/* * (C) Copyright 2002,2003 Motorola,Inc. * Modified by Lunsheng Wang, lunsheng@sohu.com * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* mpc8540eval board configuration file */ /* please refer to doc/README.mpc85xxads for more info */ /* make sure you change the MAC address and other network params first, * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file */ #ifndef __CONFIG_H #define __CONFIG_H /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ #define CONFIG_MPC8540 1 /* MPC8540 specific */ #define CONFIG_MPC8540EVAL 1 /* MPC8540EVAL board specific */ #undef CONFIG_PCI /* pci ethernet support */ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ /* Using Localbus SDRAM to emulate flash before we can program the flash, * normally you only need a flash-boot image(u-boot.bin),if unsure undef this. * Not availabe for EVAL board */ #undef CONFIG_RAM_AS_FLASH /* sysclk for MPC8540EVAL */ #if defined(CONFIG_SYSCLK_66M) /* * the oscillator on board is 66Mhz * can also get 66M clock from external PCI */ #define CONFIG_SYS_CLK_FREQ 66000000 #else #define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */ #endif /* below can be toggled for performance analysis. otherwise use default */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #undef CONFIG_BTB /* toggle branch predition */ #define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00400000 #if defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) #error "You can only use either PCI Ethernet Card or TSEC Ethernet, not both." #endif /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is now 256MB */ #if defined(CONFIG_RAM_AS_FLASH) #define CONFIG_SYS_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ #else #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ #endif #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 0MB */ #if defined(CONFIG_RAM_AS_FLASH) #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ #define CONFIG_SYS_BR0_PRELIM 0xf8001801 /* port size 32bit */ #else /* Boot from real Flash */ #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ #define CONFIG_SYS_BR0_PRELIM 0xff801001 /* port size 16bit */ #endif #define CONFIG_SYS_OR0_PRELIM 0xff806f67 /* 8MB Flash */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms)*/ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms)*/ #define CONFIG_SYS_FLASH_CFI 1 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #define CONFIG_SYS_RAMBOOT #else #undef CONFIG_SYS_RAMBOOT #endif /* DDR Setup */ #define CONFIG_FSL_DDR1 #undef CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #define CONFIG_DDR_SPD #define CONFIG_DDR_DLL /* possible DLL fix needed */ #undef CONFIG_DDR_ECC /* only for ECC DDR module */ #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_VERY_BIG_RAM #define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 /* I2C addresses of SPD EEPROMs */ #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ #undef CONFIG_CLOCKS_IN_MHZ /* local bus definitions */ #define CONFIG_SYS_BR2_PRELIM 0xf0001861 /* 64MB localbus SDRAM */ #define CONFIG_SYS_OR2_PRELIM 0xfc006901 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* local bus freq divider*/ #define CONFIG_SYS_LBC_LBCR 0x00000000 #define CONFIG_SYS_LBC_LSRT 0x20000000 #define CONFIG_SYS_LBC_MRTPR 0x20000000 #define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 #define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 #define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 #define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 #define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 #if defined(CONFIG_RAM_AS_FLASH) #define CONFIG_SYS_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ #else #define CONFIG_SYS_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ #endif #define CONFIG_SYS_OR4_PRELIM 0xffffe1f1 #define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) #define CONFIG_SYS_INIT_RAM_LOCK 1 #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* * I2C */ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ #define CONFIG_SYS_I2C_OFFSET 0x3000 /* General PCI */ #define CONFIG_SYS_PCI_MEM_BASE 0x80000000 #define CONFIG_SYS_PCI_MEM_PHYS 0x80000000 #define CONFIG_SYS_PCI_MEM_SIZE 0x20000000 #define CONFIG_SYS_PCI_IO_BASE 0xe2000000 #if defined(CONFIG_PCI) #define CONFIG_NET_MULTI #undef CONFIG_EEPRO100 #define CONFIG_TULIP #define CONFIG_PCI_PNP /* do pci plug-and-play */ #if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 #define PCI_ENET0_MEMADDR 0xe0000000 #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/ #endif #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0008 #elif defined(CONFIG_TSEC_ENET) #define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_TSEC1 1 #define CONFIG_HAS_ETH0 #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_HAS_ETH1 #define CONFIG_TSEC2_NAME "TSEC1" #define CONFIG_MPC85XX_FEC 1 #define CONFIG_HAS_ETH2 #define CONFIG_MPC85XX_FEC_NAME "FEC" #define TSEC1_PHY_ADDR 7 #define TSEC2_PHY_ADDR 4 #define FEC_PHY_ADDR 2 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define FEC_PHYIDX 0 #define TSEC1_FLAGS TSEC_GIGABIT #define TSEC2_FLAGS TSEC_GIGABIT #define FEC_FLAGS 0 /* Options are: TSEC[0-1], FEC */ #define CONFIG_ETHPRIME "TSEC0" #define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */ #define INTEL_LXT971_PHY 1 #endif /* Environment */ #ifndef CONFIG_SYS_RAMBOOT #if defined(CONFIG_RAM_AS_FLASH) #define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x100000) #define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ #endif #define CONFIG_ENV_SIZE 0x2000 #else /* #define CONFIG_SYS_NO_FLASH 1 */ /* Flash is not usable now */ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200" #define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000" #define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_PING #define CONFIG_CMD_I2C #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #endif #if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) #undef CONFIG_CMD_SAVEENV #undef CONFIG_CMD_LOADS #endif #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "MPC8540EVAL=> "/* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /*****************************/ /* Environment Configuration */ /*****************************/ /* The mac addresses for all ethernet interface */ /* NOTE: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) #define CONFIG_ETHADDR 00:01:af:07:9b:8a #define CONFIG_ETH1ADDR 00:01:af:07:9b:8b #define CONFIG_ETH2ADDR 00:01:af:07:9b:8c #endif #define CONFIG_ROOTPATH /nfsroot #define CONFIG_BOOTFILE your.uImage #define CONFIG_SERVERIP 192.168.101.1 #define CONFIG_IPADDR 192.168.101.11 #define CONFIG_GATEWAYIP 192.168.101.0 #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ #define CONFIG_HOSTNAME MPC8540EVAL #endif /* __CONFIG_H */