1 files changed, 393 insertions, 248 deletions

diff --git a/drivers/char/ipmi/ipmi_bt_sm.c b/drivers/char/ipmi/ipmi_bt_sm.c
index 0030cd8e2e9..6c59baa887a 100644
--- a/drivers/char/ipmi/ipmi_bt_sm.c
+++ b/drivers/char/ipmi/ipmi_bt_sm.c
@@ -33,11 +33,13 @@
 #include <linux/ipmi_msgdefs.h>		/* for completion codes */
 #include "ipmi_si_sm.h"
 
-static int bt_debug = 0x00;	/* Production value 0, see following flags */
+#define BT_DEBUG_OFF	0	/* Used in production */
+#define BT_DEBUG_ENABLE	1	/* Generic messages */
+#define BT_DEBUG_MSG	2	/* Prints all request/response buffers */
+#define BT_DEBUG_STATES	4	/* Verbose look at state changes */
+
+static int bt_debug = BT_DEBUG_OFF;
 
-#define	BT_DEBUG_ENABLE	1
-#define BT_DEBUG_MSG	2
-#define BT_DEBUG_STATES	4
 module_param(bt_debug, int, 0644);
 MODULE_PARM_DESC(bt_debug, "debug bitmask, 1=enable, 2=messages, 4=states");
 
@@ -47,38 +49,54 @@ MODULE_PARM_DESC(bt_debug, "debug bitmask, 1=enable, 2=messages, 4=states");
    Since the Open IPMI architecture is single-message oriented at this
    stage, the queue depth of BT is of no concern. */
 
-#define BT_NORMAL_TIMEOUT	5000000	/* seconds in microseconds */
-#define BT_RETRY_LIMIT		2
-#define BT_RESET_DELAY		6000000	/* 6 seconds after warm reset */
+#define BT_NORMAL_TIMEOUT	5	/* seconds */
+#define BT_NORMAL_RETRY_LIMIT	2
+#define BT_RESET_DELAY		6	/* seconds after warm reset */
+
+/* States are written in chronological order and usually cover
+   multiple rows of the state table discussion in the IPMI spec. */
 
 enum bt_states {
-	BT_STATE_IDLE,
+	BT_STATE_IDLE = 0,	/* Order is critical in this list */
 	BT_STATE_XACTION_START,
 	BT_STATE_WRITE_BYTES,
-	BT_STATE_WRITE_END,
 	BT_STATE_WRITE_CONSUME,
-	BT_STATE_B2H_WAIT,
-	BT_STATE_READ_END,
-	BT_STATE_RESET1,		/* These must come last */
+	BT_STATE_READ_WAIT,
+	BT_STATE_CLEAR_B2H,
+	BT_STATE_READ_BYTES,
+	BT_STATE_RESET1,	/* These must come last */
 	BT_STATE_RESET2,
 	BT_STATE_RESET3,
 	BT_STATE_RESTART,
-	BT_STATE_HOSED
+	BT_STATE_PRINTME,
+	BT_STATE_CAPABILITIES_BEGIN,
+	BT_STATE_CAPABILITIES_END,
+	BT_STATE_LONG_BUSY	/* BT doesn't get hosed :-) */
 };
 
+/* Macros seen at the end of state "case" blocks.  They help with legibility
+   and debugging. */
+
+#define BT_STATE_CHANGE(X,Y) { bt->state = X; return Y; }
+
+#define BT_SI_SM_RETURN(Y)   { last_printed = BT_STATE_PRINTME; return Y; }
+
 struct si_sm_data {
 	enum bt_states	state;
-	enum bt_states	last_state;	/* assist printing and resets */
 	unsigned char	seq;		/* BT sequence number */
 	struct si_sm_io	*io;
-        unsigned char	write_data[IPMI_MAX_MSG_LENGTH];
-        int		write_count;
-        unsigned char	read_data[IPMI_MAX_MSG_LENGTH];
-        int		read_count;
-        int		truncated;
-        long		timeout;
-        unsigned int	error_retries;	/* end of "common" fields */
+	unsigned char	write_data[IPMI_MAX_MSG_LENGTH];
+	int		write_count;
+	unsigned char	read_data[IPMI_MAX_MSG_LENGTH];
+	int		read_count;
+	int		truncated;
+	long		timeout;	/* microseconds countdown */
+	int		error_retries;	/* end of "common" fields */
 	int		nonzero_status;	/* hung BMCs stay all 0 */
+	enum bt_states	complete;	/* to divert the state machine */
+	int		BT_CAP_outreqs;
+	long		BT_CAP_req2rsp;
+	int		BT_CAP_retries;	/* Recommended retries */
 };
 
