diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-omap3evm.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3evm.c | 246 |
1 files changed, 46 insertions, 200 deletions
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 5a1a916e5cc..b4d43464a30 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -44,12 +44,13 @@ #include <plat/usb.h> #include <plat/common.h> #include <plat/mcspi.h> -#include <plat/display.h> -#include <plat/panel-generic-dpi.h> +#include <video/omapdss.h> +#include <video/omap-panel-generic-dpi.h> #include "mux.h" #include "sdram-micron-mt46h32m32lf-6.h" #include "hsmmc.h" +#include "common-board-devices.h" #define OMAP3_EVM_TS_GPIO 175 #define OMAP3_EVM_EHCI_VBUS 22 @@ -101,49 +102,20 @@ static void __init omap3_evm_get_revision(void) } #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) -static struct resource omap3evm_smsc911x_resources[] = { - [0] = { - .start = OMAP3EVM_ETHR_START, - .end = (OMAP3EVM_ETHR_START + OMAP3EVM_ETHR_SIZE - 1), - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ), - .end = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ), - .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW), - }, -}; +#include <plat/gpmc-smsc911x.h> -static struct smsc911x_platform_config smsc911x_config = { - .phy_interface = PHY_INTERFACE_MODE_MII, - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, - .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS), -}; - -static struct platform_device omap3evm_smsc911x_device = { - .name = "smsc911x", - .id = -1, - .num_resources = ARRAY_SIZE(omap3evm_smsc911x_resources), - .resource = &omap3evm_smsc911x_resources[0], - .dev = { - .platform_data = &smsc911x_config, - }, +static struct omap_smsc911x_platform_data smsc911x_cfg = { + .cs = OMAP3EVM_SMSC911X_CS, + .gpio_irq = OMAP3EVM_ETHR_GPIO_IRQ, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, }; static inline void __init omap3evm_init_smsc911x(void) { - int eth_cs, eth_rst; struct clk *l3ck; unsigned int rate; - if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) - eth_rst = OMAP3EVM_GEN1_ETHR_GPIO_RST; - else - eth_rst = OMAP3EVM_GEN2_ETHR_GPIO_RST; - - eth_cs = OMAP3EVM_SMSC911X_CS; - l3ck = clk_get(NULL, "l3_ck"); if (IS_ERR(l3ck)) rate = 100000000; @@ -152,33 +124,13 @@ static inline void __init omap3evm_init_smsc911x(void) /* Configure ethernet controller reset gpio */ if (cpu_is_omap3430()) { - if (gpio_request(eth_rst, "SMSC911x gpio") < 0) { - pr_err(KERN_ERR "Failed to request %d for smsc911x\n", - eth_rst); - return; - } - - if (gpio_direction_output(eth_rst, 1) < 0) { - pr_err(KERN_ERR "Failed to set direction of %d for" \ - " smsc911x\n", eth_rst); - return; - } - /* reset pulse to ethernet controller*/ - usleep_range(150, 220); - gpio_set_value(eth_rst, 0); - usleep_range(150, 220); - gpio_set_value(eth_rst, 1); - usleep_range(1, 2); - } - - if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) { - printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", - OMAP3EVM_ETHR_GPIO_IRQ); - return; + if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) + smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST; + else + smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST; } - gpio_direction_input(OMAP3EVM_ETHR_GPIO_IRQ); - platform_device_register(&omap3evm_smsc911x_device); + gpmc_smsc911x_init(&smsc911x_cfg); } #else @@ -197,6 +149,15 @@ static inline void __init omap3evm_init_smsc911x(void) { return; } #define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210 #define OMAP3EVM_DVI_PANEL_EN_GPIO 199 +static struct gpio