/* linux/drivers/mfd/sm501.c * * Copyright (C) 2006 Simtec Electronics * Ben Dooks * Vincent Sanders * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * * SM501 MFD driver */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include struct sm501_device { struct list_head list; struct platform_device pdev; }; struct sm501_gpio; #ifdef CONFIG_MFD_SM501_GPIO #include struct sm501_gpio_chip { struct gpio_chip gpio; struct sm501_gpio *ourgpio; /* to get back to parent. */ void __iomem *regbase; void __iomem *control; /* address of control reg. */ }; struct sm501_gpio { struct sm501_gpio_chip low; struct sm501_gpio_chip high; spinlock_t lock; unsigned int registered : 1; void __iomem *regs; struct resource *regs_res; }; #else struct sm501_gpio { /* no gpio support, empty definition for sm501_devdata. */ }; #endif struct sm501_devdata { spinlock_t reg_lock; struct mutex clock_lock; struct list_head devices; struct sm501_gpio gpio; struct device *dev; struct resource *io_res; struct resource *mem_res; struct resource *regs_claim; struct sm501_platdata *platdata; unsigned int in_suspend; unsigned long pm_misc; int unit_power[20]; unsigned int pdev_id; unsigned int irq; void __iomem *regs; unsigned int rev; }; #define MHZ (1000 * 1000) #ifdef DEBUG static const unsigned int div_tab[] = { [0] = 1, [1] = 2, [2] = 4, [3] = 8, [4] = 16, [5] = 32, [6] = 64, [7] = 128, [8] = 3, [9] = 6, [10] = 12, [11] = 24, [12] = 48, [13] = 96, [14] = 192, [15] = 384, [16] = 5, [17] = 10, [18] = 20, [19] = 40, [20] = 80, [21] = 160, [22] = 320, [23] = 604, }; static unsigned long decode_div(unsigned long pll2, unsigned long val, unsigned int lshft, unsigned int selbit, unsigned long mask) { if (val & selbit) pll2 = 288 * MHZ; return pll2 / div_tab[(val >> lshft) & mask]; } #define fmt_freq(x) ((x) / MHZ), ((x) % MHZ), (x) /* sm501_dump_clk * * Print out the current clock configuration for the device */ static void sm501_dump_clk(struct sm501_devdata *sm) { unsigned long misct = readl(sm->regs + SM501_MISC_TIMING); unsigned long pm0 = readl(sm->regs + SM501_POWER_MODE_0_CLOCK); unsigned long pm1 = readl(sm->regs + SM501_POWER_MODE_1_CLOCK); unsigned long pmc = readl(sm->regs + SM501_POWER_MODE_CONTROL); unsigned long sdclk0, sdclk1; unsigned long pll2 = 0; switch (misct & 0x30) { case 0x00: pll2 = 336 * MHZ; break; case 0x10: pll2 = 288 * MHZ; break; case 0x20: pll2 = 240 * MHZ; break; case 0x30: pll2 = 192 * MHZ; break; } sdclk0 = (misct & (1<<12)) ? pll2 : 288 * MHZ; sdclk0 /= div_tab[((misct >> 8) & 0xf)]; sdclk1 = (misct & (1<<20)) ? pll2 : 288 * MHZ; sdclk1 /= div_tab[((misct >> 16) & 0xf)]; dev_dbg(sm->dev, "MISCT=%08lx, PM0=%08lx, PM1=%08lx\n", misct, pm0, pm1); dev_dbg(sm->dev, "PLL2 = %ld.%ld MHz (%ld), SDCLK0=%08lx, SDCLK1=%08lx\n", fmt_freq(pll2), sdclk0, sdclk1); dev_dbg(sm->dev, "SDRAM: PM0=%ld, PM1=%ld\n", sdclk0, sdclk1); dev_dbg(sm->dev, "PM0[%c]: " "P2 %ld.%ld MHz (%ld), V2 %ld.%ld (%ld), " "M %ld.%ld (%ld), MX1 %ld.%ld (%ld)\n", (pmc & 3 ) == 0 ? '*' : '-', fmt_freq(decode_div(pll2, pm0, 24, 1<<29, 31)), fmt_freq(decode_div(pll2, pm0, 16, 1<<20, 15)), fmt_freq(decode_div(pll2, pm0, 8, 1<<12, 15)), fmt_freq(decode_div(pll2, pm0, 0, 1<<4, 15))); dev_dbg(sm->dev, "PM1[%c]: " "P2 %ld.%ld MHz (%ld), V2 %ld.%ld (%ld), " "M %ld.%ld (%ld), MX1 %ld.%ld (%ld)\n", (pmc & 3 ) == 1 ? '*' : '-', fmt_freq(decode_div(pll2, pm1, 24, 1<<29, 31)), fmt_freq(decode_div(pll2, pm1, 16, 1<<20, 15)), fmt_freq(decode_div(pll2, pm1, 8, 1<<12, 15)), fmt_freq(decode_div(pll2, pm1, 0, 1<<4, 15))); } static void sm501_dump_regs(struct sm501_devdata *sm) { void __iomem *regs = sm->regs; dev_info(sm->dev, "System Control %08x\n", readl(regs + SM501_SYSTEM_CONTROL)); dev_info(sm->dev, "Misc Control %08x\n", readl(regs + SM501_MISC_CONTROL)); dev_info(sm->dev, "GPIO Control Low %08x\n", readl(regs + SM501_GPIO31_0_CONTROL)); dev_info(sm->dev, "GPIO Control Hi %08x\n", readl(regs + SM501_GPIO63_32_CONTROL)); dev_info(sm->dev, "DRAM Control %08x\n", readl(regs + SM501_DRAM_CONTROL)); dev_info(sm->dev, "Arbitration Ctrl %08x\n", readl(regs + SM501_ARBTRTN_CONTROL)); dev_info(sm->dev, "Misc Timing %08x\n", readl(regs + SM501_MISC_TIMING)); } static void sm501_dump_gate(struct sm501_devdata *sm) { dev_info(sm->dev, "CurrentGate %08x\n", readl(sm->regs + SM501_CURRENT_GATE)); dev_info(sm->dev, "CurrentClock %08x\n", readl(sm->regs + SM501_CURRENT_CLOCK)); dev_info(sm->dev, "PowerModeControl %08x\n", readl(sm->regs + SM501_POWER_MODE_CONTROL)); } #else static inline void sm501_dump_gate(struct sm501_devdata *sm) { } static inline void sm501_dump_regs(struct sm501_devdata *sm) { } static inline void sm501_dump_clk(struct sm501_devdata *sm) { } #endif /* sm501_sync_regs * * ensure the */ static void sm501_sync_regs(struct sm501_devdata *sm) { readl(sm->regs); } static