powerpc/85xx: Add P5040 processor support

Add support for the Freescale P5040 SOC, which is similar to the P5020.
Features of the P5040 are:

Four P5040 single-threaded e5500 cores built
    Up to 2.4 GHz with 64-bit ISA support
    Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
    2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
        support Up to 1600MT/s
    Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
    Packet parsing, classification, and distribution (FMAN)
    Queue management for scheduling, packet sequencing and
    congestion management (QMAN)
    Hardware buffer management for buffer allocation and
    de-allocation (BMAN)
    Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes
    20 lanes at up to 5 Gbps
    Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
    Two 10 Gbps Ethernet MACs
    Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
    Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
    Two serial ATA (SATA 2.0) controllers
    Two high-speed USB 2.0 controllers with integrated PHY
    Enhanced secure digital host controller (SD/MMC/eMMC)
    Enhanced serial peripheral interface (eSPI)
    Two I2C controllers
    Four UARTs
    Integrated flash controller supporting NAND and NOR flash
DMA
    Dual four channel
Support for hardware virtualization and partitioning enforcement
    Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
    Secure boot, secure debug, tamper detection, volatile key storage

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

7 files changed, 326 insertions, 0 deletions

diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile
index 33e93c88d..aad50f34a 100644
--- a/arch/powerpc/cpu/mpc85xx/Makefile
+++ b/arch/powerpc/cpu/mpc85xx/Makefile
@@ -66,6 +66,7 @@ COBJS-$(CONFIG_PPC_P2041)	+= ddr-gen3.o
 COBJS-$(CONFIG_PPC_P3041)	+= ddr-gen3.o
 COBJS-$(CONFIG_PPC_P4080)	+= ddr-gen3.o
 COBJS-$(CONFIG_PPC_P5020)	+= ddr-gen3.o
+COBJS-$(CONFIG_PPC_P5040)	+= ddr-gen3.o
 COBJS-$(CONFIG_BSC9131)		+= ddr-gen3.o
 
 COBJS-$(CONFIG_CPM2)	+= ether_fcc.o
@@ -80,6 +81,7 @@ COBJS-$(CONFIG_PPC_P2041) += p2041_ids.o
 COBJS-$(CONFIG_PPC_P3041) += p3041_ids.o
 COBJS-$(CONFIG_PPC_P4080) += p4080_ids.o
 COBJS-$(CONFIG_PPC_P5020) += p5020_ids.o
+COBJS-$(CONFIG_PPC_P5040) += p5040_ids.o
 
 COBJS-$(CONFIG_QE)	+= qe_io.o
 COBJS-$(CONFIG_CPM2)	+= serial_scc.o
@@ -110,6 +112,7 @@ COBJS-$(CONFIG_PPC_P2041) += p2041_serdes.o
 COBJS-$(CONFIG_PPC_P3041) += p3041_serdes.o
 COBJS-$(CONFIG_PPC_P4080) += p4080_serdes.o
 COBJS-$(CONFIG_PPC_P5020) += p5020_serdes.o
+COBJS-$(CONFIG_PPC_P5040) += p5040_serdes.o
 
 COBJS	= $(COBJS-y)
 COBJS	+= cpu.o
diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c
index 2a6806036..e6b1b1b7e 100644
--- a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c
+++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c
@@ -92,10 +92,17 @@ static const struct {
 	{ 17, 163, FSL_SRDS_BANK_2 },
 	{ 18, 164, FSL_SRDS_BANK_2 },
 	{ 19, 165, FSL_SRDS_BANK_2 },
+#ifdef CONFIG_PPC_P4080
 	{ 20, 170, FSL_SRDS_BANK_3 },
 	{ 21, 171, FSL_SRDS_BANK_3 },
 	{ 22, 172, FSL_SRDS_BANK_3 },
 	{ 23, 173, FSL_SRDS_BANK_3 },
+#else
+	{ 20, 166, FSL_SRDS_BANK_3 },
+	{ 21, 167, FSL_SRDS_BANK_3 },
+	{ 22, 168, FSL_SRDS_BANK_3 },
+	{ 23, 169, FSL_SRDS_BANK_3 },
+#endif
 };
 
 int serdes_get_lane_idx(int lane)
@@ -493,6 +500,9 @@ void fsl_serdes_init(void)
 	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
 	int cfg;
 	serdes_corenet_t *srds_regs;
+#ifdef CONFIG_PPC_P5040
+	serdes_corenet_t *srds2_regs;
+#endif
 	int lane, bank, idx;
 	int have_bank[SRDS_MAX_BANK] = {};
 #ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8
@@ -574,6 +584,34 @@ void fsl_serdes_init(void)
 		}
 	}
 
