Add support for VirtLab2 board

(needed because of differences in the PCMCIA hardware).

6 files changed, 643 insertions, 5 deletions

diff --git a/CHANGELOG b/CHANGELOG
index a0b6f0594..2b42045b2 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,9 @@
 Changes since U-Boot 1.1.4:
 ======================================================================
 
+* Add support for VirtLab2 board
+  (needed because of differences in the PCMCIA hardware).
+
 * Minor cleanup.
 
 * Update yosemite configuration to enable flash write buffer support
diff --git a/Makefile b/Makefile
index fa7a4a704..2a05e27b7 100644
--- a/Makefile
+++ b/Makefile
@@ -756,7 +756,8 @@ TQM850M_config		\
 TQM855M_config		\
 TQM860M_config		\
 TQM862M_config		\
-TQM866M_config:		unconfig
+TQM866M_config		\
+virtlab2_config:	unconfig
 	@ >include/config.h
 	@[ -z "$(findstring _LCD,$@)" ] || \
 		{ echo "#define CONFIG_LCD"		>>include/config.h ; \
diff --git a/board/tqm8xx/tqm8xx.c b/board/tqm8xx/tqm8xx.c
index 520bea873..b292231c9 100644
--- a/board/tqm8xx/tqm8xx.c
+++ b/board/tqm8xx/tqm8xx.c
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2004
+ * (C) Copyright 2000-2006
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -124,6 +124,9 @@ int checkboard (void)
 			break;
 		putc (*s);
 	}
+#ifdef CONFIG_VIRTLAB2
+	puts (" (Virtlab2)");
+#endif
 	putc ('\n');
 
 	return (0);
diff --git a/common/cmd_pcmcia.c b/common/cmd_pcmcia.c
index 62446d4ef..16d9d1409 100644
--- a/common/cmd_pcmcia.c
+++ b/common/cmd_pcmcia.c
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2004
+ * (C) Copyright 2000-2006
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -718,7 +718,8 @@ static int hardware_disable(int slot)
 /* SC8xx   Boards by SinoVee Microsystems				*/
 /* -------------------------------------------------------------------- */
 
-#if defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx)
+#if (defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx)) \
+	&& !defined(CONFIG_VIRTLAB2)
 
 #if defined(CONFIG_TQM8xxL)
 #define PCMCIA_BOARD_MSG "TQM8xxL"
@@ -1021,6 +1022,174 @@ done:
 
