1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
|
ARM Linux 2.6
=============
Please check <ftp://ftp.arm.linux.org.uk/pub/armlinux> for
updates.
Compilation of kernel
---------------------
In order to compile ARM Linux, you will need a compiler capable of
generating ARM ELF code with GNU extensions. GCC 3.3 is known to be
a good compiler. Fortunately, you needn't guess. The kernel will report
an error if your compiler is a recognized offender.
To build ARM Linux natively, you shouldn't have to alter the ARCH = line
in the top level Makefile. However, if you don't have the ARM Linux ELF
tools installed as default, then you should change the CROSS_COMPILE
line as detailed below.
If you wish to cross-compile, then alter the following lines in the top
level make file:
ARCH = <whatever>
with
ARCH = arm
and
CROSS_COMPILE=
to
CROSS_COMPILE=<your-path-to-your-compiler-without-gcc>
eg.
CROSS_COMPILE=arm-linux-
Do a 'make config', followed by 'make Image' to build the kernel
(arch/arm/boot/Image). A compressed image can be built by doing a
'make zImage' instead of 'make Image'.
Bug reports etc
---------------
Please send patches to the patch system. For more information, see
http://www.arm.linux.org.uk/developer/patches/info.php Always include some
explanation as to what the patch does and why it is needed.
Bug reports should be sent to linux-arm-kernel@lists.arm.linux.org.uk,
or submitted through the web form at
http://www.arm.linux.org.uk/developer/
When sending bug reports, please ensure that they contain all relevant
information, eg. the kernel messages that were printed before/during
the problem, what you were doing, etc.
Include files
-------------
Several new include directories have been created under include/asm-arm,
which are there to reduce the clutter in the top-level directory. These
directories, and their purpose is listed below:
arch-* machine/platform specific header files
hardware driver-internal ARM specific data structures/definitions
mach descriptions of generic ARM to specific machine interfaces
proc-* processor dependent header files (currently only two
categories)
Machine/Platform support
------------------------
The ARM tree contains support for a lot of different machine types. To
continue supporting these differences, it has become necessary to split
machine-specific parts by directory. For this, the machine category is
used to select which directories and files get included (we will use
$(MACHINE) to refer to the category)
To this end, we now have arch/arm/mach-$(MACHINE) directories which are
designed to house the non-driver files for a particular machine (eg, PCI,
memory management, architecture definitions etc). For all future
machines, there should be a corresponding arch/arm/mach-$(MACHINE)/include/mach
directory.
Modules
-------
Although modularisation is supported (and required for the FP emulator),
each module on an ARM2/ARM250/ARM3 machine when is loaded will take
memory up to the next 32k boundary due to the size of the pages.
Therefore, is modularisation on these machines really worth it?
However, ARM6 and up machines allow modules to take multiples of 4k, and
as such Acorn RiscPCs and other architectures using these processors can
make good use of modularisation.
ADFS Image files
----------------
You can access image files on your ADFS partitions by mounting the ADFS
partition, and then using the loopback device driver. You must have
losetup installed.
Please note that the PCEmulator DOS partitions have a partition table at
the start, and as such, you will have to give '-o offset' to losetup.
Request to developers
---------------------
When writing device drivers which include a separate assembler file, please
include it in with the C file, and not the arch/arm/lib directory. This
allows the driver to be compiled as a loadable module without requiring
half the code to be compiled into the kernel image.
In general, try to avoid using assembler unless it is really necessary. It
makes drivers far less easy to port to other hardware.
ST506 hard drives
-----------------
The ST506 hard drive controllers seem to be working fine (if a little
slowly). At the moment they will only work off the controllers on an
A4x0's motherboard, but for it to work off a Podule just requires
someone with a podule to add the addresses for the IRQ mask and the
HDC base to the source.
As of 31/3/96 it works with two drives (you should get the ADFS
*configure harddrive set to 2). I've got an internal 20MB and a great
big external 5.25" FH 64MB drive (who could ever want more :-) ).
I've just got 240K/s off it (a dd with bs=128k); thats about half of what
RiscOS gets; but it's a heck of a lot better than the 50K/s I was getting
last week :-)
Known bug: Drive data errors can cause a hang; including cases where
the controller has fixed the error using ECC. (Possibly ONLY
in that case...hmm).
1772 Floppy
-----------
This also seems to work OK, but hasn't been stressed much lately. It
hasn't got any code for disc change detection in there at the moment which
could be a bit of a problem! Suggestions on the correct way to do this
are welcome.
CONFIG_MACH_ and CONFIG_ARCH_
-----------------------------
A change was made in 2003 to the macro names for new machines.
Historically, CONFIG_ARCH_ was used for the bonafide architecture,
e.g. SA1100, as well as implementations of the architecture,
e.g. Assabet. It was decided to change the implementation macros
to read CONFIG_MACH_ for clarity. Moreover, a retroactive fixup has
not been made because it would complicate patching.
Previous registrations may be found online.
<http://www.arm.linux.org.uk/developer/machines/>
Kernel entry (head.S)
--------------------------
The initial entry into the kernel is via head.S, which uses machine
independent code. The machine is selected by the value of 'r1' on
entry, which must be kept unique.
Due to the large number of machines which the ARM port of Linux provides
for, we have a method to manage this which ensures that we don't end up
duplicating large amounts of code.
We group machine (or platform) support code into machine classes. A
class typically based around one or more system on a chip devices, and
acts as a natural container around the actual implementations. These
classes are given directories - arch/arm/mach-<class> and
arch/arm/mach-<class> - which contain the source files to/include/mach
support the machine class. This directories also contain any machine
specific supporting code.
For example, the SA1100 class is based upon the SA1100 and SA1110 SoC
devices, and contains the code to support the way the on-board and off-
board devices are used, or the device is setup, and provides that
machine specific "personality."
This fine-grained machine specific selection is controlled by the machine
type ID, which acts both as a run-time and a compile-time code selection
method.
You can register a new machine via the web site at:
<http://www.arm.linux.org.uk/developer/machines/>
---
Russell King (15/03/2004)
|