 #define BT_CLR_WR_PTR	0x01	/* See IPMI 1.5 table 11.6.4 */
@@ -111,86 +129,118 @@ struct si_sm_data {
 static char *state2txt(unsigned char state)
 {
 	switch (state) {
-		case BT_STATE_IDLE:		return("IDLE");
-		case BT_STATE_XACTION_START:	return("XACTION");
-		case BT_STATE_WRITE_BYTES:	return("WR_BYTES");
-		case BT_STATE_WRITE_END:	return("WR_END");
-		case BT_STATE_WRITE_CONSUME:	return("WR_CONSUME");
-		case BT_STATE_B2H_WAIT:		return("B2H_WAIT");
-		case BT_STATE_READ_END:		return("RD_END");
-		case BT_STATE_RESET1:		return("RESET1");
-		case BT_STATE_RESET2:		return("RESET2");
-		case BT_STATE_RESET3:		return("RESET3");
-		case BT_STATE_RESTART:		return("RESTART");
-		case BT_STATE_HOSED:		return("HOSED");
+	case BT_STATE_IDLE:		return("IDLE");
+	case BT_STATE_XACTION_START:	return("XACTION");
+	case BT_STATE_WRITE_BYTES:	return("WR_BYTES");
+	case BT_STATE_WRITE_CONSUME:	return("WR_CONSUME");
+	case BT_STATE_READ_WAIT:	return("RD_WAIT");
+	case BT_STATE_CLEAR_B2H:	return("CLEAR_B2H");
+	case BT_STATE_READ_BYTES:	return("RD_BYTES");
+	case BT_STATE_RESET1:		return("RESET1");
+	case BT_STATE_RESET2:		return("RESET2");
+	case BT_STATE_RESET3:		return("RESET3");
+	case BT_STATE_RESTART:		return("RESTART");
+	case BT_STATE_LONG_BUSY:	return("LONG_BUSY");
+	case BT_STATE_CAPABILITIES_BEGIN: return("CAP_BEGIN");
+	case BT_STATE_CAPABILITIES_END:	return("CAP_END");
 	}
 	return("BAD STATE");
 }
 #define STATE2TXT state2txt(bt->state)
 
-static char *status2txt(unsigned char status, char *buf)
+static char *status2txt(unsigned char status)
 {
+	/*
+	 * This cannot be called by two threads at the same time and
+	 * the buffer is always consumed immediately, so the static is
+	 * safe to use.
+	 */
+	static char buf[40];
+
 	strcpy(buf, "[ ");
-	if (status & BT_B_BUSY) strcat(buf, "B_BUSY ");
-	if (status & BT_H_BUSY) strcat(buf, "H_BUSY ");
-	if (status & BT_OEM0) strcat(buf, "OEM0 ");
-	if (status & BT_SMS_ATN) strcat(buf, "SMS ");
-	if (status & BT_B2H_ATN) strcat(buf, "B2H ");
-	if (status & BT_H2B_ATN) strcat(buf, "H2B ");
+	if (status & BT_B_BUSY)
+		strcat(buf, "B_BUSY ");
+	if (status & BT_H_BUSY)
+		strcat(buf, "H_BUSY ");
+	if (status & BT_OEM0)
+		strcat(buf, "OEM0 ");
+	if (status & BT_SMS_ATN)
+		strcat(buf, "SMS ");
+	if (status & BT_B2H_ATN)
+		strcat(buf, "B2H ");
+	if (status & BT_H2B_ATN)
+		strcat(buf, "H2B ");
 	strcat(buf, "]");
 	return buf;
 }
-#define STATUS2TXT(buf) status2txt(status, buf)
+#define STATUS2TXT status2txt(status)
+
+/* called externally at insmod time, and internally on cleanup */
 
-/* This will be called from within this module on a hosed condition */
-#define FIRST_SEQ	0
 static unsigned int bt_init_data(struct si_sm_data *bt, struct si_sm_io *io)
 {
-	bt->state = BT_STATE_IDLE;
-	bt->last_state = BT_STATE_IDLE;
-	bt->seq = FIRST_SEQ;
-	bt->io = io;
-	bt->write_count = 0;
-	bt->read_count = 0;
-	bt->error_retries = 0;
-	bt->nonzero_status = 0;
-	bt->truncated = 0;
-	bt->timeout = BT_NORMAL_TIMEOUT;
+	memset(bt, 0, sizeof(struct si_sm_data));
+	if (bt->io != io) {		/* external: one-time only things */
+		bt->io = io;
+		bt->seq = 0;
+	}
+	bt->state = BT_STATE_IDLE;	/* start here */
+	bt->complete = BT_STATE_IDLE;	/* end here */
+	bt->BT_CAP_req2rsp = BT_NORMAL_TIMEOUT * 1000000;
+	bt->BT_CAP_retries = BT_NORMAL_RETRY_LIMIT;
+	/* BT_CAP_outreqs == zero is a flag to read BT Capabilities */
 	return 3; /* We claim 3 bytes of space; ought to check SPMI table */
 }
 
+/* Jam a completion code (probably an error) into a response */
+
+static void force_result(struct si_sm_data *bt, unsigned char completion_code)
+{
+	bt->read_data[0] = 4;				/* # following bytes */
+	bt->read_data[1] = bt->write_data[1] | 4;	/* Odd NetFn/LUN */
+	bt->read_data[2] = bt->write_data[2];		/* seq (ignored) */
+	bt->read_data[3] = bt->write_data[3];		/* Command */
+	bt->read_data[4] = completion_code;
+	bt->read_count = 5;
+}
+
+/* The upper state machine starts here */
+
 static int bt_start_transaction(struct si_sm_data *bt,
 				unsigned char *data,
 				unsigned int size)
 {
 	unsigned int i;
 
