/* * (C) Copyright 2006, 2007 Detlev Zundel, dzu@denx.de * (C) Copyright 2005 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC852T 1 #define CONFIG_NC650 1 #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #undef CONFIG_8xx_CONS_SMC2 #undef CONFIG_8xx_CONS_NONE #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ /* * 10 MHz - PLL input clock */ #define CONFIG_8xx_OSCLK 10000000 /* * 50 MHz - default CPU clock */ #define CONFIG_8xx_CPUCLK_DEFAULT 50000000 /* * 15 MHz - CPU minimum clock */ #define CONFIG_SYS_8xx_CPUCLK_MIN 15000000 /* * 133 MHz - CPU maximum clock */ #define CONFIG_SYS_8xx_CPUCLK_MAX 133000000 #define CONFIG_SYS_MEASURE_CPUCLK #define CONFIG_SYS_8XX_XIN CONFIG_8xx_OSCLK #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #define CONFIG_AUTOBOOT_KEYED #define CONFIG_AUTOBOOT_PROMPT \ "\nEnter password - autoboot in %d seconds...\n", bootdelay #define CONFIG_AUTOBOOT_DELAY_STR "ids" #define CONFIG_BOOT_RETRY_TIME 900 #define CONFIG_BOOT_RETRY_MIN 30 #define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" #undef CONFIG_BOOTARGS #define CONFIG_BOOTCOMMAND \ "bootp;" \ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ "bootm" #define CONFIG_WATCHDOG /* watchdog enabled */ #undef CONFIG_STATUS_LED /* Status LED disabled */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_FEC_ENET 1 /* use FEC ethernet */ #define FEC_ENET #define CONFIG_MII #define CONFIG_SYS_DISCOVER_PHY 1 /* enable I2C and select the hardware/software driver */ #undef CONFIG_HARD_I2C /* I2C with hardware support */ #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ #define CONFIG_SYS_I2C_SLAVE 0x7f /* * Software (bit-bang) I2C driver configuration */ #if defined(CONFIG_IDS852_REV1) #define SCL 0x1000 /* PA 3 */ #define SDA 0x2000 /* PA 2 */ #define __I2C_DIR immr->im_ioport.iop_padir #define __I2C_DAT immr->im_ioport.iop_padat #define __I2C_PAR immr->im_ioport.iop_papar #elif defined(CONFIG_IDS852_REV2) #define SCL 0x0002 /* PB 30 */ #define SDA 0x0001 /* PB 31 */ #define __I2C_PAR immr->im_cpm.cp_pbpar #define __I2C_DIR immr->im_cpm.cp_pbdir #define __I2C_DAT immr->im_cpm.cp_pbdat #endif #define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \ __I2C_DIR |= (SDA|SCL); } #define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0) #define I2C_SDA(x) { if (x) __I2C_DAT |= SDA; else __I2C_DAT &= ~SDA; } #define I2C_SCL(x) { if (x) __I2C_DAT |= SCL; else __I2C_DAT &= ~SCL; } #define I2C_DELAY { udelay(5); } #define I2C_ACTIVE { __I2C_DIR |= SDA; } #define I2C_TRISTATE { __I2C_DIR &= ~SDA; } #define CONFIG_RTC_PCF8563 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* * Command line configuration. */ #include #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE #define CONFIG_CMD_DHCP #define CONFIG_CMD_I2C #define CONFIG_CMD_NAND #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NFS #define CONFIG_CMD_SNTP /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x00100000 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xF0000000 #define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0x40000000 #define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OFFSET 0x00740000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */ #define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment Sector */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif /* * NAND flash support */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) #endif /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 11-6 *----------------------------------------------------------------------- */ #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) /*----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 15-27 *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ #define SCCR_MASK SCCR_EBDF11 #define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | \ SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \ SCCR_DFLCD000 | SCCR_DFALCD00) /*----------------------------------------------------------------------- * *----------------------------------------------------------------------- * */ #define CONFIG_SYS_DER 0 /* * Init Memory Controller: * * BR0 and OR0 (FLASH) */ #define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ #define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ /* FLASH timing: Default value of OR0 after reset */ #define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \ OR_SCY_15_CLK | OR_TRLX) #define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V) /* * BR2 and OR2 (NAND Flash) - addressed through UPMB on rev 1 * rev2 only uses the chipselect */ #define CONFIG_SYS_NAND_BASE 0x50000000 #define CONFIG_SYS_NAND_SIZE 0x04000000 #define CONFIG_SYS_OR_TIMING_NAND (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ OR_SCY_15_CLK | OR_EHTR | OR_TRLX) #define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_MS_UPMB | BR_V ) #define CONFIG_SYS_OR2_PRELIM (((-CONFIG_SYS_NAND_SIZE) & OR_AM_MSK) | OR_BI ) /* * BR3 and OR3 (SDRAM) */ #define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ /* * SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ #define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 #define CONFIG_SYS_OR3_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM) #define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V) /* * BR4 and OR4 (CPLD) */ #define CONFIG_SYS_CPLD_BASE 0x80000000 /* CPLD */ #define CONFIG_SYS_CPLD_SIZE 0x10000 /* only 16 used */ #define CONFIG_SYS_OR_TIMING_CPLD (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ OR_SCY_1_CLK) #define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_CPLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) #define CONFIG_SYS_OR4_PRELIM (((-CONFIG_SYS_CPLD_SIZE) & OR_AM_MSK) | CONFIG_SYS_OR_TIMING_CPLD) /* * BR5 and OR5 (SRAM) */ #define CONFIG_SYS_SRAM_BASE 0x60000000 #define CONFIG_SYS_SRAM_SIZE 0x00080000 #define CONFIG_SYS_OR_TIMING_SRAM (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ OR_SCY_15_CLK | OR_EHTR | OR_TRLX) #define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_SRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) #define CONFIG_SYS_OR5_PRELIM (((-CONFIG_SYS_SRAM_SIZE) & OR_AM_MSK) | CONFIG_SYS_OR_TIMING_SRAM) #if defined(CONFIG_CP850) /* * BR6 and OR6 (DPRAM) - only on CP850 */ #define CONFIG_SYS_OR6_PRELIM 0xffff8170 #define CONFIG_SYS_BR6_PRELIM 0xa0000401 #define DPRAM_BASE_ADDR 0xa0000000 #define CONFIG_MISC_INIT_R 1 #endif /* * 4096 Rows from SDRAM example configuration * 1000 factor s -> ms * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration * 4 Number of refresh cycles per period * 64 Refresh cycle in ms per number of rows */ #define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64)) /* * Memory Periodic Timer Prescaler */ /* periodic timer for refresh */ #define CONFIG_SYS_MAMR_PTA 39 /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ /* * MAMR settings for SDRAM */ #define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) #define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) /* * MBMR settings for NAND flash */ #define CONFIG_SYS_MBMR_NAND ( MBMR_WLFB_5X ) /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ #define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ /* * JFFS2 partitions */ /* No command line, one static partition */ #undef CONFIG_CMD_MTDPARTS #define CONFIG_JFFS2_DEV "nand0" #define CONFIG_JFFS2_PART_SIZE 0x00400000 #define CONFIG_JFFS2_PART_OFFSET 0x00000000 /* mtdparts command line support */ #define CONFIG_CMD_MTDPARTS #define MTDIDS_DEFAULT "nor0=nc650-0,nand0=nc650-nand" #define MTDPARTS_DEFAULT "mtdparts=nc650-0:1m(kernel1),1m(kernel2)," \ "4m(cramfs1),1m(cramfs2)," \ "256k(u-boot),128k(env);" \ "nc650-nand:4m(jffs1),28m(jffs2)" #endif /* __CONFIG_H */