/************************************************************************/ /* */ /* dc395x.h */ /* */ /* Device Driver for Tekram DC395(U/UW/F), DC315(U) */ /* PCI SCSI Bus Master Host Adapter */ /* (SCSI chip set used Tekram ASIC TRM-S1040) */ /* */ /************************************************************************/ #ifndef DC395x_H #define DC395x_H /************************************************************************/ /* */ /* Initial values */ /* */ /************************************************************************/ #define DC395x_MAX_CMD_QUEUE 32 /* #define DC395x_MAX_QTAGS 32 */ #define DC395x_MAX_QTAGS 16 #define DC395x_MAX_SCSI_ID 16 #define DC395x_MAX_CMD_PER_LUN DC395x_MAX_QTAGS #define DC395x_MAX_SG_TABLESIZE 64 /* HW limitation */ #define DC395x_MAX_SG_LISTENTRY 64 /* Must be equal or lower to previous */ /* item */ #define DC395x_MAX_SRB_CNT 63 /* #define DC395x_MAX_CAN_QUEUE 7 * DC395x_MAX_QTAGS */ #define DC395x_MAX_CAN_QUEUE DC395x_MAX_SRB_CNT #define DC395x_END_SCAN 2 #define DC395x_SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */ #define DC395x_MAX_RETRIES 3 #if 0 #define SYNC_FIRST #endif #define NORM_REC_LVL 0 /************************************************************************/ /* */ /* Various definitions */ /* */ /************************************************************************/ #define BIT31 0x80000000 #define BIT30 0x40000000 #define BIT29 0x20000000 #define BIT28 0x10000000 #define BIT27 0x08000000 #define BIT26 0x04000000 #define BIT25 0x02000000 #define BIT24 0x01000000 #define BIT23 0x00800000 #define BIT22 0x00400000 #define BIT21 0x00200000 #define BIT20 0x00100000 #define BIT19 0x00080000 #define BIT18 0x00040000 #define BIT17 0x00020000 #define BIT16 0x00010000 #define BIT15 0x00008000 #define BIT14 0x00004000 #define BIT13 0x00002000 #define BIT12 0x00001000 #define BIT11 0x00000800 #define BIT10 0x00000400 #define BIT9 0x00000200 #define BIT8 0x00000100 #define BIT7 0x00000080 #define BIT6 0x00000040 #define BIT5 0x00000020 #define BIT4 0x00000010 #define BIT3 0x00000008 #define BIT2 0x00000004 #define BIT1 0x00000002 #define BIT0 0x00000001 /* UnitCtrlFlag */ #define UNIT_ALLOCATED BIT0 #define UNIT_INFO_CHANGED BIT1 #define FORMATING_MEDIA BIT2 #define UNIT_RETRY BIT3 /* UnitFlags */ #define DASD_SUPPORT BIT0 #define SCSI_SUPPORT BIT1 #define ASPI_SUPPORT BIT2 /* SRBState machine definition */ #define SRB_FREE 0x0000 #define SRB_WAIT 0x0001 #define SRB_READY 0x0002 #define SRB_MSGOUT 0x0004 /* arbitration+msg_out 1st byte */ #define SRB_MSGIN 0x0008 #define SRB_EXTEND_MSGIN 0x0010 #define SRB_COMMAND 0x0020 #define SRB_START_ 0x0040 /* arbitration+msg_out+command_out */ #define SRB_DISCONNECT 0x0080 #define SRB_DATA_XFER 0x0100 #define SRB_XFERPAD 0x0200 #define SRB_STATUS 0x0400 #define SRB_COMPLETED 0x0800 #define SRB_ABORT_SENT 0x1000 #define SRB_DO_SYNC_NEGO 0x2000 #define SRB_DO_WIDE_NEGO 0x4000 #define SRB_UNEXPECT_RESEL 0x8000 /************************************************************************/ /* */ /* ACB Config */ /* */ /************************************************************************/ #define HCC_WIDE_CARD 0x20 #define HCC_SCSI_RESET 0x10 #define HCC_PARITY 0x08 #define HCC_AUTOTERM 0x04 #define HCC_LOW8TERM 0x02 #define HCC_UP8TERM 0x01 /* ACBFlag */ #define RESET_DEV BIT0 #define RESET_DETECT BIT1 #define RESET_DONE BIT2 /* DCBFlag */ #define ABORT_DEV_ BIT0 /* SRBstatus */ #define SRB_OK BIT0 #define ABORTION BIT1 #define OVER_RUN BIT2 #define UNDER_RUN BIT3 #define PARITY_ERROR BIT4 #define SRB_ERROR BIT5 /* SRBFlag */ #define DATAOUT BIT7 #define DATAIN BIT6 #define RESIDUAL_VALID BIT5 #define ENABLE_TIMER BIT4 #define RESET_DEV0 BIT2 #define ABORT_DEV BIT1 #define AUTO_REQSENSE BIT0 /* Adapter status */ #define H_STATUS_GOOD 0 #define H_SEL_TIMEOUT 0x11 #define H_OVER_UNDER_RUN 0x12 #define H_UNEXP_BUS_FREE 0x13 #define H_TARGET_PHASE_F 0x14 #define H_INVALID_CCB_OP 0x16 #define H_LINK_CCB_BAD 0x17 #define H_BAD_TARGET_DIR 0x18 #define H_DUPLICATE_CCB 0x19 #define H_BAD_CCB_OR_SG 0x1A #define H_ABORT 0x0FF /* SCSI BUS Status byte codes */ #define SCSI_STAT_GOOD 0x0 /* Good status */ #define SCSI_STAT_CHECKCOND 0x02 /* SCSI Check Condition */ #define SCSI_STAT_CONDMET 0x04 /* Condition Met */ #define SCSI_STAT_BUSY 0x08 /* Target busy status */ #define SCSI_STAT_INTER 0x10 /* Intermediate status */ #define SCSI_STAT_INTERCONDMET 0x14 /* Intermediate condition met */ #define SCSI_STAT_RESCONFLICT 0x18 /* Reservation conflict */ #define SCSI_STAT_CMDTERM 0x22 /* Command Terminated */ #define SCSI_STAT_QUEUEFULL 0x28 /* Queue Full */ #define SCSI_STAT_UNEXP_BUS_F 0xFD /* Unexpect Bus Free */ #define SCSI_STAT_BUS_RST_DETECT 0xFE /* Scsi Bus Reset detected */ #define SCSI_STAT_SEL_TIMEOUT 0xFF /* Selection Time out */ /* Sync_Mode */ #define SYNC_WIDE_TAG_ATNT_DISABLE 0 #define SYNC_NEGO_ENABLE BIT0 #define SYNC_NEGO_DONE BIT1 #define WIDE_NEGO_ENABLE BIT2 #define WIDE_NEGO_DONE BIT3 #define WIDE_NEGO_STATE BIT4 #define EN_TAG_QUEUEING BIT5 #define EN_ATN_STOP BIT6 #define SYNC_NEGO_OFFSET 15 /* SCSI MSG BYTE */ #define MSG_COMPLETE 0x00 #define MSG_EXTENDED 0x01 #define MSG_SAVE_PTR 0x02 #define MSG_RESTORE_PTR 0x03 #define MSG_DISCONNECT 0x04 #define MSG_INITIATOR_ERROR 0x05 #define MSG_ABORT 0x06 #define MSG_REJECT_ 0x07 #define MSG_NOP 0x08 #define MSG_PARITY_ERROR 0x09 #define MSG_LINK_CMD_COMPL 0x0A #define MSG_LINK_CMD_COMPL_FLG 0x0B #define MSG_BUS_RESET 0x0C #define MSG_ABORT_TAG 0x0D #define MSG_SIMPLE_QTAG 0x20 #define MSG_HEAD_QTAG 0x21 #define MSG_ORDER_QTAG 0x22 #define MSG_IGNOREWIDE 0x23 #define MSG_IDENTIFY 0x80 #define MSG_HOST_ID 0xC0 /* SCSI STATUS BYTE */ #define STATUS_GOOD 0x00 #define CHECK_CONDITION_ 0x02 #define STATUS_BUSY 0x08 #define STATUS_INTERMEDIATE 0x10 #define RESERVE_CONFLICT 0x18 /* cmd->result */ #define STATUS_MASK_ 0xFF #define MSG_MASK 0xFF00 #define RETURN_MASK 0xFF0000 /************************************************************************/ /* */ /* Inquiry Data format */ /* */ /************************************************************************/ struct ScsiInqData { /* INQ */ u8 DevType; /* Periph Qualifier & Periph Dev Type */ u8 RMB_TypeMod; /* rem media bit & Dev Type Modifier */ u8 Vers; /* ISO, ECMA, & ANSI versions */ u8 RDF; /* AEN, TRMIOP, & response data format */ u8 AddLen; /* length of additional data */ u8 Res1; /* reserved */ u8 Res2; /* reserved */ u8 Flags; /* RelADr, Wbus32, Wbus16, Sync, etc. */ u8 VendorID[8]; /* Vendor Identification */ u8 ProductID[16]; /* Product Identification */ u8 ProductRev[4]; /* Product Revision */ }; /* Inquiry byte 0 masks */ #define SCSI_DEVTYPE 0x1F /* Peripheral Device Type */ #define SCSI_PERIPHQUAL 0xE0 /* Peripheral Qualifier */ /* Inquiry byte 1 mask */ #define SCSI_REMOVABLE_MEDIA 0x80 /* Removable Media bit (1=removable) */ /* Peripheral Device Type definitions */ /* See include/scsi/scsi.h */ #define TYPE_NODEV SCSI_DEVTYPE /* Unknown or no device type */ #ifndef TYPE_PRINTER /* */ # define TYPE_PRINTER 0x02 /* Printer device */ #endif /* */ #ifndef TYPE_COMM /* */ # define TYPE_COMM 0x09 /* Communications device */ #endif /************************************************************************/ /* */ /* Inquiry flag definitions (Inq data byte 7) */ /* */ /************************************************************************/ #define SCSI_INQ_RELADR 0x80 /* device supports relative addressing */ #define SCSI_INQ_WBUS32 0x40 /* device supports 32 bit data xfers */ #define SCSI_INQ_WBUS16 0x20 /* device supports 16 bit data xfers */ #define SCSI_INQ_SYNC 0x10 /* device supports synchronous xfer */ #define SCSI_INQ_LINKED 0x08 /* device supports linked commands */ #define SCSI_INQ_CMDQUEUE 0x02 /* device supports command queueing */ #define SCSI_INQ_SFTRE 0x01 /* device supports soft resets */ #define ENABLE_CE 1 #define DISABLE_CE 0 #define EEPROM_READ 0x80 /************************************************************************/ /* */ /* The PCI configuration register offset for TRM_S1040 */ /* */ /************************************************************************/ #define TRM_S1040_ID 0x00 /* Vendor and Device ID */ #define TRM_S1040_COMMAND 0x04 /* PCI command register */ #define TRM_S1040_IOBASE 0x10 /* I/O Space base address */ #define TRM_S1040_ROMBASE 0x30 /* Expansion ROM Base Address */ #define TRM_S1040_INTLINE 0x3C /* Interrupt line */ /************************************************************************/ /* */ /* The SCSI register offset for TRM_S1040 */ /* */ /************************************************************************/ #define TRM_S1040_SCSI_STATUS 0x80 /* SCSI Status (R) */ #define COMMANDPHASEDONE 0x2000 /* SCSI command phase done */ #define SCSIXFERDONE 0x0800 /* SCSI SCSI transfer done */ #define SCSIXFERCNT_2_ZERO 0x0100 /* SCSI SCSI transfer count to zero */ #define SCSIINTERRUPT 0x0080 /* SCSI interrupt pending */ #define COMMANDABORT 0x0040 /* SCSI command abort */ #define SEQUENCERACTIVE 0x0020 /* SCSI sequencer active */ #define PHASEMISMATCH 0x0010 /* SCSI phase mismatch */ #define PARITYERROR 0x0008 /* SCSI parity error */ #define PHASEMASK 0x0007 /* Phase MSG/CD/IO */ #define PH_DATA_OUT 0x00 /* Data out phase */ #define PH_DATA_IN 0x01 /* Data in phase */ #define PH_COMMAND 0x02 /* Command phase */ #define PH_STATUS 0x03 /* Status phase */ #define PH_BUS_FREE 0x05 /* Invalid phase used as bus free */ #define PH_MSG_OUT 0x06 /* Message out phase */ #define PH_MSG_IN 0x07 /* Message in phase */ #define TRM_S1040_SCSI_CONTROL 0x80 /* SCSI Control (W) */ #define DO_CLRATN 0x0400 /* Clear ATN */ #define DO_SETATN 0x0200 /* Set ATN */ #define DO_CMDABORT 0x0100 /* Abort SCSI command */ #define DO_RSTMODULE 0x0010 /* Reset SCSI chip */ #define DO_RSTSCSI 0x0008 /* Reset SCSI bus */ #define DO_CLRFIFO 0x0004 /* Clear SCSI transfer FIFO */ #define DO_DATALATCH 0x0002 /* Enable SCSI bus data input (latched) */ /* #define DO_DATALATCH 0x0000 */ /* KG: DISable SCSI bus data latch */ #define DO_HWRESELECT 0x0001 /* Enable hardware reselection */ #define TRM_S1040_SCSI_FIFOCNT 0x82 /* SCSI FIFO Counter 5bits(R) */ #define TRM_S1040_SCSI_SIGNAL 0x83 /* SCSI low level signal (R/W) */ #define TRM_S1040_SCSI_INTSTATUS 0x84 /* SCSI Interrupt Status (R) */ #define INT_SCAM 0x80 /* SCAM selection interrupt */ #define INT_SELECT 0x40 /* Selection interrupt */ #define INT_SELTIMEOUT 0x20 /* Selection timeout interrupt */ #define INT_DISCONNECT 0x10 /* Bus disconnected interrupt */ #define INT_RESELECTED 0x08 /* Reselected interrupt */ #define INT_SCSIRESET 0x04 /* SCSI reset detected interrupt */ #define INT_BUSSERVICE 0x02 /* Bus service interrupt */ #define INT_CMDDONE 0x01 /* SCSI command done interrupt */ #define TRM_S1040_SCSI_OFFSET 0x84 /* SCSI Offset Count (W) */ /************************************************************************/ /* */ /* Bit Name Definition */ /* --------- ------------- ---------------------------- */ /* 07-05 0 RSVD Reversed. Always 0. */ /* 04 0 OFFSET4 Reversed for LVDS. Always 0. */ /* 03-00 0 OFFSET[03:00] Offset number from 0 to 15 */ /* */ /************************************************************************/ #define TRM_S1040_SCSI_SYNC 0x85 /* SCSI Synchronous Control (R/W) */ #define LVDS_SYNC 0x20 /* Enable LVDS synchronous */ #define WIDE_SYNC 0x10 /* Enable WIDE synchronous */ #define ALT_SYNC 0x08 /* Enable Fast-20 alternate synchronous */ /************************************************************************/ /* */ /* SYNCM 7 6 5 4 3 2 1 0 */ /* Name RSVD RSVD LVDS WIDE ALTPERD PERIOD2 PERIOD1 PERIOD0 */ /* Default 0 0 0 0 0 0 0 0 */ /* */ /* Bit Name Definition */ /* --------- ------------- --------------------------- */ /* 07-06 0 RSVD Reversed. Always read 0 */ /* 05 0 LVDS Reversed. Always read 0 */ /* 04 0 WIDE/WSCSI Enable wide (16-bits) SCSI */ /* transfer. */ /* 03 0 ALTPERD/ALTPD Alternate (Sync./Period) mode. */ /* */ /* @@ When