aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2012-08-14mxs: prefix register acessor macros with 'mxs' prefixOtavio Salvador
As the register accessing mode is the same for all i.MXS SoCs we ought to use 'mxs' prefix intead of 'mx28'. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-08-14MX28: SPI: Add DMA transfer supportMarek Vasut
The DMA transfers happen only if the transfered data are larger than 512 bytes. Otherwise PIO is used. This is a small speed optimization. The DMA transfer doesn't work if unaligned transfer is requested due to the limitation of the DMA controller. This has to be fixed by introducing generic bounce buffer. Therefore the DMA feature is now disabled by default. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2012-08-14MX28: SPI: Pull out the PIO transfer functionMarek Vasut
Pull out all the PIO transfer logic into separate function, so DMA can be added. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2012-08-14MX28: SPI: Refactor spi_xfer a bitMarek Vasut
This makes it easier to adapt for addition of DMA support. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2012-08-14arm : Atmel : add at91sam9x5ek board supportBo Shen
Add at91sam9x5ek board support, this board support the following SoCs AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35 Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up Signed-off-by: Bo Shen <voice.shen@atmel.com> [move MAINTAINERS entry to right place] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-08-05dm: Move OMAP GPIO driver to drivers/gpio/Marek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-08-05cpsw: add driver for cpsw ethernet deviceCyril Chemparathy
CPSW is an on-chip ethernet switch that is found on various SoCs from Texas Instruments. This patch adds a simple driver (based on the Linux driver) for this hardware module. This patch also adds support to clean and flush dcache during packet send and receive. Changes by Sandhya: Added support to clean and flush dcache during packet send/receive and added timeouts. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com> [Ilya: Cleaned cache handling, some style cleanup, some small fixes, use of internal RAM for descriptors] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-08-05serial/ns16550: ns16550 has a different register layout on SOC_DA8XXMikhail Kshevetskiy
also fix NS16550_init() as we need 16x divider Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com> Acked-by: Christian Riesch <christian.riesch@omicron.at> Tested-by: Christian Riesch <christian.riesch@omicron.at> Acked-by: Sughosh Ganu <urwithsughosh@gmail.com> Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
2012-08-05da850/omap-l138: Add support to read u-boot image from MMC/SDLad, Prabhakar
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will be in SPI flash and U-Boot image will be in MMC/SD card. SPL will do the low level initialization and then loads the u-boot image from MMC/SD card. Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138 configuration file to enable this feature. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-08-05omap24xx_i2c: add 2-byte address supportIlya Yanok
Various devices like EEPROMs require 2-byte address support to be properly accessed. This patch adds this support for OMAP2/3/4 I2C controller driver. I've tested it with EEPROM (16 bit address) and TPS65217 chip (8 bit address) on TI Beaglebone board. Unfortunately I don't have access to any compatible hardware with 16bit data register so I can't test if those #ifdef clauses really work. CC: Tom Rini <trini@ti.com> Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-07-31Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk
* 'master' of git://git.denx.de/u-boot-i2c: km/common: remove printfs for i2c deblocking code CONFIG: SMDK5250: I2C: Enable I2C I2C: Add support for Multi channel I2C: Modify the I2C driver for EXYNOS5 I2C: Move struct s3c24x0_i2c to a common place. EXYNOS: PINMUX: Add pinmux support for I2C EXYNOS5: define EXYNOS5_I2C_SPACING EXYNOS: Add I2C base address. EXYNOS: CLK: Add i2c clock mx6qsabrelite: add i2c multi-bus support imx-common: add i2c.c for bus recovery support i.mx53: add definition for I2C3_BASE_ADDR i.mx: iomux-v3.c: move to imx-common directory i.mx: iomux-v3.h: move to imx-common include directory iomux-v3: remove include of mx6x_pins.h mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support mxc_i2c: add bus recovery support mxc_i2c: prep work for multiple busses support mxc_i2c: add i2c_regs argument to i2c_imx_stop mxc_i2c: add retries mxc_i2c: check for arbitration lost mxc_i2c: change slave addr if conflicts with destination. mxc_i2c: don't disable controller after every transaction mxc_i2c: place i2c_reset code inline mxc_i2c: place imx_start code inline mxc_i2c: remove redundant read mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state mxc_i2c.c: code i2c_probe as a 0 length i2c_write mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write mxc_i2c: create i2c_init_transfer mxc_i2c: clear i2sr before waiting for bit mxc_i2c: create tx_byte function mxc_i2c: remove ifdef of CONFIG_HARD_I2C mxc_i2c: fix i2c_imx_stop i2c: deblock i2c bus also if accessed before realocation Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-31Merge branch 'master' of git://git.denx.de/u-boot-microblazeWolfgang Denk