inline void sm501_mdelay(struct sm501_devdata *sm, unsigned int delay) { /* during suspend/resume, we are currently not allowed to sleep, * so change to using mdelay() instead of msleep() if we * are in one of these paths */ if (sm->in_suspend) mdelay(delay); else msleep(delay); } /* sm501_misc_control * * alters the miscellaneous control parameters */ int sm501_misc_control(struct device *dev, unsigned long set, unsigned long clear) { struct sm501_devdata *sm = dev_get_drvdata(dev); unsigned long misc; unsigned long save; unsigned long to; spin_lock_irqsave(&sm->reg_lock, save); misc = readl(sm->regs + SM501_MISC_CONTROL); to = (misc & ~clear) | set; if (to != misc) { writel(to, sm->regs + SM501_MISC_CONTROL); sm501_sync_regs(sm); dev_dbg(sm->dev, "MISC_CONTROL %08lx\n", misc); } spin_unlock_irqrestore(&sm->reg_lock, save); return to; } EXPORT_SYMBOL_GPL(sm501_misc_control); /* sm501_modify_reg * * Modify a register in the SM501 which may be shared with other * drivers. */ unsigned long sm501_modify_reg(struct device *dev, unsigned long reg, unsigned long set, unsigned long clear) { struct sm501_devdata *sm = dev_get_drvdata(dev); unsigned long data; unsigned long save; spin_lock_irqsave(&sm->reg_lock, save); data = readl(sm->regs + reg); data |= set; data &= ~clear; writel(data, sm->regs + reg); sm501_sync_regs(sm); spin_unlock_irqrestore(&sm->reg_lock, save); return data; } EXPORT_SYMBOL_GPL(sm501_modify_reg); /* sm501_unit_power * * alters the power active gate to set specific units on or off */ int sm501_unit_power(struct device *dev, unsigned int unit, unsigned int to) { struct sm501_devdata *sm = dev_get_drvdata(dev); unsigned long mode; unsigned long gate; unsigned long clock; mutex_lock(&sm->clock_lock); mode = readl(sm->regs + SM501_POWER_MODE_CONTROL); gate = readl(sm->regs + SM501_CURRENT_GATE); clock = readl(sm->regs + SM501_CURRENT_CLOCK); mode &= 3; /* get current power mode */ if (unit >= ARRAY_SIZE(sm->unit_power)) { dev_err(dev, "%s: bad unit %d\n", __func__, unit); goto already; } dev_dbg(sm->dev, "%s: unit %d, cur %d, to %d\n", __func__, unit, sm->unit_power[unit], to); if (to == 0 && sm->unit_power[unit] == 0) { dev_err(sm->dev, "unit %d is already shutdown\n", unit); goto already; } sm->unit_power[unit] += to ? 1 : -1; to = sm->unit_power[unit] ? 1 : 0; if (to) { if (gate & (1 << unit)) goto already; gate |= (1 << unit); } else { if (!(gate & (1 << unit))) goto already; gate &= ~(1 << unit); } switch (mode) { case 1: writel(gate, sm->regs + SM501_POWER_MODE_0_GATE); writel(clock, sm->regs + SM501_POWER_MODE_0_CLOCK); mode = 0; break; case 2: case 0: writel(gate, sm->regs + SM501_POWER_MODE_1_GATE); writel(clock, sm->regs + SM501_POWER_MODE_1_CLOCK); mode = 1; break; default: gate = -1; goto already; } writel(mode, sm->regs + SM501_POWER_MODE_CONTROL); sm501_sync_regs(sm); dev_dbg(sm->dev, "gate %08lx, clock %08lx, mode %08lx\n", gate, clock, mode); sm501_mdelay(sm, 16); already: mutex_unlock(&sm->clock_lock); return gate; } EXPORT_SYMBOL_GPL(sm501_unit_power); /* Perform a rounded division. */ static long sm501fb_round_div(long num, long denom) { /* n / d + 1 / 2 = (2n + d) / 2d */ return (2 * num + denom) / (2 * denom); } /* clock value structure. */ struct sm501_clock { unsigned long mclk; int divider; int shift; unsigned int m, n, k; }; /* sm501_calc_clock * * Calculates the nearest discrete clock frequency that * can be achieved with the specified input clock. * the maximum divisor is 3 or 5 */ static int sm501_calc_clock(unsigned long freq, struct sm501_clock *clock, int max_div, unsigned long mclk, long *best_diff) { int ret = 0; int divider; int shift; long diff; /* try dividers 1 and 3 for CRT and for panel, try divider 5 for panel only.*/ for (divider = 1; divider <= max_div; divider += 2) { /* try all 8 shift values.*/ for (shift = 0; shift < 8; shift++) { /* Calculate difference to requested clock */ diff = sm501fb_round_div(mclk, divider << shift) - freq; if (diff < 0) diff = -diff; /* If it is less than the current, use it */ if (diff < *best_diff) { *best_diff = diff; clock->mclk = mclk; clock->divider = divider; clock->shift = shift; ret = 1; } } } return ret; } /* sm501_calc_pll * * Calculates the nearest discrete clock frequency that can be * achieved using the programmable PLL. * the maximum divisor is 3 or 5 */ static unsigned long sm501_calc_pll(unsigned long freq, struct sm501_clock *clock, int max_div) { unsigned long mclk; unsigned int m, n, k; long best_diff = 999999999; /* * The SM502 datasheet doesn't specify the min/max values for M and N. * N = 1 at least doesn't work in practice. */ for (m = 2; m <= 255; m++) { for (n = 2; n <= 127; n++) { for (k = 0; k <= 1; k++) { mclk = (24000000UL * m / n) >> k; if (sm501_calc_clock(freq, clock, max_div, mclk, &best_diff)) { clock->m = m; clock->n = n; clock->k = k; } } } } /* Return best clock. */ return clock->mclk / (clock->divider << clock->shift); } /* sm501_select_clock * * Calculates the nearest discrete clock frequency that can be * achieved using the 288MHz and 336MHz PLLs. * the maximum divisor is 3 or 5 */ static unsigned long sm501_select_clock(unsigned long freq, struct sm501_clock *clock, int max_div) { unsigned long mclk; long best_diff = 999999999; /* Try 288MHz and 336MHz clocks. */ for (mclk = 288000000; mclk <= 336000000; mclk += 48000000) { sm501_calc_clock(freq, clock, max_div, mclk, &best_diff); } /* Return best clock. */ return clock->mclk / (clock->divider << clock->shift); } /* sm501_set_clock * * set one of the four clock sources to the closest available frequency to * the one specified */ unsigned long sm501_set_clock(struct device *dev, int clksrc, unsigned long req_freq) { struct sm501_devdata *sm = dev_get_drvdata(dev); unsigned long mode = readl(sm->regs + SM501_POWER_MODE_CONTROL); unsigned long gate = readl(sm->regs + SM501_CURRENT_GATE); unsigned long clock = readl(sm->regs + SM501_CURRENT_CLOCK); unsigned char reg; unsigned int pll_reg = 0; unsigned long sm501_freq; /* the actual frequency achieved */ struct sm501_clock to; /* find achivable discrete frequency and setup register value * accordingly, V2XCLK, MCLK and M1XCLK are the same P2XCLK * has an extra bit for the divider */ switch (clksrc) { case SM501_CLOCK_P2XCLK: /* This clock is divided in half so to achieve the * requested frequency the value must be multiplied by * 2. This clock also has an additional pre divisor */ if (sm->rev >= 0xC0) { /* SM502 -> use the programmable PLL */ sm501_freq = (sm501_calc_pll(2 * req_freq, &to, 5) / 2); reg = to.shift & 0x07;/* bottom 3 bits are shift */ if (to.divider == 3) reg |= 0x08; /* /3 divider required */ else if (to.divider == 5) reg |= 0x10; /* /5 divider required */ reg |= 0x40; /* select the programmable PLL */ pll_reg = 0x20000 | (to.k << 15) | (to.n << 8) | to.m; } else { sm501_freq = (sm501_select_clock(2 * req_freq, &to, 5) / 2); reg = to.shift & 0x07;/* bottom 3 bits are shift */ if (to.divider == 3) reg |= 0x08; /* /3 divider required */ else if (to.divider == 5) reg |= 0x10; /* /5 divider required */ if (to.mclk != 288000000) reg |= 0x20; /* which mclk pll is source */ } break; case SM501_CLOCK_V2XCLK: /* This clock is divided in half so to achieve the * requested frequency the value must be multiplied by 2. */ sm501_freq = (sm501_select_clock(2 * req_freq, &to, 3) / 2); reg=to.shift & 0x07; /* bottom 3 bits are shift */ if (to.divider == 3) reg |= 0x08; /* /3 divider required */ if (to.mclk != 288000000) reg |= 0x10; /* which mclk pll is source */ break; case SM501_CLOCK_MCLK: case SM501_CLOCK_M1XCLK: /* These clocks are the same and not further divided */ sm501_freq = sm501_select_clock( req_freq, &to, 3); reg=to.shift & 0x07; /* bottom 3 bits are shift */ if (to.divider == 3) reg |= 0x08; /* /3 divider required */ if (to.mclk != 288000000) reg |= 0x10; /* which mclk pll is source */ break; default: return 0; /* this is bad */ } mutex_lock(&sm->clock_lock); mode = readl(sm->regs + SM501_POWER_MODE_CONTROL); gate = readl(sm->regs + SM501_CURRENT_GATE); clock = readl(sm->regs + SM501_CURRENT_CLOCK); clock = clock & ~(0xFF << clksrc); clock |= reg<regs + SM501_POWER_MODE_0_GATE); writel(clock, sm->regs + SM501_POWER_MODE_0_CLOCK); mode = 0; break; case 2: case 0: writel(gate, sm->regs + SM501_POWER_MODE_1_GATE); writel(clock, sm->regs + SM501_POWER_MODE_1_CLOCK); mode = 1; break; default: mutex_unlock(&sm->clock_lock); return -1; } writel(mode, sm->regs + SM501_POWER_MODE_CONTROL); if (pll_reg) writel(pll_reg, sm->regs + SM501_PROGRAMMABLE_PLL_CONTROL); sm501_sync_regs(sm); dev_dbg(sm->dev, "gate %08lx, clock %08lx, mode %08lx\n", gate, clock, mode); sm501_mdelay(sm, 16); mutex_unlock(&sm->clock_lock); sm501_dump_clk(sm); return sm501_freq; } EXPORT_SYMBOL_GPL(sm501_set_clock); /* sm501_find_clock * * finds the closest available frequency for a given clock */ unsigned long sm501_find_clock(struct device *dev, int clksrc, unsigned long req_freq) { struct sm501_devdata *sm = dev_get_drvdata(dev); unsigned long sm501_freq; /* the frequency achieveable by the 501 */ struct sm501_clock to; switch (clksrc) { case SM501_CLOCK_P2XCLK: if (sm->rev >= 0xC0) { /* SM502 -> use the programmable PLL */ sm501_freq = (sm501_calc_pll(2 * req_freq, &to, 5) / 2); } else { sm501_freq = (sm501_select_clock(2 * req_freq, &to, 5) / 2); } break; case SM501_CLOCK_V2XCLK: sm501_freq = (sm501_select_clock(2 * req_freq, &to, 3) / 2); break; case SM501_CLOCK_MCLK: case SM501_CLOCK_M1XCLK: sm501_freq = sm501_select_clock(req_freq, &to, 3); break; default: sm501_freq = 0; /* error */ } return sm501_freq; } EXPORT_SYMBOL_GPL(sm501_find_clock); static