diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/README.p1022ds | 24 | ||||
| -rw-r--r-- | doc/README.p4080ds | 32 |
2 files changed, 56 insertions, 0 deletions
diff --git a/doc/README.p1022ds b/doc/README.p1022ds new file mode 100644 index 000000000..473ecf621 --- /dev/null +++ b/doc/README.p1022ds @@ -0,0 +1,24 @@ +Overview +-------- +P1022ds is a Low End Dual core platform supporting the P1022 processor +of QorIQ series. P1022 is an e500 based dual core SOC. + + +Pin Multiplex(hwconfig setting) +------------------------------- +Add the environment 'usb2', 'audclk' and 'tdm' to support pin multiplex +via hwconfig, i.e: +'setenv hwconfig usb2' to enable USB2 and disable eTsec2 +'setenv hwconfig tdm' to enable TDM and disable Audio +'setenv hwconfig audclk:12' to enable Audio(codec clock sources is 12MHz) + and disable TDM +'setenv hwconfig 'usb2;tdm' to enable USB2 and TDM, disable eTsec2 and Audio +'setenv hwconfig 'usb2;audclk:11' to enable USB2 and Audio(codec clock sources + is 11MHz), disable eTsec2 and TDM + +Warning: TDM and AUDIO can not enable simultaneous ! +and AUDIO codec clock sources only setting as 11MHz or 12MHz ! +'setenv hwconfig 'audclk:12;tdm' --- error ! +'setenv hwconfig 'audclk:11;tdm' --- error ! +'setenv hwconfig 'audclk:10' --- error ! + diff --git a/doc/README.p4080ds b/doc/README.p4080ds new file mode 100644 index 000000000..3ed59a8cf --- /dev/null +++ b/doc/README.p4080ds @@ -0,0 +1,32 @@ +Overview +-------- +The P4080DS is a Freescale reference board that hosts the eight-core P4080 SOC. + +SerDes hwconfig configuration +----------------------------- +The P4080 RCW includes three sets of bits the specify which SerDes lanes +should be powered down: SRDS_LPD_B1 (for bank one), SRDS_LPD_B2 (for bank two), +and SRDS_LPD_B3 (for bank three). Each of these contains four bits, one for +each lane in the bank. SerDes Erratum SERDES8 requires that SRDS_LPD_B2 and +SRDS_LPD_B3 be set to 0b1111. This forces banks two and three to be powered +down at reset. + +To re-enable these banks in U-Boot, two hwconfig are available: +"fsl_srds_lpd_b2" and "fsl_srds_lpd_b3". The value passed via fsl_srds_lpd_b2 +is written into SRDS_LPD_B2, and the value passed via fsl_srds_lpd_b3 is into +SRDS_LPD_B3. Each bit represents one of each bank, and a value of '1' +indicates that the lane should be powered down. + +For example, to indicate that both SerDes banks 2 and 3 are powered down, add +the following to hwconfig: + + serdes:fsl_srds_lpd_b2=0xf,fsl_srds_lpd_b3=0xf + +The "0xf" is a mask that corresponds to the 4 lanes A-D. The most significant +bit corresponds to lane A. To indicate that just lane A of bank 3 is to be +powered down, use: + + serdes:fsl_srds_lpd_b3=8 + +These options should be specified only if U-Boot does not automatically power +on the correct lanes. |