drm/i915: fix Haswell FDI link training code

This commit makes hsw_fdi_link_train responsible for implementing
everything described in the "Enable and train FDI" section from the
Hawell CRT mode set sequence documentation. We completely rewrite
hsw_fdi_link_train to match the documentation and we also call it in
the right place.

This patch was initially sent as a series of tiny patches fixing every
little problem of the function, but since there were too many patches
fixing the same function it got a little difficult to get the "big
picture" of how the function would be in the end, so here we amended
all the patches into a single big patch fixing the whole function.

Problems we fixed:

  1 - Train Haswell FDI at the right time.

    We need to train the FDI before enabling the pipes and planes, so
    we're moving the call from lpt_pch_enable to haswell_crtc_enable
    directly.

    We are also removing ironlake_fdi_pll_enable since the PLL
    enablement on Haswell is completely different and is also done
    during the link training steps.

  2 - Use the right FDI_RX_CTL register on Haswell

    There is only one PCH transcoder, so it's always _FDI_RXA_CTL.
    Using "pipe" here is wrong.

  3 - Don't rely on DDI_BUF_CTL previous values

    Just set the bits we want, everything else is zero. Also
    POSTING_READ the register before sleeping.

  4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train

    According to the mode set sequence documentation, this is the
    right place. According to the FDI_RX_TUSIZE register description,
    this is the value we should set.

    Also remove the code that sets this register from the old
    location: lpt_pch_enable.

  5 - Properly program FDI_RX_MISC pwrdn lane values on HSW

  6 - Wait only 35us for the FDI link training

    First we wait 30us for the FDI receiver lane calibration, then we
    wait 5us for the FDI auto training time.

  7 - Remove an useless indentation level on hsw_fdi_link_train

    We already "break" when the link training succeeds.

  8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE

    When we fail the training.

  9 - Change Haswell FDI link training error messages

    We shouldn't call DRM_ERROR when still looping through voltage
    levels since this is expected and not really a failure. So in this
    commit we adjust the error path to only DRM_ERROR when we really
    fail after trying everything.

    While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since
    it's what we use everywhere.

  10 - Try each voltage twice at hsw_fdi_link_train

    Now with Daniel Vetter's suggestion to use "/2" instead of ">>1".

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Applied tiny bikesheds:
- mention in comment that we test each voltage/emphasis level twice
- realing arguments of the only untouched reg write, it spilled over
  the 80 char limit ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

1 files changed, 11 insertions, 6 deletions

diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 3674891902f..5e820fa91db 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -3936,16 +3936,21 @@
 #define  FDI_PORT_WIDTH_2X_LPT			(1<<19)
 #define  FDI_PORT_WIDTH_1X_LPT			(0<<19)
 
-#define _FDI_RXA_MISC            0xf0010
-#define _FDI_RXB_MISC            0xf1010
+#define _FDI_RXA_MISC			0xf0010
+#define _FDI_RXB_MISC			0xf1010
+#define  FDI_RX_PWRDN_LANE1_MASK	(3<<26)
+#define  FDI_RX_PWRDN_LANE1_VAL(x)	((x)<<26)
+#define  FDI_RX_PWRDN_LANE0_MASK	(3<<24)
+#define  FDI_RX_PWRDN_LANE0_VAL(x)	((x)<<24)
+#define  FDI_RX_TP1_TO_TP2_48		(2<<20)
+#define  FDI_RX_TP1_TO_TP2_64		(3<<20)
+#define  FDI_RX_FDI_DELAY_90		(0x90<<0)
+#define FDI_RX_MISC(pipe) _PIPE(pipe, _FDI_RXA_MISC, _FDI_RXB_MISC)
+
 #define _FDI_RXA_TUSIZE1         0xf0030
 #define _FDI_RXA_TUSIZE2         0xf0038
 #define _FDI_RXB_TUSIZE1         0xf1030
 #define _FDI_RXB_TUSIZE2         0xf1038
-#define  FDI_RX_TP1_TO_TP2_48	(2<<20)
-#define  FDI_RX_TP1_TO_TP2_64	(3<<20)
-#define  FDI_RX_FDI_DELAY_90	(0x90<<0)
-#define FDI_RX_MISC(pipe) _PIPE(pipe, _FDI_RXA_MISC, _FDI_RXB_MISC)
 #define FDI_RX_TUSIZE1(pipe) _PIPE(pipe, _FDI_RXA_TUSIZE1, _FDI_RXB_TUSIZE1)
 #define FDI_RX_TUSIZE2(pipe) _PIPE(pipe, _FDI_RXA_TUSIZE2, _FDI_RXB_TUSIZE2)