summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt')
-rw-r--r--Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt70
1 files changed, 70 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt
new file mode 100644
index 00000000000..e47734bee3f
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt
@@ -0,0 +1,70 @@
+* UCC (Unified Communications Controllers)
+
+Required properties:
+- device_type : should be "network", "hldc", "uart", "transparent"
+ "bisync", "atm", or "serial".
+- compatible : could be "ucc_geth" or "fsl_atm" and so on.
+- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+- pio-handle : The phandle for the Parallel I/O port configuration.
+- port-number : for UART drivers, the port number to use, between 0 and 3.
+ This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
+ The port number is added to the minor number of the device. Unlike the
+ CPM UART driver, the port-number is required for the QE UART driver.
+- soft-uart : for UART drivers, if specified this means the QE UART device
+ driver should use "Soft-UART" mode, which is needed on some SOCs that have
+ broken UART hardware. Soft-UART is provided via a microcode upload.
+- rx-clock-name: the UCC receive clock source
+ "none": clock source is disabled
+ "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+ "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- tx-clock-name: the UCC transmit clock source
+ "none": clock source is disabled
+ "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+ "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+The following two properties are deprecated. rx-clock has been replaced
+with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
+Drivers that currently use the deprecated properties should continue to
+do so, in order to support older device trees, but they should be updated
+to check for the new properties first.
+- rx-clock : represents the UCC receive clock source.
+ 0x00 : clock source is disabled;
+ 0x1~0x10 : clock source is BRG1~BRG16 respectively;
+ 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+- tx-clock: represents the UCC transmit clock source;
+ 0x00 : clock source is disabled;
+ 0x1~0x10 : clock source is BRG1~BRG16 respectively;
+ 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+
+Required properties for network device_type:
+- mac-address : list of bytes representing the ethernet address.
+- phy-handle : The phandle for the PHY connected to this controller.
+
+Recommended properties:
+- phy-connection-type : a string naming the controller/PHY interface type,
+ i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
+ Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
+ "tbi", or "rtbi".
+
+Example:
+ ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <1>;
+ reg = <2000 200>;
+ interrupts = <a0 0>;
+ interrupt-parent = <700>;
+ mac-address = [ 00 04 9f 00 23 23 ];
+ rx-clock = "none";
+ tx-clock = "clk9";
+ phy-handle = <212000>;
+ phy-connection-type = "gmii";
+ pio-handle = <140001>;
+ };