+#ifdef CONFIG_PPC_P5040
+	/*
+	 * Lanes on bank 4 on P5040 are commented-out, but for some SERDES
+	 * protocols, these lanes are routed to SATA.  We use serdes_prtcl_map
+	 * to decide whether a protocol is supported on a given lane, so SATA
+	 * will be identified as not supported, and therefore not initialized.
+	 * So for protocols which use SATA on bank4, we add SATA support in
+	 * serdes_prtcl_map.
+	 */
+	switch (cfg) {
+	case 0x0:
+	case 0x1:
+	case 0x2:
+	case 0x3:
+	case 0x4:
+	case 0x5:
+	case 0x6:
+	case 0x7:
+		serdes_prtcl_map |= 1 << SATA1 | 1 << SATA2;
+		break;
+	default:
+		srds2_regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES2_ADDR;
+
+		/* We don't need bank 4, so power it down */
+		setbits_be32(&srds2_regs->bank[0].rstctl, SRDS_RSTCTL_SDPD);
+	}
+#endif
+
 	soc_serdes_init();
 
 #ifdef CONFIG_SYS_P4080_ERRATUM_SERDES8
@@ -617,6 +655,38 @@ void fsl_serdes_init(void)
 		}
 	}
 
+#ifdef CONFIG_SYS_FSL_ERRATUM_A004699
+	/*
+	 * To avoid the situation that resulted in the P4080 erratum
+	 * SERDES-8, a given SerDes bank will use the PLLs from the previous
+	 * bank if one of the PLL frequencies is a multiple of the other.  For
+	 * instance, if bank 3 is running at 2.5GHz and bank 2 is at 1.25GHz,
+	 * then bank 3 will use bank 2's PLL.  P5040 Erratum A-004699 says
+	 * that, in this situation, lane synchronization is not initiated.  So
+	 * when we detect a bank with a "borrowed" PLL, we have to manually
+	 * initiate lane synchronization.
+	 */
+	for (bank = FSL_SRDS_BANK_2; bank <= FSL_SRDS_BANK_3; bank++) {
+		/* Determine the first lane for this bank */
+		unsigned int lane;
+
+		for (lane = 0; lane < SRDS_MAX_LANES; lane++)
+			if (lanes[lane].bank == bank)
+				break;
+		idx = lanes[lane].idx;
+
+		/*
+		 * Check if the PLL for the bank is borrowed.  The UOTHL
+		 * bit of the first lane will tell us that.
+		 */
+		if (in_be32(&srds_regs->lane[idx].gcr0) & SRDS_GCR0_UOTHL) {
+			/* Manually start lane synchronization */
+			setbits_be32(&srds_regs->bank[bank].pllcr0,
+				     SRDS_PLLCR0_PVCOCNT_EN);
+		}
+	}
+#endif
+
 #if defined(CONFIG_SYS_P4080_ERRATUM_SERDES8) || defined (CONFIG_SYS_P4080_ERRATUM_SERDES9)
 	for (lane = 0; lane < SRDS_MAX_LANES; lane++) {
 		enum srds_prtcl lane_prtcl;
diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.h b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.h
index f261351c8..c82060dd3 100644
--- a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.h
+++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.h
@@ -22,6 +22,11 @@
 #ifndef __FSL_CORENET_SERDES_H
 #define __FSL_CORENET_SERDES_H
 
+/*
+ * Note: For P5040, the fourth SerDes bank is on SerDes2, but U-boot currently
+ * only supports one SerDes controller.  For now, pretend that we have three
+ * banks and 18 lanes on the P5040.
+ */
 #define SRDS_MAX_LANES		18
 #define SRDS_MAX_BANK		3
 