this bit is set, */ /* the synchronous period bits 2:0 */ /* in the Synchronous Mode register */ /* are used to transfer data */ /* at the Fast-20 rate. */ /* @@ When this bit is unset, */ /* the synchronous period bits 2:0 */ /* in the Synchronous Mode Register */ /* are used to transfer data */ /* at the Fast-10 rate (or Fast-40 w/ LVDS). */ /* */ /* 02-00 0 PERIOD[2:0]/ Synchronous SCSI Transfer Rate. */ /* SXPD[02:00] These 3 bits specify */ /* the Synchronous SCSI Transfer */ /* Rate for Fast-20 and Fast-10. */ /* These bits are also reset */ /* by a SCSI Bus reset. */ /* */ /* For Fast-10 bit ALTPD = 0 and LVDS = 0 */ /* and bit2,bit1,bit0 is defined as follows : */ /* */ /* 000 100ns, 10.0 MHz */ /* 001 150ns, 6.6 MHz */ /* 010 200ns, 5.0 MHz */ /* 011 250ns, 4.0 MHz */ /* 100 300ns, 3.3 MHz */ /* 101 350ns, 2.8 MHz */ /* 110 400ns, 2.5 MHz */ /* 111 450ns, 2.2 MHz */ /* */ /* For Fast-20 bit ALTPD = 1 and LVDS = 0 */ /* and bit2,bit1,bit0 is defined as follows : */ /* */ /* 000 50ns, 20.0 MHz */ /* 001 75ns, 13.3 MHz */ /* 010 100ns, 10.0 MHz */ /* 011 125ns, 8.0 MHz */ /* 100 150ns, 6.6 MHz */ /* 101 175ns, 5.7 MHz */ /* 110 200ns, 5.0 MHz */ /* 111 250ns, 4.0 MHz KG: Maybe 225ns, 4.4 MHz */ /* */ /* For Fast-40 bit ALTPD = 0 and LVDS = 1 */ /* and bit2,bit1,bit0 is defined as follows : */ /* */ /* 000 25ns, 40.0 MHz */ /* 001 50ns, 20.0 MHz */ /* 010 75ns, 13.3 MHz */ /* 011 100ns, 10.0 MHz */ /* 100 125ns, 8.0 MHz */ /* 101 150ns, 6.6 MHz */ /* 110 175ns, 5.7 MHz */ /* 111 200ns, 5.0 MHz */ /* */ /************************************************************************/ #define TRM_S1040_SCSI_TARGETID 0x86 /* SCSI Target ID (R/W) */ #define TRM_S1040_SCSI_IDMSG 0x87 /* SCSI Identify Message (R) */ #define TRM_S1040_SCSI_HOSTID 0x87 /* SCSI Host ID (W) */ #define TRM_S1040_SCSI_COUNTER 0x88 /* SCSI Transfer Counter 24bits(R/W) */ #define TRM_S1040_SCSI_INTEN 0x8C /* SCSI Interrupt Enable (R/W) */ #define EN_SCAM 0x80 /* Enable SCAM selection interrupt */ #define EN_SELECT 0x40 /* Enable selection interrupt */ #define EN_SELTIMEOUT 0x20 /* Enable selection timeout interrupt */ #define EN_DISCONNECT 0x10 /* Enable bus disconnected interrupt */ #define EN_RESELECTED 0x08 /* Enable reselected interrupt */ #define EN_SCSIRESET 0x04 /* Enable SCSI reset detected interrupt */ #define EN_BUSSERVICE 0x02 /* Enable bus service interrupt */ #define EN_CMDDONE 0x01 /* Enable SCSI command done interrupt */ #define TRM_S1040_SCSI_CONFIG0 0x8D /* SCSI Configuration 0 (R/W) */ #define PHASELATCH 0x40 /* Enable phase latch */ #define INITIATOR 0x20 /* Enable initiator mode */ #define PARITYCHECK 0x10 /* Enable parity check */ #define BLOCKRST 0x01 /* Disable SCSI reset1 */ #define TRM_S1040_SCSI_CONFIG1 0x8E /* SCSI Configuration 1 (R/W) */ #define ACTIVE_NEGPLUS 0x10 /* Enhance active negation */ #define FILTER_DISABLE 0x08 /* Disable SCSI data filter */ #define FAST_FILTER 0x04 /* ? */ #define ACTIVE_NEG 0x02 /* Enable active negation */ #define TRM_S1040_SCSI_CONFIG2 0x8F /* SCSI Configuration 2 (R/W) */ #define CFG2_WIDEFIFO 0x02 /* */ #define TRM_S1040_SCSI_COMMAND 0x90 /* SCSI Command (R/W) */ #define SCMD_COMP 0x12 /* Command complete */ #define SCMD_SEL_ATN 0x60 /* Selection with ATN */ #define SCMD_SEL_ATN3 0x64 /* Selection with ATN3 */ #define SCMD_SEL_ATNSTOP 0xB8 /* Selection with ATN and Stop */ #define SCMD_FIFO_OUT 0xC0 /* SCSI FIFO transfer out */ #define SCMD_DMA_OUT 0xC1 /* SCSI DMA transfer out */ #define SCMD_FIFO_IN 0xC2 /* SCSI FIFO transfer in */ #define SCMD_DMA_IN 0xC3 /* SCSI DMA transfer in */ #define SCMD_MSGACCEPT 0xD8 /* Message accept */ /************************************************************************/ /* */ /* Code Command Description */ /* ---- ---------------------------------------- */ /* 02 Enable reselection with FIFO */ /* 40 Select without ATN with FIFO */ /* 60 Select with ATN with FIFO */ /* 64 Select with ATN3 with FIFO */ /* A0 Select with ATN and stop with FIFO */ /* C0 Transfer information out with FIFO */ /* C1 Transfer information out with DMA */ /* C2 Transfer information in with FIFO */ /* C3 Transfer information in with DMA */ /* 12 Initiator command complete with FIFO */ /* 50 Initiator transfer information out sequence without ATN */ /* with FIFO */ /* 70 Initiator transfer information out sequence with ATN */ /* with FIFO */ /* 74 Initiator transfer information out sequence with ATN3 */ /* with FIFO */ /* 52 Initiator transfer information in sequence without ATN */ /* with FIFO */ /* 72 Initiator transfer information in sequence with ATN */ /* with FIFO */ /* 76 Initiator transfer information in sequence with ATN3 */ /* with FIFO */ /* 90 Initiator transfer information out command complete */ /* with FIFO */ /* 92 Initiator transfer information in command complete */ /* with FIFO */ /* D2 Enable selection */ /* 08 Reselection */ /* 48 Disconnect command with FIFO */ /* 88 Terminate command with FIFO */ /* C8 Target command complete with FIFO */ /* 18 SCAM Arbitration/ Selection */ /* 5A Enable reselection */ /* 98 Select without ATN with FIFO */ /* B8 Select with ATN with FIFO */ /* D8 Message Accepted */ /* 58 NOP */ /* */ /************************************************************************/ #define TRM_S1040_SCSI_TIMEOUT 0x91 /* SCSI Time Out Value (R/W) */ #define TRM_S1040_SCSI_FIFO 0x98 /* SCSI FIFO (R/W) */ #define TRM_S1040_SCSI_TCR0 0x9C /* SCSI Target Control 0 (R/W) */ #define TCR0_WIDE_NEGO_DONE 0x8000 /* Wide nego done */ #define TCR0_SYNC_NEGO_DONE 0x4000 /* Synchronous nego done */ #define TCR0_ENABLE_LVDS 0x2000 /* Enable LVDS synchronous */ #define TCR0_ENABLE_WIDE 0x1000 /* Enable WIDE synchronous */ #define TCR0_ENABLE_ALT 0x0800 /* Enable alternate synchronous */ #define TCR0_PERIOD_MASK 0x0700 /* Transfer rate */ #define TCR0_DO_WIDE_NEGO 0x0080 /* Do wide NEGO */ #define TCR0_DO_SYNC_NEGO 0x0040 /* Do sync NEGO */ #define TCR0_DISCONNECT_EN 0x0020 /* Disconnection enable */ #define