-	if ((size < 2) || (size > (IPMI_MAX_MSG_LENGTH - 2)))
-	       return -1;
+	if (size < 2)
+		return IPMI_REQ_LEN_INVALID_ERR;
+	if (size > IPMI_MAX_MSG_LENGTH)
+		return IPMI_REQ_LEN_EXCEEDED_ERR;
 
-	if ((bt->state != BT_STATE_IDLE) && (bt->state != BT_STATE_HOSED))
-		return -2;
+	if (bt->state == BT_STATE_LONG_BUSY)
+		return IPMI_NODE_BUSY_ERR;
+
+	if (bt->state != BT_STATE_IDLE)
+		return IPMI_NOT_IN_MY_STATE_ERR;
 
 	if (bt_debug & BT_DEBUG_MSG) {
-    		printk(KERN_WARNING "+++++++++++++++++++++++++++++++++++++\n");
-		printk(KERN_WARNING "BT: write seq=0x%02X:", bt->seq);
+		printk(KERN_WARNING "BT: +++++++++++++++++ New command\n");
+		printk(KERN_WARNING "BT: NetFn/LUN CMD [%d data]:", size - 2);
 		for (i = 0; i < size; i ++)
-		       printk (" %02x", data[i]);
+			printk (" %02x", data[i]);
 		printk("\n");
 	}
 	bt->write_data[0] = size + 1;	/* all data plus seq byte */
 	bt->write_data[1] = *data;	/* NetFn/LUN */
-	bt->write_data[2] = bt->seq;
+	bt->write_data[2] = bt->seq++;
 	memcpy(bt->write_data + 3, data + 1, size - 1);
 	bt->write_count = size + 2;
-
 	bt->error_retries = 0;
 	bt->nonzero_status = 0;
-	bt->read_count = 0;
 	bt->truncated = 0;
 	bt->state = BT_STATE_XACTION_START;
-	bt->last_state = BT_STATE_IDLE;
-	bt->timeout = BT_NORMAL_TIMEOUT;
+	bt->timeout = bt->BT_CAP_req2rsp;
+	force_result(bt, IPMI_ERR_UNSPECIFIED);
 	return 0;
 }
 
@@ -198,38 +248,30 @@ static int bt_start_transaction(struct si_sm_data *bt,
    it calls this.  Strip out the length and seq bytes. */
 
 static int bt_get_result(struct si_sm_data *bt,
-			   unsigned char *data,
-			   unsigned int length)
+			 unsigned char *data,
+			 unsigned int length)
 {
 	int i, msg_len;
 
 	msg_len = bt->read_count - 2;		/* account for length & seq */
-	/* Always NetFn, Cmd, cCode */
 	if (msg_len < 3 || msg_len > IPMI_MAX_MSG_LENGTH) {
-		printk(KERN_DEBUG "BT results: bad msg_len = %d\n", msg_len);
-		data[0] = bt->write_data[1] | 0x4;	/* Kludge a response */
-		data[1] = bt->write_data[3];
-		data[2] = IPMI_ERR_UNSPECIFIED;
+		force_result(bt, IPMI_ERR_UNSPECIFIED);
 		msg_len = 3;
-	} else {
-		data[0] = bt->read_data[1];
-		data[1] = bt->read_data[3];
-		if (length < msg_len)
-		       bt->truncated = 1;
-		if (bt->truncated) {	/* can be set in read_all_bytes() */
-			data[2] = IPMI_ERR_MSG_TRUNCATED;
-			msg_len = 3;
-		} else
-		       memcpy(data + 2, bt->read_data + 4, msg_len - 2);
+	}
+	data[0] = bt->read_data[1];
+	data[1] = bt->read_data[3];
+	if (length < msg_len || bt->truncated) {
+		data[2] = IPMI_ERR_MSG_TRUNCATED;
+		msg_len = 3;
+	} else
+		memcpy(data + 2, bt->read_data + 4, msg_len - 2);
 
-		if (bt_debug & BT_DEBUG_MSG) {
-			printk (KERN_WARNING "BT: res (raw)");
-			for (i = 0; i < msg_len; i++)
-			       printk(" %02x", data[i]);
-			printk ("\n");
-		}
+	if (bt_debug & BT_DEBUG_MSG) {
+		printk (KERN_WARNING "BT: result %d bytes:", msg_len);
+		for (i = 0; i < msg_len; i++)
+			printk(" %02x", data[i]);
+		printk ("\n");
 	}
-	bt->read_count = 0;	/* paranoia */
 	return msg_len;
 }
 