diff --git a/arch/powerpc/cpu/mpc85xx/p5040_ids.c b/arch/powerpc/cpu/mpc85xx/p5040_ids.c
new file mode 100644
index 000000000..878ee3e73
--- /dev/null
+++ b/arch/powerpc/cpu/mpc85xx/p5040_ids.c
@@ -0,0 +1,127 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+
+#ifdef CONFIG_SYS_DPAA_QBMAN
+struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = {
+	/* dqrr liodn, frame data liodn, liodn off, sdest */
+	SET_QP_INFO(1, 2, 1, 0),
+	SET_QP_INFO(3, 4, 2, 1),
+	SET_QP_INFO(5, 6, 3, 2),
+	SET_QP_INFO(7, 8, 4, 3),
+	SET_QP_INFO(9, 10, 5, 0),
+	SET_QP_INFO(11, 12, 6, 1),
+	SET_QP_INFO(13, 14, 7, 2),
+	SET_QP_INFO(15, 16, 8, 3),
+	SET_QP_INFO(17, 18, 9, 0),	/* for now, set sdest to 0 */
+	SET_QP_INFO(19, 20, 10, 0),	/* for now, set sdest to 0 */
+};
+#endif
+
+struct liodn_id_table liodn_tbl[] = {
+#ifdef CONFIG_SYS_DPAA_QBMAN
+	SET_QMAN_LIODN(31),
+	SET_BMAN_LIODN(32),
+#endif
+
+	SET_SDHC_LIODN(1, 64),
+
+	SET_USB_LIODN(1, "fsl-usb2-mph", 93),
+	SET_USB_LIODN(2, "fsl-usb2-dr", 94),
+
+	SET_SATA_LIODN(1, 95),
+	SET_SATA_LIODN(2, 96),
+
+	SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 195),
+	SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 196),
+	SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 197),
+
+	SET_DMA_LIODN(1, 193),
+	SET_DMA_LIODN(2, 194),
+};
+int liodn_tbl_sz = ARRAY_SIZE(liodn_tbl);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+struct liodn_id_table fman1_liodn_tbl[] = {
+	SET_FMAN_RX_1G_LIODN(1, 0, 6),
+	SET_FMAN_RX_1G_LIODN(1, 1, 7),
+	SET_FMAN_RX_1G_LIODN(1, 2, 8),
+	SET_FMAN_RX_1G_LIODN(1, 3, 9),
+	SET_FMAN_RX_1G_LIODN(1, 4, 10),
+	SET_FMAN_RX_10G_LIODN(1, 0, 11),
+};
+int fman1_liodn_tbl_sz = ARRAY_SIZE(fman1_liodn_tbl);
+
+#if (CONFIG_SYS_NUM_FMAN == 2)
+struct liodn_id_table fman2_liodn_tbl[] = {
+	SET_FMAN_RX_1G_LIODN(2, 0, 12),
+	SET_FMAN_RX_1G_LIODN(2, 1, 13),
+	SET_FMAN_RX_1G_LIODN(2, 2, 14),
+	SET_FMAN_RX_1G_LIODN(2, 3, 15),
+	SET_FMAN_RX_1G_LIODN(2, 4, 16),
+	SET_FMAN_RX_10G_LIODN(2, 0, 17),
+};
+int fman2_liodn_tbl_sz = ARRAY_SIZE(fman2_liodn_tbl);
+#endif
+#endif
+
+struct liodn_id_table sec_liodn_tbl[] = {
+	SET_SEC_JR_LIODN_ENTRY(0, 129, 130),
+	SET_SEC_JR_LIODN_ENTRY(1, 131, 132),
+	SET_SEC_JR_LIODN_ENTRY(2, 133, 134),
+	SET_SEC_JR_LIODN_ENTRY(3, 135, 136),
+	SET_SEC_RTIC_LIODN_ENTRY(a, 89),
+	SET_SEC_RTIC_LIODN_ENTRY(b, 90),
+	SET_SEC_RTIC_LIODN_ENTRY(c, 91),
+	SET_SEC_RTIC_LIODN_ENTRY(d, 92),
+	SET_SEC_DECO_LIODN_ENTRY(0, 139, 140),
+	SET_SEC_DECO_LIODN_ENTRY(1, 141, 142),
+	SET_SEC_DECO_LIODN_ENTRY(2, 143, 144),
+	SET_SEC_DECO_LIODN_ENTRY(3, 145, 146),
+};
+int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl);
+
+#ifdef CONFIG_SYS_FSL_RAID_ENGINE
+struct liodn_id_table raide_liodn_tbl[] = {
+	SET_RAID_ENGINE_JQ_LIODN_ENTRY(0, 0, 60),
+	SET_RAID_ENGINE_JQ_LIODN_ENTRY(0, 1, 61),
+	SET_RAID_ENGINE_JQ_LIODN_ENTRY(1, 0, 62),
+	SET_RAID_ENGINE_JQ_LIODN_ENTRY(1, 1, 63),
+};
