diff options
Diffstat (limited to 'Documentation')
5 files changed, 17 insertions, 21 deletions
diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt index baadbb11fe9..5083c0b834b 100644 --- a/Documentation/devicetree/bindings/clock/imx23-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -60,11 +60,6 @@ clks: clkctrl@80040000 { compatible = "fsl,imx23-clkctrl"; reg = <0x80040000 0x2000>; #clock-cells = <1>; - clock-output-names = - ... - "uart", /* 32 */ - ... - "end_of_list"; }; auart0: serial@8006c000 { diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt index c2a3525ecb4..db4f2f05c4d 100644 --- a/Documentation/devicetree/bindings/clock/imx25-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -146,10 +146,6 @@ clks: ccm@53f80000 { compatible = "fsl,imx25-ccm"; reg = <0x53f80000 0x4000>; interrupts = <31>; - clock-output-names = ... - "uart_ipg", - "uart_serial", - ...; }; uart1: serial@43f90000 { diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt index 52a49a4a50b..e6587af62ff 100644 --- a/Documentation/devicetree/bindings/clock/imx28-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -83,11 +83,6 @@ clks: clkctrl@80040000 { compatible = "fsl,imx28-clkctrl"; reg = <0x80040000 0x2000>; #clock-cells = <1>; - clock-output-names = - ... - "uart", /* 45 */ - ... - "end_of_list"; }; auart0: serial@8006a000 { diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index d77b4e68dc4..f73fdf59556 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -211,10 +211,6 @@ clks: ccm@020c4000 { reg = <0x020c4000 0x4000>; interrupts = <0 87 0x04 0 88 0x04>; #clock-cells = <1>; - clock-output-names = ... - "uart_ipg", - "uart_serial", - ...; }; uart1: serial@02020000 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt index 558cdf3c9ab..d4eab9227ea 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt @@ -1,4 +1,19 @@ -GPIO line that should be set high/low to power off a device +Driver a GPIO line that can be used to turn the power off. + +The driver supports both level triggered and edge triggered power off. +At driver load time, the driver will request the given gpio line and +install a pm_power_off handler. If the optional properties 'input' is +not found, the GPIO line will be driven in the inactive +state. Otherwise its configured as an input. + +When the pm_power_off is called, the gpio is configured as an output, +and drive active, so triggering a level triggered power off +condition. This will also cause an inactive->active edge condition, so +triggering positive edge triggered power off. After a delay of 100ms, +the GPIO is set to inactive, thus causing an active->inactive edge, +triggering negative edge triggered power off. After another 100ms +delay the GPIO is driver active again. If the power is still on and +the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. Required properties: - compatible : should be "gpio-poweroff". @@ -13,10 +28,9 @@ Optional properties: property is not specified, the GPIO is initialized as an output in its inactive state. - Examples: gpio-poweroff { compatible = "gpio-poweroff"; - gpios = <&gpio 4 0>; /* GPIO 4 Active Low */ + gpios = <&gpio 4 0>; }; |