aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorJason Liu <jason.hui@linaro.org>2011-12-12 18:02:49 +0800
committerEric Miao <eric.miao@linaro.org>2012-01-02 21:54:14 +0800
commitd07f67d8cf9533a75732b0830415019721d85902 (patch)
tree379379e4da37a4e53656d359095062b435ddc4db
parent8287bddd689583c699cf9702bddae6aae235f551 (diff)
downloadu-boot-linaro-d07f67d8cf9533a75732b0830415019721d85902.tar.gz
i.mx6q: arm2: Add the enet function support
This enable the network function on the i.mx6q armadillo2 board(arm2), thus we can use tftp to load image from network. Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org>
-rw-r--r--board/freescale/mx6qarm2/mx6qarm2.c90
-rw-r--r--include/configs/mx6qarm2.h13
2 files changed, 101 insertions, 2 deletions
diff --git a/board/freescale/mx6qarm2/mx6qarm2.c b/board/freescale/mx6qarm2/mx6qarm2.c
index 89e0e76..145f38c 100644
--- a/board/freescale/mx6qarm2/mx6qarm2.c
+++ b/board/freescale/mx6qarm2/mx6qarm2.c
@@ -29,6 +29,8 @@
#include <asm/gpio.h>
#include <mmc.h>
#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -40,6 +42,10 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
@@ -79,11 +85,35 @@ iomux_v3_cfg_t usdhc4_pads[] = {
MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
+iomux_v3_cfg_t enet_pads[] = {
+ MX6Q_PAD_KEY_COL1__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_KEY_COL2__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
}
+static void setup_iomux_enet(void)
+{
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+}
+
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg usdhc_cfg[2] = {
{USDHC3_BASE_ADDR, 1},
@@ -132,9 +162,69 @@ int board_mmc_init(bd_t *bis)
}
#endif
+#define MII_MMD_ACCESS_CTRL_REG 0xd
+#define MII_MMD_ACCESS_ADDR_DATA_REG 0xe
+#define MII_DBG_PORT_REG 0x1d
+#define MII_DBG_PORT2_REG 0x1e
+
+int fecmxc_mii_postcall(int phy)
+{
+ unsigned short val;
+
+ /*
+ * Due to the i.MX6Q Armadillo2 board HW design,there is
+ * no 125Mhz clock input from SOC. In order to use RGMII,
+ * We need enable AR8031 ouput a 125MHz clk from CLK_25M
+ */
+ miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x7);
+ miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, 0x8016);
+ miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x4007);
+ miiphy_read("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, &val);
+ val &= 0xffe3;
+ val |= 0x18;
+ miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, val);
+
+ /* For the RGMII phy, we need enable tx clock delay */
+ miiphy_write("FEC", phy, 0x1d, 0x5);
+ miiphy_read("FEC", phy, 0x1e, &val);
+ val |= 0x0100;
+ miiphy_write("FEC", phy, 0x1e, val);
+
+ miiphy_write("FEC", phy, MII_BMCR, 0xa100);
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ struct eth_device *dev;
+ int ret;
+
+ ret = cpu_eth_init(bis);
+ if (ret) {
+ printf("FEC MXC: %s:failed\n", __func__);
+ return ret;
+ }
+
+ dev = eth_get_dev_by_name("FEC");
+ if (!dev) {
+ printf("FEC MXC: Unable to get FEC device entry\n");
+ return -EINVAL;
+ }
+
+ ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+ if (ret) {
+ printf("FEC MXC: Unable to register FEC mii postcall\n");
+ return ret;
+ }
+
+ return 0;
+}
+
int board_early_init_f(void)
{
setup_iomux_uart();
+ setup_iomux_enet();
return 0;
}
diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h
index a7b363d..3a30679 100644
--- a/include/configs/mx6qarm2.h
+++ b/include/configs/mx6qarm2.h
@@ -56,6 +56,17 @@
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 0
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
@@ -66,8 +77,6 @@
#include <config_cmd_default.h>
#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
#define CONFIG_BOOTDELAY 3