@@ -238,22 +280,40 @@ static int bt_get_result(struct si_sm_data *bt,
 
 static void reset_flags(struct si_sm_data *bt)
 {
+	if (bt_debug)
+		printk(KERN_WARNING "IPMI BT: flag reset %s\n",
+					status2txt(BT_STATUS));
 	if (BT_STATUS & BT_H_BUSY)
-	       BT_CONTROL(BT_H_BUSY);
-	if (BT_STATUS & BT_B_BUSY)
-	       BT_CONTROL(BT_B_BUSY);
-	BT_CONTROL(BT_CLR_WR_PTR);
-	BT_CONTROL(BT_SMS_ATN);
-
-	if (BT_STATUS & BT_B2H_ATN) {
-		int i;
-		BT_CONTROL(BT_H_BUSY);
-		BT_CONTROL(BT_B2H_ATN);
-		BT_CONTROL(BT_CLR_RD_PTR);
-		for (i = 0; i < IPMI_MAX_MSG_LENGTH + 2; i++)
-		       BMC2HOST;
-		BT_CONTROL(BT_H_BUSY);
-	}
+		BT_CONTROL(BT_H_BUSY);	/* force clear */
+	BT_CONTROL(BT_CLR_WR_PTR);	/* always reset */
+	BT_CONTROL(BT_SMS_ATN);		/* always clear */
+	BT_INTMASK_W(BT_BMC_HWRST);
+}
+
+/* Get rid of an unwanted/stale response.  This should only be needed for
+   BMCs that support multiple outstanding requests. */
+
+static void drain_BMC2HOST(struct si_sm_data *bt)
+{
+	int i, size;
+
+	if (!(BT_STATUS & BT_B2H_ATN)) 	/* Not signalling a response */
+		return;
+
+	BT_CONTROL(BT_H_BUSY);		/* now set */
+	BT_CONTROL(BT_B2H_ATN);		/* always clear */
+	BT_STATUS;			/* pause */
+	BT_CONTROL(BT_B2H_ATN);		/* some BMCs are stubborn */
+	BT_CONTROL(BT_CLR_RD_PTR);	/* always reset */
+	if (bt_debug)
+		printk(KERN_WARNING "IPMI BT: stale response %s; ",
+			status2txt(BT_STATUS));
+	size = BMC2HOST;
+	for (i = 0; i < size ; i++)
+		BMC2HOST;
+	BT_CONTROL(BT_H_BUSY);		/* now clear */
+	if (bt_debug)
+		printk("drained %d bytes\n", size + 1);
 }
 
 static inline void write_all_bytes(struct si_sm_data *bt)
@@ -261,201 +321,256 @@ static inline void write_all_bytes(struct si_sm_data *bt)
 	int i;
 
 	if (bt_debug & BT_DEBUG_MSG) {
-    		printk(KERN_WARNING "BT: write %d bytes seq=0x%02X",
+		printk(KERN_WARNING "BT: write %d bytes seq=0x%02X",
 			bt->write_count, bt->seq);
 		for (i = 0; i < bt->write_count; i++)
 			printk (" %02x", bt->write_data[i]);
 		printk ("\n");
 	}
 	for (i = 0; i < bt->write_count; i++)
-	       HOST2BMC(bt->write_data[i]);
+		HOST2BMC(bt->write_data[i]);
 }
 
 static inline int read_all_bytes(struct si_sm_data *bt)
 {
 	unsigned char i;
 
+	/* length is "framing info", minimum = 4: NetFn, Seq, Cmd, cCode.
+	   Keep layout of first four bytes aligned with write_data[] */
+
 	bt->read_data[0] = BMC2HOST;
 	bt->read_count = bt->read_data[0];
-	if (bt_debug & BT_DEBUG_MSG)
-    		printk(KERN_WARNING "BT: read %d bytes:", bt->read_count);
 
-	/* minimum: length, NetFn, Seq, Cmd, cCode == 5 total, or 4 more
-	   following the length byte. */
 	if (bt->read_count < 4 || bt->read_count >= IPMI_MAX_MSG_LENGTH) {
 		if (bt_debug & BT_DEBUG_MSG)
-			printk("bad length %d\n", bt->read_count);
+			printk(KERN_WARNING "BT: bad raw rsp len=%d\n",
+				bt->read_count);
 		bt->truncated = 1;
 		return 1;	/* let next XACTION START clean it up */
 	}
 	for (i = 1; i <= bt->read_count; i++)
-	       bt->read_data[i] = BMC2HOST;
-	bt->read_count++;	/* account for the length byte */
+		bt->read_data[i] = BMC2HOST;
+	bt->read_count++;	/* Account internally for length byte */
 
 	if (bt_debug & BT_DEBUG_MSG) {
-	    	for (i = 0; i < bt->read_count; i++)
+		int max = bt->read_count;
+
+		printk(KERN_WARNING "BT: got %d bytes seq=0x%02X",
+			max, bt->read_data[2]);
+		if (max > 16)
+			max = 16;
+		for (i = 0; i < max; i++)
 			printk (" %02x", bt->read_data[i]);
-	    	printk ("\n");
+		printk ("%s\n", bt->read_count == max ? "" : " ...");
 	}
-	if (bt->seq != bt->write_data[2])	/* idiot check */
-		printk(KERN_DEBUG "BT: internal error: sequence mismatch\n");
 
