From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- .../arm/Sharp-LH/VectoredInterruptController | 80 ++++++++++++++++++++++ 1 file changed, 80 insertions(+) create mode 100644 Documentation/arm/Sharp-LH/VectoredInterruptController (limited to 'Documentation/arm/Sharp-LH/VectoredInterruptController') diff --git a/Documentation/arm/Sharp-LH/VectoredInterruptController b/Documentation/arm/Sharp-LH/VectoredInterruptController new file mode 100644 index 00000000000..23047e9861e --- /dev/null +++ b/Documentation/arm/Sharp-LH/VectoredInterruptController @@ -0,0 +1,80 @@ +README on the Vectored Interrupt Controller of the LH7A404 +========================================================== + +The 404 revision of the LH7A40X series comes with two vectored +interrupts controllers. While the kernel does use some of the +features of these devices, it is far from the purpose for which they +were designed. + +When this README was written, the implementation of the VICs was in +flux. It is possible that some details, especially with priorities, +will change. + +The VIC support code is inspired by routines written by Sharp. + + +Priority Control +---------------- + +The significant reason for using the VIC's vectoring is to control +interrupt priorities. There are two tables in +arch/arm/mach-lh7a40x/irq-lh7a404.c that look something like this. + + static unsigned char irq_pri_vic1[] = { IRQ_GPIO3INTR, }; + static unsigned char irq_pri_vic2[] = { + IRQ_T3UI, IRQ_GPIO7INTR, + IRQ_UART1INTR, IRQ_UART2INTR, IRQ_UART3INTR, }; + +The initialization code reads these tables and inserts a vector +address and enable for each indicated IRQ. Vectored interrupts have +higher priority than non-vectored interrupts. So, on VIC1, +IRQ_GPIO3INTR will be served before any other non-FIQ interrupt. Due +to the way that the vectoring works, IRQ_T3UI is the next highest +priority followed by the other vectored interrupts on VIC2. After +that, the non-vectored interrupts are scanned in VIC1 then in VIC2. + + +ISR +--- + +The interrupt service routine macro get_irqnr() in +arch/arm/kernel/entry-armv.S scans the VICs for the next active +interrupt. The vectoring makes this code somewhat larger than it was +before using vectoring (refer to the LH7A400 implementation). In the +case where an interrupt is vectored, the implementation will tend to +be faster than the non-vectored version. However, the worst-case path +is longer. + +It is worth noting that at present, there is no need to read +VIC2_VECTADDR because the register appears to be shared between the +controllers. The code is written such that if this changes, it ought +to still work properly. + + +Vector Addresses +---------------- + +The proper use of the vectoring hardware would jump to the ISR +specified by the vectoring address. Linux isn't structured to take +advantage of this feature, though it might be possible to change +things to support it. + +In this implementation, the vectoring address is used to speed the +search for the active IRQ. The address is coded such that the lowest +6 bits store the IRQ number for vectored interrupts. These numbers +correspond to the bits in the interrupt status registers. IRQ zero is +the lowest interrupt bit in VIC1. IRQ 32 is the lowest interrupt bit +in VIC2. Because zero is a valid IRQ number and because we cannot +detect whether or not there is a valid vectoring address if that +address is zero, the eigth bit (0x100) is set for vectored interrupts. +The address for IRQ 0x18 (VIC2) is 0x118. Only the ninth bit is set +for the default handler on VIC1 and only the tenth bit is set for the +default handler on VIC2. + +In other words. + + 0x000 - no active interrupt + 0x1ii - vectored interrupt 0xii + 0x2xx - unvectored interrupt on VIC1 (xx is don't care) + 0x4xx - unvectored interrupt on VIC2 (xx is don't care) + -- cgit v1.2.3