1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
|
/*
* pata_opti.c - ATI PATA for new ATA layer
* (C) 2005 Red Hat Inc
*
* Based on
* linux/drivers/ide/pci/opti621.c Version 0.7 Sept 10, 2002
*
* Copyright (C) 1996-1998 Linus Torvalds & authors (see below)
*
* Authors:
* Jaromir Koutek <miri@punknet.cz>,
* Jan Harkes <jaharkes@cwi.nl>,
* Mark Lord <mlord@pobox.com>
* Some parts of code are from ali14xx.c and from rz1000.c.
*
* Also consulted the FreeBSD prototype driver by Kevin Day to try
* and resolve some confusions. Further documentation can be found in
* Ralf Brown's interrupt list
*
* If you have other variants of the Opti range (Viper/Vendetta) please
* try this driver with those PCI idents and report back. For the later
* chips see the pata_optidma driver
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_opti"
#define DRV_VERSION "0.2.9"
enum {
READ_REG = 0, /* index of Read cycle timing register */
WRITE_REG = 1, /* index of Write cycle timing register */
CNTRL_REG = 3, /* index of Control register */
STRAP_REG = 5, /* index of Strap register */
MISC_REG = 6 /* index of Miscellaneous register */
};
/**
* opti_pre_reset - probe begin
* @link: ATA link
* @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
static int opti_pre_reset(struct ata_link *link, unsigned long deadline)
{
struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits opti_enable_bits[] = {
{ 0x45, 1, 0x80, 0x00 },
{ 0x40, 1, 0x08, 0x00 }
};
if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no]))
return -ENOENT;
return ata_sff_prereset(link, deadline);
}
/**
* opti_write_reg - control register setup
* @ap: ATA port
* @value: value
* @reg: control register number
*
* The Opti uses magic 'trapdoor' register accesses to do configuration
* rather than using PCI space as other controllers do. The double inw
* on the error register activates configuration mode. We can then write
* the control register
*/
static void opti_write_reg(struct ata_port *ap, u8 val, int reg)
{
void __iomem *regio = ap->ioaddr.cmd_addr;
/* These 3 unlock the control register access */
ioread16(regio + 1);
ioread16(regio + 1);
iowrite8(3, regio + 2);
/* Do the I/O */
iowrite8(val, regio + reg);
/* Relock */
iowrite8(0x83, regio + 2);
}
/**
* opti_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the PIO mode setup. Timing numbers are taken from
* the FreeBSD driver then pre computed to keep the code clean. There
* are two tables depending on the hardware clock speed.
*/
static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
struct ata_device *pair = ata_dev_pair(adev);
int clock;
int pio = adev->pio_mode - XFER_PIO_0;
void __iomem *regio = ap->ioaddr.cmd_addr;
u8 addr;
/* Address table precomputed with prefetch off and a DCLK of 2 */
static const u8 addr_timing[2][5] = {
{ 0x30, 0x20, 0x20, 0x10, 0x10 },
{ 0x20, 0x20, 0x10, 0x10, 0x10 }
};
static const u8 data_rec_timing[2][5] = {
{ 0x6B, 0x56, 0x42, 0x32, 0x31 },
{ 0x58, 0x44, 0x32, 0x22, 0x21 }
};
iowrite8(0xff, regio + 5);
clock = ioread16(regio + 5) & 1;
/*
* As with many controllers the address setup time is shared
* and must suit both devices if present.
*/
addr = addr_timing[clock][pio];
if (pair) {
/* Hardware constraint */
u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0];
if (pair_addr > addr)
addr = pair_addr;
}
/* Commence primary programming sequence */
opti_write_reg(ap, adev->devno, MISC_REG);
opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG);
opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG);
opti_write_reg(ap, addr, MISC_REG);
/* Programming sequence complete, override strapping */
opti_write_reg(ap, 0x85, CNTRL_REG);
}
static struct scsi_host_template opti_sht = {
ATA_PIO_SHT(DRV_NAME),
};
static struct ata_port_operations opti_port_ops = {
.inherits = &ata_sff_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = opti_set_piomode,
.prereset = opti_pre_reset,
};
static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.port_ops = &opti_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
static int printed_version;
if (!printed_version++)
dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL, 0);
}
static const struct pci_device_id opti[] = {
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
{ },
};
static struct pci_driver opti_pci_driver = {
.name = DRV_NAME,
.id_table = opti,
.probe = opti_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
static int __init opti_init(void)
{
return pci_register_driver(&opti_pci_driver);
}
static void __exit opti_exit(void)
{
pci_unregister_driver(&opti_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Opti 621/621X");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, opti);
MODULE_VERSION(DRV_VERSION);
module_init(opti_init);
module_exit(opti_exit);
|