-	/* per the spec, the (NetFn, Seq, Cmd) tuples should match */
-	if ((bt->read_data[3] == bt->write_data[3]) &&		/* Cmd */
-        	(bt->read_data[2] == bt->write_data[2]) &&	/* Sequence */
-        	((bt->read_data[1] & 0xF8) == (bt->write_data[1] & 0xF8)))
+	/* per the spec, the (NetFn[1], Seq[2], Cmd[3]) tuples must match */
+	if ((bt->read_data[3] == bt->write_data[3]) &&
+	    (bt->read_data[2] == bt->write_data[2]) &&
+	    ((bt->read_data[1] & 0xF8) == (bt->write_data[1] & 0xF8)))
 			return 1;
 
 	if (bt_debug & BT_DEBUG_MSG)
-	       printk(KERN_WARNING "BT: bad packet: "
+		printk(KERN_WARNING "IPMI BT: bad packet: "
 		"want 0x(%02X, %02X, %02X) got (%02X, %02X, %02X)\n",
-		bt->write_data[1], bt->write_data[2], bt->write_data[3],
+		bt->write_data[1] | 0x04, bt->write_data[2], bt->write_data[3],
 		bt->read_data[1],  bt->read_data[2],  bt->read_data[3]);
 	return 0;
 }
 
-/* Modifies bt->state appropriately, need to get into the bt_event() switch */
+/* Restart if retries are left, or return an error completion code */
 
-static void error_recovery(struct si_sm_data *bt, char *reason)
+static enum si_sm_result error_recovery(struct si_sm_data *bt,
+					unsigned char status,
+					unsigned char cCode)
 {
-	unsigned char status;
-	char buf[40]; /* For getting status */
+	char *reason;
 
-	bt->timeout = BT_NORMAL_TIMEOUT; /* various places want to retry */
+	bt->timeout = bt->BT_CAP_req2rsp;
 
-	status = BT_STATUS;
-	printk(KERN_DEBUG "BT: %s in %s %s\n", reason, STATE2TXT,
-	       STATUS2TXT(buf));
+	switch (cCode) {
+	case IPMI_TIMEOUT_ERR:
+		reason = "timeout";
+		break;
+	default:
+		reason = "internal error";
+		break;
+	}
+
+	printk(KERN_WARNING "IPMI BT: %s in %s %s ", 	/* open-ended line */
+		reason, STATE2TXT, STATUS2TXT);
 
+	/* Per the IPMI spec, retries are based on the sequence number
+	   known only to this module, so manage a restart here. */
 	(bt->error_retries)++;
-	if (bt->error_retries > BT_RETRY_LIMIT) {
-		printk(KERN_DEBUG "retry limit (%d) exceeded\n", BT_RETRY_LIMIT);
-		bt->state = BT_STATE_HOSED;
-		if (!bt->nonzero_status)
-			printk(KERN_ERR "IPMI: BT stuck, try power cycle\n");
-		else if (bt->error_retries <= BT_RETRY_LIMIT + 1) {
-			printk(KERN_DEBUG "IPMI: BT reset (takes 5 secs)\n");
-        		bt->state = BT_STATE_RESET1;
-		}
-	return;
+	if (bt->error_retries < bt->BT_CAP_retries) {
+		printk("%d retries left\n",
+			bt->BT_CAP_retries - bt->error_retries);
+		bt->state = BT_STATE_RESTART;
+		return SI_SM_CALL_WITHOUT_DELAY;
 	}
 
-	/* Sometimes the BMC queues get in an "off-by-one" state...*/
-	if ((bt->state == BT_STATE_B2H_WAIT) && (status & BT_B2H_ATN)) {
-    		printk(KERN_DEBUG "retry B2H_WAIT\n");
-		return;
+	printk("failed %d retries, sending error response\n",
+		bt->BT_CAP_retries);
+	if (!bt->nonzero_status)
+		printk(KERN_ERR "IPMI BT: stuck, try power cycle\n");
+
+	/* this is most likely during insmod */
+	else if (bt->seq <= (unsigned char)(bt->BT_CAP_retries & 0xFF)) {
+		printk(KERN_WARNING "IPMI: BT reset (takes 5 secs)\n");
+		bt->state = BT_STATE_RESET1;
+		return SI_SM_CALL_WITHOUT_DELAY;
 	}
 
-	printk(KERN_DEBUG "restart command\n");
-	bt->state = BT_STATE_RESTART;
+	/* Concoct a useful error message, set up the next state, and
+	   be done with this sequence. */
+
+	bt->state = BT_STATE_IDLE;
+	switch (cCode) {
+	case IPMI_TIMEOUT_ERR:
+		if (status & BT_B_BUSY) {
+			cCode = IPMI_NODE_BUSY_ERR;
+			bt->state = BT_STATE_LONG_BUSY;
+		}
+		break;
+	default:
+		break;
+	}
+	force_result(bt, cCode);
+	return SI_SM_TRANSACTION_COMPLETE;
 }
 