 #endif	/* TQM8xxL */
 
+/* -------------------------------------------------------------------- */
+/* Virtlab2 Board by TQ Components					*/
+/* -------------------------------------------------------------------- */
+
+#if defined(CONFIG_VIRTLAB2)
+#define PCMCIA_BOARD_MSG "Virtlab2"
+
+static int hardware_enable(int slot)
+{
+	volatile pcmconf8xx_t	*pcmp =
+		(pcmconf8xx_t *)&(((immap_t *)CFG_IMMR)->im_pcmcia);
+	volatile unsigned char	*powerctl =
+		(volatile unsigned char *)PCMCIA_CTRL;
+	unsigned int		reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(slot);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
+
+	/*
+	 * Disable interrupts, DMA, and PCMCIA buffers
+	 * (isolate the interface) and assert RESET signal
+	 */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg = __MY_PCMCIA_GCRX_CXRESET;		/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	/* remove all power */
+	*powerctl = 0;
+
+	/*
+	 * Make sure there is a card in the slot, then configure the interface.
+	 */
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n", __LINE__,__FUNCTION__,
+		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	 * Power On.
+	 */
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
+		(reg&PCMCIA_VS1(slot))?"n":"ff",
+		(reg&PCMCIA_VS2(slot))?"n":"ff");
+
+	if ((reg & mask) == mask) {
+		*powerctl = 2;	/* Enable 5V Vccout */
+		puts (" 5.0V card found: ");
+	} else {
+		*powerctl = 1;	/* Enable 3.3 V Vccout */
+		puts (" 3.3V card found: ");
+	}
+
+	udelay(1000);
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(slot);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+
+	PCMCIA_PGCRX(slot) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+static int hardware_disable(int slot)
+{
+	volatile unsigned char	*powerctl =
+		(volatile unsigned char *)PCMCIA_CTRL;
+	unsigned long		 reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	/* remove all power */
+	*powerctl = 0;
+
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg = __MY_PCMCIA_GCRX_CXRESET;		/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+
+	PCMCIA_PGCRX(slot) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif
+
+static int voltage_set(int slot, int vcc, int vpp)
+{
+	volatile pcmconf8xx_t	*pcmp =
+		(pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	volatile unsigned char	*powerctl =
+		(volatile unsigned char *)PCMCIA_CTRL;
+	unsigned long		reg;
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG
+		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	/*
+	 * Disable PCMCIA buffers (isolate the interface)
+	 * and assert RESET signal
+	 */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(slot);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	/*
+	 * Configure pins for 5 Volts Enable and 3 Volts enable,
+	 * Turn off all power.
+	 */
+	debug ("PCMCIA power OFF\n");
+	reg = 0;
+	switch(vcc) {
+	case  0: 		break;
+	case 33: reg = 0x0001;	break;
+	case 50: reg = 0x0002;	break;
+	default: 		goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n", pcmp->pcmc_pipr,
+		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	*powerctl = reg;
+
+	if (reg) {
+		debug ("PCMCIA powered at %sV\n", (reg&0x0004) ? "5.0" : "3.3");
+	} else {
+		debug ("PCMCIA powered down\n");
+	}
+
+done:
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(slot);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", slot+'A');
+	return (0);
+}
+#endif	/* CONFIG_VIRTLAB2 */
 