+int raide_liodn_tbl_sz = ARRAY_SIZE(raide_liodn_tbl);
+#endif
+
+struct liodn_id_table liodn_bases[] = {
+	[FSL_HW_PORTAL_SEC]  = SET_LIODN_BASE_2(64, 101),
+#ifdef CONFIG_SYS_DPAA_FMAN
+	[FSL_HW_PORTAL_FMAN1] = SET_LIODN_BASE_1(32),
+#endif
+#if (CONFIG_SYS_NUM_FMAN == 2)
+	[FSL_HW_PORTAL_FMAN2] = SET_LIODN_BASE_1(160),
+#endif
+#ifdef CONFIG_SYS_FSL_RAID_ENGINE
+	[FSL_HW_PORTAL_RAID_ENGINE]  = SET_LIODN_BASE_1(49),
+#endif
+};
diff --git a/arch/powerpc/cpu/mpc85xx/p5040_serdes.c b/arch/powerpc/cpu/mpc85xx/p5040_serdes.c
new file mode 100644
index 000000000..890b88e4e
--- /dev/null
+++ b/arch/powerpc/cpu/mpc85xx/p5040_serdes.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_serdes.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include "fsl_corenet_serdes.h"
+
+/*
+ * Note: For P5040, the fourth SerDes bank (with two lanes) is on SerDes2, but
+ * U-boot only supports one SerDes controller.  Therefore, we ignore bank 4 in
+ * this table.  This works because most of the SerDes code is for errata
+ * work-arounds, and there are no P5040 errata that effect bank 4.
+ */
+
+static u8 serdes_cfg_tbl[][SRDS_MAX_LANES] = {
+	[0x00] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE2, PCIE2,
+		SGMII_FM2_DTSEC3, SGMII_FM2_DTSEC4, SGMII_FM1_DTSEC1,
+		SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
+		XAUI_FM2, XAUI_FM2, XAUI_FM2, XAUI_FM2, /* SATA1, SATA2, */ },
+	[0x01] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE2, PCIE2,
+		SGMII_FM1_DTSEC3, SGMII_FM2_DTSEC4, XAUI_FM1, XAUI_FM1,
+		XAUI_FM1, XAUI_FM1, XAUI_FM2, XAUI_FM2, XAUI_FM2,
+		XAUI_FM2, /* SATA1, SATA2 */ },
+	[0x02] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, SGMII_FM1_DTSEC3,
+		SGMII_FM1_DTSEC4, SGMII_FM2_DTSEC3, SGMII_FM2_DTSEC4,
+		XAUI_FM1, XAUI_FM1, XAUI_FM1, XAUI_FM1, XAUI_FM2, XAUI_FM2,
+		XAUI_FM2, XAUI_FM2, /* SATA1, SATA2 */ },
+	[0x03] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, SGMII_FM2_DTSEC1,
+		SGMII_FM2_DTSEC2, SGMII_FM2_DTSEC3, SGMII_FM2_DTSEC4,
+		SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3,
+		SGMII_FM1_DTSEC4, XAUI_FM2, XAUI_FM2, XAUI_FM2, XAUI_FM2,
+		/* SATA1, SATA2 */ },
+	[0x04] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE3, SGMII_FM2_DTSEC1,
+		SGMII_FM2_DTSEC2, SGMII_FM2_DTSEC3, SGMII_FM2_DTSEC4,
+		SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3,
+		SGMII_FM1_DTSEC4, XAUI_FM2, XAUI_FM2, XAUI_FM2, XAUI_FM2,
+		/* SATA1, SATA2 */ },
+	[0x05] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE3, SGMII_FM1_DTSEC3,
+		SGMII_FM1_DTSEC4, SGMII_FM2_DTSEC3, SGMII_FM2_DTSEC4,
+		XAUI_FM1, XAUI_FM1, XAUI_FM1, XAUI_FM1, XAUI_FM2, XAUI_FM2,
+		XAUI_FM2, XAUI_FM2, /* SATA1, SATA2 */ },
+	[0x06] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1,
+		SGMII_FM2_DTSEC3, SGMII_FM2_DTSEC4, SGMII_FM1_DTSEC1,
+		SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
+		XAUI_FM2, XAUI_FM2, XAUI_FM2, XAUI_FM2, /* SATA1, SATA2 */ },
