ppc4xx: Remove ML2 board support

As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Marek Vasut <marex@denx.de>

1 files changed, 0 insertions, 257 deletions

diff --git a/include/configs/ML2.h b/include/configs/ML2.h
deleted file mode 100644
index 4df9f4cbc..000000000
--- a/include/configs/ML2.h
+++ /dev/null
@@ -1,257 +0,0 @@
-/*
- * ML2.h: ML2 specific config options
- *
- * Copyright 2002 Mind NV
- *
- * http://www.mind.be/
- *
- * Author : Peter De Schrijver (p2@mind.be)
- *
- * Derived from : other configuration header files in this tree
- *
- * This software may be used and distributed according to the terms of
- * the GNU General Public License (GPL) version 2, incorporated herein by
- * reference. Drivers based on or derived from this code fall under the GPL
- * and must retain the authorship, copyright and this license notice. This
- * file is not a complete program and may only be used when the entire
- * program is licensed under the GPL.
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_ML2	1	/* ...on a ML2 board	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x18000000
-#define CONFIG_SYS_LDSCRIPT	"board/ml2/u-boot.lds"
-
-#define CONFIG_ENV_IS_IN_FLASH     1
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#undef CONFIG_ENV_IS_IN_FLASH
-#else
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_IN_NVRAM
-#endif
-#endif
-
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
-
-#if 1
-#define CONFIG_BOOTCOMMAND	"bootm" /* autoboot command	*/
-#else
-#define CONFIG_BOOTCOMMAND	"bootp" /* autoboot command		*/
-#endif
-
-#define CONFIG_PREBOOT		"fsload 0x00100000 /boot/image"
-
-#if 0
-#define CONFIG_BOOTARGS		"root=/dev/nfs "                        \
-    "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 "        \
-    "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
-#else
-#define CONFIG_BOOTARGS		"root=/dev/mtdblock2 "			\
-   "console=ttyS0 console=tty"
-
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_KGDB
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_JFFS2
-
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_RTC
-#undef CONFIG_CMD_PCI
-#undef CONFIG_CMD_I2C
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_SYS_CLK_FREQ 50000000
-
-#define CONFIG_SPD_EEPROM      1       /* use SPD EEPROM for setup    */
-
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SLAVE	0x7F
-#define CONFIG_SYS_I2C_SPEED	400000
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- *    baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- */
-#undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* external serial clock */
-#undef  CONFIG_SYS_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
-
-#define CONFIG_SYS_BASE_BAUD       (3125000*16)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_BASE_BAUD
-#define CONFIG_SYS_DUART_CHAN		0
-#define CONFIG_SYS_NS16550_COM1	0xa0001003
-#define CONFIG_SYS_NS16550_COM2	0xa0011003
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550 1
-#define CONFIG_SYS_INIT_CHAN1	 1
-#define CONFIG_SYS_INIT_CHAN2	 1
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/
-
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x18000000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 196 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/* BEG ENVIRONNEMENT FLASH */
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET		0x00050000 /* Offset of Environment Sector  */
-#define	CONFIG_ENV_SIZE		0x10000	/* Total Size of Environment Sector	*/
-#define CONFIG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
-#endif
-/* END ENVIRONNEMENT FLASH */
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xf0000000	/* NVRAM base address	*/
-#define CONFIG_SYS_NVRAM_SIZE		0x1ff8		/* NVRAM size	*/
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_SIZE		0x1000		/* Size of Environment vars	*/
-#define CONFIG_ENV_ADDR		\
-	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)	/* Env	*/
-#endif
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/
-
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR	0xF0000500
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-#define CONFIG_SYS_INIT_RAM_ADDR       0x800000  /* inside of SDRAM                     */
-#define CONFIG_SYS_INIT_RAM_SIZE        0x2000  /* Size of used area in RAM             */
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS      0x50
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00080000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT		"nor0=ml2-0"
-#define MTDPARTS_DEFAULT	"mtdparts=ml2-0:-@512k(jffs2)"
-*/
-
-#endif	/* __CONFIG_H */