omap3_evm_dss_gpios[] __initdata = { + { OMAP3EVM_LCD_PANEL_RESB, GPIOF_OUT_INIT_HIGH, "lcd_panel_resb" }, + { OMAP3EVM_LCD_PANEL_INI, GPIOF_OUT_INIT_HIGH, "lcd_panel_ini" }, + { OMAP3EVM_LCD_PANEL_QVGA, GPIOF_OUT_INIT_LOW, "lcd_panel_qvga" }, + { OMAP3EVM_LCD_PANEL_LR, GPIOF_OUT_INIT_HIGH, "lcd_panel_lr" }, + { OMAP3EVM_LCD_PANEL_UD, GPIOF_OUT_INIT_HIGH, "lcd_panel_ud" }, + { OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW, "lcd_panel_envdd" }, +}; + static int lcd_enabled; static int dvi_enabled; @@ -204,61 +165,10 @@ static void __init omap3_evm_display_init(void) { int r; - r = gpio_request(OMAP3EVM_LCD_PANEL_RESB, "lcd_panel_resb"); - if (r) { - printk(KERN_ERR "failed to get lcd_panel_resb\n"); - return; - } - gpio_direction_output(OMAP3EVM_LCD_PANEL_RESB, 1); - - r = gpio_request(OMAP3EVM_LCD_PANEL_INI, "lcd_panel_ini"); - if (r) { - printk(KERN_ERR "failed to get lcd_panel_ini\n"); - goto err_1; - } - gpio_direction_output(OMAP3EVM_LCD_PANEL_INI, 1); - - r = gpio_request(OMAP3EVM_LCD_PANEL_QVGA, "lcd_panel_qvga"); - if (r) { - printk(KERN_ERR "failed to get lcd_panel_qvga\n"); - goto err_2; - } - gpio_direction_output(OMAP3EVM_LCD_PANEL_QVGA, 0); - - r = gpio_request(OMAP3EVM_LCD_PANEL_LR, "lcd_panel_lr"); - if (r) { - printk(KERN_ERR "failed to get lcd_panel_lr\n"); - goto err_3; - } - gpio_direction_output(OMAP3EVM_LCD_PANEL_LR, 1); - - r = gpio_request(OMAP3EVM_LCD_PANEL_UD, "lcd_panel_ud"); - if (r) { - printk(KERN_ERR "failed to get lcd_panel_ud\n"); - goto err_4; - } - gpio_direction_output(OMAP3EVM_LCD_PANEL_UD, 1); - - r = gpio_request(OMAP3EVM_LCD_PANEL_ENVDD, "lcd_panel_envdd"); - if (r) { - printk(KERN_ERR "failed to get lcd_panel_envdd\n"); - goto err_5; - } - gpio_direction_output(OMAP3EVM_LCD_PANEL_ENVDD, 0); - - return; - -err_5: - gpio_free(OMAP3EVM_LCD_PANEL_UD); -err_4: - gpio_free(OMAP3EVM_LCD_PANEL_LR); -err_3: - gpio_free(OMAP3EVM_LCD_PANEL_QVGA); -err_2: - gpio_free(OMAP3EVM_LCD_PANEL_INI); -err_1: - gpio_free(OMAP3EVM_LCD_PANEL_RESB); - + r = gpio_request_array(omap3_evm_dss_gpios, + ARRAY_SIZE(omap3_evm_dss_gpios)); + if (r) + printk(KERN_ERR "failed to get lcd_panel_* gpios\n"); } static int omap3_evm_enable_lcd(struct omap_dss_device *dssdev) @@ -448,7 +358,7 @@ static struct platform_device leds_gpio = { static int omap3evm_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) { - int r; + int r, lcd_bl_en; /* gpio + 0 is "mmc0_cd" (input/IRQ) */ omap_mux_init_gpio(63, OMAP_PIN_INPUT); @@ -465,16 +375,14 @@ static int omap3evm_twl_gpio_setup(struct device *dev, */ /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */ - r = gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL"); - if (!r) - r = gpio_direction_output(gpio + TWL4030_GPIO_MAX, - (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) ? 1 : 0); + lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ? + GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW; + r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL"); if (r) printk(KERN_ERR "failed to get/set lcd_bkl gpio\n"); /* gpio + 7 == DVI Enable */ - gpio_request(gpio + 7, "EN_DVI"); - gpio_direction_output(gpio + 7, 0); + gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI"); /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; @@ -652,78 +560,18 @@ static struct twl4030_platform_data omap3evm_twldata = { .vdac = &omap3_evm_vdac, .vpll2 = &omap3_evm_vpll2, .vio = &omap3evm_vio, -}; - -static struct i2c_board_info __initdata omap3evm_i2c_boardinfo[] = { - { - I2C_BOARD_INFO("twl4030", 0x48), - .flags = I2C_CLIENT_WAKE, - .irq = INT_34XX_SYS_NIRQ, - .platform_data = &omap3evm_twldata, - }, + .vmmc1 = &omap3evm_vmmc1, + .vsim = &omap3evm_vsim, }; static int __init omap3_evm_i2c_init(void) { - /* - * REVISIT: These entries can be set in omap3evm_twl_data - * after a merge with MFD tree - */ - omap3evm_twldata.vmmc1 = &omap3evm_vmmc1; - omap3evm_twldata.vsim = &omap3evm_vsim; - - omap_register_i2c_bus(1, 2600, omap3evm_i2c_boardinfo, - ARRAY_SIZE(omap3evm_i2c_boardinfo)); + omap3_pmic_init("twl4030", &omap3evm_twldata); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, NULL, 0); return 0; } -static void ads7846_dev_init(void) -{ - if (gpio_request(OMAP3_EVM_TS_GPIO, "ADS7846 pendown") < 0) - printk(KERN_ERR "can't get ads7846 pen down GPIO\n"); - - gpio_direction_input(OMAP3_EVM_TS_GPIO); - gpio_set_debounce(OMAP3_EVM_TS_GPIO, 310); -} - -static int ads7846_get_pendown_state(void) -{ - return !gpio_get_value(OMAP3_EVM_TS_GPIO); -} - -static struct ads7846_platform_data ads7846_config = { - .x_max = 0x0fff, - .y_max = 0x0fff, - .x_plate_ohms = 180, - .pressure_max = 255, - .debounce_max = 10, - .debounce_tol = 3, - .debounce_rep = 1, - .get_pendown_state = ads7846_get_pendown_state, - .keep_vref_on = 1, - .settle_delay_usecs = 150, - .wakeup = true, -}; - -static struct omap2_mcspi_device_config ads7846_mcspi_config = { - .turbo_mode = 0, - .single_channel = 1, /* 0: slave, 1: master */ -}; - -static struct spi_board_info omap3evm_spi_board_info[] = { - [0] = { - .modalias = "ads7846", - .bus_num = 1, - .chip_select = 0, - .max_speed_hz = 1500000, - .controller_data = &ads7846_mcspi_config, - .irq = OMAP_GPIO_IRQ(OMAP3_EVM_TS_GPIO), - .platform_data = &ads7846_config, - }, -}; - static struct omap_board_config_kernel omap3_evm_config[] __initdata = { }; @@ -825,6 +673,11 @@ static struct omap_musb_board_data musb_board_data = { .power = 100, }; +static struct gpio omap3_evm_ehci_gpios[] __initdata = { + { OMAP3_EVM_EHCI_VBUS, GPIOF_OUT_INIT_HIGH, "enable EHCI VBUS" }, + { OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW, "select EHCI port" }, +}; + static void __init omap3_evm_init(void) { omap3_evm_get_revision(); @@ -841,9 +694,6 @@ static void __init omap3_evm_init(void) omap_display_init(&omap3_evm_dss_data); - spi_register_board_info(omap3evm_spi_board_info, - ARRAY_SIZE(omap3evm_spi_board_info)); - omap_serial_init(); /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */ @@ -851,16 +701,12 @@ static void __init omap3_evm_init(void) if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) { /* enable EHCI VBUS using GPIO22 */ - omap_mux_init_gpio(22, OMAP_PIN_INPUT_PULLUP); - gpio_request(OMAP3_EVM_EHCI_VBUS, "enable EHCI VBUS"); - gpio_direction_output(OMAP3_EVM_EHCI_VBUS, 0); - gpio_set_value(OMAP3_EVM_EHCI_VBUS, 1); - + omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP); /* Select EHCI port on main board */ - omap_mux_init_gpio(61, OMAP_PIN_INPUT_PULLUP); - gpio_request(OMAP3_EVM_EHCI_SELECT, "select EHCI port"); - gpio_direction_output(OMAP3_EVM_EHCI_SELECT, 0); - gpio_set_value(OMAP3_EVM_EHCI_SELECT, 0); + omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT, + OMAP_PIN_INPUT_PULLUP); + gpio_request_array(omap3_evm_ehci_gpios, + ARRAY_SIZE(omap3_evm_ehci_gpios)); /* setup EHCI phy reset config */ omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP); @@ -876,7 +722,7 @@ static void __init omap3_evm_init(void) } usb_musb_init(&musb_board_data); usbhs_init(&usbhs_bdata); - ads7846_dev_init(); + omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL); omap3evm_init_smsc911x(); omap3_evm_display_init(); |