 /* -------------------------------------------------------------------- */
 /* LWMON Board								*/
diff --git a/include/commproc.h b/include/commproc.h
index 790016655..061468e75 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -2,7 +2,7 @@
  * MPC8xx Communication Processor Module.
  * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
  *
- * (C) Copyright 2000-2004
+ * (C) Copyright 2000-2006
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * This file contains structures and information for the communication
@@ -1412,6 +1412,7 @@ typedef struct scc_enet {
     defined(CONFIG_TQM823L) || defined(CONFIG_TQM823M) || \
     defined(CONFIG_TQM850L) || defined(CONFIG_TQM850M) || \
     defined(CONFIG_ETX094)  || defined(CONFIG_RRVISION)|| \
+    defined(CONFIG_VIRTLAB2)||				  \
    (defined(CONFIG_LANTEC) && CONFIG_LANTEC < 2)
 /* Bits in parallel I/O port registers that have to be set/cleared
  * to configure the pins for SCC2 use.
diff --git a/include/configs/virtlab2.h b/include/configs/virtlab2.h
new file mode 100644
index 000000000..06d8536ec
--- /dev/null
+++ b/include/configs/virtlab2.h
@@ -0,0 +1,461 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
+#define CONFIG_VIRTLAB2		1	/* ...on a virtlab2 module	*/
+#define	CONFIG_TQM8xxL		1
+
+#ifdef	CONFIG_LCD			/* with LCD controller ?	*/
+#define	CONFIG_SPLASH_SCREEN		/* ... with splashscreen support*/
+#endif
+
+#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
+#undef	CONFIG_8xx_CONS_SMC2
+#undef	CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
+
+#define	CONFIG_BOOTCOUNT_LIMIT
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#define CONFIG_BOARD_TYPES	1	/* support board types		*/
+
+#define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"flash_nfs=run nfsargs addip;"					\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip;"					\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
+	"rootpath=/opt/eldk/ppc_8xx\0"					\
+	"bootfile=/tftpboot/TQM823L/uImage\0"				\
+	"kernel_addr=40040000\0"					\
+	"ramdisk_addr=40100000\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#if defined(CONFIG_LCD)
+# undef	 CONFIG_STATUS_LED		/* disturbs display		*/
+#else
+# define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
+#endif	/* CONFIG_LCD */
+
+#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
+
+#ifdef	CONFIG_SPLASH_SCREEN
+# define CONFIG_COMMANDS      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_ASKENV	| \
+				CFG_CMD_BMP	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_NFS	| \
+				CFG_CMD_SNTP	)
+#else
+# define CONFIG_COMMANDS      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_ASKENV	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_NFS	| \
+				CFG_CMD_SNTP	)
+#endif
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
+
+#if 0
+#define	CFG_HUSH_PARSER		1	/* use "hush" command parser	*/
+#endif
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE		256	/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS		16	/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR		0x100000	/* default load address	*/
+
+#define	CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0x40000000
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define	CFG_ENV_IS_IN_FLASH	1
+#define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
+#define CFG_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
+#define CFG_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#ifndef	CONFIG_CAN_DRIVER
+#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#else	/* we must activate GPL5 in the SIUMCR for CAN */
+#define CFG_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#endif	/* CONFIG_CAN_DRIVER */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ */
+#define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
+			 SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR	(0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR	(0xEC000000)
+#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
+
+#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
+#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
+#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
+
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
+
+#define CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O			*/
+#define CFG_ATA_DATA_OFFSET	(CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	(2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers	*/
+#define CFG_ATA_ALT_OFFSET	0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER	0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
+#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
+#define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
+
+/*
+ * FLASH timing:
+ */
+#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
+				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
+
+#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+#define CFG_OR1_REMAP	CFG_OR0_REMAP
+#define CFG_OR1_PRELIM	CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
+#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
+#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
+#define CFG_OR_TIMING_SDRAM	0x00000A00
+
+#define CFG_OR2_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#ifndef	CONFIG_CAN_DRIVER
+#define	CFG_OR3_PRELIM	CFG_OR2_PRELIM
+#define CFG_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
+#define	CFG_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
+#define CFG_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
+#define CFG_OR3_CAN		(CFG_CAN_OR_AM | OR_G5LA | OR_BI)
+#define CFG_BR3_CAN		((CFG_CAN_BASE & BR_BA_MSK) | \
+					BR_PS_8 | BR_MS_UPMB | BR_V )
+#endif	/* CONFIG_CAN_DRIVER */
+
+/*
+ * Memory Periodic Timer Prescaler
+ *
+ * The Divider for PTA (refresh timer) configuration is based on an
+ * example SDRAM configuration (64 MBit, one bank). The adjustment to
+ * the number of chip selects (NCS) and the actually needed refresh
+ * rate is done by setting MPTPR.
+ *
+ * PTA is calculated from
+ *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
+ *
+ *	gclk	  CPU clock (not bus clock!)
+ *	Trefresh  Refresh cycle * 4 (four word bursts used)
+ *
+ * 4096  Rows from SDRAM example configuration
+ * 1000  factor s -> ms
+ *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
+ *    4  Number of refresh cycles per period
+ *   64  Refresh cycle in ms per number of rows
+ * --------------------------------------------
+ * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
+ *
+ * 50 MHz => 50.000.000 / Divider =  98
+ * 66 Mhz => 66.000.000 / Divider = 129
+ * 80 Mhz => 80.000.000 / Divider = 156
+ */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
+
+/*
+ * For 16 MBit, refresh rates could be 31.3 us
+ * (= 64 ms / 2K = 125 / quad bursts).
+ * For a simpler initialization, 15.6 us is used instead.
+ *
+ * #define CFG_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
+ * #define CFG_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
+ */
+#define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
+#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+/* Map peripheral control registers on CS4 */
+#define CFG_PERIPHERAL_BASE 0xA0000000
+#define CFG_PERIPHERAL_OR_AM 0xFFFF8000 /* 32 kB address mask */
+#define CFG_OR4_PRELIM (CFG_PERIPHERAL_OR_AM | OR_TRLX | OR_CSNT_SAM | \
+						OR_SCY_2_CLK)
+#define CFG_BR4_PRELIM ((CFG_PERIPHERAL_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
+#define PCMCIA_CTRL (CFG_PERIPHERAL_BASE + 0xB00)
+#endif	/* __CONFIG_H */