* 'master' of git://git.denx.de/u-boot-microblaze: microblaze: Wire up SPI driver spi: microblaze: Adds driver for Xilinx SPI controller microblaze: intc: Clear interrupt code microblaze: Call serial multi initialization microblaze: Move __udelay implementation microblaze: Remove extern from board.c microblaze: Wire up dts configuration fdt: Add board specific dts inclusion microblaze: Move individual board linker scripts to common script in cpu tree. microblaze: Add gpio.h microblaze: Add missing undefs for UBI and UBIFS microblaze: Expand and correct configuration comments microblaze: Enable ubi support microblaze: Avoid compile error on systems without cfi flash microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION Conflicts: drivers/spi/Makefile Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-31I2C: Add support for Multi channelRajeshwari Shinde
This adds multiple i2c channel support for I2C. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31I2C: Modify the I2C driver for EXYNOS5Rajeshwari Shinde
This patch modifies the S3C I2C driver to suppport EXYNOS5. The cahnges made to driver are as follows: - I2C base address is passed as a parameter to many functions to avoid multiple #ifdef - Channel initialisation is moved to a commom funation as it is required by i2c_init. - Hardcoding for I2CCON_ACKGEN removed. - Replaced printf with debug. - Checkpatch issues resolved. - Pinmux setting will be done in board/samsung/smdk5250/smdk5250.c to avoid repeated setting of gpio lines, as it have multi bus support. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31I2C: Move struct s3c24x0_i2c to a common place.Rajeshwari Shinde
struct s3c24x0_i2c is being moved to common local header file so that the same can be used by s3c series and exynos series SoCs. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31i.mx: iomux-v3.h: move to imx-common include directoryTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS supportTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31mxc_i2c: add bus recovery supportTroy Kisky
Add support for calling a function that will toggle the SCL line to return the bus to idle condition. The actual toggling function is added in a later patch. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31mxc_i2c: prep work for multiple busses supportTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31mxc_i2c: add i2c_regs argument to i2c_imx_stopTroy Kisky
This is prep work for CONFIG_I2C_MULTI_BUS. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-31mxc_i2c: add retriesTroy Kisky
Retry unexpected hardware errors. This will not retry a received NAK. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31mxc_i2c: check for arbitration lostTroy Kisky
No need to continue waiting if arbitration lost. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-31mxc_i2c: change slave addr if conflicts with destination.Troy Kisky
The i2c controller cannot be both master and slave in the same transaction. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31mxc_i2c: don't disable controller after every transactionTroy Kisky
This helps in a multiple bus master environment which is why I also added a wait for bus idle. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31mxc_i2c: place i2c_reset code inlineTroy Kisky
imx_reset is only referenced once so move to that location. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-31mxc_i2c: place imx_start code inlineTroy Kisky
imx_start is only referenced once so move to that location. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-31mxc_i2c: remove redundant readTroy Kisky
wait_for_sr_state returns i2sr on success so no need to read again. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-31mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into ↵Troy Kisky
wait_for_sr_state Not using udelay gives a more accurate timeout. The current implementation of udelay in imx-common does not seem to wait at all for a udelay(1). Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> ---- V2: Added WATCHDOG_RESET as suggested by Marek Vasut add error message when stop fails mxc_i2c: code i2c_probe as a 0 length i2c_write Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31mxc_i2c.c: code i2c_probe as a 0 length i2c_writeTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_writeTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31mxc_i2c: create i2c_init_transferTroy Kisky
Initial code of i2c_read and i2c_write is identical, move to subroutine. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31mxc_i2c: clear i2sr before waiting for bitTroy Kisky
Let's clear the sr register before waiting for bit to be set, instead of clearing it after hardware sets it. No real operational difference here, but allows combining of i2c_imx_trx_complete and i2c_imx_bus_busy in later patches. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-31mxc_i2c: create tx_byte functionTroy Kisky
Use tx_byte function instead of having 3 copies of the code. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-31mxc_i2c: remove ifdef of CONFIG_HARD_I2CTroy Kisky
This is always selected when CONFIG_I2C_MXC is selected, so it adds no value. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-31mxc_i2c: fix i2c_imx_stopTroy Kisky
Instead of clearing 2 bits, all the other bits were set because '|=' was used instead of '&='. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31spi: microblaze: Adds driver for Xilinx SPI controllerStephan Linz
This is an improved version of the driver patch original submitted by Graeme Smecher <graeme.smecher@mail.mcgill.ca> The changes are: - remove hard coded Xilinx BSP defines (XPAR_SPI_*) and use CONFIG_SYS_SPI_BASE from config.h instead - add extensive register struct definitions - remove offset calculation for register access and use the new register struct instead - move default SPI controller configuration from spi_setup_slave() to spi_claim_bus() - add spi_set_speed() - insert SPI controller deactivation in spi_release_bus() - protect while loops in spi_xfer() with counter / timeouts - support SPI mode flags: LSB_FIRST, CPHA, CPOL, LOOP Come from: http://patchwork.ozlabs.org/patch/71797/ Signed-off-by: Stephan Linz <linz@li-pro.net> Tested-by: Michal Simek <monstr@monstr.eu>