-/* Check the status and (possibly) advance the BT state machine.  The
-   default return is SI_SM_CALL_WITH_DELAY. */
+/* Check status and (usually) take action and change this state machine. */
 
 static enum si_sm_result bt_event(struct si_sm_data *bt, long time)
 {
-	unsigned char status;
-	char buf[40]; /* For getting status */
+	unsigned char status, BT_CAP[8];
+	static enum bt_states last_printed = BT_STATE_PRINTME;
 	int i;
 
 	status = BT_STATUS;
 	bt->nonzero_status |= status;
-
-	if ((bt_debug & BT_DEBUG_STATES) && (bt->state != bt->last_state))
+	if ((bt_debug & BT_DEBUG_STATES) && (bt->state != last_printed)) {
 		printk(KERN_WARNING "BT: %s %s TO=%ld - %ld \n",
 			STATE2TXT,
-			STATUS2TXT(buf),
+			STATUS2TXT,
 			bt->timeout,
 			time);
-	bt->last_state = bt->state;
+		last_printed = bt->state;
+	}
 
-	if (bt->state == BT_STATE_HOSED)
-	       return SI_SM_HOSED;
+	/* Commands that time out may still (eventually) provide a response.
+	   This stale response will get in the way of a new response so remove
+	   it if possible (hopefully during IDLE).  Even if it comes up later
+	   it will be rejected by its (now-forgotten) seq number. */
+
+	if ((bt->state < BT_STATE_WRITE_BYTES) && (status & BT_B2H_ATN)) {
+		drain_BMC2HOST(bt);
+		BT_SI_SM_RETURN(SI_SM_CALL_WITH_DELAY);
+	}
 
-	if (bt->state != BT_STATE_IDLE) {	/* do timeout test */
+	if ((bt->state != BT_STATE_IDLE) &&
+	    (bt->state <  BT_STATE_PRINTME)) {		/* check timeout */
 		bt->timeout -= time;
-		if ((bt->timeout < 0) && (bt->state < BT_STATE_RESET1)) {
-			error_recovery(bt, "timed out");
-			return SI_SM_CALL_WITHOUT_DELAY;
-		}
+		if ((bt->timeout < 0) && (bt->state < BT_STATE_RESET1))
+			return error_recovery(bt,
+					      status,
+					      IPMI_TIMEOUT_ERR);
 	}
 
 	switch (bt->state) {
 
-    	case BT_STATE_IDLE:	/* check for asynchronous messages */
+	/* Idle state first checks for asynchronous messages from another
+	   channel, then does some opportunistic housekeeping. */
+
+	case BT_STATE_IDLE:
 		if (status & BT_SMS_ATN) {
 			BT_CONTROL(BT_SMS_ATN);	/* clear it */
 			return SI_SM_ATTN;
 		}
-		return SI_SM_IDLE;
 
-	case BT_STATE_XACTION_START:
-		if (status & BT_H_BUSY) {
+		if (status & BT_H_BUSY)		/* clear a leftover H_BUSY */
 			BT_CONTROL(BT_H_BUSY);
-			break;
-		}
-    		if (status & BT_B2H_ATN)
-		       break;
-		bt->state = BT_STATE_WRITE_BYTES;
-		return SI_SM_CALL_WITHOUT_DELAY;	/* for logging */
 
-	case BT_STATE_WRITE_BYTES:
+		/* Read BT capabilities if it hasn't been done yet */
+		if (!bt->BT_CAP_outreqs)
+			BT_STATE_CHANGE(BT_STATE_CAPABILITIES_BEGIN,
+					SI_SM_CALL_WITHOUT_DELAY);
+		bt->timeout = bt->BT_CAP_req2rsp;
+		BT_SI_SM_RETURN(SI_SM_IDLE);
+
+	case BT_STATE_XACTION_START:
 		if (status & (BT_B_BUSY | BT_H2B_ATN))
-		       break;
+			BT_SI_SM_RETURN(SI_SM_CALL_WITH_DELAY);
+		if (BT_STATUS & BT_H_BUSY)
+			BT_CONTROL(BT_H_BUSY);	/* force clear */
+		BT_STATE_CHANGE(BT_STATE_WRITE_BYTES,
+				SI_SM_CALL_WITHOUT_DELAY);
+
+	case BT_STATE_WRITE_BYTES:
+		if (status & BT_H_BUSY)
+			BT_CONTROL(BT_H_BUSY);	/* clear */
 		BT_CONTROL(BT_CLR_WR_PTR);
 		write_all_bytes(bt);
-		BT_CONTROL(BT_H2B_ATN);	/* clears too fast to catch? */
-		bt->state = BT_STATE_WRITE_CONSUME;
-		return SI_SM_CALL_WITHOUT_DELAY; /* it MIGHT sail through */
-
-	case BT_STATE_WRITE_CONSUME: /* BMCs usually blow right thru here */
-        	if (status & (BT_H2B_ATN | BT_B_BUSY))
-		       break;
-		bt->state = BT_STATE_B2H_WAIT;
-		/* fall through with status */
-
-	/* Stay in BT_STATE_B2H_WAIT until a packet matches.  However, spinning
-	   hard here, constantly reading status, seems to hold off the
-	   generation of B2H_ATN so ALWAYS return CALL_WITH_DELAY. */
-
-	case BT_STATE_B2H_WAIT:
-    		if (!(status & BT_B2H_ATN))
-		       break;
-
-		/* Assume ordered, uncached writes: no need to wait */
-		if (!(status & BT_H_BUSY))
-		       BT_CONTROL(BT_H_BUSY); /* set */
-		BT_CONTROL(BT_B2H_ATN);		/* clear it, ACK to the BMC */
-		BT_CONTROL(BT_CLR_RD_PTR);	/* reset the queue */
-		i = read_all_bytes(bt);
-		BT_CONTROL(BT_H_BUSY);		/* clear */
-		if (!i)				/* Try this state again */
-		       break;
-		bt->state = BT_STATE_READ_END;
-		return SI_SM_CALL_WITHOUT_DELAY;	/* for logging */
-
-    	case BT_STATE_READ_END:
-
-		/* I could wait on BT_H_BUSY to go clear for a truly clean
-		   exit.  However, this is already done in XACTION_START
-		   and the (possible) extra loop/status/possible wait affects
-		   performance.  So, as long as it works, just ignore H_BUSY */
-
-#ifdef MAKE_THIS_TRUE_IF_NECESSARY
+		BT_CONTROL(BT_H2B_ATN);	/* can clear too fast to catch */
+		BT_STATE_CHANGE(BT_STATE_WRITE_CONSUME,
+				SI_SM_CALL_WITHOUT_DELAY);
 
