| Age | Commit message (Collapse) | Author |
|---|
|
I was (at least) the second person trying to fix a warning by sparse, so
document in the code why this is a bad idea and add an extern declaration to
make sparse happy.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
This allows to put the filesystem at a defined address in ROM allowing
to save more precious RAM.
I think it's safe to default to ROM because the intention of using the
uclinux map is to use a romfs and so mtd-ram doesn't give you anything
that mtd-rom doesn't.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
|
|
It's required for accessing trx header (usually re-calculating a
checksum) and for writing a new firmware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
|
|
Add support for GigaDevice GD25Q32 32 Mbit (4 MB) SPI Flash (see datasheet:
http://www.gigadevice.com/UserFiles/GD25Q32_Rev0.2(1).pdf) used in Hame MPR-A1
and clones, and for GigaDevice GD25Q64 64 Mbit (8 MB) SPI Flash used in
Hame MPR-A2 devices (datasheet: http://www.gigadevice.com/UserFiles/GD25Q64.pdf).
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
ELM module can be used for hardware error correction of BCH 4 & 8 bit.
ELM module functionality is verified by checking the availability of
handle for ELM module in device tree. Hence supporting
1. ELM module available, BCH error correction done by ELM module. Also
support read & write page in one shot by adding custom read_page and
write_page methods. This helps in optimizing code for NAND flashes with
page size less than 4 KB.
2. If ELM module not available fall back to software BCH error
correction support.
New structure member is added to omap_nand_info
1. "is_elm_used" to know the status of whether the ELM module is used for
error correction or not.
2. "elm_dev" device pointer to elm device on detection of ELM module.
Also being here update the device tree documentation of gpmc-nand for
adding optional property elm_id.
Note:
ECC layout uses 1 extra bytes for 512 byte of data to handle erased
pages. Extra byte programmed to zero for programmed pages. Also BCH8
requires 14 byte ecc to maintain compatibility with RBL ECC layout.
This results a common ecc layout across RBL, U-boot & Linux with BCH8.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme
error correction.
For now only 4 & 8 bit support is added
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Remove check of ecc bytes with 13, number of errors can directly update
from nand ecc strength. This will increase re-usability of the code.
Also add macro definitions BCH8_ERROR_MAX & BCH4_ERROR_MAX for better
readability and cleaner code.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Also compress the id in case of a v3 NAND flash controller (i.mx51, i.mx53)
and 16Bit buswidth.
Signed-off-by: Roman Schneider <schneider@at.festo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
This patch adds generic support for flash protection on STmicro chips.
On chips with less than 3 protection bits, the unused bits are don't cares
and so can be written anyway. The lock function will only change the
protection bits if it would not unlock other areas. Similarly, the unlock
function will not lock currently unlocked areas. Tested on the m25p64.
Signed-off-by: Austin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Use more preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
/proc/mtd doesn't contain the mtd-id of the device, but the part name from the
command line. This corrects what I believe is an obsolete comment from commit
a0ee24a03b1c06813c814b9f70946c8984752f01.
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Cc: Philip Rakity <prakity@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The mtd documentation makes no mention of the useful feature whereby
partitions' logical ordering need not match their physical ordering.
Truncation of parts, skipping of zero sized parts, and handling of
overlapping parts are similarly not mentioned.
This updates the comments at the top of file describing the command
line parsing as currently implemented. I proposed this in
http://lists.infradead.org/pipermail/linux-mtd/2012-December/045314.html
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Perform flash size truncation before skipping zero sized partition
so that if the result is a zero sized, it will be skipped like the
others.
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Acked-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Decrement index i after skipping a zero sized partition. On next loop
iteration, the index will be the same as before, but the data will be
new as it was moved when earlier partition was skipped.
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Acked-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Always report corrected and failed ECC stats back up to the MTD layer. Also
return max_bitflips from read_page() as is expected from NAND drivers now.
Signed-off-by: Zach Sadecki <zsadecki@itwatchdogs.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Fix missing dependency which can cause a build error such
as: ERROR: "byte_rev_table" [drivers/mtd/devices/docg3.ko]
undefined!
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Commit cdeadd712f52b16a9285386d61ee26fd14eb4085 (mtd: nand: davinci: add OF
support for davinci nand controller) has never been really build tested with
the driver as a module. When the driver is built-in, the missing semicolon
after structure initializer is "compensated" by MODULE_DEVICE_TABLE() macro
being empty and so the initializer using the trailing semicolon on the next
line; when the driver is built as a module, compilation error ensues, and as
the 'davinci_all_defconfig' has the NAND driver modular, this error prevents
DaVinci family kernel from building...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org # 3.7
|
|
Pass an optional device_node pointer in the platform data,
which in turn will be put into a mtd_part_parser_data.
This way, code that sets up the platform devices can pass
along the node from DT so that the partitions can be parsed.
For non-DT boards, this change has no effect.
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adds the FSMC NAND driver and flash partitions to the Nomadik
device tree.
The only compatible string accepted by this driver is currently
"st,spear600-fsmc-nand" which is inappropriate for this system, so
this patch adds the compatible value "stericsson,fsmc-nand" as
well.
