diff options
Diffstat (limited to 'Documentation/hwmon/sysfs-interface')
| -rw-r--r-- | Documentation/hwmon/sysfs-interface | 51 |
1 files changed, 42 insertions, 9 deletions
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index d4e2917c6f1..64569901055 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -91,12 +91,11 @@ name The chip name. I2C devices get this attribute created automatically. RO -update_rate The rate at which the chip will update readings. +update_interval The interval at which the chip will update readings. Unit: millisecond RW - Some devices have a variable update rate. This attribute - can be used to change the update rate to the desired - frequency. + Some devices have a variable update rate or interval. + This attribute can be used to change it to the desired value. ************ @@ -107,10 +106,24 @@ in[0-*]_min Voltage min value. Unit: millivolt RW +in[0-*]_lcrit Voltage critical min value. + Unit: millivolt + RW + If voltage drops to or below this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + in[0-*]_max Voltage max value. Unit: millivolt RW +in[0-*]_crit Voltage critical max value. + Unit: millivolt + RW + If voltage reaches or exceeds this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + in[0-*]_input Voltage input value. Unit: millivolt RO @@ -284,7 +297,7 @@ temp[1-*]_input Temperature input value. Unit: millidegree Celsius RO -temp[1-*]_crit Temperature critical value, typically greater than +temp[1-*]_crit Temperature critical max value, typically greater than corresponding temp_max values. Unit: millidegree Celsius RW @@ -296,6 +309,25 @@ temp[1-*]_crit_hyst from the critical value. RW +temp[1-*]_emergency + Temperature emergency max value, for chips supporting more than + two upper temperature limits. Must be equal or greater than + corresponding temp_crit values. + Unit: millidegree Celsius + RW + +temp[1-*]_emergency_hyst + Temperature hysteresis value for emergency limit. + Unit: millidegree Celsius + Must be reported as an absolute temperature, NOT a delta + from the emergency value. + RW + +temp[1-*]_lcrit Temperature critical min value, typically lower than + corresponding temp_min values. + Unit: millidegree Celsius + RW + temp[1-*]_offset Temperature offset which is added to the temperature reading by the chip. @@ -344,9 +376,6 @@ Also see the Alarms section for status flags associated with temperatures. * Currents * ************ -Note that no known chip provides current measurements as of writing, -so this part is theoretical, so to say. - curr[1-*]_max Current max value Unit: milliampere RW @@ -471,6 +500,7 @@ limit-related alarms, not both. The driver should just reflect the hardware implementation. in[0-*]_alarm +curr[1-*]_alarm fan[1-*]_alarm temp[1-*]_alarm Channel alarm @@ -482,11 +512,14 @@ OR in[0-*]_min_alarm in[0-*]_max_alarm +curr[1-*]_min_alarm +curr[1-*]_max_alarm fan[1-*]_min_alarm fan[1-*]_max_alarm temp[1-*]_min_alarm temp[1-*]_max_alarm temp[1-*]_crit_alarm +temp[1-*]_emergency_alarm Limit alarm 0: no alarm 1: alarm @@ -497,7 +530,6 @@ to notify open diodes, unconnected fans etc. where the hardware supports it. When this boolean has value 1, the measurement for that channel should not be trusted. -in[0-*]_fault fan[1-*]_fault temp[1-*]_fault Input fault condition @@ -513,6 +545,7 @@ beep_enable Master beep enable RW in[0-*]_beep +curr[1-*]_beep fan[1-*]_beep temp[1-*]_beep Channel beep |