/* * (C) Copyright 2007 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * Configuation settings for the SMN42 board from Siemens. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #ifndef __CONFIG_H #define __CONFIG_H /* * If we are developing, we might want to start u-boot from ram * so we MUST NOT initialize critical regs like mem-timing ... */ #undef CONFIG_SKIP_LOWLEVEL_INIT #undef CONFIG_SKIP_RELOCATE_UBOOT /* * High Level Configuration Options * (easy to change) */ #define CONFIG_ARM7 1 /* This is a ARM7 CPU */ #define CONFIG_ARM_THUMB 1 /* this is an ARM720TDMI */ #define CONFIG_LPC2292 #undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */ #undef CONFIG_USE_IRQ /* don't need them anymore */ /* * Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ /* * Hardware drivers */ /* * select serial console configuration */ #define CONFIG_LPC2292_SERIAL #define CONFIG_SERIAL1 1 /* we use Serial line 1 */ /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_BAUDRATE 115200 /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE /* enable I2C and select the hardware/software driver */ #undef CONFIG_HARD_I2C /* I2C with hardware support */ #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ /* this would be 0xAE if E0, E1 and E2 were pulled high */ #define CONFIG_SYS_I2C_SLAVE 0xA0 #define CONFIG_SYS_I2C_EEPROM_ADDR (0xA0 >> 1) #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes per write */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 /* not used but required by devices.c */ #define CONFIG_SYS_I2C_SPEED 10000 #ifdef CONFIG_SOFT_I2C /* * Software (bit-bang) I2C driver configuration */ #define SCL 0x00000004 /* P0.2 */ #define SDA 0x00000008 /* P0.3 */ #define I2C_READ ((GET32(IO0PIN) & SDA) ? 1 : 0) #define I2C_SDA(x) { if (x) PUT32(IO0SET, SDA); else PUT32(IO0CLR, SDA); } #define I2C_SCL(x) { if (x) PUT32(IO0SET, SCL); else PUT32(IO0CLR, SCL); } #define I2C_DELAY { udelay(100); } #define I2C_ACTIVE { unsigned int i2ctmp; \ i2ctmp = GET32(IO0DIR); \ i2ctmp |= SDA; \ PUT32(IO0DIR, i2ctmp); } #define I2C_TRISTATE { unsigned int i2ctmp; \ i2ctmp = GET32(IO0DIR); \ i2ctmp &= ~SDA; \ PUT32(IO0DIR, i2ctmp); } #endif /* CONFIG_SOFT_I2C */ /* * Command line configuration. */ #include #define CONFIG_CMD_DHCP #define CONFIG_CMD_FAT #define CONFIG_CMD_MMC #define CONFIG_CMD_NET #define CONFIG_CMD_EEPROM #define CONFIG_CMD_PING #define CONFIG_DOS_PARTITION #define CONFIG_BOOTDELAY 5 /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "SMN42 # " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x81800000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x83000000 /* 24 MB in SRAM */ #define CONFIG_SYS_LOAD_ADDR 0x81000000 /* default load address */ /* for uClinux img is here*/ #define CONFIG_SYS_SYS_CLK_FREQ 58982400 /* Hz */ #define CONFIG_SYS_HZ 2048 /* decrementer freq in Hz */ /* valid baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /*----------------------------------------------------------------------- * Stack sizes * * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128*1024) /* regular stack */ #ifdef CONFIG_USE_IRQ #define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ #define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ #endif /*----------------------------------------------------------------------- * Physical Memory Map */ #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SRAM */ #define PHYS_SDRAM_1 0x81000000 /* SRAM Bank #1 */ #define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB SRAM */ /* This is the external flash */ #define PHYS_FLASH_1 0x80000000 /* Flash Bank #1 */ #define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */ /*----------------------------------------------------------------------- * FLASH and environment organization */ /* * The first entry in CONFIG_SYS_FLASH_BANKS_LIST is a dummy, but it must be present. */ #define CONFIG_SYS_FLASH_BANKS_LIST { 0, PHYS_FLASH_1 } #define CONFIG_SYS_FLASH_ADDR0 0x555 #define CONFIG_SYS_FLASH_ADDR1 0x2AA #define CONFIG_SYS_FLASH_ERASE_TOUT 16384 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ #define CONFIG_ENV_IS_IN_FLASH 1 /* The Environment Sector is in the CPU-internal flash */ #define CONFIG_SYS_FLASH_BASE 0 #define CONFIG_ENV_OFFSET 0x3C000 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG #define CONFIG_MMC 1 /* we use this ethernet chip */ #define CONFIG_ENC28J60 #endif /* __CONFIG_H */