struct sm501_device *to_sm_device(struct platform_device *pdev) { return container_of(pdev, struct sm501_device, pdev); } /* sm501_device_release * * A release function for the platform devices we create to allow us to * free any items we allocated */ static void sm501_device_release(struct device *dev) { kfree(to_sm_device(to_platform_device(dev))); } /* sm501_create_subdev * * Create a skeleton platform device with resources for passing to a * sub-driver */ static struct platform_device * sm501_create_subdev(struct sm501_devdata *sm, char *name, unsigned int res_count, unsigned int platform_data_size) { struct sm501_device *smdev; smdev = kzalloc(sizeof(struct sm501_device) + (sizeof(struct resource) * res_count) + platform_data_size, GFP_KERNEL); if (!smdev) return NULL; smdev->pdev.dev.release = sm501_device_release; smdev->pdev.name = name; smdev->pdev.id = sm->pdev_id; smdev->pdev.dev.parent = sm->dev; if (res_count) { smdev->pdev.resource = (struct resource *)(smdev+1); smdev->pdev.num_resources = res_count; } if (platform_data_size) smdev->pdev.dev.platform_data = (void *)(smdev+1); return &smdev->pdev; } /* sm501_register_device * * Register a platform device created with sm501_create_subdev() */ static int sm501_register_device(struct sm501_devdata *sm, struct platform_device *pdev) { struct sm501_device *smdev = to_sm_device(pdev); int ptr; int ret; for (ptr = 0; ptr < pdev->num_resources; ptr++) { printk(KERN_DEBUG "%s[%d] flags %08lx: %08llx..%08llx\n", pdev->name, ptr, pdev->resource[ptr].flags, (unsigned long long)pdev->resource[ptr].start, (unsigned long long)pdev->resource[ptr].end); } ret = platform_device_register(pdev); if (ret >= 0) { dev_dbg(sm->dev, "registered %s\n", pdev->name); list_add_tail(&smdev->list, &sm->devices); } else dev_err(sm->dev, "error registering %s (%d)\n", pdev->name, ret); return ret; } /* sm501_create_subio * * Fill in an IO resource for a sub device */ static void sm501_create_subio(struct sm501_devdata *sm, struct resource *res, resource_size_t offs, resource_size_t size) { res->flags = IORESOURCE_MEM; res->parent = sm->io_res; res->start = sm->io_res->start + offs; res->end = res->start + size - 1; } /* sm501_create_mem * * Fill in an MEM resource for a sub device */ static void sm501_create_mem(struct sm501_devdata *sm, struct resource *res, resource_size_t *offs, resource_size_t size) { *offs -= size; /* adjust memory size */ res->flags = IORESOURCE_MEM; res->parent = sm->mem_res; res->start = sm->mem_res->start + *offs; res->end = res->start + size - 1; } /* sm501_create_irq * * Fill in an IRQ resource for a sub device */ static void sm501_create_irq(struct sm501_devdata *sm, struct resource *res) { res->flags = IORESOURCE_IRQ; res->parent = NULL; res->start = res->end = sm->irq; } static int sm501_register_usbhost(struct sm501_devdata *sm, resource_size_t *mem_avail) { struct platform_device *pdev; pdev = sm501_create_subdev(sm, "sm501-usb", 3, 0); if (!pdev) return -ENOMEM; sm501_create_subio(sm, &pdev->resource[0], 0x40000, 0x20000); sm501_create_mem(sm, &pdev->resource[1], mem_avail, 256*1024); sm501_create_irq(sm, &pdev->resource[2]); return sm501_register_device(sm, pdev); } static void sm501_setup_uart_data(struct sm501_devdata *sm, struct plat_serial8250_port *uart_data, unsigned int offset) { uart_data->membase = sm->regs + offset; uart_data->mapbase = sm->io_res->start + offset; uart_data->iotype = UPIO_MEM; uart_data->irq = sm->irq; uart_data->flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ; uart_data->regshift = 2; uart_data->uartclk = (9600 * 16); } static int sm501_register_uart(struct sm501_devdata *sm, int devices) { struct platform_device *pdev; struct plat_serial8250_port *uart_data; pdev = sm501_create_subdev(sm, "serial8250", 0, sizeof(struct plat_serial8250_port) * 3); if (!pdev) return -ENOMEM; uart_data = pdev->dev.platform_data; if (devices & SM501_USE_UART0) { sm501_setup_uart_data(sm, uart_data++, 0x30000); sm501_unit_power(sm->dev, SM501_GATE_UART0, 1); sm501_modify_reg(sm->dev, SM501_IRQ_MASK, 1 << 12, 0); sm501_modify_reg(sm->dev, SM501_GPIO63_32_CONTROL, 0x01e0, 0); } if (devices & SM501_USE_UART1) { sm501_setup_uart_data(sm, uart_data++, 0x30020); sm501_unit_power(sm->dev, SM501_GATE_UART1, 1); sm501_modify_reg(sm->dev, SM501_IRQ_MASK, 1 << 13, 0); sm501_modify_reg(sm->dev, SM501_GPIO63_32_CONTROL, 0x1e00, 0); } pdev->id = PLAT8250_DEV_SM501; return sm501_register_device(sm, pdev); } static int sm501_register_display(struct sm501_devdata *sm, resource_size_t *mem_avail) { struct platform_device *pdev; pdev = sm501_create_subdev(sm, "sm501-fb", 4, 0); if (!pdev) return -ENOMEM; sm501_create_subio(sm, &pdev->resource[0], 0x80000, 0x10000); sm501_create_subio(sm, &pdev->resource[1], 0x100000, 