-		if (status & BT_H_BUSY)
-		       break;
-#endif
-		bt->seq++;
-		bt->state = BT_STATE_IDLE;
-		return SI_SM_TRANSACTION_COMPLETE;
+	case BT_STATE_WRITE_CONSUME:
+		if (status & (BT_B_BUSY | BT_H2B_ATN))
+			BT_SI_SM_RETURN(SI_SM_CALL_WITH_DELAY);
+		BT_STATE_CHANGE(BT_STATE_READ_WAIT,
+				SI_SM_CALL_WITHOUT_DELAY);
+
+	/* Spinning hard can suppress B2H_ATN and force a timeout */
+
+	case BT_STATE_READ_WAIT:
+		if (!(status & BT_B2H_ATN))
+			BT_SI_SM_RETURN(SI_SM_CALL_WITH_DELAY);
+		BT_CONTROL(BT_H_BUSY);		/* set */
+
+		/* Uncached, ordered writes should just proceeed serially but
+		   some BMCs don't clear B2H_ATN with one hit.  Fast-path a
+		   workaround without too much penalty to the general case. */
+
+		BT_CONTROL(BT_B2H_ATN);		/* clear it to ACK the BMC */
+		BT_STATE_CHANGE(BT_STATE_CLEAR_B2H,
+				SI_SM_CALL_WITHOUT_DELAY);
+
+	case BT_STATE_CLEAR_B2H:
+		if (status & BT_B2H_ATN) {	/* keep hitting it */
+			BT_CONTROL(BT_B2H_ATN);
+			BT_SI_SM_RETURN(SI_SM_CALL_WITH_DELAY);
+		}
+		BT_STATE_CHANGE(BT_STATE_READ_BYTES,
+				SI_SM_CALL_WITHOUT_DELAY);
+
+	case BT_STATE_READ_BYTES:
+		if (!(status & BT_H_BUSY))	/* check in case of retry */
+			BT_CONTROL(BT_H_BUSY);
+		BT_CONTROL(BT_CLR_RD_PTR);	/* start of BMC2HOST buffer */
+		i = read_all_bytes(bt);		/* true == packet seq match */
+		BT_CONTROL(BT_H_BUSY);		/* NOW clear */
+		if (!i) 			/* Not my message */
+			BT_STATE_CHANGE(BT_STATE_READ_WAIT,
+					SI_SM_CALL_WITHOUT_DELAY);
+		bt->state = bt->complete;
+		return bt->state == BT_STATE_IDLE ?	/* where to next? */
+			SI_SM_TRANSACTION_COMPLETE :	/* normal */
+			SI_SM_CALL_WITHOUT_DELAY;	/* Startup magic */
+
+	case BT_STATE_LONG_BUSY:	/* For example: after FW update */
+		if (!(status & BT_B_BUSY)) {
+			reset_flags(bt);	/* next state is now IDLE */
+			bt_init_data(bt, bt->io);
+		}
+		return SI_SM_CALL_WITH_DELAY;	/* No repeat printing */
 
 	case BT_STATE_RESET1:
-    		reset_flags(bt);
-    		bt->timeout = BT_RESET_DELAY;
-		bt->state = BT_STATE_RESET2;
-		break;
+		reset_flags(bt);
+		drain_BMC2HOST(bt);
+		BT_STATE_CHANGE(BT_STATE_RESET2,
+				SI_SM_CALL_WITH_DELAY);
 
 	case BT_STATE_RESET2:		/* Send a soft reset */
 		BT_CONTROL(BT_CLR_WR_PTR);
@@ -464,29 +579,59 @@ static enum si_sm_result bt_event(struct si_sm_data *bt, long time)
 		HOST2BMC(42);		/* Sequence number */
 		HOST2BMC(3);		/* Cmd == Soft reset */
 		BT_CONTROL(BT_H2B_ATN);
-		bt->state = BT_STATE_RESET3;
-		break;
+		bt->timeout = BT_RESET_DELAY * 1000000;
+		BT_STATE_CHANGE(BT_STATE_RESET3,
+				SI_SM_CALL_WITH_DELAY);
 
