMON_LOW" and "IRQ_HOTMON_HIGH"; +- num-trips : number of total trip points, this is required, set it 0 if none, + if greater than 0, the following properties must be defined; +- tripN-temp : temperature of trip point N, should be in ascending order; +- tripN-type : type of trip point N, should be one of "active" "passive" "hot" + "critical"; +- tripN-cdev-num : number of the cooling devices which can be bound to trip + point N, this is required if trip point N is defined, set it 0 if none, + otherwise the following cooling device names must be defined; +- tripN-cdev-nameM : name of the No. M cooling device of trip point N; + +Usually the num-trips and tripN-*** are separated in board related dts files. + +Example: +thermal@801573c0 { + compatible = "stericsson,db8500-thermal"; + reg = <0x801573c0 0x40>; + interrupts = <21 0x4>, <22 0x4>; + interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH"; + + num-trips = <3>; + + trip0-temp = <75000>; + trip0-type = "active"; + trip0-cdev-num = <1>; + trip0-cdev-name0 = "thermal-cpufreq-0"; + + trip1-temp = <80000>; + trip1-type = "active"; + trip1-cdev-num = <2>; + trip1-cdev-name0 = "thermal-cpufreq-0"; + trip1-cdev-name1 = "thermal-fan"; + + trip2-temp = <85000>; + trip2-type = "critical"; + trip2-cdev-num = <0>; +} diff --git a/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt b/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt new file mode 100644 index 00000000000..0c7b64e95a6 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt @@ -0,0 +1,17 @@ +Allwinner A1X SoCs Timer Controller + +Required properties: + +- compatible : should be "allwinner,sunxi-timer" +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupt of the first timer +- clocks: phandle to the source clock (usually a 24 MHz fixed clock) + +Example: + +timer { + compatible = "allwinner,sunxi-timer"; + reg = <0x01c20c00 0x400>; + interrupts = <22>; + clocks = <&osc>; +}; diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt new file mode 100644 index 00000000000..e019fdc3877 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt @@ -0,0 +1,21 @@ +NVIDIA Tegra20 timer + +The Tegra20 timer provides four 29-bit timer channels and a single 32-bit free +running counter. The first two channels may also trigger a watchdog reset. + +Required properties: + +- compatible : should be "nvidia,tegra20-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 4 interrupts; one per timer channel. + +Example: + +timer { + compatible = "nvidia,tegra20-timer"; + reg = <0x60005000 0x60>; + interrupts = <0 0 0x04 + 0 1 0x04 + 0 41 0x04 + 0 42 0x04>; +}; diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt new file mode 100644 index 00000000000..906109d4c59 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt @@ -0,0 +1,23 @@ +NVIDIA Tegra30 timer + +The Tegra30 timer provides ten 29-bit timer channels, a single 32-bit free +running counter, and 5 watchdog modules. The first two channels may also +trigger a legacy watchdog reset. + +Required properties: + +- compatible : should be "nvidia,tegra30-timer", "nvidia,tegra20-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 6 interrupts; one per each of timer channels 1 + through 5, and one for the shared interrupt for the remaining channels. + +timer { + compatible = "nvidia,tegra30-timer", "nvidia,tegra20-timer"; + reg = <0x60005000 0x400>; + interrupts = <0 0 0x04 + 0 1 0x04 + 0 41 0x04 + 0 42 0x04 + 0 121 0x04 + 0 122 0x04>; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt index 2ee903fad25..273a8d5b330 100644 --- a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt +++ b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt @@ -6,11 +6,19 @@ Required properties: - reg : Address and length of the register set for the device - interrupts : Should contain the auart interrupt numbers +Optional properties: +- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other + is for TX. If you add this property, it also means that you + will enable the DMA support for the auart. + Note: due to the hardware bug in imx23(see errata : 2836), + only the imx28 can enable the DMA support for the auart. + Example: auart0: serial@8006a000 { compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006a000 0x2000>; interrupts = <112 70 71>; + fsl,auart-dma-channel = <8 9>; }; Note: Each auart port should have an alias correctly numbered in "aliases" diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index ba385f2e0dd..1e1145ca4f3 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -14,7 +14,10 @@ Required properties: - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. -- clock-frequency : the input clock frequency for the UART. +- clock-frequency : the input clock frequency for the UART + or + clocks phandle to refer to the clk used as per Documentation/devicetree + /bindings/clock/clock-bindings.txt Optional properties: - current-speed : the current active speed of the UART. diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index ca8fa56e9f0..ea840f7f925 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -1,14 +1,35 @@ AM33XX MUSB GLUE - compatible : Should be "ti,musb-am33xx" + - reg : offset and length of register sets, first usbss, then for musb instances + - interrupts : usbss, musb instance interrupts in order - ti,hwmods : must be "usb_otg_hs" - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - - num_eps : Specifies the number of endpoints. This is also a + - num-eps : Specifies the number of endpoints. This is also a MUSB configuration-specific setting. Should be set to "16" - - ram_bits : Specifies the ram address size. Should be set to "12" - - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + - ram-bits : Specifies the ram address size. Should be set to "12" + - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2" represents PERIPHERAL. - - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2" + - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2" represents PERIPHERAL. - power : Should be "250". This signifies the controller can supply upto 500mA when operating in host mode. + +Example: + +usb@47400000 { + compatible = "ti,musb-am33xx"; + reg = <0x47400000 0x1000 /* usbss */ + 0x47401000 0x800 /* musb instance 0 */ + 0x47401800 0x800>; /* musb instance 1 */ + interrupts = <17 /* usbss */ + 18 /* musb instance 0 */ + 19>; /* musb instance 1 */ + multipoint = <1>; + num-eps = <16>; + ram-bits = <12>; + port0-mode = <3>; + port1-mode = <3>; + power = <250>; + ti,hwmods = "usb_otg_hs"; +}; diff --git a/Documentation/devicetree/bindings/usb/ehci-orion.txt b/Documentation/devicetree/bindings/usb/ehci-orion.txt new file mode 100644 index 00000000000..6bc09ec14c4 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-orion.txt @@ -0,0 +1,15 @@ +* EHCI controller, Orion Marvell variants + +Required properties: +- compatible: must be "marvell,orion-ehci" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The EHCI interrupt + +Example: + + ehci@50000 { + compatible = "marvell,orion-ehci"; + reg = <0x50000 0x1000>; + interrupts = <19>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 9de2b9ff9d6..902b1b1f568 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -5,6 +5,7 @@ using them to avoid name-space collisions. ad Avionic Design GmbH adi Analog Devices, Inc. +ak Asahi Kasei Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. @@ -25,6 +26,7 @@ gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. hp Hewlett Packard ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. +img Imagination Technologies Ltd. intercontrol Inter Control Group linux Linux-specific binding marvell Marvell Technology Group Ltd. @@ -34,8 +36,9 @@ national National Semiconductor nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors +onnn ON Semiconductor Corp. picochip Picochip Ltd -powervr Imagination Technologies +powervr PowerVR (deprecated, use img) qcom Qualcomm, Inc. ramtron Ramtron International realtek Realtek Semiconductor Corp. @@ -45,10 +48,12 @@ schindler Schindler sil Silicon Image simtek sirf SiRF Technology, Inc. +snps Synopsys, Inc. st STMicroelectronics stericsson ST-Ericsson ti Texas Instruments via VIA Technologies, Inc. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. +winbond Winbond Electronics corp. xlnx Xilinx diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt new file mode 100644 index 00000000000..c60da67a5d7 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -0,0 +1,80 @@ +The Exynos display port interface should be configured based on +the type of panel connected to it. + +We use two nodes: + -dp-controller node + -dptx-phy node(defined inside dp-controller node) + +For the DP-PHY initialization, we use the dptx-phy node. +Required properties for dptx-phy: + -reg: + Base address of DP PHY register. + -samsung,enable-mask: + The bit-mask used to enable/disable DP PHY. + +For the Panel initialization, we read data from dp-controller node. +Required properties for dp-controller: + -compatible: + should be "samsung,exynos5-dp". + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -interrupt-parent: + phandle to Interrupt combiner node. + -samsung,color-space: + input video data format. + COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 + -samsung,dynamic-range: + dynamic range for input video data. + VESA = 0, CEA = 1 + -samsung,ycbcr-coeff: + YCbCr co-efficients for input video. + COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 + -samsung,color-depth: + number of bits per colour component. + COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 + -samsung,link-rate: + link rate supported by the panel. + LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A + -samsung,lane-count: + number of lanes supported by the panel. + LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 + +Optional properties for dp-controller: + -interlaced: + interlace scan mode. + Progressive if defined, Interlaced if not defined + -vsync-active-high: + VSYNC polarity configuration. + High if defined, Low if not defined + -hsync-active-high: + HSYNC polarity configuration. + High if defined, Low if not defined + +Example: + +SOC specific portion: + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + + dptx-phy { + reg = <0x10040720>; + samsung,enable-mask = <1>; + }; + + }; + +Board Specific portion: + dp-controller { + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <4>; + }; diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt new file mode 100644 index 00000000000..3d0060cff06 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt @@ -0,0 +1,24 @@ +* Solomon SSD1307 Framebuffer Driver + +Required properties: + - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for + now is i2c. + - reg: Should contain address of the controller on the I2C bus. Most likely + 0x3c or 0x3d + - pwm: Should contain the pwm to use according to the OF device tree PWM + specification [0] + - reset-gpios: Should contain the GPIO used to reset the OLED display + +Optional properties: + - reset-active-low: Is the reset gpio is active on physical low? + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt + +Examples: +ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7>; + reset-active-low; +}; diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt new file mode 100644 index 00000000000..2957ebb5aa7 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt @@ -0,0 +1,15 @@ +* Atmel Watchdog Timers + +** at91sam9-wdt + +Required properties: +- compatible: must be "atmel,at91sam9260-wdt". +- reg: physical base address of the controller and length of memory mapped + region. + +Example: + + watchdog@fffffd40 { + compatible = "atmel,at91sam9260-wdt"; + reg = <0xfffffd40 0x10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt new file mode 100644 index 00000000000..d209366b4a6 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt @@ -0,0 +1,13 @@ +BCM2835 Watchdog timer + +Required properties: + +- compatible : should be "brcm,bcm2835-pm-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +watchdog { + compatible = "brcm,bcm2835-pm-wdt"; + reg = <0x7e100000 0x28>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt new file mode 100644 index 00000000000..75558ccd9a0 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt @@ -0,0 +1,12 @@ +DaVinci Watchdog Timer (WDT) Controller + +Required properties: +- compatible : Should be "ti,davinci-wdt" +- reg : Should contain WDT registers location and length + +Examples: + +wdt: wdt@2320000 { + compatible = "ti,davinci-wdt"; + reg = <0x02320000 0x80>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt new file mode 100644 index 00000000000..0b271777560 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt @@ -0,0 +1,13 @@ +Allwinner sunXi Watchdog timer + +Required properties: + +- compatible : should be "allwinner,sunxi-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +wdt: watchdog@01c20c90 { + compatible = "allwinner,sunxi-wdt"; + reg = <0x01c20c90 0x10>; +}; |