arm/km: update mgcoge3un board support

We change default settings for egiga on mgcoge3un.
The reason we need this is that we have the gig port on mgcoge3un
connected using a back-to-back pair of PHYs. There are no magnetics and
because of that the port has to be run with a fixd configuration and
auto-negotiation must be disabled. In the default mode the egiga driver
uses autoneg to determine port speed - which defaults to 1G (we need
100M full duplex).

Add wait for the GPIO line connected to mgcoge3ne before
starting mgcoge3un. A board specific ethernet present function
was added, because on this board ethernet is always present.
The BOCO FPGA access was enhanced and changed to use register
definitions.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

2 files changed, 91 insertions, 14 deletions

diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 4049a4e86..d86acc9d0 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -41,6 +41,16 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+/*
+ * BOCO FPGA definitions
+ */
+#define BOCO		0x10
+#define REG_CTRL_H		0x02
+#define MASK_WRL_UNITRUN	0x01
+#define MASK_RBX_PGY_PRESENT	0x40
+#define REG_IRQ_CIRQ2		0x2d
+#define MASK_RBI_DEFECT_16	0x01
+
 /* Multi-Purpose Pins Functionality configuration */
 u32 kwmpp_config[] = {
 	MPP0_NF_IO2,
@@ -102,43 +112,64 @@ u32 kwmpp_config[] = {
 	0
 };
 
+#if defined(CONFIG_MGCOGE3UN)
+/*
+ * Wait for startup OK from mgcoge3ne
+ */
+int startup_allowed(void)
+{
+	unsigned char buf;
+
+	/*
+	 * Read CIRQ16 bit (bit 0)
+	 */
+	if (i2c_read(BOCO, REG_IRQ_CIRQ2, 1, &buf, 1) != 0)
+		printf("%s: Error reading Boco\n", __func__);
+	else
+		if ((buf & MASK_RBI_DEFECT_16) == MASK_RBI_DEFECT_16)
+			return 1;
+	return 0;
+}
+
+/*
+ * mgcoge3un has always ethernet present. Its connected to the 6061 switch
+ * and provides ICNev and piggy4 connections.
+ */
+int ethernet_present(void)
+{
+	return 1;
+}
+#else
 int ethernet_present(void)
 {
 	uchar	buf;
 	int	ret = 0;
 
-	if (i2c_read(0x10, 2, 1, &buf, 1) != 0) {
+	if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
 		printf("%s: Error reading Boco\n", __func__);
 		return -1;
 	}
-	if ((buf & 0x40) == 0x40)
+	if ((buf & MASK_RBX_PGY_PRESENT) == MASK_RBX_PGY_PRESENT)
 		ret = 1;
 
 	return ret;
 }
+#endif
 
 int initialize_unit_leds(void)
 {
 	/*
-	 * init the unit LEDs
-	 * per default they all are
+	 * Init the unit LEDs per default they all are
 	 * ok apart from bootstat
-	 * LED connected through BOCO
-	 * BOCO	lies at the address  0x10
-	 * LEDs are in the block CTRL_H	(addr 0x02)
-	 * BOOTSTAT LED is the first 0x01
 	 */
-	#define BOCO        0x10
-	#define CTRL_H      0x02
-	#define APPLEDMASK  0x01
 	uchar buf;
 
-	if (i2c_read(BOCO, CTRL_H, 1, &buf, 1) != 0) {
+	if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
 		printf("%s: Error reading Boco\n", __func__);
 		return -1;
 	}
-	buf |= APPLEDMASK;
-	if (i2c_write(BOCO, CTRL_H, 1, &buf, 1) != 0) {
+	buf |= MASK_WRL_UNITRUN;
+	if (i2c_write(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
 		printf("%s: Error writing Boco\n", __func__);
 		return -1;
 	}
@@ -167,6 +198,27 @@ int misc_init_r(void)
 		printf("Overwriting MACH_TYPE with %d!!!\n", mach_type);
 		gd->bd->bi_arch_number = mach_type;
 	}
+#if defined(CONFIG_MGCOGE3UN)
+	char *wait_for_ne;
+	wait_for_ne = getenv("waitforne");
+	if (wait_for_ne != NULL) {
+		if (strcmp(wait_for_ne, "true") == 0) {
+			int cnt = 0;
+			puts("NE go: ");
+			while (startup_allowed() == 0) {
+				udelay(200000);
+				cnt++;
+				if (cnt == 5)
+					puts("wait\b\b\b\b");
+				if (cnt == 10) {
+					cnt = 0;
+					puts("    \b\b\b\b");
+				}
+			}
+			puts("OK\n");
+		}
+	}
+#endif
 
 	initialize_unit_leds();
 	set_km_env();
diff --git a/include/configs/mgcoge3un.h b/include/configs/mgcoge3un.h
index 22d196168..6d56d7d08 100644
--- a/include/configs/mgcoge3un.h
+++ b/include/configs/mgcoge3un.h
@@ -50,4 +50,29 @@
 /* we use a new RAM type on mgcoge3un board */
 #define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-memphis.cfg
 
+/*
+ * mgcoge3un has a fixed link to the marvell switch
+ * with 100MB full duplex and autoneg off, for this
+ * reason we have to change the default settings
+ */
+#define PORT_SERIAL_CONTROL_VALUE		( \
+	MVGBE_FORCE_LINK_PASS			| \
+	MVGBE_DIS_AUTO_NEG_FOR_DUPLX		| \
+	MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL	| \
+	MVGBE_ADV_NO_FLOW_CTRL			| \
+	MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX	| \
+	MVGBE_FORCE_BP_MODE_NO_JAM		| \
+	(1 << 9) /* Reserved bit has to be 1 */	| \
+	MVGBE_DO_NOT_FORCE_LINK_FAIL		| \
+	MVGBE_DIS_AUTO_NEG_SPEED_GMII		| \
+	MVGBE_DTE_ADV_0				| \
+	MVGBE_MIIPHY_MAC_MODE			| \
+	MVGBE_AUTO_NEG_NO_CHANGE		| \
+	MVGBE_MAX_RX_PACKET_1552BYTE		| \
+	MVGBE_CLR_EXT_LOOPBACK			| \
+	MVGBE_SET_FULL_DUPLEX_MODE		| \
+	MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX	|\
+	MVGBE_SET_GMII_SPEED_TO_10_100	|\
+	MVGBE_SET_MII_SPEED_TO_100)
+
 #endif /* _CONFIG_MGCOGE3UN_H */