-	case BT_STATE_RESET3:
+	case BT_STATE_RESET3:		/* Hold off everything for a bit */
 		if (bt->timeout > 0)
-		       return SI_SM_CALL_WITH_DELAY;
-		bt->state = BT_STATE_RESTART;	/* printk in debug modes */
-		break;
+			return SI_SM_CALL_WITH_DELAY;
+		drain_BMC2HOST(bt);
+		BT_STATE_CHANGE(BT_STATE_RESTART,
+				SI_SM_CALL_WITH_DELAY);
 
-	case BT_STATE_RESTART:		/* don't reset retries! */
-		reset_flags(bt);
-		bt->write_data[2] = ++bt->seq;
+	case BT_STATE_RESTART:		/* don't reset retries or seq! */
 		bt->read_count = 0;
 		bt->nonzero_status = 0;
-		bt->timeout = BT_NORMAL_TIMEOUT;
-		bt->state = BT_STATE_XACTION_START;
-		break;
-
-	default:	/* HOSED is supposed to be caught much earlier */
-		error_recovery(bt, "internal logic error");
-		break;
-  	}
-  	return SI_SM_CALL_WITH_DELAY;
+		bt->timeout = bt->BT_CAP_req2rsp;
+		BT_STATE_CHANGE(BT_STATE_XACTION_START,
+				SI_SM_CALL_WITH_DELAY);
+
+	/* Get BT Capabilities, using timing of upper level state machine.
+	   Set outreqs to prevent infinite loop on timeout. */
+	case BT_STATE_CAPABILITIES_BEGIN:
+		bt->BT_CAP_outreqs = 1;
+		{
+			unsigned char GetBT_CAP[] = { 0x18, 0x36 };
+			bt->state = BT_STATE_IDLE;
+			bt_start_transaction(bt, GetBT_CAP, sizeof(GetBT_CAP));
+		}
+		bt->complete = BT_STATE_CAPABILITIES_END;
+		BT_STATE_CHANGE(BT_STATE_XACTION_START,
+				SI_SM_CALL_WITH_DELAY);
+
+	case BT_STATE_CAPABILITIES_END:
+		i = bt_get_result(bt, BT_CAP, sizeof(BT_CAP));
+		bt_init_data(bt, bt->io);
+		if ((i == 8) && !BT_CAP[2]) {
+			bt->BT_CAP_outreqs = BT_CAP[3];
+			bt->BT_CAP_req2rsp = BT_CAP[6] * 1000000;
+			bt->BT_CAP_retries = BT_CAP[7];
+		} else
+			printk(KERN_WARNING "IPMI BT: using default values\n");
+		if (!bt->BT_CAP_outreqs)
+			bt->BT_CAP_outreqs = 1;
+		printk(KERN_WARNING "IPMI BT: req2rsp=%ld secs retries=%d\n",
+			bt->BT_CAP_req2rsp / 1000000L, bt->BT_CAP_retries);
+		bt->timeout = bt->BT_CAP_req2rsp;
+		return SI_SM_CALL_WITHOUT_DELAY;
+
+	default:	/* should never occur */
+		return error_recovery(bt,
+				      status,
+				      IPMI_ERR_UNSPECIFIED);
+	}
+	return SI_SM_CALL_WITH_DELAY;
 }
 
 static int bt_detect(struct si_sm_data *bt)
@@ -497,7 +642,7 @@ static int bt_detect(struct si_sm_data *bt)
 	   test that first.  The calling routine uses negative logic. */
 
 	if ((BT_STATUS == 0xFF) && (BT_INTMASK_R == 0xFF))
-	       return 1;
+		return 1;
 	reset_flags(bt);
 	return 0;
 }
@@ -513,11 +658,11 @@ static int bt_size(void)
 
 struct si_sm_handlers bt_smi_handlers =
 {
-	.init_data         = bt_init_data,
-	.start_transaction = bt_start_transaction,
-	.get_result        = bt_get_result,
-	.event             = bt_event,
-	.detect            = bt_detect,
-	.cleanup           = bt_cleanup,
-	.size              = bt_size,
+	.init_data		= bt_init_data,
+	.start_transaction	= bt_start_transaction,
+	.get_result		= bt_get_result,
+	.event			= bt_event,
+	.detect			= bt_detect,
+	.cleanup		= bt_cleanup,
+	.size			= bt_size,
 };