| Age | Commit message (Collapse) | Author |
|---|
|
MPC8308 has ULPI pin muxing settings in SICRH register, bits 17-18
which is different from both MPC8313 and MPC8315.
Also MPC8308 doesn't have REFSEL, UTMI_PHY_EN and OTG_PORT fields
in the USB DR controller CONTROL register.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Actually, the support is already there, but it requires newer U-Boots
(to fill-in clock-frequency, and setup pin multiplexing).
Though, it appears that on RDB boards USBB pins aren't multiplexed
between USB and eSDHC (unlike MDS boards, where USB and eSDHC share
pctl and pwrfault pins).
So, for RDB boards we can safely setup pinmux and manually fill-in
clock-frequency, thus making eSDHC work even with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.
The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..
mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.
Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch fixes following sparse warnings:
CHECK 83xx/usb.c
83xx/usb.c:205:5: warning: symbol 'mpc837x_usb_cfg' was not declared. Should it be static?
CHECK 83xx/mpc831x_rdb.c
83xx/mpc831x_rdb.c:45:13: warning: symbol 'mpc831x_rdb_init_IRQ' was not declared. Should it be static?
CHECK 83xx/mpc832x_rdb.c
83xx/mpc832x_rdb.c:133:13: warning: symbol 'mpc832x_rdb_init_IRQ' was not declared. Should it be static?
CHECK 83xx/mpc832x_mds.c
83xx/mpc832x_mds.c:68:12: warning: Using plain integer as NULL pointer
83xx/mpc832x_mds.c:72:13: warning: incorrect type in assignment (different address spaces)
83xx/mpc832x_mds.c:72:13: expected unsigned char [usertype] *static [toplevel] bcsr_regs
83xx/mpc832x_mds.c:72:13: got void [noderef] <asn:2>*
83xx/mpc832x_mds.c:99:11: warning: incorrect type in argument 1 (different address spaces)
83xx/mpc832x_mds.c:99:11: expected void volatile [noderef] <asn:2>*addr
83xx/mpc832x_mds.c:99:11: got unsigned char [usertype] *static [toplevel] bcsr_regs
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
We must not use MPC831X_SICR[HL]_* definitions for the MPC8315 processors,
because SICR USB bits locations are not compatible with MPC8313.
This patch fixes ULPI workability on MPC8315E-RDB boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This allows other platforms with the same pci block like MPC5121 to use it.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Currently USB Host isn't functional on the MPC8315E boards, for two
reasons as described below.
MPC8315 Reference Manual says:
"The USB DR unit must have the same clock ratio as the encryption core
unit, unless one of them has its clock disabled."
The encryption core also drives I2C clock, so it is enabled and is equal
to 01. That means USBDRCM should be 01 here.
Plus, according to MPC8315E-RDB schematics, USB unit consumes CLK_IN
clock from the 24.00MHz oscillator, which means we must adjust REFSEL
bits as well.
p.s.
Idially we should rework whole 83xx/usb.c code, in two steps:
1. Move SCCR code to the U-Boot;
2. Implement fsl,usb-clock property in the device tree, so usb.c could
decide what clock exactly to use on per-board basis.
Though, today we're not in a hurry since there is just one 8315e board
out there.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
SCCR USB bits are in a different location on the mpc8315.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add chip specific and board specific initialization for MPC837x USB.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Now that the generic code doesn't assign resources for Freescale
PHBs we dont have to explicitly exclude it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add 831x USB platform setup code and rework 834x USB platform setup code.
Move USB platform code to usb.c for different boards with CPU of the same
series to share the USB initialization code.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add board specific initialization code for USB to work in both MPH and DR
mode for MPC8349E MDS-PB board.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This fixes MPC834x MDS (formerly SYS) and ITX platform code to get IRQ data (including PCI) from the device tree, and to use the new IPIC code.
renamed defconfig (sys -> mds), left one redundant NULL assignment in mpc83xx_pcibios_fixup to keep the compiler happy.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Ran arch/powerpc/platforms/83xx through Lindent
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Moved some code around so its usable by more systems than just
the MPC834x SYS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add the first MPC83xx board that uses a flat device tree to arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