0x50000); sm501_create_mem(sm, &pdev->resource[2], mem_avail, *mem_avail); sm501_create_irq(sm, &pdev->resource[3]); return sm501_register_device(sm, pdev); } #ifdef CONFIG_MFD_SM501_GPIO static inline struct sm501_gpio_chip *to_sm501_gpio(struct gpio_chip *gc) { return container_of(gc, struct sm501_gpio_chip, gpio); } static inline struct sm501_devdata *sm501_gpio_to_dev(struct sm501_gpio *gpio) { return container_of(gpio, struct sm501_devdata, gpio); } static int sm501_gpio_get(struct gpio_chip *chip, unsigned offset) { struct sm501_gpio_chip *smgpio = to_sm501_gpio(chip); unsigned long result; result = readl(smgpio->regbase + SM501_GPIO_DATA_LOW); result >>= offset; return result & 1UL; } static void sm501_gpio_ensure_gpio(struct sm501_gpio_chip *smchip, unsigned long bit) { unsigned long ctrl; /* check and modify if this pin is not set as gpio. */ if (readl(smchip->control) & bit) { dev_info(sm501_gpio_to_dev(smchip->ourgpio)->dev, "changing mode of gpio, bit %08lx\n", bit); ctrl = readl(smchip->control); ctrl &= ~bit; writel(ctrl, smchip->control); sm501_sync_regs(sm501_gpio_to_dev(smchip->ourgpio)); } } static void sm501_gpio_set(struct gpio_chip *chip, unsigned offset, int value) { struct sm501_gpio_chip *smchip = to_sm501_gpio(chip); struct sm501_gpio *smgpio = smchip->ourgpio; unsigned long bit = 1 << offset; void __iomem *regs = smchip->regbase; unsigned long save; unsigned long val; dev_dbg(sm501_gpio_to_dev(smgpio)->dev, "%s(%p,%d)\n", __func__, chip, offset); spin_lock_irqsave(&smgpio->lock, save); val = readl(regs + SM501_GPIO_DATA_LOW) & ~bit; if (value) val |= bit; writel(val, regs); sm501_sync_regs(sm501_gpio_to_dev(smgpio)); sm501_gpio_ensure_gpio(smchip, bit); spin_unlock_irqrestore(&smgpio->lock, save); } static int sm501_gpio_input(struct gpio_chip *chip, unsigned offset) { struct sm501_gpio_chip *smchip = to_sm501_gpio(chip); struct sm501_gpio *smgpio = smchip->ourgpio; void __iomem *regs = smchip->regbase; unsigned long bit = 1 << offset; unsigned long save; unsigned long ddr; dev_dbg(sm501_gpio_to_dev(smgpio)->dev, "%s(%p,%d)\n", __func__, chip, offset); spin_lock_irqsave(&smgpio->lock, save); ddr = readl(regs + SM501_GPIO_DDR_LOW); writel(ddr & ~bit, regs + SM501_GPIO_DDR_LOW); sm501_sync_regs(sm501_gpio_to_dev(smgpio)); sm501_gpio_ensure_gpio(smchip, bit); spin_unlock_irqrestore(&smgpio->lock, save); return 0; } static int sm501_gpio_output(struct gpio_chip *chip, unsigned offset, int value) { struct sm501_gpio_chip *smchip = to_sm501_gpio(chip); struct sm501_gpio *smgpio = smchip->ourgpio; unsigned long bit = 1 << offset; void __iomem *regs = smchip->regbase; unsigned long save; unsigned long val; unsigned long ddr; dev_dbg(sm501_gpio_to_dev(smgpio)->dev, "%s(%p,%d,%d)\n", __func__, chip, offset, value); spin_lock_irqsave(&smgpio->lock, save); val = readl(regs + SM501_GPIO_DATA_LOW); if (value) val |= bit; else val &= ~bit; writel(val, regs); ddr = readl(regs + SM501_GPIO_DDR_LOW); writel(ddr | bit, regs + SM501_GPIO_DDR_LOW); sm501_sync_regs(sm501_gpio_to_dev(smgpio)); writel(val, regs + SM501_GPIO_DATA_LOW); sm501_sync_regs(sm501_gpio_to_dev(smgpio)); spin_unlock_irqrestore(&smgpio->lock, save); return 0; } static struct gpio_chip gpio_chip_template = { .ngpio = 32, .direction_input = sm501_gpio_input, .direction_output = sm501_gpio_output, .set = sm501_gpio_set, .get = sm501_gpio_get, }; static int __devinit sm501_gpio_register_chip(struct sm501_devdata *sm, struct sm501_gpio *gpio, struct sm501_gpio_chip *chip) { struct sm501_platdata *pdata = sm->platdata; struct gpio_chip *gchip = &chip->gpio; int base = pdata->gpio_base; chip->gpio = gpio_chip_template; if (chip == &gpio->high) { if (base > 0) base += 32; chip->regbase = gpio->regs + SM501_GPIO_DATA_HIGH; chip->control = sm->regs + SM501_GPIO63_32_CONTROL; gchip->label = "SM501-HIGH"; } else { chip->regbase = gpio->regs + SM501_GPIO_DATA_LOW; chip->control = sm->regs + SM501_GPIO31_0_CONTROL; gchip->label = "SM501-LOW"; } gchip->base = base; chip->ourgpio = gpio; return gpiochip_add(gchip); } static int __devinit sm501_register_gpio(struct sm501_devdata *sm) { struct sm501_gpio *gpio = &sm->gpio; resource_size_t iobase = sm->io_res->start + SM501_GPIO; int ret; int tmp; dev_dbg(sm->dev, "registering gpio block %08llx\n", (unsigned long long)iobase); spin_lock_init(&gpio->lock); gpio->regs_res = request_mem_region(iobase, 0x20, "sm501-gpio"); if (gpio->regs_res == NULL) { dev_err(sm->dev, "gpio: failed to request region\n"); return -ENXIO; } gpio->regs = ioremap(iobase, 0x20); if (gpio->regs == NULL) { dev_err(sm->dev, "gpio: failed to remap registers\n"); ret = -ENXIO; goto err_claimed; } /* Register both our chips. */ ret = sm501_gpio_register_chip(sm, gpio, &gpio->low); if (ret) { dev_err(sm->dev, "failed to add low chip\n"); goto err_mapped; } ret = sm501_gpio_register_chip(sm, gpio, &gpio->high); if (ret) { dev_err(sm->dev, "failed to add high chip\n"); goto err_low_chip; } gpio->registered = 1; return 0; err_low_chip: tmp = gpiochip_remove(&gpio->low.gpio); if (tmp) { dev_err(sm->dev, "cannot remove low chip, cannot tidy up\n"); return ret; } err_mapped: iounmap(gpio->regs); err_claimed: release_resource(gpio->regs_res); kfree(gpio->regs_res); return ret; } static void sm501_gpio_remove(struct sm501_devdata *sm) { struct sm501_gpio *gpio = &sm->gpio; int ret; if (!sm->gpio.registered) return; ret = gpiochip_remove(&gpio->low.gpio); if (ret) dev_err(sm->dev, "cannot remove low chip, cannot tidy up\n"); ret = gpiochip_remove(&gpio->high.gpio); if (ret) dev_err(sm->dev, "cannot remove high chip, cannot tidy up\n"); iounmap(gpio->regs); release_resource(gpio->regs_res); kfree(gpio->regs_res); } static inline int sm501_gpio_pin2nr(struct sm501_devdata *sm, unsigned int pin) { struct sm501_gpio *gpio = &sm->gpio; int base = (pin < 32) ? gpio->low.gpio.base : gpio->high.gpio.base; return (pin % 32) + base; } static inline int sm501_gpio_isregistered(struct sm501_devdata *sm) { return sm->gpio.registered; } #else static inline int sm501_register_gpio(struct sm501_devdata *sm) { return 0; } static inline void sm501_gpio_remove(struct sm501_devdata *sm) { } static inline int sm501_gpio_pin2nr(struct sm501_devdata *sm, unsigned int pin) { return -1; } static inline int sm501_gpio_isregistered(struct sm501_devdata *sm) { return 0; } #endif static int sm501_register_gpio_i2c_instance(struct sm501_devdata *sm, struct sm501_platdata_gpio_i2c *iic) { struct i2c_gpio_platform_data *icd; struct platform_device *pdev; pdev = sm501_create_subdev(sm, "i2c-gpio", 0, sizeof(struct i2c_gpio_platform_data)); if (!pdev) return -ENOMEM; icd = pdev->dev.platform_data; /* We keep the pin_sda and pin_scl fields relative in case the * same platform data is passed to >1 SM501. */ icd->sda_pin = sm501_gpio_pin2nr(sm, iic->pin_sda); icd->scl_pin = sm501_gpio_pin2nr(sm, iic->pin_scl); icd->timeout = iic->timeout; icd->udelay = iic->udelay; /* note, we can't use either of the pin numbers, as the i2c-gpio * driver uses the platform.id field to generate the bus number * to register with the i2c core; The i2c core doesn't have enough * entries to deal with anything we currently use. */ pdev->id = iic->bus_num; dev_info(sm->dev, "registering i2c-%d: sda=%d (%d), scl=%d (%d)\n", iic->bus_num, icd->sda_pin, iic->pin_sda, icd->scl_pin, iic->pin_scl); return sm501_register_device(sm, pdev); } static int sm501_register_gpio_i2c(struct sm501_devdata *sm, struct sm501_platdata *pdata) { struct sm501_platdata_gpio_i2c *iic = pdata->gpio_i2c; int index; int ret; for (index = 0; index < pdata->gpio_i2c_nr; index++, iic++) { ret = sm501_register_gpio_i2c_instance(sm, iic); if (ret < 0) return ret; } return 0; } /* sm501_dbg_regs * * Debug attribute to attach to parent device to show core registers */ static ssize_t sm501_dbg_regs(struct device *dev, struct device_attribute *attr, char *buff) { struct sm501_devdata *sm = dev_get_drvdata(dev) ; unsigned int reg; char *ptr = buff; int ret; for (reg = 0x00; reg < 0x70; reg += 4) { ret = sprintf(ptr, "%08x = %08x\n", reg, readl(sm->regs + reg)); ptr += ret; } return ptr - buff; } static DEVICE_ATTR(dbg_regs, 0666, sm501_dbg_regs, NULL); /* sm501_init_reg * * Helper function for the init code to setup a register * * clear the bits which are set in r->mask, and then set * the bits set in r->set. */ static inline void sm501_init_reg(struct sm501_devdata *sm, unsigned long reg, struct sm501_reg_init *r) { unsigned long tmp; tmp = readl(sm->regs + reg); tmp &= ~r->mask; tmp |= r->set; writel(tmp, sm->regs + reg); } /* sm501_init_regs * * Setup core register values */ static void sm501_init_regs(struct sm501_devdata *sm, struct sm501_initdata *init) { sm501_misc_control(sm->dev, init->misc_control.set, init->misc_control.mask); sm501_init_reg(sm, SM501_MISC_TIMING, &init->misc_timing); sm501_init_reg(sm, SM501_GPIO31_0_CONTROL, &init->gpio_low); sm501_init_reg(sm, SM501_GPIO63_32_CONTROL, &init->gpio_high); if (init->m1xclk) { dev_info(sm->dev, "setting M1XCLK to %ld\n", init->m1xclk); sm501_set_clock(sm->dev, SM501_CLOCK_M1XCLK, init->m1xclk); } if (init->mclk) { dev_info(sm->dev, "setting MCLK to %ld\n", init->mclk); sm501_set_clock(sm->dev, SM501_CLOCK_MCLK, init->mclk); } } /* Check the PLL sources for the M1CLK and M1XCLK * * If the M1CLK and M1XCLKs are not sourced from the same PLL, then * there is a risk (see errata AB-5) that the SM501 will cease proper * function. If this happens, then it is likely the SM501 will * hang the system. */ static int sm501_check_clocks(struct sm501_devdata *sm) { unsigned long pwrmode = readl(sm->regs + SM501_CURRENT_CLOCK); unsigned long msrc = (pwrmode & SM501_POWERMODE_M_SRC); unsigned long m1src = (pwrmode & SM501_POWERMODE_M1_SRC); return ((msrc == 0 && m1src != 0) || (msrc != 0 && m1src == 0)); } static unsigned int sm501_mem_local[] = { [0] = 4*1024*1024, [1] = 8*1024*1024, [2] = 16*1024*1024, [3] = 32*1024*1024, [4] = 64*1024*1024, [5] = 2*1024*1024, }; /* sm501_init_dev * * Common init code for an SM501 */ static int __devinit sm501_init_dev(struct sm501_devdata *sm) { struct sm501_initdata *idata; struct sm501_platdata *pdata; resource_size_t mem_avail; unsigned long dramctrl; unsigned long devid; int ret; mutex_init(&sm->clock_lock); spin_lock_init(&sm->reg_lock); INIT_LIST_HEAD(&sm->devices); devid = readl(sm->regs + SM501_DEVICEID); if ((devid & SM501_DEVICEID_IDMASK) != SM501_DEVICEID_SM501) { dev_err(sm->dev, "incorrect device id %08lx\n", devid); return -EINVAL; } /* disable irqs */ writel(0, sm->regs + SM501_IRQ_MASK); dramctrl = readl(sm->regs + SM501_DRAM_CONTROL); mem_avail = sm501_mem_local[(dramctrl >> 13) & 0x7]; dev_info(sm->dev, "SM501 At %p: Version %08lx, %ld Mb, IRQ %d\n", sm->regs, devid, (unsigned long)mem_avail >> 20, sm->irq); sm->rev = devid & SM501_DEVICEID_REVMASK; sm501_dump_gate(sm); ret = device_create_file(sm->dev, &dev_attr_dbg_regs); if (ret) dev_err(sm->dev, "failed to create debug regs file\n"); sm501_dump_clk(sm); /* check to see if we have some device initialisation */ pdata = sm->platdata; idata = pdata ? pdata->init : NULL; if (idata) { sm501_init_regs(sm, idata); if (idata->devices & SM501_USE_USB_HOST) sm501_register_usbhost(sm, &mem_avail); if (idata->devices & (SM501_USE_UART0 | SM501_USE_UART1)) sm501_register_uart(sm, idata->devices); if (idata->devices & SM501_USE_GPIO) sm501_register_gpio(sm); } if (pdata->gpio_i2c != NULL && pdata->gpio_i2c_nr > 0) { if (!sm501_gpio_isregistered(sm)) dev_err(sm->dev, "no gpio available for i2c gpio.\n"); else sm501_register_gpio_i2c(sm, pdata); } ret = sm501_check_clocks(sm); if (ret) { dev_err(sm->dev, "M1X and M clocks sourced from different " "PLLs\n"); return -EINVAL; } /* always create a framebuffer */ sm501_register_display(sm, &mem_avail); return 0; } static int __devinit sm501_plat_probe(struct platform_device *dev) { struct sm501_devdata *sm; int ret; sm = kzalloc(sizeof(struct sm501_devdata), GFP_KERNEL); if (sm == NULL) { dev_err(&dev->dev, "no memory for device data\n"); ret = -ENOMEM; goto err1; } sm->dev = &dev->dev; sm->pdev_id = dev->id; sm->platdata = dev->dev.platform_data; ret = platform_get_irq(dev, 0); if (ret < 0) { dev_err(&dev->dev, "failed to get irq resource\n"); goto err_res; } sm->irq = ret; sm->io_res = platform_get_resource(dev, IORESOURCE_MEM, 1); sm->mem_res = platform_get_resource(dev, IORESOURCE_MEM, 0); if (sm->io_res == NULL || sm->mem_res == NULL) { dev_err(&dev->dev, "failed to get IO resource\n"); ret = -ENOENT; goto err_res; } sm->regs_claim = request_mem_region(sm->io_res->start, 0x100, "sm501"); if (sm->regs_claim == NULL) { dev_err(&dev->dev, "cannot claim registers\n"); ret = -EBUSY; goto err_res; } platform_set_drvdata(dev, sm); sm->regs = ioremap(sm->io_res->start, resource_size(sm->io_res)); if (sm->regs == NULL) { dev_err(&dev->dev, "cannot remap registers\n"); ret = -EIO; goto err_claim; } return sm501_init_dev(sm); err_claim: release_resource(sm->regs_claim); kfree(sm->regs_claim); err_res: kfree(sm); err1: return ret; } #ifdef CONFIG_PM /* power management support */ static void sm501_set_power(struct sm501_devdata *sm, int on) { struct sm501_platdata *pd = sm->platdata; if (pd == NULL) return; if (pd->get_power) { if (pd->get_power(sm->dev) == on) { dev_dbg(sm->dev, "is already %d\n", on); return; } } if (pd->set_power) { dev_dbg(sm->dev, "setting power to %d\n", on); pd->set_power(sm->dev, on); sm501_mdelay(sm, 10); } } static int sm501_plat_suspend(struct platform_device *pdev, pm_message_t state) { struct sm501_devdata *sm = platform_get_drvdata(pdev); sm->in_suspend = 1; sm->pm_misc = readl(sm->regs + SM501_MISC_CONTROL); sm501_dump_regs(sm); if (sm->platdata) { if (sm->platdata->flags & SM501_FLAG_SUSPEND_OFF) sm501_set_power(sm, 0); } return 0; } static int sm501_plat_resume(struct platform_device *pdev) { struct sm501_devdata *sm = platform_get_drvdata(pdev); sm501_set_power(sm, 1); sm501_dump_regs(sm); sm501_dump_gate(sm); sm501_dump_clk(sm); /* check to see if we are in the same state as when suspended */ if (readl(sm->regs + SM501_MISC_CONTROL) != sm->pm_misc) { dev_info(sm->dev, "SM501_MISC_CONTROL changed over sleep\n"); writel(sm->pm_misc, sm->regs + SM501_MISC_CONTROL); /* our suspend causes the controller state to change, * either by something attempting setup, power loss, * or an external reset event on power change */ if (sm->platdata && sm->platdata->init) { sm501_init_regs(sm, sm->platdata->init); } } /* dump