/* * Hardware definitions for Compaq iPAQ H3xxx Handheld Computers * * Copyright 2000,1 Compaq Computer Corporation. * * Use consistent with the GNU GPL is permitted, * provided that this copyright notice is * preserved in its entirety in all copies and derived works. * * COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, * AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS * FITNESS FOR ANY PARTICULAR PURPOSE. * * Author: Jamey Hicks. * * History: * * 2001-10-?? Andrew Christian Added support for iPAQ H3800 * and abstracted EGPIO interface. * */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "generic.h" void (*assign_h3600_egpio)(enum ipaq_egpio_type x, int level); EXPORT_SYMBOL(assign_h3600_egpio); static struct mtd_partition h3xxx_partitions[] = { { .name = "H3XXX boot firmware", .size = 0x00040000, .offset = 0, .mask_flags = MTD_WRITEABLE, /* force read-only */ }, { .name = "H3XXX rootfs", .size = MTDPART_SIZ_FULL, .offset = 0x00040000, } }; static void h3xxx_set_vpp(int vpp) { assign_h3600_egpio(IPAQ_EGPIO_VPP_ON, vpp); } static struct flash_platform_data h3xxx_flash_data = { .map_name = "cfi_probe", .set_vpp = h3xxx_set_vpp, .parts = h3xxx_partitions, .nr_parts = ARRAY_SIZE(h3xxx_partitions), }; static struct resource h3xxx_flash_resource = { .start = SA1100_CS0_PHYS, .end = SA1100_CS0_PHYS + SZ_32M - 1, .flags = IORESOURCE_MEM, }; /* * This turns the IRDA power on or off on the Compaq H3600 */ static int h3600_irda_set_power(struct device *dev, unsigned int state) { assign_h3600_egpio( IPAQ_EGPIO_IR_ON, state ); return 0; } static void h3600_irda_set_speed(struct device *dev, unsigned int speed) { assign_h3600_egpio(IPAQ_EGPIO_IR_FSEL, !(speed < 4000000)); } static struct irda_platform_data h3600_irda_data = { .set_power = h3600_irda_set_power, .set_speed = h3600_irda_set_speed, }; static void h3xxx_mach_init(void) { sa11x0_set_flash_data(&h3xxx_flash_data, &h3xxx_flash_resource, 1); sa11x0_set_irda_data(&h3600_irda_data); } /* * low-level UART features */ static void h3600_uart_set_mctrl(struct uart_port *port, u_int mctrl) { if (port->mapbase == _Ser3UTCR0) { if (mctrl & TIOCM_RTS) GPCR = GPIO_H3600_COM_RTS; else GPSR = GPIO_H3600_COM_RTS; } } static u_int h3600_uart_get_mctrl(struct uart_port *port) { u_int ret = TIOCM_CD | TIOCM_CTS | TIOCM_DSR; if (port->mapbase == _Ser3UTCR0) { int gplr = GPLR; /* DCD and CTS bits are inverted in GPLR by RS232 transceiver */ if (gplr & GPIO_H3600_COM_DCD) ret &= ~TIOCM_CD; if (gplr & GPIO_H3600_COM_CTS) ret &= ~TIOCM_CTS; } return ret; } static void h3600_uart_pm(struct uart_port *port, u_int state, u_int oldstate) { if (port->mapbase == _Ser2UTCR0) { /* TODO: REMOVE THIS */ assign_h3600_egpio(IPAQ_EGPIO_IR_ON, !state); } else if (port->mapbase == _Ser3UTCR0) { assign_h3600_egpio(IPAQ_EGPIO_RS232_ON, !state); } } /* * Enable/Disable wake up events for this serial port. * Obviously, we only support this on the normal COM port. */ static int h3600_uart_set_wake(struct uart_port *port, u_int enable) { int err = -EINVAL; if (port->mapbase == _Ser3UTCR0) { if (enable) PWER |= PWER_GPIO23 | PWER_GPIO25; /* DCD and CTS */ else PWER &= ~(PWER_GPIO23 | PWER_GPIO25); /* DCD and CTS */ err = 0; } return err; } static struct sa1100_port_fns h3600_port_fns __initdata = { .set_mctrl = h3600_uart_set_mctrl, .get_mctrl = h3600_uart_get_mctrl, .pm = h3600_uart_pm, .set_wake = h3600_uart_set_wake, }; /* * helper for sa1100fb */ static void h3xxx_lcd_power(int enable) { assign_h3600_egpio(IPAQ_EGPIO_LCD_POWER, enable); } static struct map_desc h3600_io_desc[] __initdata = { { /* static memory bank 2 CS#2 */ .virtual = H3600_BANK_2_VIRT, .pfn = __phys_to_pfn(SA1100_CS2_PHYS), .length = 0x02800000, .type = MT_DEVICE }, { /* static memory bank 4 CS#4 */ .virtual = H3600_BANK_4_VIRT, .pfn = __phys_to_pfn(SA1100_CS4_PHYS), .length = 0x00800000, .type = MT_DEVICE }, { /* EGPIO 0 CS#5 */ .virtual = H3600_EGPIO_VIRT, .pfn = __phys_to_pfn(H3600_EGPIO_PHYS), .length = 0x01000000, .type = MT_DEVICE } }; /* * Common map_io initialization */ static void __init h3xxx_map_io(void) { sa1100_map_io(); iotable_init(h3600_io_desc, ARRAY_SIZE(h3600_io_desc)); sa1100_register_uart_fns(&h3600_port_fns); sa1100_register_uart(0, 3); /* Common serial port */ // sa1100_register_uart(1, 1); /* Microcontroller on 3100/3600 */ /* Ensure those pins are outputs and driving low */ PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM; PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM); /* Configure suspend conditions */ PGSR = 0; PWER = PWER_GPIO0 | PWER_RTC; PCFR = PCFR_OPDE; PSDR = 0; sa1100fb_lcd_power = h3xxx_lcd_power; } /************************* H3100 *************************/ #ifdef CONFIG_SA1100_H3100 #define H3100_EGPIO (*(volatile unsigned int *)H3600_EGPIO_VIRT) static unsigned int h3100_egpio = 0; static void h3100_control_egpio(enum ipaq_egpio_type x, int setp) { unsigned int egpio = 0; long gpio = 0; unsigned long flags; switch (x) { case IPAQ_EGPIO_LCD_POWER: egpio |= EGPIO_H3600_LCD_ON; gpio |= GPIO_H3100_LCD_3V_ON; break; case IPAQ_EGPIO_LCD_ENABLE: break; case IPAQ_EGPIO_CODEC_NRESET: egpio |= EGPIO_H3600_CODEC_NRESET; break; case IPAQ_EGPIO_AUDIO_ON: gpio |= GPIO_H3100_AUD_PWR_ON | GPIO_H3100_AUD_ON; break; case IPAQ_EGPIO_QMUTE: gpio |= GPIO_H3100_QMUTE; break; case IPAQ_EGPIO_OPT_NVRAM_ON: egpio |= EGPIO_H3600_OPT_NVRAM_ON; break; case IPAQ_EGPIO_OPT_ON: egpio |= EGPIO_H3600_OPT_ON; break; case IPAQ_EGPIO_CARD_RESET: egpio |= EGPIO_H3600_CARD_RESET; break; case IPAQ_EGPIO_OPT_RESET: egpio |= EGPIO_H3600_OPT_RESET; break; case IPAQ_EGPIO_IR_ON: gpio |= GPIO_H3100_IR_ON; break; case IPAQ_EGPIO_IR_FSEL: gpio |= GPIO_H3100_IR_FSEL; break; case IPAQ_EGPIO_RS232_ON: egpio |= EGPIO_H3600_RS232_ON; break; case IPAQ_EGPIO_VPP_ON: egpio |= EGPIO_H3600_VPP_ON; break; } if (egpio || gpio) { local_irq_save(flags); if (setp) { h3100_egpio |= egpio; GPSR = gpio; } else { h3100_egpio &= ~egpio; GPCR = gpio; } H3100_EGPIO = h3100_egpio; local_irq_restore(flags); } } #define H3100_DIRECT_EGPIO (GPIO_H3100_BT_ON \ | GPIO_H3100_GPIO3 \ | GPIO_H3100_QMUTE \ | GPIO_H3100_LCD_3V_ON \ | GPIO_H3100_AUD_ON \ | GPIO_H3100_AUD_PWR_ON \ | GPIO_H3100_IR_ON \ | GPIO_H3100_IR_FSEL) static void __init h3100_map_io(void) { h3xxx_map_io(); /* Initialize h3100-specific values here */ GPCR = 0x0fffffff; /* All outputs are set low by default */ GPDR = GPIO_H3600_COM_RTS | GPIO_H3600_L3_CLOCK | GPIO_H3600_L3_MODE | GPIO_H3600_L3_DATA | GPIO_H3600_CLK_SET1 | GPIO_H3600_CLK_SET0 | H3100_DIRECT_EGPIO; /* Older bootldrs put GPIO2-9 in alternate mode on the assumption that they are used for video */ GAFR &= ~H3100_DIRECT_EGPIO; H3100_EGPIO = h3100_egpio; assign_h3600_egpio = h3100_control_egpio; } MACHINE_START(H3100, "Compaq iPAQ H3100") .phys_io = 0x80000000, .io_pg_offst = ((0xf8000000) >> 18) & 0xfffc, .boot_params = 0xc0000100, .map_io = h3100_map_io, .init_irq = sa1100_init_irq, .timer = &sa1100_timer, .init_machine = h3xxx_mach_init, MACHINE_END #endif /* CONFIG_SA1100_H3100 */ /************************* H3600 *************************/ #ifdef CONFIG_SA1100_H3600 #define H3600_EGPIO (*(volatile unsigned int *)H3600_EGPIO_VIRT) static unsigned int h3600_egpio = EGPIO_H3600_RS232_ON; static void h3600_control_egpio(enum ipaq_egpio_type x, int setp) { unsigned int egpio = 0; unsigned long flags; switch (x) { case IPAQ_EGPIO_LCD_POWER: egpio |= EGPIO_H3600_LCD_ON | EGPIO_H3600_LCD_PCI | EGPIO_H3600_LCD_5V_ON | EGPIO_H3600_LVDD_ON; break; case IPAQ_EGPIO_LCD_ENABLE: break; case IPAQ_EGPIO_CODEC_NRESET: egpio |= EGPIO_H3600_CODEC_NRESET; break; case IPAQ_EGPIO_AUDIO_ON: egpio |= EGPIO_H3600_AUD_AMP_ON | EGPIO_H3600_AUD_PWR_ON; break; case IPAQ_EGPIO_QMUTE: egpio |= EGPIO_H3600_QMUTE; break; case IPAQ_EGPIO_OPT_NVRAM_ON: egpio |= EGPIO_H3600_OPT_NVRAM_ON; break; case IPAQ_EGPIO_OPT_ON: egpio |= EGPIO_H3600_OPT_ON; break; case IPAQ_EGPIO_CARD_RESET: egpio |= EGPIO_H3600_CARD_RESET; break; case IPAQ_EGPIO_OPT_RESET: egpio |= EGPIO_H3600_OPT_RESET; break; case IPAQ_EGPIO_IR_ON: egpio |= EGPIO_H3600_IR_ON; break; case IPAQ_EGPIO_IR_FSEL: egpio |= EGPIO_H3600_IR_FSEL; break; case IPAQ_EGPIO_RS232_ON: egpio |= EGPIO_H3600_RS232_ON; break; case IPAQ_EGPIO_VPP_ON: egpio |= EGPIO_H3600_VPP_ON; break; } if (egpio) { local_irq_save(flags); if (setp) h3600_egpio |= egpio; else h3600_egpio &= ~egpio; H3600_EGPIO = h3600_egpio; local_irq_restore(flags); } } static void __init h3600_map_io(void) { h3xxx_map_io(); /* Initialize h3600-specific values here */ GPCR = 0x0fffffff; /* All outputs are set low by default */ GPDR = GPIO_H3600_COM_RTS | GPIO_H3600_L3_CLOCK | GPIO_H3600_L3_MODE | GPIO_H3600_L3_DATA | GPIO_H3600_CLK_SET1 | GPIO_H3600_CLK_SET0 | GPIO_LDD15 | GPIO_LDD14 | GPIO_LDD13 | GPIO_LDD12 | GPIO_LDD11 | GPIO_LDD10 | GPIO_LDD9 | GPIO_LDD8; H3600_EGPIO = h3600_egpio; /* Maintains across sleep? */ assign_h3600_egpio = h3600_control_egpio; } MACHINE_START(H3600, "Compaq iPAQ H3600") .phys_io = 0x80000000, .io_pg_offst = ((0xf8000000) >> 18) & 0xfffc, .boot_params = 0xc0000100, .map_io = h3600_map_io, .init_irq = sa1100_init_irq, .timer = &sa1100_timer, .init_machine = h3xxx_mach_init, MACHINE_END #endif /* CONFIG_SA1100_H3600 */