+	[0x07] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1,
+		SGMII_FM1_DTSEC3, SGMII_FM2_DTSEC4, XAUI_FM1, XAUI_FM1,
+		XAUI_FM1, XAUI_FM1, XAUI_FM2, XAUI_FM2, XAUI_FM2,
+		XAUI_FM2, /* SATA1, SATA2 */ },
+	[0x11] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE2, PCIE2,
+		AURORA, AURORA, SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+		SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, NONE, NONE, SATA1, SATA2,
+		/* NONE, NONE */ },
+	[0x15] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE2, PCIE2,
+		AURORA, AURORA, XAUI_FM1, XAUI_FM1, XAUI_FM1, XAUI_FM1,
+		NONE, NONE, SATA1, SATA2, /* NONE, NONE */ },
+	[0x2a] = {PCIE1, PCIE1, PCIE3, PCIE3, PCIE2, PCIE2, PCIE2, PCIE2,
+		AURORA, AURORA, SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+		SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, XAUI_FM2, XAUI_FM2,
+		XAUI_FM2, XAUI_FM2, /* NONE, NONE */ },
+	[0x34] = {PCIE1, PCIE1, PCIE1, PCIE1, SGMII_FM1_DTSEC1,
+		SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, AURORA,
+		AURORA, XAUI_FM1, XAUI_FM1, XAUI_FM1, XAUI_FM1, NONE,
+		NONE, SATA1, SATA2, /* NONE, NONE */ },
+	[0x35] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2,
+		SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, AURORA, AURORA, XAUI_FM1,
+		XAUI_FM1, XAUI_FM1, XAUI_FM1, NONE, NONE, SATA1, SATA2,
+		/* NONE, NONE */ },
+	[0x36] = {PCIE1, PCIE1, PCIE3, PCIE3, SGMII_FM1_DTSEC1,
+		SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, AURORA,
+		AURORA, XAUI_FM1, XAUI_FM1, XAUI_FM1, XAUI_FM1, NONE,
+		NONE, SATA1, SATA2, /* NONE, NONE */ },
+};
+
+enum srds_prtcl serdes_get_prtcl(int cfg, int lane)
+{
+	if (!serdes_lane_enabled(lane))
+		return NONE;
+
+	return serdes_cfg_tbl[cfg][lane];
+}
+
+int is_serdes_prtcl_valid(u32 prtcl)
+{
+	int i;
+
+	if (prtcl > ARRAY_SIZE(serdes_cfg_tbl))
+		return 0;
+
+	for (i = 0; i < SRDS_MAX_LANES; i++) {
+		if (serdes_cfg_tbl[prtcl][i] != NONE)
+			return 1;
+	}
+
+	return 0;
+}
diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c
index abfeb268d..6dd9e8db7 100644
--- a/arch/powerpc/cpu/mpc85xx/speed.c
+++ b/arch/powerpc/cpu/mpc85xx/speed.c
@@ -112,6 +112,8 @@ void get_sys_info (sys_info_t * sysInfo)
 #define HWA_ASYNC_DIV	0x04000000
 #if (CONFIG_SYS_FSL_NUM_CC_PLLS == 2)
 #define HWA_CC_PLL	1
+#elif (CONFIG_SYS_FSL_NUM_CC_PLLS == 3)
+#define HWA_CC_PLL	2
 #elif (CONFIG_SYS_FSL_NUM_CC_PLLS == 4)
 #define HWA_CC_PLL	2
 #else
diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c
index 78a8f926b..fb7878434 100644
--- a/arch/powerpc/cpu/mpc8xxx/cpu.c
+++ b/arch/powerpc/cpu/mpc8xxx/cpu.c
@@ -73,6 +73,8 @@ struct cpu_type cpu_type_list [] = {
 	CPU_TYPE_ENTRY(P4080, P4080, 8),
 	CPU_TYPE_ENTRY(P5010, P5010, 1),
 	CPU_TYPE_ENTRY(P5020, P5020, 2),
+	CPU_TYPE_ENTRY(P5021, P5021, 2),
+	CPU_TYPE_ENTRY(P5040, P5040, 4),
 	CPU_TYPE_ENTRY(BSC9130, 9130, 1),
 	CPU_TYPE_ENTRY(BSC9131, 9131, 1),
 #elif defined(CONFIG_MPC86xx)