1 files changed, 57 insertions, 75 deletions

diff --git a/drivers/tty/serial/8250.c b/drivers/tty/serial/8250.c
index 7f50999eebc..a87a56cb541 100644
--- a/drivers/tty/serial/8250.c
+++ b/drivers/tty/serial/8250.c
@@ -309,6 +309,13 @@ static const struct serial8250_config uart_config[] = {
 				  UART_FCR_T_TRIG_01,
 		.flags		= UART_CAP_FIFO | UART_CAP_RTOIE,
 	},
+	[PORT_XR17D15X] = {
+		.name		= "XR17D15X",
+		.fifo_size	= 64,
+		.tx_loadsz	= 64,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR,
+	},
 };
 
 #if defined(CONFIG_MIPS_ALCHEMY)
@@ -461,42 +468,6 @@ static void tsi_serial_out(struct uart_port *p, int offset, int value)
 		writeb(value, p->membase + offset);
 }
 
-/* Save the LCR value so it can be re-written when a Busy Detect IRQ occurs. */
-static inline void dwapb_save_out_value(struct uart_port *p, int offset,
-					int value)
-{
-	struct uart_8250_port *up =
-		container_of(p, struct uart_8250_port, port);
-
-	if (offset == UART_LCR)
-		up->lcr = value;
-}
-
-/* Read the IER to ensure any interrupt is cleared before returning from ISR. */
-static inline void dwapb_check_clear_ier(struct uart_port *p, int offset)
-{
-	if (offset == UART_TX || offset == UART_IER)
-		p->serial_in(p, UART_IER);
-}
-
-static void dwapb_serial_out(struct uart_port *p, int offset, int value)
-{
-	int save_offset = offset;
-	offset = map_8250_out_reg(p, offset) << p->regshift;
-	dwapb_save_out_value(p, save_offset, value);
-	writeb(value, p->membase + offset);
-	dwapb_check_clear_ier(p, save_offset);
-}
-
-static void dwapb32_serial_out(struct uart_port *p, int offset, int value)
-{
-	int save_offset = offset;
-	offset = map_8250_out_reg(p, offset) << p->regshift;
-	dwapb_save_out_value(p, save_offset, value);
-	writel(value, p->membase + offset);
-	dwapb_check_clear_ier(p, save_offset);
-}
-
 static unsigned int io_serial_in(struct uart_port *p, int offset)
 {
 	offset = map_8250_in_reg(p, offset) << p->regshift;
@@ -509,6 +480,8 @@ static void io_serial_out(struct uart_port *p, int offset, int value)
 	outb(value, p->iobase + offset);
 }
 
+static int serial8250_default_handle_irq(struct uart_port *port);
+
 static void set_io_from_upio(struct uart_port *p)
 {
 	struct uart_8250_port *up =
@@ -540,16 +513,6 @@ static void set_io_from_upio(struct uart_port *p)
 		p->serial_out = tsi_serial_out;
 		break;
 
-	case UPIO_DWAPB:
-		p->serial_in = mem_serial_in;
-		p->serial_out = dwapb_serial_out;
-		break;
-
-	case UPIO_DWAPB32:
-		p->serial_in = mem32_serial_in;
-		p->serial_out = dwapb32_serial_out;
-		break;
-
 	default:
 		p->serial_in = io_serial_in;
 		p->serial_out = io_serial_out;
@@ -557,6 +520,7 @@ static void set_io_from_upio(struct uart_port *p)
 	}
 	/* Remember loaded iotype */
 	up->cur_iotype = p->iotype;
+	p->handle_irq = serial8250_default_handle_irq;
 }
 
 static void
@@ -567,8 +531,6 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value)
 	case UPIO_MEM:
 	case UPIO_MEM32:
 	case UPIO_AU:
-	case UPIO_DWAPB:
-	case UPIO_DWAPB32:
 		p->serial_out(p, offset, value);
 		p->serial_in(p, UART_LCR);	/* safe, no side-effects */
 		break;
@@ -1120,6 +1082,14 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 	serial_outp(up, UART_IER, iersave);
 
 	/*
+	 * Exar uarts have EFR in a weird location
+	 */
+	if (up->port.flags & UPF_EXAR_EFR) {
+		up->port.type = PORT_XR17D15X;
+		up->capabilities |= UART_CAP_AFE | UART_CAP_EFR;
+	}
+
+	/*
 	 * We distinguish between 16550A and U6 16550A by counting
 	 * how many bytes are in the FIFO.
 	 */
@@ -1621,6 +1591,29 @@ static void serial8250_handle_port(struct uart_8250_port *up)
 	spin_unlock_irqrestore(&up->port.lock, flags);
 }
 
