1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
|
/*
* arch/arm/mach-ixp4xx/nslu2-setup.c
*
* NSLU2 board-setup
*
* based ixdp425-setup.c:
* Copyright (C) 2003-2004 MontaVista Software, Inc.
*
* Author: Mark Rakes <mrakes at mac.com>
* Author: Rod Whitby <rod@whitby.id.au>
* Maintainers: http://www.nslu2-linux.org/
*
* Fixed missing init_time in MACHINE_START kas11 10/22/04
* Changed to conform to new style __init ixdp425 kas11 10/22/04
*/
#include <linux/kernel.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
#include <linux/leds.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
static struct flash_platform_data nslu2_flash_data = {
.map_name = "cfi_probe",
.width = 2,
};
static struct resource nslu2_flash_resource = {
.flags = IORESOURCE_MEM,
};
static struct platform_device nslu2_flash = {
.name = "IXP4XX-Flash",
.id = 0,
.dev.platform_data = &nslu2_flash_data,
.num_resources = 1,
.resource = &nslu2_flash_resource,
};
static struct ixp4xx_i2c_pins nslu2_i2c_gpio_pins = {
.sda_pin = NSLU2_SDA_PIN,
.scl_pin = NSLU2_SCL_PIN,
};
#ifdef CONFIG_LEDS_IXP4XX
static struct resource nslu2_led_resources[] = {
{
.name = "ready", /* green led */
.start = NSLU2_LED_GRN,
.end = NSLU2_LED_GRN,
.flags = IXP4XX_GPIO_HIGH,
},
{
.name = "status", /* red led */
.start = NSLU2_LED_RED,
.end = NSLU2_LED_RED,
.flags = IXP4XX_GPIO_HIGH,
},
{
.name = "disk-1",
.start = NSLU2_LED_DISK1,
.end = NSLU2_LED_DISK1,
.flags = IXP4XX_GPIO_LOW,
},
{
.name = "disk-2",
.start = NSLU2_LED_DISK2,
.end = NSLU2_LED_DISK2,
.flags = IXP4XX_GPIO_LOW,
},
};
static struct platform_device nslu2_leds = {
.name = "IXP4XX-GPIO-LED",
.id = -1,
.num_resources = ARRAY_SIZE(nslu2_led_resources),
.resource = nslu2_led_resources,
};
#endif
static struct platform_device nslu2_i2c_controller = {
.name = "IXP4XX-I2C",
.id = 0,
.dev.platform_data = &nslu2_i2c_gpio_pins,
.num_resources = 0,
};
static struct platform_device nslu2_beeper = {
.name = "ixp4xx-beeper",
.id = NSLU2_GPIO_BUZZ,
.num_resources = 0,
};
static struct resource nslu2_uart_resources[] = {
{
.start = IXP4XX_UART1_BASE_PHYS,
.end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
},
{
.start = IXP4XX_UART2_BASE_PHYS,
.end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
}
};
static struct plat_serial8250_port nslu2_uart_data[] = {
{
.mapbase = IXP4XX_UART1_BASE_PHYS,
.membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART1,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{
.mapbase = IXP4XX_UART2_BASE_PHYS,
.membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART2,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{ }
};
static struct platform_device nslu2_uart = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev.platform_data = nslu2_uart_data,
.num_resources = 2,
.resource = nslu2_uart_resources,
};
static struct platform_device *nslu2_devices[] __initdata = {
&nslu2_i2c_controller,
&nslu2_flash,
&nslu2_beeper,
#ifdef CONFIG_LEDS_IXP4XX
&nslu2_leds,
#endif
};
static void nslu2_power_off(void)
{
/* This causes the box to drop the power and go dead. */
/* enable the pwr cntl gpio */
gpio_line_config(NSLU2_PO_GPIO, IXP4XX_GPIO_OUT);
/* do the deed */
gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH);
}
static void __init nslu2_init(void)
{
ixp4xx_sys_init();
nslu2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
nslu2_flash_resource.end =
IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
pm_power_off = nslu2_power_off;
/* This is only useful on a modified machine, but it is valuable
* to have it first in order to see debug messages, and so that
* it does *not* get removed if platform_add_devices fails!
*/
(void)platform_device_register(&nslu2_uart);
platform_add_devices(nslu2_devices, ARRAY_SIZE(nslu2_devices));
}
MACHINE_START(NSLU2, "Linksys NSLU2")
/* Maintainer: www.nslu2-linux.org */
.phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
.io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
.boot_params = 0x00000100,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
.init_machine = nslu2_init,
MACHINE_END
|
