aboutsummaryrefslogtreecommitdiff
path: root/arch
diff options
context:
space:
mode:
authorPeter Korsgaard <peter.korsgaard@barco.com>2012-10-18 01:21:09 +0000
committerTom Rini <trini@ti.com>2012-10-25 11:31:36 -0700
commite363426e999b786ee4791f49d90ae84a3210f7b8 (patch)
tree31e9706c53d440ded06ae037a8da0babd8111a89 /arch
parentc50cce275866b4b0e36e1102041d7ee7aa24ee28 (diff)
downloadu-boot-linaro-stable-e363426e999b786ee4791f49d90ae84a3210f7b8.tar.gz
am33xx: move ti i2c baseboard header handling to board/ti/am335x/
The i2c header is specific to ti(-derived) boards, and not generic for all am335x boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make re-apply with rtc32k_enable() applied] Signed-off-by: Tom Rini <trini@ti.com>
Diffstat (limited to 'arch')
-rw-r--r--arch/arm/cpu/armv7/am33xx/board.c261
-rw-r--r--arch/arm/include/asm/arch-am33xx/sys_proto.h27
2 files changed, 0 insertions, 288 deletions
diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c
index 0b8b76d1f..8280b3550 100644
--- a/arch/arm/cpu/armv7/am33xx/board.c
+++ b/arch/arm/cpu/armv7/am33xx/board.c
@@ -36,11 +36,6 @@
DECLARE_GLOBAL_DATA_PTR;
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-#ifdef CONFIG_SPL_BUILD
-static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
-#endif
-
static const struct gpio_bank gpio_bank_am33xx[4] = {
{ (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
@@ -50,172 +45,6 @@ static const struct gpio_bank gpio_bank_am33xx[4] = {
const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx;
-/* MII mode defines */
-#define MII_MODE_ENABLE 0x0
-#define RGMII_MODE_ENABLE 0xA
-
-/* GPIO that controls power to DDR on EVM-SK */
-#define GPIO_DDR_VTT_EN 7
-
-static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-
-static struct am335x_baseboard_id __attribute__((section (".data"))) header;
-
-static inline int board_is_bone(void)
-{
- return !strncmp(header.name, "A335BONE", HDR_NAME_LEN);
-}
-
-static inline int board_is_bone_lt(void)
-{
- return !strncmp(header.name, "A335BNLT", HDR_NAME_LEN);
-}
-
-static inline int board_is_evm_sk(void)
-{
- return !strncmp("A335X_SK", header.name, HDR_NAME_LEN);
-}
-
-/*
- * Read header information from EEPROM into global structure.
- */
-static int read_eeprom(void)
-{
- /* Check if baseboard eeprom is available */
- if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {
- puts("Could not probe the EEPROM; something fundamentally "
- "wrong on the I2C bus.\n");
- return -ENODEV;
- }
-
- /* read the eeprom using i2c */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)&header,
- sizeof(header))) {
- puts("Could not read the EEPROM; something fundamentally"
- " wrong on the I2C bus.\n");
- return -EIO;
- }
-
- if (header.magic != 0xEE3355AA) {
- /*
- * read the eeprom using i2c again,
- * but use only a 1 byte address
- */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1,
- (uchar *)&header, sizeof(header))) {
- puts("Could not read the EEPROM; something "
- "fundamentally wrong on the I2C bus.\n");
- return -EIO;
- }
-
- if (header.magic != 0xEE3355AA) {
- printf("Incorrect magic number (0x%x) in EEPROM\n",
- header.magic);
- return -EINVAL;
- }
- }
-
- return 0;
-}
-
-#ifdef CONFIG_SPL_BUILD
-/* UART Defines */
-#define UART_RESET (0x1 << 1)
-#define UART_CLK_RUNNING_MASK 0x1
-#define UART_SMART_IDLE_EN (0x1 << 0x3)
-
-static void rtc32k_enable(void)
-{
- struct rtc_regs *rtc = (struct rtc_regs *)AM335X_RTC_BASE;
-
- /*
- * Unlock the RTC's registers. For more details please see the
- * RTC_SS section of the TRM. In order to unlock we need to
- * write these specific values (keys) in this order.
- */
- writel(0x83e70b13, &rtc->kick0r);
- writel(0x95a4f1e0, &rtc->kick1r);
-
- /* Enable the RTC 32K OSC by setting bits 3 and 6. */
- writel((1 << 3) | (1 << 6), &rtc->osc);
-}
-#endif
-
-/*
- * Determine what type of DDR we have.
- */
-static short inline board_memory_type(void)
-{
- /* The following boards are known to use DDR3. */
- if (board_is_evm_sk() || board_is_bone_lt())
- return EMIF_REG_SDRAM_TYPE_DDR3;
-
- return EMIF_REG_SDRAM_TYPE_DDR2;
-}
-
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
-{
- /* WDT1 is already running when the bootloader gets control
- * Disable it to avoid "random" resets
- */
- writel(0xAAAA, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
- writel(0x5555, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
-
-#ifdef CONFIG_SPL_BUILD
- /* Setup the PLLs and the clocks for the peripherals */
- pll_init();
-
- /* Enable RTC32K clock */
- rtc32k_enable();
-
- /* UART softreset */
- u32 regVal;
-
- enable_uart0_pin_mux();
-
- regVal = readl(&uart_base->uartsyscfg);
- regVal |= UART_RESET;
- writel(regVal, &uart_base->uartsyscfg);
- while ((readl(&uart_base->uartsyssts) &
- UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
- ;
-
- /* Disable smart idle */
- regVal = readl(&uart_base->uartsyscfg);
- regVal |= UART_SMART_IDLE_EN;
- writel(regVal, &uart_base->uartsyscfg);
-
- gd = &gdata;
-
- preloader_console_init();
-
- /* Initalize the board header */
- enable_i2c0_pin_mux();
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- if (read_eeprom() < 0)
- puts("Could not get board ID.\n");
-
- enable_board_pin_mux(&header);
- if (board_is_evm_sk()) {
- /*
- * EVM SK 1.2A and later use gpio0_7 to enable DDR3.