Cc: linux-mtd@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ff3206b2450499203532af2505a7f6f8413e92c0 ('mtd: nand: onfi need
to be probed in 8 bits mode') adds a WARN if the onfi probe is in 16
bits mode. This allows to detect driver that need to be fixed, but this
is a bit noisy¹. Transform the WARN in a pr_err.
¹ http://article.gmane.org/gmane.linux.ports.arm.omap/91317
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Commit d68cbdd4fb (mtd: physmap_of: allow to specify the mtd name for retro
compatiblity) broke cmdline partitioning using dev_name() in the kernel command
line. of_property_read_string() does not touch mtd_name when linux,mtd-name is
not present in the device tree, which causes map.name to be set to a random
value. Fix this by initializing mtd_name to NULL.
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Fix missing dependency which can cause a build error such
as: ERROR: "byte_rev_table" [drivers/mtd/devices/docg3.ko]
undefined!
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Pass an optional device_node pointer in the platform data, which in turn
will be put into a mtd_part_parser_data. This way, code that sets up the
platform devices can pass along the node from DT so that the partitions
can be parsed.
For non-DT boards, this change has no effect.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: David Woodhouse <dwmw2@infradead.org>
CC: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
CC: Huang Shijie <b32955@freescale.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: David Woodhouse <dwmw2@infradead.org>
CC: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
CC: Robert Jarzmik <robert.jarzmik@free.fr>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Richard Weinberger <richard@nod.at>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
Commit cdeadd712f52b16a9285386d61ee26fd14eb4085 (mtd: nand: davinci: add OF
support for davinci nand controller) has never been really build tested with
the driver as a module. When the driver is built-in, the missing semicolon
after structure initializer is "compensated" by MODULE_DEVICE_TABLE() macro
being empty and so the initializer using the trailing semicolon on the next
line; when the driver is built as a module, compilation error ensues, and as
the 'davinci_all_defconfig' has the NAND driver modular, this error prevents
DaVinci family kernel from building...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org # 3.7
|
|
Make dma_xfer() do DMA unmapping itself and fix handling
of failure cases.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dan Williams <djbw@fb.com>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Recently imlemented writing support has shown that current num of
retries is too low. Writing requires longer waiting than simple reading.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Pull UBI update from Artem Bityutskiy:
"Nothing exciting, just clean-ups and nicification. Oh, and one small
optimization which makes UBI to use less RAM."
* tag 'upstream-3.8-rc1' of git://git.infradead.org/linux-ubi:
UBI: embed ubi_debug_info field in ubi_device struct
UBI: introduce helpers dbg_chk_{io, gen}
UBI: replace memcpy with struct assignment
UBI: remove spurious comment
UBI: gluebi: rename misleading variables
UBI: do not allocate the memory unnecessarily
UBI: use list_move_tail instead of list_del/list_add_tail
|
|
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
|
|
This also removes unnecessary memset call which is immediately overwritten
with random bytes.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Laight <david.laight@aculab.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform conversion patches from Olof Johansson:
"Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is not
quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq.
Note that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled."
Fix up conflicts mostly as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
clocksource/mtu-nomadik: use apb_pclk
clk: ux500: Register mtu apb_pclocks
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
...
|
|
The simple example provided in the comments for nand_id_has_period()
actually has a period of 3, not 2. Silly mistake...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.
This patch replaces the usage of these string functions in the mtd
gpio accessors with io{read,write}{8,16,32}_rep calls instead.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
If you create a block2mtd device that is larger than main memory,
and write to all of it, then lots of pages will be dirtied but
they will never be flushed out as nothing calls any variant of
balance_dirty_pages.
It would be nice to call set_page_dirty_balance(), but that isn't exported,
so just call balance_dirty_pages_ratelimited() directly.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
It could happen (1 out of 100 times) that NAND did not start up
correctly after warm rebooting, so the kernel could not find the UBI or
DMA timed out due to a stalled BCH. When resetting BCH together with
GPMI, the issue could not be observed anymore (after 10000+ reboots). We
probably need the consistent state already before sending any command to
NAND, even when no ECC is needed. I chose to keep the extra reset for
BCH when changing the flash layout to be on the safe side.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
|
|
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
|
|
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
|
|
This patch does two things related to reading the factory badblock table during
initialization: (1) fix error where a non-zero return code from
docg4_read_page() is assumed to be an error (it was later changed to be
max_bitflips; thanks to Brian Norris for bringing this to my attention a while
back), and (2) if there is an error reading the factory bbt, it tries reading
another (redundant) factory bbt table.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Modify the nand_ecclayout to place the two bb marker bytes in the oob region
off-limits to the user.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The controller on the docg4 has a "reliable" mode, where consecutive 2k pages
are used in parallel. The initial program loader (IPL) on my Treo 680 expects
the secondary program loader (SPL) to be written in this mode. This patch adds
support for writing data in reliable mode, by way of a module parameter.
Support for reading in this mode (as the IPL does) is not supported yet, but
alternate (even-numbered) 2k pages written in reliable mode can be read normally
(odd-numbered pages will contain junk and generate ecc errors).
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