2012-07-30Merge branch 'next' of git://git.denx.de/u-bootWolfgang Denk
* 'next' of git://git.denx.de/u-boot: MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c doc: cleanup - move board READMEs into respective board directories net: sh_eth: add support for SH7757's GETHER net: sh_eth: modify the definitions of regsiter net: sh_eth: add SH_ETH_TYPE_ condition net: sh_eth: clean up for the SH7757's code net: fec_mxc: Fix MDC for xMII net: fec_mxc: Fix setting of RCR for xMII net: nfs: make NFS_TIMEOUT configurable net: Inline the new eth_setenv_enetaddr_by_index function net: allow setting env enetaddr from net device setting net/designware: Consecutive writes to the same register to be avoided CACHE: net: asix: Fix asix driver to work with data cache on net: phy: micrel: make ksz9021 phy accessible net: abort network initialization if the PHY driver fails phylib: phy_startup() should return an error code on failure net: tftp: fix type of block arg to store_block Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-23net: sh_eth: add support for SH7757's GETHERYoshihiro Shimoda
SH7757 has 2 ETHERs and 2 GETHERs. This patch supports the SH7757's GETHER. If CONFIG_SH_ETHER_USE_GETHER is defined using SH7757, the driver handles the GETHER. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2012-07-23net: sh_eth: modify the definitions of regsiterYoshihiro Shimoda
The previous code had many similar definitions in each CPU. This patch borrows from the sh_eth driver of Linux kernel. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2012-07-23net: sh_eth: add SH_ETH_TYPE_ conditionYoshihiro Shimoda
At the moment, the driver supports the following CPUs: - GETHER (Gigabit Ethernet) : SH7763, SH7734 - ETHER (Fast Ethernet) : SH7724, SH7757 And the driver had the following "#if": #if defined(CONFIG_CPU_SH7763) || defined(CONFIG_CPU_SH7734) #if !defined(CONFIG_CPU_SH7757) && !defined(CONFIG_CPU_SH7724) - Those are for GETHER #if defined(CONFIG_CPU_SH7724) || defined(CONFIG_CPU_SH7757) - This is for ETHER So, for clean up the code, this patch adds SH_ETH_TYPE_GETHER and SH_ETH_TYPE_ETHER. And then, the patch modifies the above "#if". Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2012-07-23net: sh_eth: clean up for the SH7757's codeYoshihiro Shimoda
The SH7757's ETHER can work using the SH7724's setting. So, the patch modifies it. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2012-07-20Merge branch 'master' of git://git.denx.de/u-boot-usbWolfgang Denk
* 'master' of git://git.denx.de/u-boot-usb: usb_storage: fix ehci driver max transfer size smsc95xx: align buffers to cache line size ehci-hcd: change debug() to printf() in case of errors usb: check return value of submit_{control, bulk}_msg usb: pass cache-aligned buffer to usb_get_descriptor() ehci-hcd: fix external buffer cache handling ehci-hcd.c, musb_core, usb.h: Add USB_DMA_MINALIGN define for cache alignment ehci-hcd: program asynclistaddr before every transfer common.h: Introduce DEFINE_CACHE_ALIGN_BUFFER ehci-omap: Do not call dcache_off from omap_ehci_hcd_init Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-20Merge branch 'sf' of git://git.denx.de/u-boot-blackfinWolfgang Denk
* 'sf' of git://git.denx.de/u-boot-blackfin: sf: spansion: inline useless id defines sf: drop unused/duplicate command defines Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-20sf: spansion: inline useless id definesMike Frysinger
No need for dedicated defines when these really only get used once. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-07-20sf: drop unused/duplicate command definesMike Frysinger
In an effort to unify the spi flash drivers further, drop all the unused and/or duplicate command defines. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-07-19net: fec_mxc: Fix MDC for xMIIbenoit.thebaudeau@advans
The MDC signal is available on all xMII (i.e. 'not 7-wire') interfaces, so mii_speed has to be set for all these interfaces, and not only for MII. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
2012-07-19net: fec_mxc: Fix setting of RCR for xMIIbenoit.thebaudeau@advans
At least on i.MX25, the RMII mode did not work, which is fixed by this patch. The MII_MODE bit of the FEC RCR register means xMII, i.e. 'not 7-wire', so set it accordingly. According to the xMII and 7-wire (aka GPSI) standards, full duplex should be available on xMII, but not on 7-wire, so set FCE accordingly. The FEC may support full duplex for 7-wire too, but the reference manual does not say that, so avoid an invalid assumption. Actually, the choice between half and full duplex also depends on the endpoint/switch/repeater configuration, so a config option could be added for that, but there has been no need for it so far. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
2012-07-19Blackfin: bfin_mac: drop volatile markings on packet buffersMike Frysinger
Now that common code doesn't declare these as volatile, we don't need to either anymore. This fixes the build warning: bfin_mac.c: In function 'bfin_EMAC_recv': bfin_mac.c:193:23: warning: assignment discards qualifiers from pointer target type Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-07-18smsc95xx: align buffers to cache line sizeIlya Yanok
Align buffers passed to the USB code to cache line size so they can be DMAed safely. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-07-18ehci-hcd: change debug() to printf() in case of errorsIlya Yanok
Printing message could be useful if something goes really wrong. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-04-25 01:56:55 +0000