TCR0_OFFSET_MASK 0x001F /* Offset number */ #define TRM_S1040_SCSI_TCR1 0x9E /* SCSI Target Control 1 (R/W) */ #define MAXTAG_MASK 0x7F00 /* Maximum tags (127) */ #define NON_TAG_BUSY 0x0080 /* Non tag command active */ #define ACTTAG_MASK 0x007F /* Active tags */ /************************************************************************/ /* */ /* The DMA register offset for TRM_S1040 */ /* */ /************************************************************************/ #define TRM_S1040_DMA_COMMAND 0xA0 /* DMA Command (R/W) */ #define DMACMD_SG 0x02 /* Enable HW S/G support */ #define DMACMD_DIR 0x01 /* 1 = read from SCSI write to Host */ #define XFERDATAIN_SG 0x0103 /* Transfer data in w/ SG */ #define XFERDATAOUT_SG 0x0102 /* Transfer data out w/ SG */ #define XFERDATAIN 0x0101 /* Transfer data in w/o SG */ #define XFERDATAOUT 0x0100 /* Transfer data out w/o SG */ #define TRM_S1040_DMA_FIFOCNT 0xA1 /* DMA FIFO Counter (R) */ #define TRM_S1040_DMA_CONTROL 0xA1 /* DMA Control (W) */ #define DMARESETMODULE 0x10 /* Reset PCI/DMA module */ #define STOPDMAXFER 0x08 /* Stop DMA transfer */ #define ABORTXFER 0x04 /* Abort DMA transfer */ #define CLRXFIFO 0x02 /* Clear DMA transfer FIFO */ #define STARTDMAXFER 0x01 /* Start DMA transfer */ #define TRM_S1040_DMA_FIFOSTAT 0xA2 /* DMA FIFO Status (R) */ #define TRM_S1040_DMA_STATUS 0xA3 /* DMA Interrupt Status (R/W) */ #define XFERPENDING 0x80 /* Transfer pending */ #define SCSIBUSY 0x40 /* SCSI busy */ #define GLOBALINT 0x20 /* DMA_INTEN bit 0-4 set */ #define FORCEDMACOMP 0x10 /* Force DMA transfer complete */ #define DMAXFERERROR 0x08 /* DMA transfer error */ #define DMAXFERABORT 0x04 /* DMA transfer abort */ #define DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */ #define SCSICOMP 0x01 /* SCSI complete interrupt */ #define TRM_S1040_DMA_INTEN 0xA4 /* DMA Interrupt Enable (R/W) */ #define EN_FORCEDMACOMP 0x10 /* Force DMA transfer complete */ #define EN_DMAXFERERROR 0x08 /* DMA transfer error */ #define EN_DMAXFERABORT 0x04 /* DMA transfer abort */ #define EN_DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */ #define EN_SCSIINTR 0x01 /* Enable SCSI complete interrupt */ #define TRM_S1040_DMA_CONFIG 0xA6 /* DMA Configuration (R/W) */ #define DMA_ENHANCE 0x8000 /* Enable DMA enhance feature (SG?) */ #define DMA_PCI_DUAL_ADDR 0x4000 /* */ #define DMA_CFG_RES 0x2000 /* Always 1 */ #define DMA_AUTO_CLR_FIFO 0x1000 /* DISable DMA auto clear FIFO */ #define DMA_MEM_MULTI_READ 0x0800 /* */ #define DMA_MEM_WRITE_INVAL 0x0400 /* Memory write and invalidate */ #define DMA_FIFO_CTRL 0x0300 /* Control FIFO operation with DMA */ #define DMA_FIFO_HALF_HALF 0x0200 /* Keep half filled on both read/write */ #define TRM_S1040_DMA_XCNT 0xA8 /* DMA Transfer Counter (R/W), 24bits */ #define TRM_S1040_DMA_CXCNT 0xAC /* DMA Current Transfer Counter (R) */ #define TRM_S1040_DMA_XLOWADDR 0xB0 /* DMA Transfer Physical Low Address */ #define TRM_S1040_DMA_XHIGHADDR 0xB4 /* DMA Transfer Physical High Address */ /************************************************************************/ /* */ /* The general register offset for TRM_S1040 */ /* */ /************************************************************************/ #define TRM_S1040_GEN_CONTROL 0xD4 /* Global Control */ #define CTRL_LED 0x80 /* Control onboard LED */ #define EN_EEPROM 0x10 /* Enable EEPROM programming */ #define DIS_TERM 0x08 /* Disable onboard termination */ #define AUTOTERM 0x04 /* Enable Auto SCSI terminator */ #define LOW8TERM 0x02 /* Enable Lower 8 bit SCSI terminator */ #define UP8TERM 0x01 /* Enable Upper 8 bit SCSI terminator */ #define TRM_S1040_GEN_STATUS 0xD5 /* Global Status */ #define GTIMEOUT 0x80 /* Global timer reach 0 */ #define EXT68HIGH 0x40 /* Higher 8 bit connected externally */ #define INT68HIGH 0x20 /* Higher 8 bit connected internally */ #define CON5068 0x10 /* External 50/68 pin connected (low) */ #define CON68 0x08 /* Internal 68 pin connected (low) */ #define CON50 0x04 /* Internal 50 pin connected (low!) */ #define WIDESCSI 0x02 /* Wide SCSI card */ #define STATUS_LOAD_DEFAULT 0x01 /* */ #define TRM_S1040_GEN_NVRAM 0xD6 /* Serial NON-VOLATILE RAM port */ #define NVR_BITOUT 0x08 /* Serial data out */ #define NVR_BITIN 0x04 /* Serial data in */ #define NVR_CLOCK 0x02 /* Serial clock */ #define NVR_SELECT 0x01 /* Serial select */ #define TRM_S1040_GEN_EDATA 0xD7 /* Parallel EEPROM data port */ #define TRM_S1040_GEN_EADDRESS 0xD8 /* Parallel EEPROM address */ #define TRM_S1040_GEN_TIMER 0xDB /* Global timer */ /************************************************************************/ /* */ /* NvmTarCfg0: Target configuration byte 0 :..pDCB->DevMode */ /* */ /************************************************************************/ #define NTC_DO_WIDE_NEGO 0x20 /* Wide negotiate */ #define NTC_DO_TAG_QUEUEING 0x10 /* Enable SCSI tag queuing */ #define NTC_DO_SEND_START 0x08 /* Send start command SPINUP */ #define NTC_DO_DISCONNECT 0x04 /* Enable SCSI disconnect */ #define NTC_DO_SYNC_NEGO 0x02 /* Sync negotiation */ #define NTC_DO_PARITY_CHK 0x01 /* (it sould define at NAC) */ /* Parity check enable */ /************************************************************************/ /* */ /* Nvram Initiater bits definition */ /* */ /************************************************************************/ #if 0 #define MORE2_DRV BIT0 #define GREATER_1G BIT1 #define RST_SCSI_BUS BIT2 #define ACTIVE_NEGATION BIT3 #define NO_SEEK BIT4 #define LUN_CHECK BIT5 #endif /************************************************************************/ /* */ /* Nvram Adapter Cfg bits definition */ /* */ /************************************************************************/ #define NAC_SCANLUN 0x20 /* Include LUN as BIOS device */ #define NAC_POWERON_SCSI_RESET 0x04 /* Power on reset enable */ #define NAC_GREATER_1G 0x02 /* > 1G support enable */ #define NAC_GT2DRIVES 0x01 /* Support more than 2 drives */ /* #define NAC_DO_PARITY_CHK 0x08 */ /* Parity check enable */ #endif