our state from resume */ sm501_dump_regs(sm); sm501_dump_clk(sm); sm->in_suspend = 0; return 0; } #else #define sm501_plat_suspend NULL #define sm501_plat_resume NULL #endif /* Initialisation data for PCI devices */ static struct sm501_initdata sm501_pci_initdata = { .gpio_high = { .set = 0x3F000000, /* 24bit panel */ .mask = 0x0, }, .misc_timing = { .set = 0x010100, /* SDRAM timing */ .mask = 0x1F1F00, }, .misc_control = { .set = SM501_MISC_PNL_24BIT, .mask = 0, }, .devices = SM501_USE_ALL, /* Errata AB-3 says that 72MHz is the fastest available * for 33MHZ PCI with proper bus-mastering operation */ .mclk = 72 * MHZ, .m1xclk = 144 * MHZ, }; static struct sm501_platdata_fbsub sm501_pdata_fbsub = { .flags = (SM501FB_FLAG_USE_INIT_MODE | SM501FB_FLAG_USE_HWCURSOR | SM501FB_FLAG_USE_HWACCEL | SM501FB_FLAG_DISABLE_AT_EXIT), }; static struct sm501_platdata_fb sm501_fb_pdata = { .fb_route = SM501_FB_OWN, .fb_crt = &sm501_pdata_fbsub, .fb_pnl = &sm501_pdata_fbsub, }; static struct sm501_platdata sm501_pci_platdata = { .init = &sm501_pci_initdata, .fb = &sm501_fb_pdata, .gpio_base = -1, }; static int __devinit sm501_pci_probe(struct pci_dev *dev, const struct pci_device_id *id) { struct sm501_devdata *sm; int err; sm = kzalloc(sizeof(struct sm501_devdata), GFP_KERNEL); if (sm == NULL) { dev_err(&dev->dev, "no memory for device data\n"); err = -ENOMEM; goto err1; } /* set a default set of platform data */ dev->dev.platform_data = sm->platdata = &sm501_pci_platdata; /* set a hopefully unique id for our child platform devices */ sm->pdev_id = 32 + dev->devfn; pci_set_drvdata(dev, sm); err = pci_enable_device(dev); if (err) { dev_err(&dev->dev, "cannot enable device\n"); goto err2; } sm->dev = &dev->dev; sm->irq = dev->irq; #ifdef __BIG_ENDIAN /* if the system is big-endian, we most probably have a * translation in the IO layer making the PCI bus little endian * so make the framebuffer swapped pixels */ sm501_fb_pdata.flags |= SM501_FBPD_SWAP_FB_ENDIAN; #endif /* check our resources */ if (!(pci_resource_flags(dev, 0) & IORESOURCE_MEM)) { dev_err(&dev->dev, "region #0 is not memory?\n"); err = -EINVAL; goto err3; } if (!(pci_resource_flags(dev, 1) & IORESOURCE_MEM)) { dev_err(&dev->dev, "region #1 is not memory?\n"); err = -EINVAL; goto err3; } /* make our resources ready for sharing */ sm->io_res = &dev->resource[1]; sm->mem_res = &dev->resource[0]; sm->regs_claim = request_mem_region(sm->io_res->start, 0x100, "sm501"); if (sm->regs_claim == NULL) { dev_err(&dev->dev, "cannot claim registers\n"); err= -EBUSY; goto err3; } sm->regs = pci_ioremap_bar(dev, 1); if (sm->regs == NULL) { dev_err(&dev->dev, "cannot remap registers\n"); err = -EIO; goto err4; } sm501_init_dev(sm); return 0; err4: release_resource(sm->regs_claim); kfree(sm->regs_claim); err3: pci_disable_device(dev); err2: pci_set_drvdata(dev, NULL); kfree(sm); err1: return err; } static void sm501_remove_sub(struct sm501_devdata *sm, struct sm501_device *smdev) { list_del(&smdev->list); platform_device_unregister(&smdev->pdev); } static void sm501_dev_remove(struct sm501_devdata *sm) { struct sm501_device *smdev, *tmp; list_for_each_entry_safe(smdev, tmp, &sm->devices, list) sm501_remove_sub(sm, smdev); device_remove_file(sm->dev, &dev_attr_dbg_regs); sm501_gpio_remove(sm); } static void __devexit sm501_pci_remove(struct pci_dev *dev) { struct sm501_devdata *sm = pci_get_drvdata(dev); sm501_dev_remove(sm); iounmap(sm->regs); release_resource(sm->regs_claim); kfree(sm->regs_claim); pci_set_drvdata(dev, NULL); pci_disable_device(dev); } static int sm501_plat_remove(struct platform_device *dev) { struct sm501_devdata *sm = platform_get_drvdata(dev); sm501_dev_remove(sm); iounmap(sm->regs); release_resource(sm->regs_claim); kfree(sm->regs_claim); return 0; } static struct pci_device_id sm501_pci_tbl[] = { { 0x126f, 0x0501, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, { 0, }, }; MODULE_DEVICE_TABLE(pci, sm501_pci_tbl); static struct pci_driver sm501_pci_driver = { .name = "sm501", .id_table = sm501_pci_tbl, .probe = sm501_pci_probe, .remove = __devexit_p(sm501_pci_remove), }; MODULE_ALIAS("platform:sm501"); static struct platform_driver sm501_plat_driver = { .driver = { .name = "sm501", .owner = THIS_MODULE, }, .probe = sm501_plat_probe, .remove = sm501_plat_remove, .suspend = sm501_plat_suspend, .resume = sm501_plat_resume, }; static int __init sm501_base_init(void) { platform_driver_register(&sm501_plat_driver); return pci_register_driver(&sm501_pci_driver); } static void __exit sm501_base_exit(void) { platform_driver_unregister(&sm501_plat_driver); pci_unregister_driver(&sm501_pci_driver); } module_init(sm501_base_init); module_exit(sm501_base_exit); MODULE_DESCRIPTION("SM501 Core Driver"); MODULE_AUTHOR("Ben Dooks , Vincent Sanders"); MODULE_LICENSE("GPL v2");