From 40039736f150348d61d27ffa55db65a087d249a7 Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Mon, 30 Jul 2012 16:13:10 -0700 Subject: am33xx: Remove board/ti/am335x/evm.c The intention has always been (and boards are to support) an i2c EEPROM that will identify what hardware they are, allowing a single binary to support multiple boards. As such, remove the 'evm.c' file as there is nothing EVM centric in it currently, only SoC peripheral configuration. Signed-off-by: Tom Rini --- arch/arm/cpu/armv7/am33xx/board.c | 173 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 173 insertions(+) (limited to 'arch') diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c index ec542fd05..4634a9ab4 100644 --- a/arch/arm/cpu/armv7/am33xx/board.c +++ b/arch/arm/cpu/armv7/am33xx/board.c @@ -17,6 +17,7 @@ */ #include +#include #include #include #include @@ -28,6 +29,9 @@ #include #include #include +#include +#include +#include DECLARE_GLOBAL_DATA_PTR; @@ -44,6 +48,79 @@ static const struct gpio_bank gpio_bank_am33xx[4] = { const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx; +/* MII mode defines */ +#define MII_MODE_ENABLE 0x0 +#define RGMII_MODE_ENABLE 0xA + +static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; + +/* + * I2C Address of on-board EEPROM + */ +#define I2C_BASE_BOARD_ADDR 0x50 + +#define NO_OF_MAC_ADDR 3 +#define ETH_ALEN 6 +#define NAME_LEN 8 + +struct am335x_baseboard_id { + unsigned int magic; + char name[NAME_LEN]; + char version[4]; + char serial[12]; + char config[32]; + char mac_addr[NO_OF_MAC_ADDR][ETH_ALEN]; +}; + +static struct am335x_baseboard_id header; + +static inline int board_is_bone(void) +{ + return !strncmp(header.name, "A335BONE", NAME_LEN); +} + +/* + * Read header information from EEPROM into global structure. + */ +static int read_eeprom(void) +{ + /* Check if baseboard eeprom is available */ + if (i2c_probe(I2C_BASE_BOARD_ADDR)) { + puts("Could not probe the EEPROM; something fundamentally " + "wrong on the I2C bus.\n"); + return -ENODEV; + } + + /* read the eeprom using i2c */ + if (i2c_read(I2C_BASE_BOARD_ADDR, 0, 2, (uchar *)&header, + sizeof(header))) { + puts("Could not read the EEPROM; something fundamentally" + " wrong on the I2C bus.\n"); + return -EIO; + } + + if (header.magic != 0xEE3355AA) { + /* + * read the eeprom using i2c again, + * but use only a 1 byte address + */ + if (i2c_read(I2C_BASE_BOARD_ADDR, 0, 1, (uchar *)&header, + sizeof(header))) { + puts("Could not read the EEPROM; something " + "fundamentally wrong on the I2C bus.\n"); + return -EIO; + } + + if (header.magic != 0xEE3355AA) { + printf("Incorrect magic number (0x%x) in EEPROM\n", + header.magic); + return -EINVAL; + } + } + + return 0; +} + /* UART Defines */ #ifdef CONFIG_SPL_BUILD #define UART_RESET (0x1 << 1) @@ -127,3 +204,99 @@ void setup_clocks_for_console(void) /* Not yet implemented */ return; } + +/* + * Basic board specific setup + */ +int board_init(void) +{ + enable_uart0_pin_mux(); + + enable_i2c0_pin_mux(); + enable_i2c1_pin_mux(); + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + if (read_eeprom() < 0) + puts("Could not get board ID.\n"); + + gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100; + + return 0; +} + +#ifdef CONFIG_DRIVER_TI_CPSW +static void cpsw_control(int enabled) +{ + /* VTP can be added here */ + + return; +} + +static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs = 0x208, + .sliver_reg_ofs = 0xd80, + .phy_id = 0, + }, + { + .slave_reg_ofs = 0x308, + .sliver_reg_ofs = 0xdc0, + .phy_id = 1, + }, +}; + +static struct cpsw_platform_data cpsw_data = { + .mdio_base = AM335X_CPSW_MDIO_BASE, + .cpsw_base = AM335X_CPSW_BASE, + .mdio_div = 0xff, + .channels = 8, + .cpdma_reg_ofs = 0x800, + .slaves = 1, + .slave_data = cpsw_slaves, + .ale_reg_ofs = 0xd00, + .ale_entries = 1024, + .host_port_reg_ofs = 0x108, + .hw_stats_reg_ofs = 0x900, + .mac_control = (1 << 5), + .control = cpsw_control, + .host_port_num = 0, + .version = CPSW_CTRL_VERSION_2, +}; + +int board_eth_init(bd_t *bis) +{ + uint8_t mac_addr[6]; + uint32_t mac_hi, mac_lo; + + if (!eth_getenv_enetaddr("ethaddr", mac_addr)) { + debug(" not set. Reading from E-fuse\n"); + /* try reading mac address from efuse */ + mac_lo = readl(&cdev->macid0l); + mac_hi = readl(&cdev->macid0h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("ethaddr", mac_addr); + else + return -1; + } + + if (board_is_bone()) { + enable_mii1_pin_mux(); + writel(MII_MODE_ENABLE, &cdev->miisel); + cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if = + PHY_INTERFACE_MODE_MII; + } else { + enable_rgmii1_pin_mux(); + writel(RGMII_MODE_ENABLE, &cdev->miisel); + cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if = + PHY_INTERFACE_MODE_RGMII; + } + + return cpsw_register(&cpsw_data); +} +#endif -- cgit v1.2.3