- * This is safe enough to do on older revs.
- */
- gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
- gpio_direction_output(GPIO_DDR_VTT_EN, 1);
- }
-
- config_ddr(board_memory_type());
-#endif
-}
-
#if defined(CONFIG_OMAP_HSMMC) && !defined(CONFIG_SPL_BUILD)
int board_mmc_init(bd_t *bis)
{
@@ -234,93 +63,3 @@ void setup_clocks_for_console(void)
/* Not yet implemented */
return;
}
-
-/*
- * Basic board specific setup. Pinmux has been handled already.
- */
-int board_init(void)
-{
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- if (read_eeprom() < 0)
- puts("Could not get board ID.\n");
-
- gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
-
- return 0;
-}
-
-#ifdef CONFIG_DRIVER_TI_CPSW
-static void cpsw_control(int enabled)
-{
- /* VTP can be added here */
-
- return;
-}
-
-static struct cpsw_slave_data cpsw_slaves[] = {
- {
- .slave_reg_ofs = 0x208,
- .sliver_reg_ofs = 0xd80,
- .phy_id = 0,
- },
- {
- .slave_reg_ofs = 0x308,
- .sliver_reg_ofs = 0xdc0,
- .phy_id = 1,
- },
-};
-
-static struct cpsw_platform_data cpsw_data = {
- .mdio_base = AM335X_CPSW_MDIO_BASE,
- .cpsw_base = AM335X_CPSW_BASE,
- .mdio_div = 0xff,
- .channels = 8,
- .cpdma_reg_ofs = 0x800,
- .slaves = 1,
- .slave_data = cpsw_slaves,
- .ale_reg_ofs = 0xd00,
- .ale_entries = 1024,
- .host_port_reg_ofs = 0x108,
- .hw_stats_reg_ofs = 0x900,
- .mac_control = (1 << 5),
- .control = cpsw_control,
- .host_port_num = 0,
- .version = CPSW_CTRL_VERSION_2,
-};
-
-int board_eth_init(bd_t *bis)
-{
- uint8_t mac_addr[6];
- uint32_t mac_hi, mac_lo;
-
- if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
- debug("<ethaddr> not set. Reading from E-fuse\n");
- /* try reading mac address from efuse */
- mac_lo = readl(&cdev->macid0l);
- mac_hi = readl(&cdev->macid0h);
- mac_addr[0] = mac_hi & 0xFF;
- mac_addr[1] = (mac_hi & 0xFF00) >> 8;
- mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
- mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
- mac_addr[4] = mac_lo & 0xFF;
- mac_addr[5] = (mac_lo & 0xFF00) >> 8;
-
- if (is_valid_ether_addr(mac_addr))
- eth_setenv_enetaddr("ethaddr", mac_addr);
- else
- return -1;
- }
-
- if (board_is_bone() || board_is_bone_lt()) {
- writel(MII_MODE_ENABLE, &cdev->miisel);
- cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
- PHY_INTERFACE_MODE_MII;
- } else {
- writel(RGMII_MODE_ENABLE, &cdev->miisel);
- cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
- PHY_INTERFACE_MODE_RGMII;
- }
-
- return cpsw_register(&cpsw_data);
-}
-#endif
diff --git a/arch/arm/include/asm/arch-am33xx/sys_proto.h b/arch/arm/include/asm/arch-am33xx/sys_proto.h
index 819ea650f..9cf35e025 100644
--- a/arch/arm/include/asm/arch-am33xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-am33xx/sys_proto.h
@@ -19,24 +19,6 @@
#ifndef _SYS_PROTO_H_
#define _SYS_PROTO_H_
-/*
- * AM335x parts define a system EEPROM that defines certain sub-fields.
- * We use these fields to in turn see what board we are on, and what
- * that might require us to set or not set.
- */
-#define HDR_NO_OF_MAC_ADDR 3
-#define HDR_ETH_ALEN 6
-#define HDR_NAME_LEN 8
-
-struct am335x_baseboard_id {
- unsigned int magic;
- char name[HDR_NAME_LEN];
- char version[4];
- char serial[12];
- char config[32];
- char mac_addr[HDR_NO_OF_MAC_ADDR][HDR_ETH_ALEN];
-};
-
#define BOARD_REV_ID 0x0
u32 get_cpu_rev(void);
@@ -51,13 +33,4 @@ u32 get_device_type(void);
void setup_clocks_for_console(void);
void ddr_pll_config(unsigned int ddrpll_M);
-/*
- * We have three pin mux functions that must exist. We must be able to enable
- * uart0, for initial output and i2c0 to read the main EEPROM. We then have a
- * main pinmux function that can be overridden to enable all other pinmux that
- * is required on the board.
- */
-void enable_uart0_pin_mux(void);
-void enable_i2c0_pin_mux(void);
-void enable_board_pin_mux(struct am335x_baseboard_id *header);
#endif