diff options
| -rw-r--r-- | MAINTAINERS | 4 | ||||
| -rw-r--r-- | board/taskit/stamp9g20/Makefile | 53 | ||||
| -rw-r--r-- | board/taskit/stamp9g20/led.c | 138 | ||||
| -rw-r--r-- | board/taskit/stamp9g20/stamp9g20.c | 191 | ||||
| -rw-r--r-- | boards.cfg | 2 | ||||
| -rw-r--r-- | include/configs/stamp9g20.h | 266 |
6 files changed, 654 insertions, 0 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 93f294fcd..0a9c92907 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -674,6 +674,10 @@ Vaibhav Hiremath <hvaibhav@ti.com> am3517_evm ARM ARMV7 (AM35x SoC) +Markus Hubig <mhubig@imko.de> + + STAMP9G20 ARM926EJS + Grazvydas Ignotas <notasas@gmail.com> omap3_pandora ARM ARMV7 (OMAP3xx SoC) diff --git a/board/taskit/stamp9g20/Makefile b/board/taskit/stamp9g20/Makefile new file mode 100644 index 000000000..4f17a27af --- /dev/null +++ b/board/taskit/stamp9g20/Makefile @@ -0,0 +1,53 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# (C) Copyright 2008 +# Stelian Pop <stelian@popies.net> +# Lead Tech Design <www.leadtechdesign.com> +# +# (C) Copyright 2012 +# Markus Hubig <mhubig@imko.de> +# IMKO GmbH <www.imko.de> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += stamp9g20.o +COBJS-y += led.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/taskit/stamp9g20/led.c b/board/taskit/stamp9g20/led.c new file mode 100644 index 000000000..197b4da5f --- /dev/null +++ b/board/taskit/stamp9g20/led.c @@ -0,0 +1,138 @@ +/* + * Copyright (c) 2009 Wind River Systems, Inc. + * Tom Rix <Tom.Rix@windriver.com> + * (C) Copyright 2009 + * Eric Benard <eric@eukrea.com> + * + * (C) Copyright 2012 + * Markus Hubig <mhubig@imko.de> + * IMKO GmbH <www.imko.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91_pmc.h> +#include <status_led.h> + +static unsigned int saved_state[3] = {STATUS_LED_OFF, + STATUS_LED_OFF, STATUS_LED_OFF}; + +void coloured_LED_init(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + + /* Enable the clock */ + writel(ATMEL_ID_PIOC, &pmc->pcer); + + at91_set_gpio_output(CONFIG_RED_LED, 1); + at91_set_gpio_output(CONFIG_GREEN_LED, 1); + at91_set_gpio_output(CONFIG_YELLOW_LED, 1); + + at91_set_gpio_value(CONFIG_RED_LED, 0); + at91_set_gpio_value(CONFIG_GREEN_LED, 1); + at91_set_gpio_value(CONFIG_YELLOW_LED, 0); +} + +void red_led_on(void) +{ + at91_set_gpio_value(CONFIG_RED_LED, 1); + saved_state[STATUS_LED_RED] = STATUS_LED_ON; +} + +void red_led_off(void) +{ + at91_set_gpio_value(CONFIG_RED_LED, 0); + saved_state[STATUS_LED_RED] = STATUS_LED_OFF; +} + +void green_led_on(void) +{ + at91_set_gpio_value(CONFIG_GREEN_LED, 1); + saved_state[STATUS_LED_GREEN] = STATUS_LED_ON; +} + +void green_led_off(void) +{ + at91_set_gpio_value(CONFIG_GREEN_LED, 0); + saved_state[STATUS_LED_GREEN] = STATUS_LED_OFF; +} + +void yellow_led_on(void) +{ + at91_set_gpio_value(CONFIG_YELLOW_LED, 1); + saved_state[STATUS_LED_YELLOW] = STATUS_LED_ON; +} + +void yellow_led_off(void) +{ + at91_set_gpio_value(CONFIG_YELLOW_LED, 0); + saved_state[STATUS_LED_YELLOW] = STATUS_LED_OFF; +} + +void __led_init(led_id_t mask, int state) +{ + __led_set(mask, state); +} + +void __led_toggle(led_id_t mask) +{ + if (STATUS_LED_RED == mask) { + if (STATUS_LED_ON == saved_state[STATUS_LED_RED]) + red_led_off(); + else + red_led_on(); + + } else if (STATUS_LED_GREEN == mask) { + if (STATUS_LED_ON == saved_state[STATUS_LED_GREEN]) + green_led_off(); + else + green_led_on(); + + } else if (STATUS_LED_YELLOW == mask) { + if (STATUS_LED_ON == saved_state[STATUS_LED_YELLOW]) + yellow_led_off(); + else + yellow_led_on(); + } +} + +void __led_set(led_id_t mask, int state) +{ + if (STATUS_LED_RED == mask) { + if (STATUS_LED_ON == state) + red_led_on(); + else + red_led_off(); + + } else if (STATUS_LED_GREEN == mask) { + if (STATUS_LED_ON == state) + green_led_on(); + else + green_led_off(); + + } else if (STATUS_LED_YELLOW == mask) { + if (STATUS_LED_ON == state) + yellow_led_on(); + else + yellow_led_off(); + } +} diff --git a/board/taskit/stamp9g20/stamp9g20.c b/board/taskit/stamp9g20/stamp9g20.c new file mode 100644 index 000000000..5e07bf8d4 --- /dev/null +++ b/board/taskit/stamp9g20/stamp9g20.c @@ -0,0 +1,191 @@ +/* + * (C) Copyright 2007-2008 + * Stelian Pop <stelian@popies.net> + * Lead Tech Design <www.leadtechdesign.com> + * + * Achim Ehrlich <aehrlich@taskit.de> + * taskit GmbH <www.taskit.de> + * + * (C) Copyright 2012- + * Markus Hubig <mhubig@imko.de> + * IMKO GmbH <www.imko.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/at91sam9260_matrix.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <watchdog.h> + +#ifdef CONFIG_MACB +# include <net.h> +# include <netdev.h> +#endif + +DECLARE_GLOBAL_DATA_PTR; + +static void stamp9G20_nand_hw_init(void) +{ + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; + unsigned long csa; + + /* Assign CS3 to NAND/SmartMedia Interface */ + csa = readl(&matrix->ebicsa); + csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA; + writel(csa, &matrix->ebicsa); + + /* Configure SMC CS3 for NAND/SmartMedia */ + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), + &smc->cs[3].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_DBW_8 | + AT91_SMC_MODE_TDF_CYCLE(2), + &smc->cs[3].mode); + + /* Configure RDY/BSY */ + at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); + + /* Enable NandFlash */ + at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); +} + +#ifdef CONFIG_MACB +static void stamp9G20_macb_hw_init(void) +{ + struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; + struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC; + unsigned long erstl; + + /* Enable the PHY Chip via PA26 on the Stamp 2 Adaptor */ + at91_set_gpio_output(AT91_PIN_PA26, 0); + + /* + * Disable pull-up on: + * RXDV (PA17) => PHY normal mode (not Test mode) + * ERX0 (PA14) => PHY ADDR0 + * ERX1 (PA15) => PHY ADDR1 + * ERX2 (PA25) => PHY ADDR2 + * ERX3 (PA26) => PHY ADDR3 + * ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0 + * + * PHY has internal pull-down + */ + writel(pin_to_mask(AT91_PIN_PA14) | + pin_to_mask(AT91_PIN_PA15) | + pin_to_mask(AT91_PIN_PA17) | + pin_to_mask(AT91_PIN_PA18) | + pin_to_mask(AT91_PIN_PA28), + &pioa->pudr); + + erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK; + + /* Need to reset PHY -> 500ms reset */ + writel(AT91_RSTC_KEY | (AT91_RSTC_MR_ERSTL(13) & + ~AT91_RSTC_MR_URSTEN), &rstc->mr); + writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr); + + /* Wait for end of hardware reset */ + unsigned long start = get_timer(0); + unsigned long timeout = 1000; /* 1000ms */ + + while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL)) { + + /* avoid shutdown by watchdog */ + WATCHDOG_RESET(); + mdelay(10); + + /* timeout for not getting stuck in an endless loop */ + if (get_timer(start) >= timeout) { + puts("*** ERROR: Timeout waiting for PHY reset!\n"); + break; + }; + }; + + /* Restore NRST value */ + writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN, + &rstc->mr); + + /* Re-enable pull-up */ + writel(pin_to_mask(AT91_PIN_PA14) | + pin_to_mask(AT91_PIN_PA15) | + pin_to_mask(AT91_PIN_PA17) | + pin_to_mask(AT91_PIN_PA18) | + pin_to_mask(AT91_PIN_PA28), + &pioa->puer); + + /* Initialize EMAC=MACB hardware */ + at91_macb_hw_init(); +} +#endif /* CONFIG_MACB */ + +int board_early_init_f(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + + /* Enable clocks for all PIOs */ + writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | + (1 << ATMEL_ID_PIOC), &pmc->pcer); + + return 0; +} + +int board_init(void) +{ + /* Adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + /* Enable the serial interface */ + at91_set_gpio_output(AT91_PIN_PC9, 1); + at91_seriald_hw_init(); + + stamp9G20_nand_hw_init(); +#ifdef CONFIG_MACB + stamp9G20_macb_hw_init(); +#endif + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size( + (void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; +} + +#ifdef CONFIG_MACB +int board_eth_init(bd_t *bis) +{ + return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00); +} +#endif /* CONFIG_MACB */ diff --git a/boards.cfg b/boards.cfg index 056f96ae3..52552e1d1 100644 --- a/boards.cfg +++ b/boards.cfg @@ -121,6 +121,8 @@ cpu9G20_nand_128M arm arm926ejs cpu9260 eukrea pm9261 arm arm926ejs pm9261 ronetix at91 pm9261:AT91SAM9261 pm9263 arm arm926ejs pm9263 ronetix at91 pm9263:AT91SAM9263 pm9g45 arm arm926ejs pm9g45 ronetix at91 pm9g45:AT91SAM9G45 +portuxg20 arm arm926ejs stamp9g20 taskit at91 stamp9g20:AT91SAM9G20,PORTUXG20 +stamp9g20 arm arm926ejs stamp9g20 taskit at91 stamp9g20:AT91SAM9G20 cam_enc_4xx arm arm926ejs cam_enc_4xx ait davinci cam_enc_4xx da830evm arm arm926ejs da8xxevm davinci davinci da850_am18xxevm arm arm926ejs da8xxevm davinci davinci da850evm:DA850_AM18X_EVM,MAC_ADDR_IN_EEPROM,SYS_I2C_EEPROM_ADDR_LEN=2,SYS_I2C_EEPROM_ADDR=0x50 diff --git a/include/configs/stamp9g20.h b/include/configs/stamp9g20.h new file mode 100644 index 000000000..a2a0156a6 --- /dev/null +++ b/include/configs/stamp9g20.h @@ -0,0 +1,266 @@ +/* + * (C) Copyright 2007-2008 + * Stelian Pop <stelian@popies.net> + * Lead Tech Design <www.leadtechdesign.com> + * + * (C) Copyright 2010 + * Achim Ehrlich <aehrlich@taskit.de> + * taskit GmbH <www.taskit.de> + * + * (C) Copyright 2012 + * Markus Hubig <mhubig@imko.de> + * IMKO GmbH <www.imko.de> + * + * Configuation settings for the stamp9g20 CPU module. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * SoC must be defined first, before hardware.h is included. + * In this case SoC is defined in boards.cfg. + */ +#include <asm/hardware.h> + +/* + * Warning: changing CONFIG_SYS_TEXT_BASE requires adapting the initial boot + * program. Since the linker has to swallow that define, we must use a pure + * hex number here! + */ +#define CONFIG_SYS_TEXT_BASE 0x23f00000 + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432MHz crystal */ +#define CONFIG_SYS_HZ 1000 /* 1ms resolution */ + +/* misc settings */ +#define CONFIG_CMDLINE_TAG /* pass commandline to Kernel */ +#define CONFIG_SETUP_MEMORY_TAGS /* pass memory defs to kernel */ +#define CONFIG_INITRD_TAG /* pass initrd param to kernel */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ +#define CONFIG_BOARD_EARLY_INIT_f /* call board_early_init_f() */ +#define CONFIG_DISPLAY_CPUINFO /* display CPU Info at startup */ + +/* setting board specific options */ +#ifdef CONFIG_PORTUXG20 +# define CONFIG_MACH_TYPE MACH_TYPE_PORTUXG20 +# define CONFIG_MACB +#else +# define CONFIG_MACH_TYPE MACH_TYPE_STAMP9G20 +#endif + +/* + * SDRAM: 1 bank, 64 MB, base address 0x20000000 + * Already initialized before u-boot gets started. + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 +#define CONFIG_SYS_SDRAM_SIZE (64 << 20) + +/* + * Perform a SDRAM Memtest from the start of SDRAM + * till the beginning of the U-Boot position in RAM. + */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - 0x100000) + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN \ + ROUND(3 * CONFIG_ENV_SIZE + (128 << 10), 0x1000) + +/* + * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, + * leaving the correct space for initial global data structure above that + * address while providing maximum stack area below. + */ +#define CONFIG_SYS_INIT_SP_ADDR \ + (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) + +/* NAND flash settings */ +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +#define CONFIG_SYS_NAND_DBW_8 +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 + +/* general purpose I/O */ +#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ +#define CONFIG_AT91_GPIO /* enable the GPIO features */ +#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 + +/* LED configuration */ +#define CONFIG_STATUS_LED +#define CONFIG_BOARD_SPECIFIC_LED + +/* The LED PINs */ +#define CONFIG_RED_LED AT91_PIN_PC5 +#define CONFIG_GREEN_LED AT91_PIN_PC4 +#define CONFIG_YELLOW_LED AT91_PIN_PC10 + +#define STATUS_LED_RED 0 +#define STATUS_LED_GREEN 1 +#define STATUS_LED_YELLOW 2 + +/* Red LED */ +#define STATUS_LED_BIT STATUS_LED_RED +#define STATUS_LED_STATE STATUS_LED_OFF +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) + +/* Green LED */ +#define STATUS_LED_BIT1 STATUS_LED_GREEN +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) + +/* Yellow LED */ +#define STATUS_LED_BIT2 STATUS_LED_YELLOW +#define STATUS_LED_STATE2 STATUS_LED_OFF +#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2) + +/* Boot status LED */ +#define STATUS_LED_BOOT STATUS_LED_GREEN + +/* + * Ethernet configuration + * + * PortuxG20 has always ethernet but for Stamp9G20 you + * can enable it here if your baseboard features ethernet. + */ + +/* #define CONFIG_MACB */ + +#ifdef CONFIG_MACB +# define CONFIG_RMII /* use reduced MII inteface */ +# define CONFIG_NET_RETRY_COUNT 20 /* # of DHCP/BOOTP retries */ + +/* BOOTP and DHCP options */ +# define CONFIG_BOOTP_BOOTFILESIZE +# define CONFIG_BOOTP_BOOTPATH +# define CONFIG_BOOTP_GATEWAY +# define CONFIG_BOOTP_HOSTNAME +# define CONFIG_NFSBOOTCOMMAND \ + "setenv autoload yes; setenv autoboot yes; " \ + "setenv bootargs ${basicargs} ${mtdparts} " \ + "root=/dev/nfs ip=dhcp nfsroot=${serverip}:/srv/nfs/rootfs; " \ + "dhcp" +#endif /* CONFIG_MACB */ + +/* Enable the watchdog */ +#define CONFIG_AT91SAM9_WATCHDOG +#define CONFIG_HW_WATCHDOG + +/* USB configuration */ +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 + +/* General Boot Parameter */ +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTCOMMAND "run flashboot" +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING + +/* + * RAM Memory address where to put the + * Linux Kernel befor starting. + */ +#define CONFIG_SYS_LOAD_ADDR 0x22000000 + +/* + * The NAND Flash partitions: + * ========================================== + * 0x0000000-0x001ffff -> 128k, bootstrap + * 0x0020000-0x005ffff -> 256k, u-boot + * 0x0060000-0x007ffff -> 128k, env1 + * 0x0080000-0x009ffff -> 128k, env2 (backup) + * 0x0100000-0x06fffff -> 6M, kernel + * 0x0700000-0x8000000 -> 121M, RootFS + */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET ((128 + 256) << 10) +#define CONFIG_ENV_OFFSET_REDUND ((128 + 256 + 128) << 10) +#define CONFIG_ENV_SIZE (128 << 10) + +/* + * Predefined environment variables. + * Usefull to define some easy to use boot commands. + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + \ + "basicargs=console=ttyS0,115200\0" \ + \ + "mtdparts=mtdparts=atmel_nand:128k(bootstrap)ro," \ + "256k(uboot)ro,128k(env1)ro," \ + "128k(env2)ro,6M(linux),-(root)rw\0" \ + \ + "flashboot=setenv bootargs ${basicargs} ${mtdparts} " \ + "root=/dev/mtdblock5 rootfstype=jffs2; " \ + "nand read 0x22000000 0x100000 0x600000; " \ + "bootm 22000000\0" \ + \ + "sdboot=setenv bootargs ${basicargs} ${mtdparts} " \ + "root=/dev/mmcblk0p1 rootwait; " \ + "nand read 0x22000000 0x100000 0x600000; " \ + "bootm 22000000" + +/* Command line & features configuration */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_LOADS + +#define CONFIG_CMD_NAND +#define CONFIG_CMD_USB +#define CONFIG_CMD_FAT +#define CONFIG_CMD_LED + +#ifdef CONFIG_MACB +# define CONFIG_CMD_PING +# define CONFIG_CMD_DHCP +#else +# undef CONFIG_CMD_BOOTD +# undef CONFIG_CMD_NET +# undef CONFIG_CMD_NFS +#endif /* CONFIG_MACB */ + +#endif /* __CONFIG_H */ |