+int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
+{
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
+
+	if (!(iir & UART_IIR_NO_INT)) {
+		serial8250_handle_port(up);
+		return 1;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(serial8250_handle_irq);
+
+static int serial8250_default_handle_irq(struct uart_port *port)
+{
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
+	unsigned int iir = serial_in(up, UART_IIR);
+
+	return serial8250_handle_irq(port, iir);
+}
+
 /*
  * This is the serial driver's interrupt routine.
  *
@@ -1648,30 +1641,13 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id)
 	l = i->head;
 	do {
 		struct uart_8250_port *up;
-		unsigned int iir;
+		struct uart_port *port;
 
 		up = list_entry(l, struct uart_8250_port, list);
+		port = &up->port;
 
-		iir = serial_in(up, UART_IIR);
-		if (!(iir & UART_IIR_NO_INT)) {
-			serial8250_handle_port(up);
-
+		if (port->handle_irq(port)) {
 			handled = 1;
-
-			end = NULL;
-		} else if ((up->port.iotype == UPIO_DWAPB ||
-			    up->port.iotype == UPIO_DWAPB32) &&
-			  (iir & UART_IIR_BUSY) == UART_IIR_BUSY) {
-			/* The DesignWare APB UART has an Busy Detect (0x07)
-			 * interrupt meaning an LCR write attempt occurred while the
-			 * UART was busy. The interrupt must be cleared by reading
-			 * the UART status register (USR) and the LCR re-written. */
-			unsigned int status;
-			status = *(volatile u32 *)up->port.private_data;
-			serial_out(up, UART_LCR, up->lcr);
-
-			handled = 1;
-
 			end = NULL;
 		} else if (end == NULL)
 			end = l;
@@ -2081,8 +2057,8 @@ static int serial8250_startup(struct uart_port *port)
 	 */
 	if (!(up->port.flags & UPF_BUGGY_UART) &&
 	    (serial_inp(up, UART_LSR) == 0xff)) {
-		printk(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
-		       serial_index(&up->port));
+		printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
+				   serial_index(&up->port));
 		return -ENODEV;
 	}
 
@@ -2458,7 +2434,10 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
 			efr |= UART_EFR_CTS;
 
 		serial_outp(up, UART_LCR, UART_LCR_CONF_MODE_B);
-		serial_outp(up, UART_EFR, efr);
+		if (up->port.flags & UPF_EXAR_EFR)
+			serial_outp(up, UART_XR_EFR, efr);
+		else
+			serial_outp(up, UART_EFR, efr);
 	}
 
 #ifdef CONFIG_ARCH_OMAP
@@ -2570,8 +2549,6 @@ static int serial8250_request_std_resource(struct uart_8250_port *up)
 	case UPIO_TSI:
 	case UPIO_MEM32:
 	case UPIO_MEM:
-	case UPIO_DWAPB:
-	case UPIO_DWAPB32:
 		if (!up->port.mapbase)
 			break;
 
@@ -2608,8 +2585,6 @@ static void serial8250_release_std_resource(struct uart_8250_port *up)
 	case UPIO_TSI:
 	case UPIO_MEM32:
 	case UPIO_MEM:
-	case UPIO_DWAPB:
-	case UPIO_DWAPB32:
 		if (!up->port.mapbase)
 			break;
 
@@ -3050,6 +3025,10 @@ int __init early_serial_setup(struct uart_port *port)
 		p->serial_in = port->serial_in;
 	if (port->serial_out)
 		p->serial_out = port->serial_out;
+	if (port->handle_irq)
+		p->handle_irq = port->handle_irq;
+	else
+		p->handle_irq = serial8250_default_handle_irq;
 
 	return 0;
 }
@@ -3118,6 +3097,7 @@ static int __devinit serial8250_probe(struct platform_device *dev)
 		port.type		= p->type;
 		port.serial_in		= p->serial_in;
 		port.serial_out		= p->serial_out;
+		port.handle_irq		= p->handle_irq;
 		port.set_termios	= p->set_termios;
 		port.pm			= p->pm;
 		port.dev		= &dev->dev;
@@ -3283,6 +3263,8 @@ int serial8250_register_port(struct uart_port *port)
 			uart->port.serial_in = port->serial_in;
 		if (port->serial_out)
 			uart->port.serial_out = port->serial_out;
+		if (port->handle_irq)
+			uart->port.handle_irq = port->handle_irq;
 		/*  Possibly override set_termios call */
 		if (port->set_termios)
 			uart->port.set_termios = port->set_termios;